Vinyl Polymerization. 374. Radical Polymerization of Vinyl Monomer Initiated with Sodium Polystyrenesulfonate

The polymerization of vinyl monomer initiated by an aqueous solution of sodium polystyrenesulfonate (PSS-Na) was carried out at 85°C. Methyl methacrylate (MMA) and styrene were polymerized, while acrylonitrile was not. The rate of polymerization of MMA decreased with the increase of the degree of polymerization of PSS-Na. However, the polymerization was not initiated by sodium ethyl benzenesulfonate which was a unit molecule of PSS-Na. The polymerization proved to be a radical reaction. The polymerization was considered to commence with the formation of hydrophobic areas with PSS-Na in the aqueous phase. MMA is incorporated into these areas, and there the polymerization is initiated and proceeds. The hydrophobic areas were assumed to be similar to the micelles formed by anionic detergents such as sodium alkylbenzene sulfonate. An initiation mechanism is proposed.     

Vinyl Polymerization. 418. Polymerization of Vinyl Monomer Initiated by Betaine-Type Polymers in Aqueous Solution

Abstract

Three kinds of betaine-type polymers, which are macromolecular amphoteric electrolytes, were found to be able to polymerize vinyl monomers in aqueous solution through a radical mechanism without any further initiator. Betain-type polymers form hydrophobic areas (HA) in water. Vinyl polymerization commenced in the HA. The effect of the pH of the aqueous solution on polymerization was investigated.     

Vinyl Polymerization Initiated by Peroxydiphosphate. IV. Polymerization of Acrylonitrile Initiated by Peroxydiphosphate-Thioacetamide Redox System

Abstract

The kinetics of the aqueous polymerization of acrylonitrile initiated by the peroxydiphosphate-thioacetamide redox system was investigated at 35, 40, and 50°C. The rates of polymerization were measured at different concentrations of oxidant, activator, and monomer. Peroxydiphosphate alone did not initiate polymerization under deaerated and undeaerated conditions. Addition of certain water-miscible organic solvents and neutral salts depress the rate and conversion. On the basis of experimental observations of the dependence of the rate of polymerization on various variables, a suitable kinetic scheme has been proposed.     

Vinyl Polymerization Initiated by Sulfur Dioxide

Abstract

A number of monomers have been polymerized in the presence of catalytic and higher concentrations of SO₂. The addition of t-butyl hydroperoxide greatly accelerates the rate of polymerization. The use of ³⁵SO₂ indicates that at catalytic concentrations of SO₂ (10^?2 mole/liter), only one or two molecules of SO₂ are incorporated in the chain, but, at high SO₂ concentrations, copolymerization of SO₂ with vinyl monomers occurs.     

Vinyl Polymerization. 282. Vinyl Polymerization Initiated by Dimethylhydroxylamine-Titanous(lll) Chloride Redox System

Abstract

The polymerization of vinyl monomers initiated by dimethylhydroxylamine hydrochloride (DHA)-titanous(III) chloride redox system has been studied in water under a nitrogen atmosphere. In the polymerization of methyl methyacrylate (MMA) initiated by the above system, the rate of polymerization has been found to be proportional to [DHA]^0.5 for DHA concentrations of less than 2.06 × 10^?3 mole/liter, whereas at higher concentrations the rate tends to fall rapidly. The rate has also been found to be proportional to [Ti(m)] ^0.58 and to [MMA] ^1.0. The maximum rate of polymerization has been observed at a 1:1 molar ratio of DHA to Ti(III). The polymerization proceeded via a radical mechanism. The overall activation energy was estimated as 5.5 kcal/mole. It has been suggested that the reduction of dimethylhydroxylamine by titanous(III) chloride yields the dimethylamino radical, which initiates vinyl polymerization. An examination of the initiating capacity of the initiator system for the polymerization of some vinyl monomers has also been made.     

Vinyl Polymerization Initiated by Peroxydiphosphate. XI. Polymerization of Methyl Methacrylate Initiated by Peroxydiphosphate-Tartaric Acid Redox System

The polymerization of methyl methacrylate was studied using the peroxydiphosphate and tartaric acid redox system as the initiator. The rate of polymerization increases with increasing peroxydiphosphate concentration and the initiator exponent was computed to be 0.5. The rate of polymerization increases with increasing monomer concentration and the monomer exponent was computed to be unity. The reaction was carried out at three different temperatures, and the overall activation energy was computed to be 3.80 kcal/mol. The effect of certain surfactants on the rate of polymerization has been investigated and a suitable kinetic scheme has been proposed.     

Vinyl Polymerization. 269. Polymerization of Methyl Methacrylate Initiated by p,p'-Dimethoxydiphenyldiazomethane

Using p,p'-dimethoxydiphenyldiazomethane (DMDM) as initiator, the polymerization of methyl methacrylate (MMA) in benzene or in bulk was carried out. The initial rate of polymerization, R_p, was found to be expressed by the following equation:

R_p = k[DMDM]^0.53 [MMA]^0.84

The polymerization was confirmed to proceed by a radical mechanism. The over-all activation energy for the polymerization in benzene was calculated as 19.3 kcal/mole. The rate of thermal decomposition of DMDM was also measured in benzene and the rate equation was obtained as follows:

k_d (sec^?1) = 1.0 × 10¹⁵ exp (^?29.1 kcal/RT) (for 50-80°C)

Explanations of these observations are discussed in connection with those of the preceding papers.     

Polymerization of 2-Oxazolines. I. Cationic Polymerization of 2-Phenyl-2-oxazoline Initiated by Various Oxazolinium Salts of Monomer with Brbnsted Acids

Abstract

Various kinds of the complexes of 2-phenyl-2-oxazoline with various Bronsted acids were prepared. From the elementary analysis and spectroscopic analysis of the complex, it was identified to be an equimolar oxazolinium salt. The monomer could be polymerized with the oxazolinium salt to give N-benzoyl-polyethylenimine. The polymer yield in bulk polymerization was linearly proportional to the reaction time, and the number-average degree of polymerization of the polymer obtained at the complete conversion was proportional to the initial molar ratio of the monomer to the complex. The catalytic activities of the oxazolinium salts increased with a decrease in the pK_avalue of Bronsted acid in water. The results of the infrared spectroscopy and nuclear magnetic resonance spectroscopy of the oxazolinium salt at room temperature and elevated temperature indicated that the change of the double bond character of the imino and ether linkages is brought about by the complexation. On the basis of these results, the mechanism of the polymerization was proposed.     

Vinyl Polymerization. 287. Polymerization of Methyl Methacrylate Initiated by the Polyacrylonitrile-Water-Cupric Ion System

Abstract

Methyl methacrylate was found to be polymerized by the system polyacrylonitrile-water-cupric ion without any added initiator. Addition of carbon tetrachloride to this system greatly increased the polymerization rate. Acrylonitrile and styrene did not polymerize in this system. The kinetic behavior of polymerization was the same as the system consisting'of cellulose or nylon instead of polyacrylonitrile. When the flaky polyacrylo-nitrile was swelled or dissolved by the solvent DMF, the conversion and the degree of polymerization of the poly-methyl methacrylate formed decreased markedly. Commercial acrylic fiber also initiated polymerization but the activity was lower than with flaky polyacrylonitrile, even after steam treatment, because of the poor permeability of monomer into the fiber.     

Semicontinuous Emulsion Polymerization of Vinyl Acetate. Part I. Homopolymerization with Poly-(Vinyl Alcohol) and Nonionic Coemulsifier

The semicontinuous emulsion polymerization of vinyl acetate has been studied. Poly(vinyl alcohol) as a protective colloid and ethoxylated cetyl alcohol as a coemulsifier were used. The conversion and particle diameter were affected by the stirring speed and the coemulsifier distribution between initial reactor charge and continuously introduced monomer. The amount of unreacted monomer oscillates with time.     

Vinyl Polymerization. 439. Vinyl Polymerization Initiated by Poly(Ethylene Glycol] Diglycolic Acid or its Sodium Salt

Abstract

The polymerization of some kinds of vinyl monomer was found to occur in aqueous solutions of poly(ethylene glycol) diglycolic acid (PEG Acid) or sodium poly(ethylene glycol) diglycolate (PEG Acid Na) through radical mechanisms without any further initiator, as a so-called “uncatalyzed polymerization.” Although the initiating radical species for PEG Acid was determined to be the same as that for PEG Acid Na by means of the spin-trapping technique, the initiating ability of PEG Acid was higher than that of PEG Acid Na. These results are assumed to be attributable to the difference in the initiation mechanisms of the two systems and in the incorporating abilities of monomer into the hydrophobic areas formed by PEG Acid and PEG Acid Na.     

Vinyl Polymerization Initiated by Metal Chelates. III. Polymerization of Methyl Methacrylate Initiated by Vanadium(IV) Acetylacetonate Chelates

The polymerization of methyl methacrylate initiated by the vanadium acetylacetonate complex was investigated under a nitrogen atmosphere at 50°C. The effect of concentration of monomer, complex, acid, dioxane, inhibitor, and the effect of temperature on the rate of polymerization were studied. The rate of polymerization was found to increase upon increasing the concentrations of the monomer, the initiator, and the acid. The overall activation energy has been computed from the Arrhenius plot and a suitable kinetic scheme has been proposed.     

Vinyl Polymerization. 431. Vinyl Polymerizations Initiated by Block and Random Poly(Styrene-co-Sodium Methacrylate)

Abstract

The polymerization of some kinds of vinyl monomer was found to occur without an ordinary initiator in aqueous solutions of AB-type block or random copolymers of sodium methacrylate with styrene as a so-called “uncatalyzed polymerization.” Although the spin trapping technique showed that the initiation mechanism by the block copolymer was the same as that by the random copolymer, the initiating ability of the block copolymer was lower than that of the random copolymer. Such results are attributable to the difference in the incorporating ability of monomer into the micelles formed by the block copolymer and into the hydrophobic areas formed by the random copolymer.     

二苯基碘鎓盐引发氨酯型乙烯基醚热聚合

合成了2种固态氨酯型乙烯基醚PUE1和PUE2,并对其结构和性能进行了表征.研究发现,二芳基碘六氟磷酸盐(PI810)能引发PUE1和PUE2发生阳离子热聚合,热聚合温度远低于PI810的纯态热分解温度,且聚合转化率很高.初步认为热聚合机理是富电子的乙烯基醚双键和缺电子的二苯基碘盐阳离子之间形成中间态电荷转移复合物,降低了二苯基碘盐的热分解温度,进而生成引发活性种乙烯基醚阳离子自由基或质子酸,引发乙烯基醚的阳离子聚合反应.     

乙烯基单体正离子聚合中链增长速率常数的研究进展

碳正离子聚合中,聚合速率常数的测定方法通常包括电导法、绝热量热法、胺抑制法、止流光谱法及扩散计时法。在烷基乙烯基醚、苯乙烯及其衍生物和异丁烯等几种常见乙烯基单体的正离子聚合中,本文介绍不同测定方法得到的不同结构碳正离子(包括自由离子和离子对)的链增长速率常数(kp 和kp±)。     

Vinyl Polymerization. 371. Polymerization of Methyl Methacrylate Initiated by the System of Polyvinylferrocene and Carbon Tetrachloride

The polymerization of vinyl monomers initiated with the system of polyvinylferrocene (PVFc) and carbon tetrachloride (CCl₄) was carried out in dark. Methyl methacrylate (MMA) and acrylonitrile (AN) could be polymerized, while styrene (St) was hardly polymerized under the conditions used. The polymerization proceeded through a free-radical mechanism and was concluded to be initiated by attack of vinyl monomer, having a polarized vinyl group, on the charge-transfer complex of PVFc/CCl₄. In the polymerization of MMA, the initiating ability of PVFc was much larger than that of ferrocene (Fc-H) or poly(ferrocenylmethyl methacrylate) (PFMMA) and was comparable to that of polyferrocenylenemethylene (PFM). The overall activation energy was estimated to be 34.2 kJ/mole.     

Vinyl Polymerization by Metal Complexes. XV. Polymerization of Acrylonitrile Initiated by Imidazole-Copper(II) Complex

The polymerization of acrylonitrile initiated with the imidazole-copper (II) complexes was studied in dimethylsulfoxide solution. The ability of the complexes to initiate polymerization seems to depend on their anion. 2-Substituted imidazole-copper (II) complexes of the type, CuL₄X₂ (L = imidazole as ligand and X = anion), were also found to initiate vinyl polymerization. From the data of electronic spectra in dimethylsulfoxide solution, the initiation mechanism is discussed in terms of the formation of the active species by the interaction of the complex with monomer molecules.     

Polymerization of Vinyl Chloride at Reduced Monomer Accessibility. I. Polymerization at Subsaturation Pressure with Suspension PVC as a Seed

Vinyl chloride was polymerized at 40–96% of saturation pressure in water suspended systems at 55°C with suspension PVC as a seed. The monomer was continuously charged as vapor from a storage vessel kept at lower temperature. Characterization included molecular weight distribution (MWD) and degree of long-chain branching (LCB) by GPC and viscometry, thermal dehydrochlorination, microscopy, and technical standard tests. A granular seed was necessary to obtain granular polymer and reasonable polymerization rate. In properly seeded systems with monomer-soluble initiator, crust formation is very low. With monomer-soluble initiator the polymerization reactions are restricted to the seed polymer, comprise its total structure, reducing its porosity. At pressure near saturation, molecular weight increased with conversion, and autoacceleration occurred. The changes in molecular weight are presumably due to the lack of a liquid monomer phase, which reduces the mobility of the radicals leading to decreased termination. At decreasing polymerization pressure the mobility is further reduced due to de-swelling of the gel. At low pressure the polymerization rate decreased, the amount of low molecular weight material increased, and considerable long-chain branching occurred as a result of monomer depletion. With water-soluble initiator (at pressure near saturation), new tiny particles were formed in the water phase at the boundary to the seed particles. The seed structure remained unchanged. The polymer formed showed broad MWD and high LCB. No marked reduction in polymerization rate was observed. The dehydrochlorinatlon measurements indicate that the end groups and not the branch points are responsible for the decrease in thermal stability noticed.     

炭黑对乙烯基单体自由基聚合反应的影响

用悬浮聚合法制备静电复印用增色剂时，着色剂炭黑在反应体系中具有明显的阻聚作用。研究了炭黑对反应活性不同的乙烯基单体和不同引发剂体系聚合反应的影响。通过在炭黑表面进行接枝，以降低炭黑对聚合反应的干扰。