含氮、硫单体等离子体聚合过程中气相组分分析

报导了用ＧＣ－ＭＳ和ＩＲ对含氮，硫单体等离子体聚合过程中气相组分的分析，根据分析结果探讨了该类单体等离子体聚合机理。     

Plasma Induced Graft Polymerization of Three Hydrophilic Monomers on Nylon 6,6 Fabrics for Enhancing Antistatic Property

In this study, three hydrophilic monomers; 2-acrylamido-2-methyl-1-propanesulfonic acid, 2-hydroxyethyl methacrylate, diallyldimethylammonium chloride (DADMAC) were selected and their performance as an antistatic finish on nylon 6,6 fabrics was investigated. A non-thermal, high density atmospheric pressure plasma was used to graft polymerize the monomers on nylon 6,6 fabrics. Fabrics were first treated with solutions of monomer in water, air dried and then treated with helium plasma to graft polymerize the monomer on the fiber surface. Surface resistivity values were measured before and after soxhlet extraction with water. Results showed that the DADMAC monomer provided better antistatic properties to fabrics. Further studies with DADMAC monomer were made; effects of plasma post exposure time, plasma pre-exposure time, plasma power, concentration of the monomer and existence of a crosslinker were investigated. Higher plasma power, higher concentration of the monomer and longer post exposure times all gave better antistatic properties to the nylon 6,6 fabrics. Acid dye staining, UV–Vis and FT-IR measurements were conducted and results confirmed a grafted poly-DADMAC layer on the fabric surface.     

玻璃纤维表面的乙烯基单体接枝聚合

用玻璃纤维表面处理剂ＭＡＣ处理玻璃纤维后，再进行臭氧处理，使玻璃纤维的表面产生活性中心，引发苯乙烯、甲基丙烯酸甲酯、及丙烯酸等乙烯基单体在玻璃纤维表面上接枝聚合。接枝纤维的密度减小，对水的浸润性下降，红外光谱及扫描电镜观察证明玻璃纤维表面上接枝聚合物的存在。     

Gamma-Ray Induced Polymerization of Vinyl Monomers in Bagasse

Vinyl monomers such as vinyl acetate, vinyl chloride, methyl methacrylate and styrene etc., can be polymerized without catalyst into the composites of bagasse material by gamma-radiation induced in situ liquid polymerization process. The fundamental factors, such as polymerization-rate, effect of swelling agent, molecular weight of vinyl polymers and graft reaction between bagasse cellulose and vinyl polymers, have been investigated and discussed. The use of suitable low G-value polar swelling agents and the application of suitable gamma dose-rate are two key factors found to control the smooth in situ liquid polymerization system of vinyl monomers in bagasse.     

Grafting Vinyl Monomers onto Wool Fibers: Graft Copolymerization of Methyl Methacrylate onto Wool Using Ferric Acetylacetonate Complex

The graft copolymerization of methyl methacrylate (MMA) onto native and reduced Indian Chokla wool fibers was studied in aqueous solution using an acetylacetonate complex of Fe(III). Perchloric acid was found to catalyze the reaction. The rate of grafting was investigated by varying the concentration of the monomer and the complex, the acidity of the medium, and the solvent composition of the reaction medium. The graft yield increases with increasing concentration of the initiator and with increasing temperature. An increase of monomer concentration up to 0.5634 mol/L and of the HClO4 concentration up to 0.01 mol/L increases the graft yield. Reduced and oxidized wools were found to be better substrates than untreated, esterified, cross-linked, and trinitrophenylated wools. Among the various monomers studied, MMA was found to be the most active. A suitable kinetic scheme is proposed. From the activation energy data, average molecular weight, and spectral studies, the reactivity of -SH groups, and the extent of chain transfer is ascertained.     

Study on Generation of Glow Discharge Plasma in Air and Surface Modification of Wool Fabric

Plasma Chemistry and Plasma Processing - A lamellar electrode structure is proposed to achieve the generation of a large-area plasma and the effective processing of the wool fabric with the...     

氧化镁表面辐射接枝聚合反应机理研究

氧化镁表面辐射接枝聚合反应机理研究蒋波＊黄光琳（四川联合大学原子核科学技术研究所成都６１００６４）（四川联合大学化学系成都）关键词氧化镁，反应机理，辐射接枝，甲基丙烯酸甲酯１９９６－０５－２１收稿，１９９６－０８－２６修回辐射诱发有机单体在固体表面聚...     

Aqueous Diphenyl Degradation Induced by Plasma with Glow Discharge Electrolysis

The degradation of aqueous phase diphenyl induced by plasma that was locally generated between an electrolytic solution and an anode tip is investigated. Results indicated that the degradation rate can be greatly increased by increasing the applied voltage. Faster removal rate can be achieved for a relatively higher alkalinity or acidity. Fe²⁺ has an evident catalytic effect on the diphenyl elimination, while the presence of n‐butanol inhibited the degradation. The major intermediate products of the degradation process were identified by HPLC analysis and a degradation pathway was proposed.     

Grafting Vinyl Monomers onto Wool Fibers. VII. Graft Copolymerization of Methyl Methacrylate onto Wool Using Peroxydiphosphate-Thiourea Redox System

Graft copolymerization of methyl methacrylate onto wool was investigated in aqueous solution using the potassium peroxy-diphosphate-thiourea redox system as the initiator. The rate of grafting was determined by varying the monomer, peroxydi-phosphate ion, temperature, and solvent. The graft yield increases with increasing peroxydiphosphate ion up to 80 × 10^?-⁴ mol/L, and with further increase of peroxydiphosphate ion the graft yield decreases. The graft yield increases with increasing monomer concentration. The percentage of grafting decreases with increasing thiourea concentration. The rate of grafting increases with an increase of temperature. The effect of acid and water-soluble solvent and certain salts on graft yield has been investigated and a suitable rate expression has been derived.     

Radical Graft Polymerization of Vinyl Monomers Initiated by A20 Groups Introduced Onto a Carbon Black Surface: Effect of azo Groups on Graft Polymerization

The radical graft polymerization of vinyl monomers from carbon black initiated by azo groups introduced onto the surface was investigated. The introduction of azo groups onto carbon black surface was achieved by three methods: the reaction of 2,2′-azobis[2-(2-imidazolin-2-yl)propane] (AIP) with (1) epoxide groups, which were introduced by the reaction of carbon black with chlorometh-yloxirane; (2) acyl chloride groups, which were introduced by the reaction of carboxyl groups on the surface with thionyl chloride; and (3) 3-chloroformyl-1-cyano-1-methylpropyl groups, which were introduced by the reaction of carbon black with 4,4′-azobis(4-cyanovaleric acid) and then thionyl chloride. The amount of azo groups introduced onto the surface by the above methods was determined to be 0.07-0.19 mmol/g. The graft polymerization of methyl methacrylate was found to be initiated by azo groups introduced onto the carbon black surface. During the polymerization, poly(methyl methacrylate) was effectively grafted onto carbon black through propagation of the polymer from the radical produced on the surface by the decomposition of the azo groups. The percentage of grafting using carbon black having azo groups introduced by method 1 increased to 40%. It was also found that the graft polymerization of several vinyl monomers such as styrene, acrylonitrile, and acrylic acid was initiated by the azo groups introduced onto the surface and the corresponding polymer was effectively grafted onto the surface. Furthermore, the effect of the amount of carbon black having azo groups on the graft polymerization was investigated.     

Anode Magnetron Enhanced DC Glow Discharge Processes for Plasma Surface Cleaning and Polymerization

The objective of this study was to examine some fundamental factors involved in the design and construction of the anode magnetron dc glow discharge processes as well as its performance in plasma cleaning and polymerization. Those advantages of anode magnetron include the capability of the magnetron to operate at low pressure, as well as decreasing the thickness of cathode dark space, i.e., the negative glow which contains a higher concentration of ions and active species was more closely to the cathode surface, which makes the plasma surface cleaning and polymerization an effective and uniform processes. The deposition rate at a given discharge power is increased by the presence of anode magnetrons, and is also much higher relative to rf and af. The refractive index of dc plasma film at a given polymer thickness (such as TMS, 70 nm, RI: 2.4) is higher than rf, af, and cascade arc plasma (RI: 1.6–1.7).     

Efficient Degradation of Nitrobenzene Induced by Glow Discharge Plasma in Aqueous Solution

The oxidative degradation of nitrobenzene (NB) induced by gaseous glow discharge plasma in contact with aqueous solution was investigated. The experimental results indicated that NB removal obeyed first-order kinetics under certain applied currents. The major degradation byproducts such as nitrophenols, phenol, 1,3-dinitrobenzene and carboxylic acids have been detected. The distribution of nitrophenols follows the order o- > p- > m- and oxalic, formic and acetic acids are major carboxylic intermediates. The eventual products were nitrate ion and carbon dioxide. During the treatment, a large amount of hydrogen peroxide was produced. Addition of ferrous or ferric ions into the solution greatly enhanced the degradation rate due to Fenton’s reaction. The energy efficiencies of NB removal and hydrogen peroxide formation were compared with those of other discharges. Hydroxyl radicals were shown to be the most likely species responsible for NB degradation     

Gamma Ray Induced Gaseous Phase Polymerization and Copolymerization of Vinyl Monomers in Bagasse

Gamma-ray induced gaseous phase in situ polymerization of vinyl chloride and copolymerization of vinyl chloride with vinyl acetate in bagasse have been investigated and discussed. The prepared bagasse-plastic combinations were not improved of its mechanical strength owing to the deposited PVC powder and the low copolymer loading in bagasse-board. The viscosity average molecular weight of PVC formed in bagasse-board was found to be slightly higher than that of PVC formed in the in situ liquid polymerization system. No graft reaction of PVC onto bagasse cellulose was observed, while low grade of graft reaction was confirmed with PVC-PVAc copolymer system.     

Glow Discharge Plasma Induced Dechlorination and Decomposition of Dichloromethane in an Aqueous Solution

In the present study, efficient dechlorination and decomposition of dichloromethane (DCM) induced by glow discharge plasma (GDP) in contact with an aqueous solution was investigated. Experimental results showed that DCM underwent effective dechlorination and decomposition under the action of GDP. Both the removal and the dechlorination of DCM increased with increasing pH and with the presence of hydroxyl radical scavengers and decreased with quenchers of hydrated electrons. Formic acid and formaldehyde were the major intermediate byproducts. Final products were carbon dioxide and chloride ion. Hydrated electrons were the most important active species responsible for initiation of the reaction. Hydrolysis of the resulting chloromethyl radicals played an important role in mineralization of chlorine atoms of the molecule. Hydroxyl radicals were mainly involved in the oxidation of the intermediate byproducts. Reaction mechanism was proposed based on the dechlorination kinetics and the distribution of intermediate byproducts.     

Grafting Vinyl Monomers onto Wool Fibers. X. Graft Copolymerization of Methyl Methacrylate onto Wool Using Acetylacetonato Complex of Manganese(lII)

The graft copolymerization of methyl methacrylate onto wool fibers was investigated in aqueous solution using the acetylacetonato complex of manganese(III). The rate of grafting was determined by varying the monomer, the complex, the temperature, the acidity of the medium, the nature of the wool, and the reaction medium. The graft yield increases with increasing monomer and complex concentrations. The graft yield also increases with increasing temperature. The grafting is considerably influenced by chemical modification of wool prior to grafting. A suitable mechanism has been proposed and a rate equation has been derived.     

Grafting onto Wool. IX. Graft Copolymerization of Vinyl Monomers by Use of Vanadium Oxyacetylacetonate as Initiator

Methyl methacrylate (MMA), acrylic acid (AAc), and vinyl acetate (VAc) were graft copolymerized onto Himachali wool in an aqueous medium by using vanadium oxyacetyl acetonate as initiator. Graft copolymerization was studied at 45, 55, 65, and 75°C for various reaction periods. The percentage of grafting was determined as functions of concentration of monomers, concentration of initiator, time, and temperature. The maximum percentage of grafting with each monomer occurred at 55°. Several grafting experiments were carried out in the presence of various additives which include HNO3, DMSO, and pyridine. Nitric acid was found to promote grafting of MMA. All these additives had adverse effects on grafting of VAc and AAc. MMA, VAc, and AAc were found to differ in reactivity toward grafting and followed the order MMA > AAc > VAc.     

Electroinitiated Anionic Polymerization of Vinyl Monomers

Abstract

Polarographic reduction and electrolytically initiated anionic polymerization of various monomers have been investigated with tetra-n-butylammonium perchlorate in dimethoxyethane.     

Photoinitiated Cationic Polymerization of Unconventional Monomers

Photoinitiated cationic polymerization of unconventional monomers namely, benzoxazines, monothiocarbonates and macromonomers of poly(ε-caprolactone) and poly(ethylene oxide) is described. Ring opening polymerization of benzoxazines and thiocarbonates by direct and sensitized photoinitiation using onium salts was studied. The structures of the resulting polybenzoxazine were complex and related to the ring opening process of the protanated monomer either at through oxygen or nitrogen atoms. In the case of monothiocarbonate, the polymerization was accompanied with isomerization of thiocarbonate group. The potential use of macromonomers in photoiniated cationic polymerization to design complex macromolecular structures such as graft copolymers, water-borne photoresist materials and networks with dangling chains was presented. Photoinduced oxidative polymerization of thiophene, precursor for conducting polymers, using onium salts was also demonstrated.     

Ionic Polymerization of Vinyl Aromatic Monomers

The ionic polymerization of vinyl monomers possessing aromatic and heterocyclic functional groups has not been studied in any systematic fashion. Only in a few isolated cases have detailed mechanistic and structural studies been reported. The anionic polymerization of a number of vinylanthracene monomers has recently been investigated and some rationalization of this system is presented. The cationic and anionic polymerization of the N-, 3-, and 2-vinylcarbazole series of monomers is discussed in some detail. The important role of vinyl aromatic/vinyl heterocyclic monomers, i.e., diphenylethylene and the vinylcarbazoles, in elucidating the mechanistic aspects of cationic polymerization, “change transfer” polymerization, and photoionic polymerization is considered.     

Oxidative Degradation of Aqueous Cresols Induced by Gaseous Plasma with Contact Glow Discharge Electrolysis

The oxidative degradation of cresols smoothly proceeded toward inorganic end products when a gaseous plasma generated by means of dc glow discharge was sustained in contact with the surface of aqueous solution containing organic compounds. In order to get mechanistic insight, the monohydroxylation products from each isomeric cresol were closely examined as primary intermediates to reveal that the aromatic hydroxylation preferentially occurred at the position para to the hydroxyl group of each starting material. It was also established that the degradation of cresols strictly followed the first-order rate law. On the basis of the orientational analysis and the kinetical consideration including the effects of Fe ions added on the reaction rate, it was concluded that hydroxyl radical, which might result from the homolytic cleavage of water molecules by the action of plasma, was the most likely reagent responsible for the mineralization of cresols.