Design variations of a polymer–enzyme composite biosensor for glucose: Enhanced analyte sensitivity without increased oxygen dependence

The glucose sensitivity and oxygen dependence of a variety of implantable biosensors based on glucose oxidase (GOx), incorporating an electrosynthesized poly-o-phenylenediamine (PPD) permselective barrier on 125-μm diameter Pt disks (Pt_D) and cylinders (Pt_C, 1-mm length), were measured and compared. Full glucose calibrations and experimental monitoring of solution oxygen concentration allowed us to determine apparent Michaelis–Menten parameters for glucose and oxygen. In the linear region of glucose response, the most sensitive biosensor design studied was Pt_D/PPD/GOx (enzyme deposited over polymer) that was 20 times more sensitive than the more widely used Pt_C/GOx/PPD (enzyme immobilized before polymer deposition) configuration. The oxygen dependence, quantified as K_M(O₂), of both active and less active designs was surprisingly similar, a finding that could be rationalized in terms of an increase in K_M(G) with increased enzyme loading. The Pt_D/PPD/GOx design will now enable us to explore glucose concentration dynamics in smaller and layered brain regions with good sensitivity and minimal interference from fluctuations in tissue pO₂.     

Construction of glucose biosensor based on sorption of glucose oxidase onto multilayers of polyelectrolyte/nanoparticles

A new approach to constructing an enzyme-containing film on the surface of a gold electrode for use as a biosensor is described. A basic multilayer film (BMF) of (PDDA/GNPs) _n /PDDA was first constructed on the gold electrode by electrostatic layer-by-layer self-assembly of poly(diallyldimethylammonium chloride) (PDDA) and gold nanoparticles (GNPs). Glucose oxidase (GOx) was then sorbed into this BMF by dipping the BMF-modified electrode into a GOx solution. The assembly of the BMF was monitored and tested via UV-vis spectroscopy and cyclic voltammetry (CV). The ferrocenemethanol-mediated cyclic voltammograms obtained from the gold electrode modified with the (PDDA/GNPs) _n /PDDA/GOx indicated that the assembled GOx remained electrocatalytically active for the oxidation of glucose. Analysis of the voltammetric signals showed that the surface coverage of active enzyme was a linear function of the number of PDDA/GNPs bilayers. This result confirmed the penetration of GOx into the BMF and suggests that the BMF-based enzyme film forms in a uniform manner. Electrochemical impedance measurements revealed that the biosensor had a lower electron transfer resistance (R _et) than that of a sensor prepared by layer-by-layer assembly of PDDA and GOx, due to the presence of gold nanoparticles. The sensitivity of the biosensor for the determination of glucose, which could be controlled by adjusting the number of PDDA/GNPs bilayers, was investigated.     

基于多壁碳纳米管和氧化锌纳米棒复合物的葡萄糖生物传感器(英文)

利用多壁碳纳米管(MWCNTs)和氧化锌(ZnO)纳米棒复合物膜构建了一种新的电流型葡萄糖生物传感器。MWCNTs-ZnO复合物在超声协助下通过静电配位的方式产生。其中,ZnO纳米棒的存在加强了该复合物催化氧化H2O2的能力,增加了响应电流。与单一的MWCNTs和ZnO相比,这种纳米复合物显示了更为有效地电催化活性。在此基础上,我们以MWCNTs-ZnO复合物膜为基底,用戊二醛交联法固定葡萄糖氧化酶,电聚合邻苯二胺(PoPD)膜为抗干扰层,构建了抗干扰能力强,稳定性好,灵敏度高,响应快的葡萄糖传感器。在+0.8V的检测电位下,该传感器对葡萄糖响应的线性范围为5.0×10-6~5.0×10-3mol·L-1(R=0.997),检测限为3.5×10-6mol·L-1(S/N=3),响应时间小于10s的葡萄糖生物传感器,常见干扰物质如抗坏血酸和尿酸不影响测定。     

Tin disulfide nanoflakes decorated with gold nanoparticles for direct electrochemistry of glucose oxidase and glucose biosensing

Previously, we have prepared nanoflake-like tin disulfide (SnS2) and used for the immobilization of proteins and biosensing. We have now modified an electrode with a composite consisting of nanoflake-like SnS2 decorated with gold nanoparticles (Au-NPs) and have immobilized glucose oxidase (GOx) on its surface in order to study its direct electrochemistry. Scanning electron microscopy, electrochemical impedance spectroscopy, Fourier transform IR spectroscopy and cyclic voltammetry were used to examine the interaction between GOx and the AuNP-SnS2 film. It is shown that the composite film has a larger surface area and offers a microenvironment that facilitates the direct electron transfer between enzyme and electrode surface. The immobilized enzyme retains its bioactivity and undergoes a surface-controlled, reversible 2-proton and 2-electron transfer reaction, with an apparent electron transfer rate constant of 3.87 s ^-1. Compared to the nanoflake-like SnS2-based glucose sensor, the GOx-based biosensor exhibits a lower detection limit (1.0 :M), a better sensitivity (21.8 mA?M ^-1 ?cm ^-2), and a wider linear range (from 0.02 to 1.3 mM). The sensor displays excellent selectivity, good reproducibility, and acceptable stability. It was successfully applied to reagentless sensing of glucose at ?0.43 V.

A gold@silica core–shell nanoparticle-based surface-enhanced Raman scattering biosensor for label-free glucose detection

The gold nanostar@silica core–shell nanoparticles conjugated with glucose oxidase (GOx) enzyme molecules have been developed as the surface-enhanced Raman scattering (SERS) biosensor for label-free detection of glucose. The surface-immobilized GOx enzyme catalyzes the oxidation of glucose, producing hydrogen peroxide. Under laser excitation, the produced H₂O₂ molecules near the Au nanostar@silica nanoparticles generate a strong SERS signal, which is used to measure the glucose concentration. The SERS signal of nanostar@silica∼GOx nanoparticle-based sensing assay shows the dynamic response to the glucose concentration range from 25 μM to 25 mM in the aqueous solution with the limit of detection of 16 μM. The sensing assay does not show any interference when glucose co-exists with both ascorbic acid and uric acid. The sensor can be applied to a saliva sample.     

Immobilization of glucose oxidase on rod-like and vesicle-like mesoporous silica for enhancing current responses of glucose biosensors

The use of rod-like and vesicle-like mesoporous SiO₂ particles for fabricating high performance glucose biosensors is reported. The distinctively high surface areas of mesoporous structures of SiO₂ rendered the adsorption of glucose oxidase (GOx) feasible. Both morphologies of SiO₂ enhanced the sensitivities of glucose biosensors, but by a factor of 36 for vesicle-like SiO₂ and 18 for rod-like SiO₂, respectively. The greater enhancement of vesicle-like SiO₂ can be accounted for by its higher specific surface area (509 m² g⁻¹) and larger total pore volume (1.49 cm³ g⁻¹). Interestingly, the current responses of GOx immobilized in interior channels of the mesoporous SiO₂ were enhanced much more than those of simple mixtures of GOx and the mesoporous SiO₂. This suggests that the enhancement of current responses arise not only from the high surface area of SiO₂ for high enzyme loading, but also from the improved enzyme activity upon its adsorption on mesoporous SiO₂. Also compared were the performances of glucose biosensors with GOx immobilized on mesoporous SiO₂ by physical adsorption and by covalent binding to 3-aminopropyltrimethoxysilane (APTMS) modified SiO₂ using glutaraldehyde as the cross-linker. The covalent binding approach resulted in higher enzyme loading but lower current sensitivity than with the physical adsorption.     

Integrated Microcentrifuge Carbon Entrapped Glucose Oxidase Poly (N-Isopropylacrylamide) (pNIPAm) Microgels for Glucose Amperometric Detection

This study demonstrates a miniaturized integrated glucose biosensor based on a carbon microbeads entrapped by glucose oxidase (GOx) immobilized on poly (N-isopropylacrylamide) (pNIPAm) microgels. Determined by the Lowry protein assay, the pNIPAm microgel possesses a high enzyme loading capacity of 31?mg/g. The pNIPAm GOx loaded on the microgel was found to maintain a high activity of approximately 0.140?U determined using the 4-aminoantipyrine colorimetric method. The integrated microelectrochemical cell was constructed using a microcentrifuge vial housing packed with (1:1, w/w) carbon entrapped by pNIPAm GOx microgels, which played the dual role of the microbioreactor and the working electrode. The microcentrifuge vial cover was used as a miniaturized reference electrode and an auxiliary electrode holder. The device can work as biosensor, effectively converting glucose to H₂O₂, with subsequent amperometric detection at an applied potential of ?0.4?V. The microelectrochemical biosensor was used to detect glucose in wide linear range from 30?µM to 8.0?mM, a low detection limit of 10?µM, a good linear regression coefficient (R²) of 0.994, and a calibration sensitivity of 0.0388?µA/mM. The surface coverage of active GOx, electron transfer rate constant (ks), and Michaelis–Menten constant (K_M^app) of the immobilized GOx were 4.0?×?10^?11?mol/cm², 5.4?s^?1, and 0.086?mM, respectively. To demonstrate the applicability and robustness of the biosensor for analysis of high sample matrix environment, glucose was analyzed in root beer. The microelectrochemical device was demonstrated for analysis of small sample (<50?µL), while affording high precision and fast signal measurement (≤5?s).     

Glucose oxidase immobilized on magnetic nanoparticles: Nanobiosensors for fluorescent glucose monitoring

The authors describe enzyme based nanobiosensors for continuous monitoring of glucose, with the long term goal of using them as smart diagnostic tattoos. The method is founded on two main features: (1) The fluorescence intensity and decay times of glucose oxidase (GOx) and of GOx labeled with fluorescein (FS) or a ruthenium chelate (Ru) reversibly change during interaction with glucose; (2) The (labeled) enzyme is linked to magnetite magnetic nanoparticles (MNPs) which permits the MNPs to be physically manipulated. It is found that a stable link between MNPs and GOx is only accomplished if the number of amino groups on the GOX is artificially enlarged (to form GOx_sam). Fluorescence decay data are best acquired with 8-nm MNPs where scattering is marginal; The activity of GOx is found not to be affected by immobilization on the MNPs. The various immobilized enzymes (GOx_sam, GOx_sam-FS and GOx_sam-Ru; all on MNPs) differ only slightly in terms of linear response to glucose which ranged from 0.5 mM to at least 3.5 mM. The RSDs are about 5% (for n = 5), the detection limits are at ～50 μM, and the sensor lifetimes are >1 week.

Open image in new window

Graphical abstract Nanobiosensors consisting of Fe₃O₄ magnetic nanoparticles linked to glucose oxidase, previously enriched with amino groups (GOx_sam) and containing fluorescein (FS) or a ruthenium derivative (Ru), are presented as a new kind of smart tattoos for glucose monitoring.

     

Electrochemical Glucose Biosensors: Whole Cell Microbial and Enzymatic Determination Based on 10-(4H-Dithieno[3,2-b:2′,3′-d]Pyrrol-4-yl)Decan-1-Amine Interfaced Glassy Carbon Electrodes

The fabrication of amperometric biosensors based on whole cell Gluconobacter oxydans DSMZ 2343 (G. oxydans) and glucose oxidase (GOx) was performed for the detection of glucose. Glassy carbon electrodes (GCE) were coated with a 10-(4H-dithiyeno [3,2-b:2’,3’-d]pyroll-4-il)decan-1-amine (DTP-alkyl-NH₂) polymer using an electropolymerization method and the formed interface was used to connect the bacteria and the enzyme to the electrode. The transfer of electrons from enzyme to electrode was successfully demonstrated by the biocatalytic activity and unique morphology of the conducting polymer. Characterization of the biosensors was assessed using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM) analyses. The detection limits of the enzyme and microbial based biosensors for glucose were 0.022 and 0.081?mM, respectively. The broad linear dynamic ranges of the GOx and G. oxydans biosensors were observed to be 0.045–50.0 and 0.19–50.0?mM, respectively. The analytical performances of biosensors were compared according to the following figures of merit: detection limits, limits of quantification, pH and current response time. In addition, to demonstrate the applicability of the biosensors, real-time measurements and recovery studies were evaluated.     

基于二氧化钛/碳纳米管/壳聚糖纳米复合薄膜制备葡萄糖生物传感器

利用壳聚糖(CHI)溶液分散了纳米二氧化钛(nano-TiO2)和多壁碳纳米管(MWCNT),将该分散液修饰于玻碳电极表面形成纳米复合薄膜;用戊二醛为交联剂在该纳米复合层上固定了葡萄糖氧化酶(GOx),同时以二茂铁为电子媒介体构建了一种新型葡萄糖传感器。利用扫描电镜(SEM)、交流阻抗(AC)对所制备的传感器进行了表征,同时用循环伏安法(CV)和计时电流法(CA)考察了其对葡萄糖的电催化氧化性能。实验结果表明,在优化测试条件下该传感器对葡萄糖在0.5～20.0 mmol.L-1范围内有线性响应,检出限为0.2 mmol.L-1;电流达到95%的稳态时间小于5 s;此生物传感器具有良好的重现性和选择性,能有效排除抗坏血酸、尿酸等常见干扰物的影响并成功应用于饮料中葡萄糖含量的测定。     

Direct Electrochemistry of Glucose Oxidase at Reduced Graphene Oxide and β‐Cyclodextrin Composite Modified Electrode and Application for Glucose Biosensing

A simple glucose biosensor has been developed based on direct electrochemistry of glucose oxidase (GOx) immobilized on the reduced graphene oxide (RGO) and β‐cyclodextrin (CD) composite. A well‐defined redox couple of GOx appears with a formal potential of ～?0.459 V at RGO/CD composite. A heterogeneous electron transfer rate constant (K_s) has been calculated for GOx at RGO/CD as 3.8 s^?1. The fabricated biosensor displays a wide response to glucose in the linear concentrations range from 50 µM to 3.0 mM. The sensitivity and limit of detection of the biosensor is estimated as 59.74 µA mM^?1 cm^?2 and 12 µM, respectively.     

An Amperometric Glucose Biosensor Based on Poly (Pyrrole‐2‐Carboxylic Acid)/Glucose Oxidase Biocomposite

A newly developed amperometric glucose biosensor based on graphite rod (GR) working electrode modified with biocomposite consisting of poly (pyrrole‐2‐carboxylic acid) (PCPy) particles and enzyme glucose oxidase (GOx) was investigated. The PCPy particles were synthesized by chemical oxidative polymerization technique using H₂O₂ as initiator of polymerization reaction and modified covalently with the GOx (PCPy‐GOx) after activation of carboxyl groups located on the particles surface with a mixture of N‐(3‐dimethylaminopropyl)‐N′‐ethylcarbodiimide hydrochloride (EDC) and N‐hydroxysuccinimide (NHS). Then the PCPy‐GOx biocomposite was dispersed in a buffer solution containing a certain amount of bovine serum albumin (BSA). The resulting biocomposite suspension was adsorbed the on GR electrode surface with subsequent solvent airing and chemical cross‐linking of the proteins with glutaraldehyde vapour (GR/PCPy‐GOx). It was determined that the current response of the GR/PCPy‐GOx electrodes to glucose measured at +300 mV vs Cl reference electrode was influenced by the duration of the PCPy particles synthesis, pH of the GOx solution used for the PCPy particles modification and the amount of immobilized PCPy‐GOx biocomposite. An optimal pH of buffer solution for operation of the biosensor was found to be 8.0. Detection limit was determined as 0.039 mmol L⁻¹ according signal to noise ratio (S/N: 3). The proposed glucose biosensor was tested in human serum samples.     

Determination of trace chromium(VI) by an inhibition-based enzyme biosensor incorporating an electropolymerized aniline membrane and ferrocene as electron transfer mediator

A novel inhibition-based glucose oxidase (GOx) biosensor for environmental chromium(VI) detection is described. An electropolymerized aniline membrane has been prepared on a platinum electrode containing ferrocene as electron transfer mediator, on which GOx is cross-linked by glutaraldehyde. The mechanism of the redox reaction on the electrode and the performance of the sensor are studied. The sensor's response to glucose decreases when it is inhibited by chromium(VI), with a lower detection limit of 0.49?µg?L^?1, and the linear response range is divided into two parts, one of which is 0.49–95.73?µg?L^?1 and the other is 95.73?µg^?1 to8.05?mg?L^?1. The enzyme membrane is shown to be completely reactivated after inhibition, retaining 90% activity over more than forty days. Interference to chromium(VI) determination from lead(II), copper(II), cadmium(II), chromium(III), cobalt(II), tin(II) and nickel(II) is found to be minimal, while high concentrations of mercury(II) and silver(I) may interfere with the determination of trace chromium(VI). The sensor has been used for chromium(VI) determination in soil samples with good results.     

Direct Electrochemistry and Electrocatalysis Behaviors of Glucose Oxidase Based on Hyaluronic Acid-Carbon Nanotubes-Ionic Liquid Composite Film

Multi‐walled carbon nanotubes (MWNTs) were dispersed in the ionic liquid [BMIM][BF₄] to form a uniform black suspension. Based on it, a novel glucose oxidase (GOx)‐hyaluronic (HA)‐[BMIM][BF₄]‐MWNTs/GCE modified electrode was fabricated. UV‐vis spectroscopy confirmed that GOx immobilized in the composite film retained its native structure. The experimental results of EIS indicated MWNTs, [BMIM][BF₄] and HA were successfully immobilized on the surface of GCE and [BMIM][BF₄]‐MWNTs could obviously improve the diffusion of ferricyanide toward the electrode surface. The experimental results of CV showed that a pair of well‐defined and quasi‐reversible peaks of GOx at the modified electrode was exhibited, and the redox reaction of GOx at the modified electrode was surface‐confined and quasi‐reversible electrochemical process. The average surface coverage of GOx and the apparent Michaelis‐Menten constant were 8.5×10⁻⁹ mol/cm² and 9.8 mmol/L, respectively. The cathodic peak current of GOx and the glucose concentration showed linear relationship in the range from 0.1 to 2.0 mmol/L with a detection limit of 0.03 mmol/L (S/N=3). As a result, the method presented here could be easily extended to immobilize and obtain the direct electrochemistry of other redox enzymes or proteins.     

Direct electrochemistry and biocatalysis of glucose oxidase immobilized on magnetic mesoporous carbon

A magnetic mesoporous carbon material (i.e., mesoporous iron oxide/C, mesoFe/C) is synthesized for protein immobilization, using glucose oxidase (GOx) as model. Transmission electron microscopy images show that mesoFe/C has highly ordered porous structure with uniform pore size, and iron oxide nanoparticles are dispersed along the wall of carbon. After adsorption of GOx, the GOx-mesoFe/C composite is separated with magnet. The immobilized GOx remains its natural structure according to the reflection–absorption infrared spectra. When the GOx-mesoFe/C composite is coated on a Pt electrode surface, the GOx gives a couple of quasireversible voltammetric peaks at −0.5 V (vs. saturated calomel electrode) due to the redox of FAD/FADH₂. The electron-transfer rate constant (k _s) is ca. 0.49 s⁻¹. The modified electrode presents remarkably amperometric response to glucose at 0.6 V. The response time (t _95%) is less than 6 s; the response current is linear to glucose concentration in the range of 0.2–10 mM with a sensitivity of 27 μA mM⁻¹ cm⁻². The detection limit is 0.08 mM (S/N = 3). The apparent Michaelis–Menten constant (K _m^app) of the enzyme reaction is ca. 6.6 mM, indicating that the GOx immobilized with mesoFe/C has high affinity to the substrate.     

A blood-assisted optical biosensor for automatic glucose determination

A new approach for glucose determination in blood based on the spectroscopic properties of blood hemoglobin (Hb) is presented. The biosensor consists of a glucose oxidase (GOx) entrapped polyacrylamide (PAA) film placed in a flow cell. Blood is simply diluted with bidistilled water (150:1, v:v) and injected into the carrier solution. When reaching the PAA film, the blood glucose reacts with the GOx and the resulting H₂O₂ reacts with the blood Hb. This produces an absorbance change in this compound. The GOx-PAA film can be used at least 100 times. Lateral reactions of H₂O₂ with other blood constituents are easily blocked (by azide addition). The linear response range can be fitted between 20 and 1200 mg dL⁻¹ glucose (R.S.D. 4%, 77 mg dL⁻¹). In addition to the use of untreated blood, two important analytical aspects of the method are: (1) the analyte concentration can be obtained by an absolute calibration method; and (2) the signal is not dependent on the oxygen concentration.A mathematical model relating the Hb absorbance variation during the reaction with the glucose concentration has been developed to provide theoretical support and to predict its application to other compounds after changing the GOx by another enzyme. The method has been applied to direct glucose determination in 10 blood samples, and a correlation coefficient higher than 0.98 was obtained after comparing the results with those determined by an automatic analyzer. As well as sharing some of the advantages of disposable amperometric biosensors, the most significant feature of this approach is its reversibility.     

Multilayered construction of glucose oxidase on gold electrodes based on layer-by-layer covalent attachment

A feasible approach to construct multilayered enzyme film on the gold electrode surface for use as biosensing interface is described. The film was fabricated by alternate layer-by-layer deposition of periodate-oxidized glucose oxidase (GOx) and poly(allylamine) (PAA). The covalent attachment process was followed and confirmed by electrochemical impedance spectroscopy (EIS). X-ray diffraction (XRD) experiments revealed that the film was homogeneous and formed in an ordered manner with a thickness of 2.6 ± 0.1 nm per bilayer. The gold electrodes modified with the GOx/PAA multilayers showed excellent electrocatalytical response to the oxidation of glucose when ferrocenemethanol was used as an artificial redox mediator, which was studied by cyclic voltammetry (CV). From the analysis of voltammetric signals, the coverage of active enzyme on the electrode surface was estimated, which had a linear relationship with the number of GOx/PAA bilayers. This suggests that the analytical performance such as sensitivity, detection limit, and so on, is tunable by controlling the number of attached bilayers. The six GOx/PAA bilayer electrode exhibited a sensitivity of 15.1 μA mM⁻¹ cm⁻² with a detection limit of 3.8 × 10⁻⁶ M. In addition, the sensor exhibited good reproducibility and stability.     

Enhanced amperometric response of a glucose oxidase and horseradish peroxidase based bienzyme glucose biosensor modified with a film of polymerized toluidine blue containing reduced graphene oxide

Reduced graphene oxide (RGO) was used to construct a bienzyme biosensor containing horseradish peroxidase (HRP) and glucose oxidase (GOx). A poly(toluidine blue) (pTB) film containing RGO acted as both enzyme immobilization matrix and electron transfer mediator. The bienzyme biosensor was characterized by electrochemical techniques and displays a highly sensitive amperometric response to glucose and hydrogen peroxide (H₂O₂) at a potential as low as −0.1 V (vs. SCE). It is shown that use of RGO causes a strong enhancement on the amperometric responses. H₂O₂ formed by the action of GOx in the presence of oxygen can be further reduced by HRP in the pTB film contacting the RGO modified electrode. In the absence of oxygen, glucose oxidation proceeds by another mechanism in which electron transfer occurs from GOx to the electrode and with pTB acting as the mediator. Amperometric responses to glucose and H₂O₂ follow Michaelis-Menten kinetics. The experimental conditions were optimized, and under these conditions glucose can be determined in the 80 μM to 3.0 mM range with a detection limit of 50 μM. H₂O₂, in turn, can be quantified in up to 30.0 μM concentration with a detection limit of 0.2 μM. The bienzyme biosensor is reproducible, repeatable and stable. Finally, it has been successfully applied to the determination of glucose in plasma samples.

Schematic representation of glocuse detection at GCE/RGO/pTB-HRP-GOx.

     

A Breathing Atom‐Transfer Radical Polymerization: Fully Oxygen‐Tolerant Polymerization Inspired by Aerobic Respiration of Cells

The first well‐controlled aqueous atom‐transfer radical polymerization (ATRP) conducted in the open air is reported. This air‐tolerant ATRP was enabled by the continuous conversion of oxygen to carbon dioxide catalyzed by glucose oxidase (GOx), in the presence of glucose and sodium pyruvate as sequential sacrificial substrates. Controlled polymerization using initiators for continuous activator regeneration (ICAR) ATRP of oligo(ethylene oxide) methyl ether methacrylate (OEOMA, M_n=500) yielded polymers with low dispersity (1.09≤?≤1.29) and molecular weights (MWs) close to theoretical values in the presence of pyruvate. Without added pyruvates, lower MWs were observed due to generation of new chains by H₂O₂ formed by reaction of O₂ with GOx. Successful chain extension of POEOMA₅₀₀ macroinitiator with OEOMA₃₀₀ (?≤1.3) and Bovine Serum Albumin bioconjugates (?≤1.22) confirmed a well‐controlled polymerization. The reactions in the open air in larger scale (25 mL) were also successful.     

Synthesis of Poly(<Emphasis Type="Italic">o</Emphasis>-anisidine)/H<Subscript>2</Subscript>SO<Subscript>4</Subscript> Film for the Development of Glucose Biosensor

The poly(o-anisidine)–sulfuric acid–glucose oxidase (POA–H₂SO₄–GOx) electrode has been investigated in the present work. Platinum electrode was used for the synthesis of poly (o-anisidine)–sulfuric acid (POA–H₂SO₄) film using galvanostatic method with 0.2 M o-anisidine, 1.0 M H₂SO₄ solution, 1.0 pH and 2 mA/cm² applied current density. The synthesized film was characterized using electrochemical technique, conductivity measurement, UV–visible spectroscopy, Fourier transform infrared spectroscopy, and scanning electron microscopy. GO_X was immobilized on synthesized POA–H₂SO₄ film by cross-linking via glutaraldehyde in phosphate and acetate buffer. The Michaelis–Menten constant ( K_\textm￠K_{\text{m}}^\prime ) was determined for the immobilized enzyme. The glucose oxidase electrode shows the maximum current response at pH 5.5 and potential 0.6 V. The sensitivity of POA–H₂SO₄–GO_X electrode in phosphate and acetate buffer has been recorded. The results of this study reveal that the phosphate buffer gives fast response as compared to acetate buffer in amperometric measurements.