高速搅拌对聚氧化乙烯和聚丙烯酰胺相容效应的研究

热力学的理论计算结果以及采用相差显微镜、透射电镜、小角X-射线散射和应力-应变行为等测试方法获得的结果均表明,聚氧化乙烯(PEO)和聚丙烯酰胺(PAM)共混体系相容性差,在高速搅拌下生成的PEO-PAM嵌段共聚物是有效的增容剂,可使PEO/PAM共混体系的微区尺度减小,不均匀程度降低,相区边界层厚度增大,宏观断裂强度增高。     

On the Structure of Poly-(Ethylene Oxide) When Immersed in Water

It can be shown that poly-(ethylene oxide) in its monomeric form, at molecular weights greater than about 1,000, cannot be soluble in water. Nonetheless, in actual practice poly-(ethylene oxide) is widely used for its hydrophilicity and for its unlimited aqueous solubility. The explanation for this apparent contradiction lies in the fact that poly-(ethylene oxide) molecules form a nonionic surfactant of a novel category, with its hydrophilic and hydrophobic chains attached to each other over their entire length so that its hydrophilic ethylene oxide side is exposed to the water interface while the hydrophobic poly-(ethylene) side remains hidden thanks to the formation of micelles.     

氧化石墨烯增容尼龙6/聚苯乙烯共混体系的研究

氧化石墨烯(GO)亲水性的边缘和疏水性的中间片层使其具有两亲特性.利用GO的这种特性,将其加入尼龙6(PA6)/聚苯乙烯(PS)的共混体系,以提高PA6和PS的相容性.通过两步法制备了PA6/PS/GO共混物,研究了GO对PA6/PS共混材料结构形态与力学性能的影响,并对其增容机理进行了探讨.扫描电镜(SEM)结果表明,添加GO后,共混材料的分散相尺寸明显变小,分散更为均匀,少量的GO即可达到良好的增容效果.动态力学性能(DMA)测试进一步证明了GO对PA6/PS共混物具有一定的增容性.理论计算也表明PS/GO共混物和PA6具有更接近的表面自由能和较低的界面自由能.添加GO后共混物材料的拉伸性能和韧性明显提高.GO添加量为0.1 wt％时,共混材料的断裂伸长率较未添加GO的共混材料提高了170％,断裂能也提高了近240％.     

结构改变对聚对苯二甲酸乙二醇酯局域能级性质的影响

用双轴拉伸、热处理和γ射线辐照的方法制备了一系列具有不同平面取向度,不同结晶度和不同分子链长度的PET试样。通过热释电极化温度扫描法分离出对解俘获电流峰贡献的各局域能级峰。平面取向度、结晶度和γ辐照剂量的提高引起局域能级深度增加,结构缺陷种类的增多导致局域能级数增大(由二个增至六个),能级深度分布加宽。     

四羰基钴钾催化环氧乙烷氢酯基化反应性能研究

我们将在四氢呋喃溶剂中用硼氢化法常温常压合成的四羰基钴钾成功应用于催化环氧乙烷(EO)、一氧化碳和甲醇氢酯基化制备3-羟基丙酸甲酯的反应.用红外光谱(液膜法)对其表征,发现在1 899.93 cm-1有一强吸收峰,证实了[Co(CO)4]-的存在;通过考察反应温度、反应压力及反应时间等因素对反应结果的影响,确定在反应温度75℃、压力3.7 MPa、反应时间为10 h较佳的反应条件下环氧乙烷转化率为98.36%,3-羟基丙酸甲酯选择性为87.54%.     

Peroxide-Induced Synthesis of Maleic Anhydride-Grafted Poly(butylene succinate) and Its Compatibilizing Effect on Poly(butylene succinate)/Pistachio Shell Flour Composites

Framing the Circular Bioeconomy, the use of reactive compatibilizers was applied in order to increase the interfacial adhesion and, hence, the physical properties and applications of green composites based on biopolymers and food waste derived lignocellulosic fillers. In this study, poly(butylene succinate) grafted with maleic anhydride (PBS-g-MAH) was successfully synthetized by a reactive melt-mixing process using poly(butylene succinate) (PBS) and maleic anhydride (MAH) that was induced with dicumyl peroxide (DCP) as a radical initiator and based on the formation of macroradicals derived from the hydrogen abstraction of the biopolymer backbone. Then, PBS-g-MAH was used as reactive compatibilizer for PBS filled with different contents of pistachio shell flour (PSF) during melt extrusion. As confirmed by Fourier transform infrared (FTIR), PBS-g-MAH acted as a bridge between the two composite phases since it was readily soluble in PBS and could successfully form new esters by reaction of its multiple MAH groups with the hydroxyl (–OH) groups present in cellulose or lignin of PSF and the end ones in PBS. The resultant compatibilized green composites were, thereafter, shaped by injection molding into 4-mm thick pieces with a wood-like color. Results showed significant increases in the mechanical and thermomechanical rigidity and hardness, meanwhile variations on the thermal stability were negligible. The enhancement observed was related to the good dispersion and the improved filler-matrix interfacial interactions achieved by PBS-g-MAH and also to the PSF nucleating effect that increased the PBS’s crystallinity. Furthermore, water uptake of the pieces progressively increased as a function of the filler content, whereas the disintegration in controlled compost soil was limited due to their large thickness.     

Effect of Alkylaluminum Activators on Ethylene Trimerization Based on 2,5‐DMP/Cr(III)/TCE Catalyst System

Ethylene trimerization toward 1‐hexene catalytic system with 2,5‐dimethylpyrrole (2,5‐DMP)/Cr(III)/alkylaluminum/tetrachloroethane (TCE) was investigated. The effects of various cocatalysts on catalytic activity and product selectivity were discussed. The results showed that triethylaluminum (TEA), trimethylaluminum (TMA), tri‐n‐hexylaluminum (TNHA) and tri‐isobutylaluminum (TIBA) were all effective cocatalysts for ethylene trimerization toward 1‐hexene. 2,5‐DMP/Cr(III)/TEA/TCE catalytic system afforded the best results for ethylene trimerization, while reducing the level of by‐product formation. Some specific interaction modes of alkylaluminum with active Cr species in the catalytic cycle were proposed to explain the effect of cocatalyst on catalytic activity and 1‐hexene selectivity.     

环氧乙烷环氧丙烷共聚醚的研究进展

综述了环氧乙烷环氧丙烷共聚醚的聚合机理聚合工艺及其应用.环氧乙烷环氧丙烷共聚醚的聚合按其催化剂体系的机理可以分为阴离子聚合、阳离子聚合和配位聚合三类,其中阳离子聚合应用较少.在环氧乙烷和环氧丙烷开环聚合生成共聚醚的反应中,不同的反应工艺条件对生成的聚醚有着很大的影响.同样比例的环氧乙烷和环氧丙烷,因聚合反应器设计、反应器种类、起使剂种类催化剂种类与用量温度加料方式端基结构等的不同,所合成的共聚醚会产生不同的结构和性能.环氧乙烷环氧丙烷共聚形成的聚醚可以分为嵌段共聚醚和无规共聚醚两类.其中,嵌段共聚醚可以分为EPE和PEP两类.     

苯乙烯—丙烯酸钠共聚物改性PET结晶行为的研究

本文用DSC和FT-IR方法研究了PET/苯乙烯-丙烯酸钠共聚物共混体系的相溶性、等温结晶动力学、组成、温度等因素对结晶速率、结晶度等结晶行为的影响,并初步探讨了离聚物对PET的作用。     

Effect of the Counterion on the Cationic Polymerization Rate of Ethylene Oxide by Trityl Salts

The cationic polymerization of ethylene oxide by trityl salts (BF₄ ^?, SbCl₆ ^?, AsF₆ ^?, and PF₆ ^? as counterions) in nitrobenzene at different temperatures has been studied. The kinetic analysis was carried out by use of an automatic manometer, and it showed that the polymerization rate constant depends neither on the counterion type nor on the initial initiator concentration. These facts allowed us to conclude that macrocations and macroion pairs have the same reactivity.     

铁二亚胺配合物与水解乙基铝催化乙烯齐聚的研究

Ethylene oligomerization and polymerization catalyzed by α-diimine Pd(Ⅱ) or Ni(Ⅱ) complexes have been reported[1,2].     

环氧乙烷均聚反应机理的理论研究

借助量子化学理论计算方法对环氧乙烷均聚反应历程进行了理论探讨．采用DFT中的B3LYP方法在6-311G^**基组下对环氧乙烷基态和激发态以及亲核试剂和亲电试剂进攻环氧乙烷反应产物进行几何构型全优化,确定了各物种的电子结构、电荷分布和键长等参数．运用前线轨道理论从微观电子结构层次上对环氧乙烷的各种均聚反应机理进行了分析,探讨了阳离子均聚和阴离子均聚机理的合理性．由于受到前线轨道对称性和能级差的限制,环氧乙烷的基态分子不能发生均聚,同样也不能发生自由基均聚;而当环氧乙烷基态分子被亲电试剂或亲核试剂进攻时,可以进一步生成新的亲电或亲核试剂从而引发环氧乙烷均聚．计算结果很好地阐明了实验事实．     

Micellization and Adsorption Parameters of Poly(Propylene Oxide)/Poly(Ethylene Glycol) Block and Graft Copolymers in Aqueous Medium

This work aims to measure the adsorption and micellization parameters of new water soluble nonionic amphiphilic block and graft copolymers based on hydrophilic poly (ethylene glycol) (PEG) and hydrophobic poly (propylene oxide) (PPO) at ambient temperature and normal atmospheric pressure. The chemical composition and molecular weights of the prepared copolymers were determined from ¹H NMR analyses. The surface properties of the prepared surfactants were determined by measuring the surface tension at different temperatures. The surface tension, critical micelle concentration, and surface activities were determined at different temperatures. Surface parameters such as surface excess concentration, the area per molecule at interface and the effectiveness of surface tension reduction were determined from the adsorption isotherms of the prepared surfactants. Some thermodynamic data for the adsorption and micellization process were calculated and are discussed.     

Oxidation of Ethylene Glycol on Oxide Catalysts

The catalytic activity of a series of metal oxides in oxidation of ethylene glycol was studied.     

^13C—NMR研究环氧乙烷—环氧丙烷无规共聚物的序列结构

利用高分辨核磁共振谱仪研究了环氧乙烷－环氧丙烷均聚物和无规共聚物的核磁共振主链碳谱。在对其链结构进行有效归属的基础上，讨论了不同配比聚合物的僚共振主链碳谱特点及其可能的单元链节排列顺序。     

A Study on Side Reactions of Hydroxyethylation of 3-Nitro-4- chlorobenzenesulfinic Acid with Ethylene Oxide

2-Nitro-4-(β-hydroxyethylsulfonyl)chlorobenzene (NHCB) is an important intermediate for C.I. Reactive blue 220 (NHCB) which can be obtained by reacting 3-nitro-4- chlorobenzenesulfinic acid (NCBS) with ethylene oxide (EO). ClO2NSO2H H2COCH2 ClO2NSO2CH2…     

~(13)C-NMR驰豫关于星形聚环氧乙烷聚乳酸嵌段共聚物的研究

本实验测定了星形聚环氧乙烷聚乳酸嵌段共聚物(S(P)-PEO-PLA)在溶液中核磁驰豫与温度、浓度、溶剂及聚合物组成比的关系,测定了线形嵌段共聚物(L-PEO-PLA)核磁驰豫与温度、聚合物组成比的关系。实验测定了两个驰预参数T_1和η_c。采用Cole-Cole相关时间分布,log-x~2分布及Diamord Lattice模型对测定结果进行了定量解析。本文研究结果为假设的“似细胞超微~+”结构形态的存在性提供了理论依据,表明S(P)-PEO-PLA作为药物载体很有希望。     

聚丙烯酰胺对石油磺酸盐／正丁醇混合胶束体系流变性的影响

研究了一定矿化度下，不同分子量、不同水解度的聚丙烯酰胺对石油磺酸盐／正丁醇混合胶事体系的流型、粘度等充变性质的影响。     

Compatibilizing effect of a graft copolymer on bacterial poly(3‐hydroxybutyrate)/poly(methyl methacrylate) blends

Blends of isotactic (natural) poly(3‐hydroxybutyrate) (PHB) and poly(methyl methacrylate) (PMMA) are partially miscible, and PHB in excess of 20 wt % segregates as a partially crystalline pure phase. Copolymers containing atactic PHB chains grafted onto a PMMA backbone are used to compatibilize phase‐separated PHB/PMMA blends. Two poly(methyl methacrylate‐g‐hydroxybutyrate) [P(MMA‐g‐HB)] copolymers with different grafting densities and the same length of the grafted chain have been investigated. The copolymer with higher grafting density, containing 67 mol % hydroxybutyrate units, has a beneficial effect on the mechanical properties of PHB/PMMA blends with 30–50% PHB content, which show a remarkable increase in ductility. The main effect of copolymer addition is the inhibition of PHB crystallization. No compatibilizing effect on PHB/PMMA blends with PHB contents higher than 50% is observed with various amounts of P(MMA‐g‐HB) copolymer. In these blends, the graft copolymer is not able to prevent PHB crystallization, and the ternary PHB/PMMA/P(MMA‐g‐HB) blends remain crystalline and brittle. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1390–1399, 2002