Grafting Vinyl Monomers onto Nylon 6 Fiber. II. Graft Copolymerization of Methyl Methacrylate onto Nylon 6 Fiber by Photoirradiation in the Presence of Fructose

Photopolymerization of methyl methacrylate (MMA) onto nylon 6 fiber by UV radiation in alcoholic solutions of water-methanol, water-ethanol, and water-n-propanol in the presence of fructose was investigated. The effects of monomer concentration, time of polymerization, fructose concentration, and effect of media have also been studied. Graft add-on (GAO) % greatly enhanced with an increase in monomer concentration and time. With fructose concentration it increases up to 15 mmol/L of fructose and thereafter falls. The GAO in the media is in the following order: W + M + F > W + E + F > W + P + F(W = water; M = methanol; E = ethanol; P = n-propanol). A probable mechanism has been suggested. It appears that the active site is formed on MMA which abstracts an H-atom from the nylon 6 backbone, giving rise to graft of MMA by mutual combination.     

Grafting Vinyl Monomers onto Nylon 6 Fiber. III. Graft Copolymerization of Vinyl Monomers onto Nylon 6 Fiber in Water Medium in the Presence of Fructose

Nylon 6 fiber was grafted with various vinyl monomers e.g., methyl methacrylate (MMA), ethyl methacrylate (EMA), and n-butyl methacrylate (n-BMA), in water in the presence of fructose using a carbon arc lamp as the source of photoirradiation at 70°C and a liquor ratio of 1:26. The effects of various parameters, e.g., monomer concentration, time of grafting, and fructose concentration on grafting reactions, were studied individually for each monomer. The graft yield is greatly enhanced by increasing the monomer concentration and the time of grafting. However, the optimum fructose concentration is required for maximum grafting efficiency. The accelerating action of photopolymerization by fructose was attributed to the sensitizing action of fructose involving an energy transfer.     

Grafting vinyl monomers onto wool fibers. III. Graft copolymerization of methyl methacrylate onto wool using hexavalent chromium ion

The use of hexavalent chromium to initiate graft copolymerization of methyl methacrylate onto wool fibers has been investigated. The rate of grafting was determined by varying monomer, chromium(VI), temperature, acidity of the medium, nature of wool, reaction medium, and redox system. The graft yield increases with increasing monomer concentration up to 0.65M, and, with further increase of monomer the graft yield decreases. The graft yield increases with increasing chromium(VI) concentration. The grafting is considerably influenced by chemical modification of wool prior to grafting. The effect of certain inorganic salt and anionic surfactant on the rate of grafting has been investigated. The graft yield is influenced by thiourea concentration; it decreases with increasing thiourea concentration.     

Evaluation of surface composition of surface active water-alcohol type mixtures: a comparison of semiempirical models

We study adsorption at planar liquid-vapor interface of surface active binary mixtures and test three well-known models for the composition of surface phase. The models were originally presented by Guggenheim. These are compared to results for model fluids from density functional theory (DFT). The model of Laaksonen and Kulmala is in best agreement with DFT calculations. Surface mole fraction of the solute component from the Guggenheim model exceeds one for a mixture with high surface activity. The failure of the Guggenheim model is also evident in our calculations for water-methanol, water-ethanol, and water-n-propanol mixtures.     

Grafting Vinyl Monomers onto Silk Fibers. V. Graft Copolymerization of Methyl Methacrylate onto Silk with Potassium Permanganate as Initiator

The graft copolymerization of methyl methacrylate onto silk fibers in aqueous solution with the use of manganese (IV) ions as initiator was investigated. The rate of grafting was determined by varying monomer, acidity of the medium, temperature, nature of silk, and the reaction medium. The graft yield increases significantly with increase of manganese (IV) concentration up to 15 meq/liter; with further increase of manganese (IV) concentration, the graft yield decreases. The effect of the increase of monomer concentration brings about a significant enhancement in the graft yield up to 7%, and with further increase of monomer concentration the graft yield decreases. The graft yield is considerably influenced by chemical modification prior to grafting. The effect of some inorganic salts and anionic surfactants on the rate of grafting has been investigated.     

Grafting vinyl monomers onto silk fibers. IX. Graft copolymerization of methyl methacrylate onto silk using peroxydiphosphate-thiourea redox system

The graft copolymerization of methyl methacrylate (MMA) onto silk in aqueous media initiated by the potassium peroxydiphosphate-thiourea redox system was studied at 50°C. The rate of grafting was determined by changing [monomerl], [thiourea], [initiator], acidity of the medium, reaction medium, and temperature. A significant increase percent of grafting was noticed with increasing monomer concentration to 84.49 × 10^?2 mole/liter and the further increase is associated with the decrease of graft yield. The graft yield increases with an increase of thiourea (Tu) concentration to 25 × 10^?5 mole/liter; then it decreases. A measurable increase in graft yield was observed with an increase in acidity of the medium. Graft yield increases to a certain temperature, i.e., 50°C, and then it decreases. The graft yield increases with an increase of initiator concentration to 60 × 10^?4 mole/liter; then it decreases. The graft yield is medium dependent. A suitable kinetic path has been proposed and the rate equation has been derived.     

Graft Copolymerization of Methyl Methacrylate onto Nylon 6 Using Thallium(III) Ions as Initiator

Abstract

Graft copolymerization of methyl methacrylate onto nylon 6 was investigated in aqueous perchloric acid medium using thallium(III) ions as initiator. The rate of grafting was evaluated by varying the concentrations of monomer, initiator, acid, and temperature. The rate of grafting was found to increase with an increase of both monomer and initiator concentrations. The graft yield was found to increase with an increase in the acid concentration up to 0.49 mL^?1, and beyond this concentration of perchloric acid the graft yield was found to decrease. It also increased with an increase of temperature. From the Arrhenius plot the overall activation energy was found to be 3.9 kcal/mol. The effects of inhibitors, various solvents, inorganic salts, and swelling agents on graft yield were studied. A suitable kinetic scheme has been proposed and a rate equation has been derived.     

Grafting Vinyl Monomers onto Wool Fibers. VII. Graft Copolymerization of Methyl Methacrylate onto Wool Using Peroxydiphosphate-Thiourea Redox System

Graft copolymerization of methyl methacrylate onto wool was investigated in aqueous solution using the potassium peroxy-diphosphate-thiourea redox system as the initiator. The rate of grafting was determined by varying the monomer, peroxydi-phosphate ion, temperature, and solvent. The graft yield increases with increasing peroxydiphosphate ion up to 80 × 10^?-⁴ mol/L, and with further increase of peroxydiphosphate ion the graft yield decreases. The graft yield increases with increasing monomer concentration. The percentage of grafting decreases with increasing thiourea concentration. The rate of grafting increases with an increase of temperature. The effect of acid and water-soluble solvent and certain salts on graft yield has been investigated and a suitable rate expression has been derived.     

Grafting onto Wool. XXVI. Graft Copolymerization of Vinyl Monomers by Use of Cr(acac)3-TBHP as Initiator

Methyl methacrylate (MMA), methyl acrylate (MA), and ethyl acrylate (EA) have been graft copolymerized onto wool fiber in aqueous medium using the chromium acetylacetonate-tertiary-butyl hydroperoxide (Cr(acac)₃-TBHP) system as initiator. The percentage of grafting has been determined as a function of the concentrations of monomer, chelate, and TBHP, and the time and temperature under optimum conditions. MMA produced a maximum grafting of 119.8%, MA produced a maximum grafting of 56%, while EA afforded maximum grafting to the extent of 41.9%. Different vinyl monomers were found to follow the following reactivity order toward grafting onto wool fiber in the presence of the Cr(acac)₃-TBHP system: MMA > MA > EA.     

Radiation-induced graft polymerization of acrylic acid onto fluorinated polymers. I. Kinetic study on the grafting onto poly(tetrafluoroethylene-ethylene) copolymer

Direct radiation-induced grafting of aqueous acrylic acid (AAc) onto poly(tetrafluoroethylene-ethylene) (ET) film has been studied. The effect of grafting conditions such as monomer concentration, exposure dose, dose rate, and film thickness on the grafting yield was investigated. The dependence of the grafting rate on monomer concentration was found to be 1.2 order. The dependence of the grafting rate on dose rate was found to be 0.6 order regardless of the film thickness. The relationship between the grafting rate and film thickness gave a negative first-order dependence. The results suggest that the grafting process is mainly controlled by monomer diffusion, and it was concluded that this grafting system proceeded by the front mechanism. The swelling behavior increases linearly with degree of grafting. The electrical conductivity and mechanical properties for the trunk and grafted polymer were investigated at different irradiation doses in air and under vacuum irradiations. © 1992 John Wiley & Sons, Inc.     

Graft copolymerization onto rubber. V. Graft copolymerization of methyl methacrylate onto rubber using potassium peroxydiphosphate as initiator

The graft copolymerization of methyl methacrylate onto natural rubber (NR) is investigated using potassium peroxydiphosphate as the initiator. The rate of grafting is determined by varying monomer concentration, peroxydiphosphate concentration, and temperature. The graft yield increased with an increase in monomer concentration up to 1.4082M/L and thereafter the graft yield decreases. The graft yield increases significantly with an increase of peroxydiphosphate concentration up to 150 X 10^-1M/L and thereafter the graft yield decreases. The grafting reaction is temperature dependent. A suitable kinetic scheme is proposed and the rate equation is evaluated.     

Kinetic effects of alcohol addition on the anodic behavior of silicon in acid fluoride media

The anodic dissolution of silicon in acid solutions of ammonium fluoride is investigated in aqueous and water-alcohol media by rotating disk voltammetry and impedance spectroscopy. The voltammograms recorded in water-alcohol media show, in comparison to water, the following effects: an increase of the dissolution currents measured at pH>2 and an opposite effect at pH<2; a distortion of the curve, with a relative increase of the characteristic currents in the region of low applied potentials, indicating easier dissolution of the "wet" oxide forming under those conditions; a shift of the maximum of the current-pH curves from about pH 3 in water to about pH 4 in 50% ethanol v/v. Analysis of impedance data at pH values 4-5 in water and water-ethanol media show similar dependence on potential for the parameters Chf (high-frequency capacitance) and RhfI (Rhf is a high-frequency resistance and I is the steady state current), suggesting the formation of oxide films with similar properties. The marked differences of anodic behavior in the two types of media are discussed and explained in terms of the effects of alcohol addition on the speciation equilibria of hydrofluoric acid and on the kinetic rate constants of dissolution of the surface oxide layer.     

Grafting onto wool. XXV. Effect of acids on γ-radiation-induced graft copolymerization of methyl methacrylate onto wool fiber

Graft copolymerization of methyl methacrylate (MMA) onto Himachali wool fiber has been investigated in aqueous medium by using γ irradiation from a 2100 Ci⁶⁰CO source as means of initiation. Graft copolymerization was carried out by the mutual method in nitrogen atmosphere as well as in air. Effect of mineral acids and acetic acid on percentage of grafting was studied. Percentage of grafting was determined as functions of total dose, concentration of monomer, and concentration of acids. Maximum percentage of grafting in the presence of acids occurred in nitrogen atmosphere at a total dose of 1.05 MR. All the acids were found to influence grafting and the reactivity of different acids towards graft copolymerization was found to follow the order: H₂SO₄ > HCl > HNO₃ > HC1O₄ > HOAc. An attempt has been made to explain the reactivity order of different acids in the light of the mechanism proposed for γ-irradiation-induced graft copolymerization of vinyl monomer onto wool fiber.     

Grafting onto Wool. XV. Graft Copolymerization of MA and MM A by Use of Mn(acac)3 as Initiator

Graft copolymerization of acceptor monomers MA and MMA onto Himachali wool fiber in an aqueous medium was studied by using Mn(acac)s as initiator. Nitric acid was found to catalyze the graft copolymerization. Percentage of grafting and percent efficiency have been determined as functions of the concentration of chelate, nitric acid, monomer, time, and temperature, Under optimum conditions, MMA produced a maximum grafting of 82.5% while MA afforded maximum grafting to the extent of 27.5%. Relative reactivities of MA and MMA toward grafting have been compared with those of EA, BA, and VAc reported earlier from this laboratory. Different vinyl monomers were found to follow the following reactivity order toward grafting onto wool fiber in the presence of Mn(acac)₃: MMA > EA > BA > MA > VAc. An attempt has been made to explain the observed reactivity pattern shown by different vinyl monomers in graft copolymerization reactions.     

Synthesis of perfluorinated cation exchange membranes by preirradiation grafting of acrylic acid onto ethylene-tetrafluoroethylene films

Hydrophilic carboxyl-containing fluoromembranes were obtained by preirradiation grafting of acrylic acid onto ethylene-tetrafluoroethylene film. The dependence of the grafting reaction on temperature, monomer concentration, nature and concentration of inhibitor, crosslinking agent, solvent, and on the preirradiation dose was investigated. The grafting rates increase with temperature, whereas the saturation degree of grafting (SDG) decreases. Addition of inhibitor minimizes homopolymerization and at the same time hinders the grafting reaction. The SDG increases markedly with monomer concentration until it reaches a maximum and thereafter decreases. The grafting rates increase with preirradiation dose. Addition of crosslinking agent initially decreases the SDG, and thereafter increases. The highest grafting rates are obtained using water as solvent followed by methanol and ethanol. The results are discussed on the basis of various parameters: interaction between monomer diffusibility and the viscosity of the monomer bath, the mutual reactivity of monomer, and the crosslinking agent. An agreement is observed between the values of the electrical resistance and the saturation degree of grafting. © 1996 John Wiley & Sons, Inc.     

Grafting Vinyl Monomers onto Tussah Silk Fiber. I. Graft Copolymerization of Methyl Methacrylate onto Nonmulberry Tussah Silk by Tetravalent Cerium Ion

The graft copolymerization of methyl methacrylate onto nonmulberry natural tussah silk fibers was investigated in aqueous solution using tetravalent cerium as initiator. The rate of grafting was determined by varying the monomer concentration, the cerium (IV) concentration, the temperature, and the nature of the silk. With increasing monomer concentration the graft yield increased (up to 0.657 M) and thereafter decreased. The graft yield also increased with increasing cerium (IV) concentration. The graft-on was influenced by chemical modification of the tussah silk prior to grafting. The effect of certain inorganic salts on the rate of grafting was investigated.     

Synthesis and characterization of graft copolymers of methacrylonitrile/methacrylate mixtures onto amylomaize by the ceric ion method

Graft polymerizations of mixtures of methacrylonitrile with n-alkyl methacrylales onto amylomaize were carried out. The graft copolymers were characterized by both IR and ¹³C-NMR spectroscopies. The influence of the monomer feed on the grafting parameters has been studied. The variation of these parameters with the mole fraction of methacrylate in the feed for the first three systems studied, MAN/MMA, MAN/EMA and MAN/BMA, was similar: thus, percent grafting (%G, percent weight of grafted polymer with respect to grafted amylomaize), percent grafted amylomaize (%GA, percent weight of grafted amylomaize with respect to initial amylomaize), percent grafting conversion (%C_g, percent weight of grafted polymer with respect to initial monomer), and percent total conversion (%C_t, percent weight of total acrylic polymer with respect to initial monomer) were increased, but percent grafting efficiency (%GE, percent weight of graft copolymer with respect to total polymer) decreased. The system MAN/HMA presented values of grafting parameters lower than those of the previous systems. The optimum values were obtained at 0.6 HMA mole fraction in the monomer feed. When the number of carbon atoms of the n-alkyl group rises from 1 to 4, the increase of the n-alkyl group length gives rise to increases of the %G %C_g and %C_t values and decreases of the %GE and %GA values. For the largest methacrylate, the grafting reaction appears to be controlled by the lesser accessibility of the monomer to the active sites of the carbohydrate. © 1992 John Wiley & Sons, Inc.     

Membranes obtained by preirradiation grafting of acrylic acid onto poly(tetrafluoroethylene–perfluorovinyl ether)

Some properties of the membranes obtained by preirradiation grafting of acrylic acid onto poly(tetrafluoroethylene-perfluorovinyl ether) copolymer (PFA) films have been investigated. The dimensional change caused by grafting and swelling behavior, water uptake, electrical conductivity, and mechanical properties of the grafted films were found to increase as the grafting proceeds. The influence of the preparation conditions (such as preirradiation dose, monomer concentration, grafting temperature, and film thickness) on those properties was studied. These properties were found to be dependent mainly on the degree of grafting regardless of grafting conditions, except at higher monomer concentration (>40 wt %). The electric conductivity and mechanical properties for the membranes obtained at higher AAc concentrations were lower than those obtained at lower ones. Analysis by x-ray microscopy of the grafted films revealed that the grafting begins at the part close to the film surface and proceeds into the central part with progressive diffusion of monomer to give finally homogeneous distribution of the electrolytes in the whole bulk of the polymer. The membranes show good electrochemical and mechanical properties which make them acceptable for practical use as cation-exchange membranes.     

Radiation-induced grafting of styrene onto ultra-high molecular weight polyethylene powder and subsequent film fabrication for application as polymer electrolyte membranes: I. Influence of grafting conditions

Ultra-high molecular weight polyethylene (UHMWPE) powder was irradiated by gamma rays using a ⁶⁰Co source. Simultaneous and pre-irradiation grafting was performed in air and in inert atmosphere at room temperature. The monomer selected for grafting was styrene, since the styrene-grafted UHMWPE could be readily post-sulfonated to afford proton exchange membranes (PEMs). The effect of absorbed radiation dose and monomer concentration in methanol on the degree of grafting (DG) is discussed. It was found that the DG increases linearly with increase in the absorbed dose, grafting time and monomer concentration, reaching a maximum at a certain level. The order of rate dependence of grafting on monomer concentration was found to be 2.32. Furthermore, the apparent activation energy, calculated by plotting the Arrhenius curve, was 11.5 kJ/mole. Lower activation energy and high rate dependence on monomer concentration shows the facilitation of grafting onto powder substrate compared with film. The particle size of UHMWPE powder was measured before and after grafting and found to increase linearly with increase in level of grafting. FTIR-ATR analysis confirmed the styrene grafting. The grafted UHMWPE powder was then fabricated into film and post-sulfonated using chlorosulfonic acid for the purposes of evaluating the products as inexpensive PEM materials for fuel cells. The relationship of DG with degree of substitution (DS) of styrene per UHMWPE repeat unit and ion exchange capacity (IEC) is also presented.     

Grafting Vinyl Monomers onto Wool Fibers. X. Graft Copolymerization of Methyl Methacrylate onto Wool Using Acetylacetonato Complex of Manganese(lII)

The graft copolymerization of methyl methacrylate onto wool fibers was investigated in aqueous solution using the acetylacetonato complex of manganese(III). The rate of grafting was determined by varying the monomer, the complex, the temperature, the acidity of the medium, the nature of the wool, and the reaction medium. The graft yield increases with increasing monomer and complex concentrations. The graft yield also increases with increasing temperature. The grafting is considerably influenced by chemical modification of wool prior to grafting. A suitable mechanism has been proposed and a rate equation has been derived.