A thermal decomposition study of polymers by tunable synchrotron vacuum ultraviolet photoionization mass spectrometry

The thermal decomposition of polymers (poly(vinyl chloride) (PVC) and polystyrene (PS)) has been studied with synchrotron VUV photoionization mass spectrometry at low pressure. Pyrolysis products formed at different temperatures have been identified by the measurement of photoionization mass spectra at different photon energies. The experimental results demonstrate the variation of the pyrolysis product pool of PVC at different temperatures, dividing the thermal decomposition process into two stages: the low‐temperature stage to form HCl and benzene, and the high‐temperature stage to form numerous large aromatic hydrocarbons. For the thermal decomposition of PS, four reaction categories are determined. This work reports a new application of synchrotron VUV photoionization mass spectrometry in the study of the thermal decomposition of polymers, and demonstrates its good performance in product analysis, which is expected to help understand the thermal decomposition mechanism of PVC, PS and other synthesized polymers. Copyright © 2009 John Wiley & Sons, Ltd.     

Re-use of chlorine-containing polymers

Poly(vinyl chloride) (PVC) and some other chlorine-containing polymers belong to one of the most widely applied groups of thermoplastics. Their main disadvantage is the rather limited thermal stability, which requires the addition of heat stabilizers to prevent dehydrochlorination and discolouration. Hydrogen chloride is also the main volatile decomposition product during combustion of PVC; therefore, PVC-waste is less suited for the so-called thermal recycling. For the re-use of PVC and similar polymers it is necessary to characterize these products by molecular weight (or at least viscometry), internal double bonds and other defect structures, stability against the influence of heat (and in some cases of light) and a few other properties. The application of these methods for deciding about the re-usability of PVC roofing sheets and for the injection moulding of PVC scrap is demonstrated.     

Al(OH)3和Mg(OH)2对PVC热解特性的影响研究

利用热重分析仪并借助电导率测定法探讨了Al(OH)3和Mg(OH)2对PVC热解特性的影响,简要分析了其机理。结果表明:加入Al(OH)3和Mg(OH)2后均能增加PVC体系在第一阶段的最大热解速率和残炭量,最大热解速率增加约1倍,残炭量增加约4倍。并且分解产生的结晶水吸收大量的热量,惰性金属氧化物也有利于成核、炭层生长和凝聚,有着明显的阻燃和抑烟作用。HCl毒性气体的释放主要集中在体系的第一阶段,Al(OH)3能促使HCl提前释放,HCl的释放总量增加,Mg(OH)2也能促使HCl提前释放,但HCl的释放总量却是减少的。     

Kinetic and chemical studies of polymer cross-linking using thermal gravimetry and hyphenated methods. Degradation of polyvinylchloride

The chemistry and kinetics of polyvinylchloride (PVC) degradation have been studied using thermal gravimetry and hyphenated spectroscopic methods to identify condensed phase and vapour phase products. A method of kinetic modelling has been devised to estimate Arrhenius parameters for the sequential and competing processes which comprise the thermal decomposition, and to plot concentrations of decomposition intermediates which make up the TG curve. MS and GC-MS have been used to relate the composition of volatile materials to the TG curve and FTIR has related this to changes in the condensed phase. The chemical studies have highlighted a char forming mechanism based on hydrogen disproportionation which results in carbon enrichment and the formation of aliphatic hydrocarbons.     

Studies of the effects of copper, copper(II) oxide and copper(II) chloride on the thermal degradation of poly(vinyl chloride)

Investigations of the pyrolysis of poly(vinyl chloride) (PVC) in the presence of copper metal (Cu), copper(II) oxide (CuO) and copper(II) chloride (CuCl₂) are of potential importance because of the likelihood of the formation of these copper compounds during the thermal degradation of PVC-coated copper wires, a step in the recovery of copper from waste. The presence of Cu, CuO and CuCl₂ (i) retards the thermal degradation of PVC in air and in nitrogen and (ii) decreases the percentages of volatile products produced at both stages of the decomposition. These effects are greatest for PVC-CuO. The presence of copper, CuO or CuCl₂ in PVC has a major effect on the nature of the gaseous emissions of the thermal decomposition in air and in nitrogen. The concentrations of total chlorine, aliphatic hydrocarbons, aromatic hydrocarbons, chlorinated hydrocarbons and soot particulates are all affected relative to an equivalent amount of PVC. These changes are greatest for the PVC-CuO system for which total chlorine emissions in air and nitrogen are reduced by 40% in air and 20% in nitrogen, benzene emissions are reduced by greater than 90% in air and nitrogen, other aromatic and chloroaromatic emissions are reduced, and soot particulate emissions are reduced by more than 50% as the concentrations of aliphatic compounds are increased. These changes are consistent with the presence of copper or its compounds permitting more efficient combustion of the carbon content of the PVC and particularly in the case of PVC-CuO with the removal of chlorine during pyrolysis in the inorganic phase.     

Large‐scale Experimental Study on the Effects of Flooring Materials on Combustion Behavior of Thermoplastics

The effects of flooring materials on the combustion behavior of thermoplastics is investigated. Based on the ISO 9705 fire test setup, an experimental rig was designed. Full‐scale experiments of PP combustion were carried out using five flooring boards, namely gypsum, steel, wood, ceramic tile and PVC. The experimental results indicate that the flooring boards play an important role in the heat release rates of typical thermoplastics combustion. Specifically, the time for the sharp increase of heat release rate is generally later for the flooring boards with larger thermal conductivity, except for the case of PVC. Preliminary analyses suggest that the reason for the exception of PVC is the expansion and carbonization of PVC at high temperature. In addition, experimental results also show that the corresponding peak heat release rate of thermoplastics combustion would be generally smaller for the flooring board with a larger thermal mass, except for the case of gypsum. The primary cause for the exception of gypsum may be the heat absorption by the crystal water released from the gypsum during the burning of hot pool oil.     

Thermal decomposition of polymer mixtures of PVC,PET and ABS containing brominated flame retardant: Formation of chlorinated and brominated organic compounds

The thermal decomposition of various mixtures of acrylonitrile butadiene styrene copolymer (ABS), ABS containing brominated epoxy resin flame retardant and Sb₂O₃, poly(ethylene terephthalate) (PET) and poly(vinyl chloride) (PVC) has been studied in order to clarify the reactions between the components of mixed polymers. More than 40 halogen-containing molecules have been identified among the pyrolysis products of mixed samples. Brominated and chlorinated aromatic esters were detected from the mixtures containing PET and halogen-containing polymers. A series of chlorinated, brominated and mixed chlorinated and brominated phenols and bisphenol A molecules have been identified among the pyrolysis products of polymer mixtures containing flame retarded ABS and PVC. It was established that the decomposition rate curves (DTG) of the mixtures were not simple superpositions of the individual components indicating interactions between the decomposition reactions of the polymer components. The maximal rate of thermal decomposition of both ABS and PET decreases significantly if the mixture contains brominated epoxy flame retardant and Sb₂O₃ synergist. The dehydrochlorination rate of PVC is enhanced in the presence of ABS or PET.     

Investigations on poly(vinyl chloride). IV. Effects of metal chlorides on the thermal decomposition of poly(vinyl chloride)

The effects of various metal oxides upon the thermal decomposition of poly(vinyl chloride) (PVC) were previously reported. In this work, 23 metal chlorides were investigated to determine their effects on the thermal decomposition of PVC by pyrolysis–gas chromatography at 500°C. Each metal chloride exhibits influences on the course of thermal decomposition of PVC almost similar to the corresponding metal oxide except for a few elements; the metal chlorides from acidic metal oxides accelerate the thermal decomposition of PVC, but the metal chlorides from basic metal oxides do not. On comparing the effects of metal oxides and metal chlorides on the thermal decomposition of PVC, most metal chlorides were found to accelerate the thermal decomposition of PVC more than the corresponding metal oxides, owing to ease of addition of the chlorine atoms released from metal chloride to the dehydrochlorinated chains. It is concluded from these results that the thermal decomposition of PVC containing metal salts is markedly influenced by the ease with which chlorine atoms are released from the corresponding metal chloride.     

Combined thermogravimetry and fourier transform infrared spectroscopy techniques for gas evolution analysis

The usefulness of thermogravimetry has been amply demonstrated for a wide variety of material analysis applications. In many instances, however, additional information is required for adequate characterization of the sample and its thermal decomposition behaviour. In this respect, the analysis of evolved gases, or condensed liquids, has proven a highly useful approach. Among the various physical methods used for analysis of the thermal degradation products, infrared spectroscopy has often been found very powerful, being versatile, rapid and widely accessible. In this study, we report a simple new approach in which the evolved gases and condensed liquids from the thermal decomposition of various products are recuperated in an infrared gas cell and on a PVC membrane filter, respectively. The gaseous components were analysed by transmission FT-IR, and the condensed liquid products were examined directly on the PVC membrane by FT-IR in the internal reflexion mode. The technique was used, for example, to examine the pyrolysis products (gases and liquid) of Koberit, a proposed substitute for asbestos. The method was also applied to the study of chemically derivatized asbestos materials in an attempt to unravel the surface chemical modifications.     

Analysis by Raman and infrared spectroscopy combined with theoretical studies on the identification of plasticizer in PVC films

Raman and Fourier Transform infrared spectroscopy were used to study the vibrational spectra in commercial polyvinyl chloride (PVC) flexible films. In order to have insights of the PVC and the plasticizer structures, density functional theory calculations were conducted via B3LYP hybrid functional. The infrared and Raman calculations took into account geometry optimization of the PVC film, the plasticizer DEHA and the convolution of both. The convoluted spectra were then compared with the experimental data. Finally, the thermal stability of the PVC films was checked through one-hour thermal treatment of the samples comprising temperatures ranges from 50 to 200 °C.     

Thermal degradation of silane crosslinked unplasticized PVC

The thermal decomposition behaviour of rigid PVC, crosslinked using bis(γ-trimethoxysilylpropyl)amine as crosslinking agent has been studied. Different thermal stabilizers (tin and lead based) have been used with different crosslinking agent concentrations, and the influence of these factors on the decomposition behaviour in inert atmosphere studied. Results obtained have shown that the main effect of aminosilane is an advance of the first stage of the PVC degradation (i.e. the dehydrochlorination process). Moreover, samples with different concentrations of silane, and at different stages of their processing (i.e. after milling, pressing, crosslinking) have also been used in order to elucidate the influence of these factors on their thermal behaviour. A quantitative kinetic model has been developed and the corresponding kinetic constants have been obtained by modelling the experimental thermogravimetric data. The kinetic parameters obtained have revealed a reduction in the apparent activation energy of the hydrogen chloride loss process, which has shown to be markedly dependent on the thermal stabilizer used.     

Differential thermal analysis of the mixtures of silicon and red lead

There are two different opinions in the literature on the combustion mechanism of the Si-Pb₃O₄ system. Differential thermal analysis, X-ray diffraction and infra-red spectroscopy have been used to examine the thermal behaviour of the mixture to characterize its combustion products and judge the validity of both proposed reaction paths.It was concluded from the results that the Si-Pb₃O₄ system exhibits rather complicated reaction mechanism including both gas-solid and solid-solid (proceeding below oxidant decomposition temperature) reactions whose importance depends on the fuel content of the mixture.     

Improvement of Structural and Thermal Stabilities of PVC and Wood/PVC Composite by Zn and Pb Stearates,and Zeolite

Three different chemical stabilizers were introduced into neat PVC and a wood/PVC composite (containing 50 phr wood flour) to improve their thermal and structural stabilities. The changes in CIE yellowness index, polyene index, %wt loss, and decomposition temperature (T_d) were monitored. The effects of type and content of thermal stabilizers, thermal ageing time, and the presence of wood flour were our main interests. The experimental results suggested that the additions of Zn and Pb stearates into PVC and wood/PVC composite could improve the thermal stability of the PVC. At the test temperature of 177°C, the additions of Zn and Pb stearates could improve the thermal stabilities of PVC by retarding the upzipped reaction and by reducing the conjugated double bonds in PVC, Pb stearate being the most suitable for thermally stabilizing the PVC. Around the T_d range (～264°C), the addition of Zn stearate reduced the T_d value of PVC whereas that of Pb stearate had no effect on the change in T_d value. Zeolite loading could shift the T_d value of the PVC from 264 to 280°C. The addition of wood particles increased the polyene content and decreased the decomposition temperature of the PVC. The effect of wood flour on the thermal and structural changes of PVC overruled that of thermal stabilizer loading.     

Effect of Solvent (Plasticizers) on PVC Degradation

Both plasticized (semi-rigid and flexible) PVC materials as well as PVC in solutions, the rate of their thermal degradation and effective stabilization are caused by essentially different fundamental phenomena in comparison to aging of PVC in absence of the solvent. Both structure and macromolecular dynamics render the significant influence on its stability, i.e. chemical nature of the solvent (plasticizer), its basicity, specific and non-specific solvation, degree of PVC in a solution (solubility), segmental mobility of macromolecules, thermodynamic properties of the solvent (plasticizer), formation of associates, aggregates, etc. The chemical stabilization of PVC plays a less significant role. The effect of above factors on stability (behavior) of semi-rigid and flexible PVC will be done on quantitative level. It will be described effect of “echo”-type of stabilization on the stability of PVC in the presence of plasticizers. If we would like to have stable material from PVC we should make stabilization of plasticizers as more reactive chemical compounds.     

Solvation dynamics of Hoechst 33258 in water: an equilibrium and nonequilibrium molecular dynamics study

Integrated within an appropriate theoretical framework, molecular dynamics (MD) simulations are a powerful tool to complement experimental studies of solvation dynamics. Together, experiment, theory, and simulation have provided substantial insight into the dynamic behavior of polar solvents. MD investigations of solvation dynamics are especially valuable when applied to the heterogeneous environments found in biological systems, where the calculated response of the environment to the electrostatic perturbation of the probe molecule can easily be decomposed by component (e.g., aqueous solvent, biomolecule, ions), greatly aiding the molecular-level interpretation of experiments. A comprehensive equilibrium and nonequilibrium MD study of the solvation dynamics of the fluorescent dye Hoechst 33258 (H33258) in aqueous solution is presented. Many fluorescent probes employed in experimental studies of solvation dynamics in biological systems, such as the DNA minor groove binder H33258, have inherently more conformational flexibility than prototypical fused-ring chromophores. The role of solute flexibility was investigated by developing a fully flexible force-field for the H33258 molecule and by simulating its solvation response. While the timescales for the total solvation response calculated using both rigid (0.16 and 1.3 ps) and flexible (0.17 and 1.4 ps) models of the probe closely matched the experimentally measured solvation response (0.2 and 1.2 ps), there were subtle differences in the response profiles, including the presence of significant oscillations for the flexible probe. A decomposition of the total response of the flexible probe revealed that the aqueous solvent was responsible for the overall decay, while the oscillations result from fluctuations in the electrostatic terms in the solute intramolecular potential energy. A comparison of equilibrium and nonequilibrium approaches for the calculation of the solvation response confirmed that the solvation dynamics of H33258 in water is well-described by linear response theory for both rigid and flexible models of the probe.     

Thermal degradation and evolved gas analysis of thiourea-formaldehyde resin (TFR) during pyrolysis and combustion

Thiourea formaldehyde resin (TFR) has been synthesized by condensation of thiourea and formaldehyde in acidic medium and its thermal degradation has been investigated using TG-FTIR-MS technique during pyrolysis and combustion. The results revealed that the thermal decomposition of TFR occurs in three steps assigned to drying of the sample, fast thermal decomposition of polymers, and further cracking. The similar TG and DTG characteristics were found for the first two stages during pyrolysis and combustion. The combustion process was almost finished at 680?°C, while during pyrolysis a total mass loss of 93 wt% is found at 950?°C. The release of volatile products during pyrolysis are NH₃, CS₂, CO, HCN, HNCS, and NH₂CN. The main products in the second stage are NH₃ CO₂, CS₂, SO₂, and H₂O during combustion. In the next stage, the combustion products mentioned above keep on increasing, but some new volatiles such as HCN, COS etc., are identified. Among the above volatiles, CO₂ is the dominant gaseous product in the whole combustion process. It is found that the thermal degradation during pyrolysis of TFR produced more hazardous gases like HCN, NH₃, and CO when compared with combustion in similar conditions.     

Investigations on poly(vinyl chloride). III. Effects of metal oxides upon thermal decomposition of poly(vinyl chloride)

Thermal decomposition mechanisms of poly(vinyl chloride) (PVC) and the effects of a few metal oxides on the pyrolysis of PVC were previously reported. In the present work, 33 metal oxides were investigated to determine their effects on the thermal decomposition of PVC, by using a pyrolysis gas chromatograph. Most acidic oxides accelerate the recombination of chlorine atoms with double bonds, since PVC containing these metal oxides easily release lower aliphatics, toluene, ethylbenzene, o-xylene, and chlorobenzenes. On the other hand, most basic metal oxides, such as oxides of alkaline earths or silver, inhibit the recombination. These tendencies observed in the thermal decomposition of PVC agree with the contributions of corresponding metal salts to the dehydrochlorination of PVC proposed by other workers. This means that thermal decomposition or dehydrochlorination of PVC is affected by irregularities in head-to-tail linkages formed by the recombination of chlorine atoms during heat treatment of PVC.     

Formation of carbon oxides during tobacco combustion: Pyrolysis studies in the presence of isotopic gases to elucidate reaction sequence

During the combustion of tobacco, carbon monoxide is formed by the thermal decomposition of tobacco with primary products such as carbon dioxide and water. These three processes occur in parallel and are interdependent. The temperature ranges over which each process occurs, and their relative importance have been assessed by pyrolysing tobacco in the presence of various isotopically labelled gases. Non-isothermal pyrolyses were conducted at a heating rate of 1.6 K s^?1 up to 1000°C, with the products analysed by mass spectrometer.Pyrolysis in the presence of oxygen-18 indicates that combustion of tobacco starts at 180°C. Carbon dioxide and water are formed by combustion at 180°C, while carbon monoxide is not formed as a combustion product until 460°C. The quantities of carbon monoxide and dioxide formed by thermal decomposition of tobacco above 400°C are significantly reduced by the occurrence of combustion.Pyrolysis in the presence of carbon-13 dioxide or carbon dioxide-18 shows that its major reaction, endothermic reduction to form carbon monoxide begins at 450°C. Pyrolysis in an oxygen-18/carbon-13 dioxide atmosphere has shown that this endothermic reduction of carbon dioxide occurs in parallel with the strongly exothermic oxidising reactions. 30% of the total carbon monoxide formed was produced by thermal decomposition of the tobacco. 36% was produced by combustion of the tobacco, and at least 23% was produced via carbon dioxide. The remainder was produced by an interaction of the carbon dioxide reduction and the oxidation. Similar proportion would be expected inside the reaction zone of a burning cigarette.Pyrolysis in the presence of heavy water has shown that the major reaction of the water is to quantitatively produce carbon monoxide and hydrogen above 600°C. Considerable isotopic exchange reactions also occur. Pyrolysis in the presence of carbon monoxide-18 has shown that carbon monoxide reacts with tobacco to a small extent at temperatures above 220°C mainly to abstract oxygen combined in the tobacco and produce carbon dioxide.A sequence of general chemical steps for the production of the carbon oxides and water during tobacco combustion has been deduced. This is based on the present work together with considerations of previously published studies on graphite and coal reactions.     

Thermal degradation studies in poly(vinyl chloride)/poly(methyl methacrylate) blends

The miscibility, morphology, and thermal properties of poly(vinyl chloride) (PVC) blends with different concentrations of poly(methyl methacylate) (PMMA) have been studied. The interaction between the phases was studied by FTIR and by measuring the glass transition temperature (T_g) of the blends using differential scanning calorimetry. Distribution of the phases at different compositions was studied through scanning electron microscopy. The FTIR and SEM results show little interaction and gross phase separation. The thermogravimetric studies on these blends were carried out under inert atmosphere from ambient to 800 °C at different heating rates varying from 2.5 to 20 °C/min. The thermal decomposition temperatures of the first and second stage of degradation in PVC in the presence of PMMA were higher than the pure. The stabilization effect on PVC was found most significant with 10 wt% PMMA content in the PVC matrix. These results agree with the isothermal degradation studies using dehydrochlorination and UV-vis spectroscopic results carried out on these blends. Using multiple heating rate kinetics the activation energies of the degradation process in PVC and its blends have been reported.     

酒石酸铅锆的制备、表征及其燃烧催化作用

以酒石酸、硝酸氧锆和硝酸铅为原料,合成出了双金属盐酒石酸铅锆,采用有机元素分析、X射线荧光光谱和FTIR对其进行了表征。在程序升温条件下,利用TG/DTG、DSC、固相原位反应池/FTIR联用技术,研究了酒石酸铅锆的热行为和热分解机理,描述了酒石酸铅锆的热分解过程,分析得出其最终分解产物为ZrO2、PbO和C。利用螺压工艺制备了含酒石酸铅锆的推进剂样品,研究了酒石酸铅锆对双基系推进剂燃烧性能的影响,分析了其燃烧催化作用。结果表明,酒石酸铅锆对双基系推进剂的燃烧具有良好的催化作用,是一种高效的燃烧催化剂;酒石酸铅锆热分解的最终产物PbO是催化燃烧的主要活性物质,推进剂燃烧过程中形成了氧化铅-铅循环催化体系,而锆和碳则起辅助催化的作用。