End‐Functionalized Palladium SCS Pincer Polymers via Controlled Radical Polymerizations

A direct and facile route toward semitelechelic polymers, end‐functionalized with palladated sulfur–carbon–sulfur pincer (Pd^II‐pincer) complexes is reported that avoids any post‐polymerization step. Key to our methodology is the combination of reversible addition‐fragmentation chain‐transfer (RAFT) polymerization with functionalized chain‐transfer agents. This strategy yields Pd end‐group‐functionalized materials with monomodal molar mass dispersities (Đ ) of 1.18–1.44. The RAFT polymerization is investigated using a Pd^II‐pincer chain‐transfer agent for three classes of monomers: styrene, tert‐butyl acrylate, and N‐isopropylacrylamide. The ensuing Pd^II‐pincer end‐functionalized polymers are analyzed using ¹H NMR spectroscopy, gel‐permeation chromatography, and elemental analysis. The RAFT polymerization methodology provides a direct pathway for the fabrication of Pd^II‐pincer functionalized polymers with complete end‐group functionalization.

     

Synthesis and polymerization of styrene monomers bearing spiroorthoester structure and volume change during crosslinking by double ring‐opening of the pendant spiroorthoesters of the obtained polymers

Novel styrene monomers bearing a five or seven‐membered spiroorthoester structure (SOE5, SOE7) were synthesized and their radical polymerizations as well as volume change during crosslinking of the obtained polymers were investigated. SOE5 and SOE7 were prepared from 4‐vinylbenzyl glycidyl ether and γ‐butyrolactone or ε‐caprolactone using boron trifluoride diethyl ether complex as a catalyst, respectively. Radical polymerizations of these monomers using 2,2′‐azobisisobutyronitrile (AIBN) gave the corresponding styrene‐based polymers with keeping the spiroorthoester structures unchanged. These polymers could be transformed to networked polymers by heating with a sulfonium antimonate, a thermally latent cationic polymerization initiator. Copolymerization of SOE5 or SOE7 with styrene at various compositions was carried out to efficiently obtain the corresponding copolymers, respectively. These polymers and copolymers showed little volume shrinkage or slight volume expansion during the crosslinking. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1790–1795     

Synthesis of well‐defined naphthalene and photo‐labile group‐labeled polystyrene via ATRP

The atom transfer radical polymerizations of styrene were successfully carried out in bulk and solution, respectively, at 115 °C, with a novel photoiniferter reagent, (1‐naphthyl)methyl N,N‐diethyldithiocarbamate (NMDC), as an initiator in the presence of copper (I) bromide and N,N,N′,N″,N″‐pentamethyldiethylenetriamine. The results showed that NMDC was an effective initiator with high initiation efficiency for ATRP of St. The polymerization rate was first‐order with respect to the monomer concentration and the molecular weights of the obtained polystyrene (PS) increased linearly with the monomer conversion, with very narrow molecular weight distributions (M_w/M_n = 1.07–1.29). The functionalized naphthalene‐labeled PS bearing N,N‐(diethylamino)dithiocarbamoyl group which was confirmed by ¹H NMR analysis, and chain extension of the PS exhibited fluorescence and ultraviolet absorption in chloroform (CHCl₃). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 510–518, 2006     

Chemoenzymatic Synthesis of Branched Polymers

Summary: The combination of enzymatic polymerization with ATRP for the synthesis of branched (block) copolymers was investigated. Heterotelechelic polycaprolactone macroinimer was synthesized in a one‐pot enzymatic procedure by using 2‐hydroxyethyl α‐bromoisobutyrate as a bifunctional initiator. A polymerizable end group was introduced by subsequent in situ enzymatic acrylation with vinyl acrylate. Branched polymers were obtained by subsequent atom transfer radical polymerization (ATRP).

Enzymatic synthesis of heterotelechelic macromonomers and subsequent self condensing vinyl polymerization by ATRP.     

Statistical fluorinated copolymers from heterogeneous atom transfer radical copolymerization of styrene and 2,2,2‐trifluoroethyl methacrylate with similar reactivity ratios

Fluorinated copolymers with statistical structure of azeotropic or gradient composition were prepared from heterogeneous atom transfer radical copolymerizations of styrene (S) and 2,2,2‐trifluoroethyl methacrylate (T). The polymerization kinetic studies show that while the propagation rate constant of S increased with a decreasing S content in the comonomer feed ratio, the propagation rate of T decreased with decreases of the S content in the comonomer feed ratio. The polymerization rate and controllability of the heterogeneous ATRP of S and T were regulated by the solubility of Cu(II)/ligand in the reaction mixture, based on a mechanistic analysis and solubility tests of the Cu(II)/ligand system in the reaction media. The reactivity ratios of S and T were 0.22 and 0.35, as evaluated from kinetic analysis of monomer conversions higher than 35%. These statistical polymers self‐assembled in T to form giant vesicles GVs) with broad diameter distribution in the range of 1–10 μm. Unlike the methods normally used to prepare gradient copolymers by spontaneous controlling with feeding model or batch polymerization of comonomers with obvious differences in the reactivity ratio, in this contribution, we report a novel synthetic strategy for preparing gradient copolymers can also be prepared from both monomers with very similar reactivity ratio. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Catenated PS–PMMA Block Copolymers via Supramolecularly Templated ATRP Initiator Approach

A novel route to synthesize catenated macrocyclic PS–PMMA block copolymers is demonstrated via combination of supramolecular chemistry and controlled radical polymerization (CRP). Polymerization of styrene with bromopropionate ester initiator coupled with phenanthroline Cu(I) complex affords a four arm PS macroinitiator, which upon further chain extension by polymerization of MMA generates a four arm PS–PMMA block copolymer. Intramolecular coupling of PS–PMMA–Br arms via low temperature styrene‐assisted atom transfer radical coupling (ATRC) leads to the formation of PS–PMMA catenand, which generates the metal‐free catenated macrocyclic PS–PMMA block copolymer after removal of Cu metal. The interlocked structures of catenated block copolymers are confirmed by GPC, NMR, and AFM image analysis.     

Uniform PEO Star Polymers Synthesized in Water via Free Radical Polymerization or Atom Transfer Radical Polymerization

Amphiphilic star shaped polymers with poly(ethylene oxide) (PEO) arms and cross‐linked hydrophobic core were synthesized in water via either conventional free radical polymerization (FRP) or atom transfer radical polymerization (ATRP) techniques using a simple “arm‐first” method. In FRP, PEO based macromonomers (MM) were used as arm precursors, which were then cross‐linked by divinylbenzene (DVB) using 2,2′‐azoisobutyronitrile (AIBN). Uniform star polymers ( < 1.2) were achieved through adjustment of the ratio of PEO MM, DVB, and AIBN. While in case of ATRP, both PEO MM, and PEO based macroinitiator (MI) were used as arm precursors with ethylene glycol diacrylate as cross‐linker. Even more uniform star polymers with less contamination by low MW polymers were obtained, as compared to the products synthesized by FRP.

     

Atom Transfer Radical Polymerization of Styrene Using Multifunctional Iniferter Reagents as Initiators

Summary: Two multifunctional iniferters, 1,4-bis-(α-N,N-diethyldithiocarbamyl-isobutyryloxy)-benzene (BDCIB) and 1,3,5-tris-(α-N,N-diethyldithiocarbamyl-isobutyryloxy)-benzene (TDCIB), were successfully synthesized and used as initiators to initiate the polymerization of styrene in the presence of a CuBr/PMDETA complex. The polymerization results demonstrated that the kinetic plots in all cases were first-order to the monomer, the molecular weight of the polymers increased linearly with the monomer conversion; meanwhile, the molecular weight distribution of the polymer was kept to a very low value (M_w/M_n ≤ 1.35). Furthermore, the measured molecular weights were very close to the calculated values, which indicated the high efficiency of the initiator for the polymerization of styrene. The effect of catalyst concentration and initiator concentration was not obvious and the influence of polymerization temperature was apparent, and the polymerization rate increased with the polymerization temperature. The results of chain-extension and ¹H NMR analysis proved that the polymer obtained was capped with diethylthiocarbamoylthiy (DC) group.     

引发剂结构对原子转移自由基聚合反应的影响

研究了三种不同结构的引发剂,溴代乙酸乙酯（EBrA)、α-溴代丁乙酯（EBrB)、α－溴代异丁酸乙酸（EBriB)引发的苯乙烯的原子转移自由基聚合反应（ATRP）。发现EBrA引发的苯乙烯的ATRP不是“活性”聚合。EBriB引发的苯乙烯的ATRP引发效率不够高,也不是典型的“活性”聚合。EBrB引发的苯乙烯的ATRP是较为典型的“活性”聚合：聚合物的分子量可以通过调节单体／引发剂的投料量及反应时间来控制,所得聚合物的分子量分布很窄,且有随转化率的增加而逐渐变窄的趋势。     

Synthesis of Branched Polymers under Continuous‐Flow Microprocess: An Improvement of the Control of Macromolecular Architectures

Polymerization reactions can benefit from continuous‐flow microprocess in terms of kinetics control, reactants mixing or simply efficiency when high‐throughput screening experiments are carried out. In this work, we perform for the first time the synthesis of branched macromolecular architecture through a controlled/‘living' polymerization technique, in tubular microreactor. Just by tuning process parameters, such as flow rates of the reactants, we manage to generate a library of polymers with various macromolecular characteristics. Compared to conventional batch process, polymerization kinetics shows a faster initiation step and more interestingly an improved branching efficiency. Due to reduced diffusion pathway, a characteristic of microsystems, it is thus possible to reach branched polymers exhibiting a denser architecture, and potentially a higher functionality for later applications.     

Atom‐Transfer Radical Batch and Semibatch Polymerization of Styrene

Batch and semibatch styrene polymerizations are carried out using a heterogeneous ATRP catalyst system that provides excellent molecular‐weight control. The observed initiator efficiency is lower for semibatch operation due to the high initiator concentrations required to make a low‐MW polymer. Experiments verified that the insoluble metal complex does not participate in the polymerization and that Cu(I) solubility is an order of magnitude higher than that of Cu(II). A mechanistic model, using kinetic coefficients from literature and the solubility data from this study, provides a good representation of the experimental results.

     

Preparation of H‐shaped ABCAB terpolymers by atom transfer radical coupling

H‐shaped ABCAB terpolymers composed of polystyrene (PS) (A), poly(ethylene oxide) (PEO) (B), and poly(tert‐butyl acrylate) (PtBA) (C) were prepared by atom transfer radical coupling reaction using ABC star terpolymers as precursors, CuBr and N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as catalysts, and nanosize copper as the reducing agent. The synthesis of 3‐miktoarm star terpolymer PS‐PEO‐(PtBA‐Br) involved following steps: (1) the preparation of PS with an active and an ethoxyethyl‐ptotected hydroxyl group at the same end; (2) the preparation of diblock copolymer PS‐b‐PEO with ethoxyethyl‐protected group at the junction point through the ring‐opening polymerization (ROP) of EO; (3) after de‐protection of ethoxyethyl group and further modification of hydroxyl group, tBA was polymerized by atom transfer radical polymerization using PS‐b‐PEO with 2‐bromoisobutyryl functional group as macroinitiator. The H‐shaped terpolymer could be successfully formed by atom transfer radical coupling reaction in the presence of small quantity of styrene, CuBr/PMDETA, and Cu at 90 °C. The copolymers were characterized by SEC, ¹H NMR, and FTIR in detail. The optimized coupling temperature is 90 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 59–68, 2009     

In situ Fourier transform near infrared spectroscopy monitoring of copper mediated living radical polymerization

In situ Fourier transform near infrared (FTNIR) spectroscopy was successfully used to monitor monomer conversion during copper mediated living radical polymerization with N‐(n‐propyl)‐2‐pyridylmethanimine as a ligand. The conversion of vinyl protons in methacrylic monomers (methyl methacrylate, butyl methacrylate, and N‐hydroxysuccinimide methacrylate) to methylene protons in the polymer was monitored with an inert fiber‐optic probe. The monitoring of a poly(butyl methacrylate‐b‐methyl methacrylate‐b‐butyl methacrylate) triblock copolymer has also been reported with difunctional poly(methyl methacrylate) as a macroinitiator. In all cases FTNIR results correlated excellently with those obtained by ¹H NMR. On‐line near infrared (NIR) measurement was found to be more accurate because it provided many more data points and avoided sampling during the polymerization reaction. It also allowed the determination of kinetic parameters with, for example, the calculation of an apparent first‐order rate constant. All the results suggest that FTNIR spectroscopy is a valuable tool to assess kinetic data. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4933–4940, 2004     

Atom transfer radical polymerization of styrene using the novel initiator ethyl 2‐N,N‐(diethylamino)dithiocarbamoyl‐butyrate

The atom transfer radical polymerizations (ATRPs) of styrene initiated by a novel initiator, ethyl 2‐N,N‐(diethylamino)dithiocarbamoyl‐butyrate (EDDCB), in both bulk and solution were successfully carried out in the presence of copper(I) bromide (CuBr) and N,N,N′,N″,N″‐pentamethyldiethylenetriamine at 115 °C. The polymerization rate was first‐order with respect to the monomer concentration, and the molecular weights of the obtained polymers increased linearly with the monomer conversions with very narrow molecular weight distributions (as low as 1.17) up to higher conversions in both bulk and solution. The polymerization rate was influenced by various solvents in different degrees in the order of cyclohexanone > dimethylformamide > toluene. The molecular weight distributions of the produced polymers in cyclohexanone were higher than those in dimethylformamide and toluene. The results of ¹H NMR analysis and chain extension confirmed that well‐defined polystyrene bearing a photo‐labile N,N‐(diethylamino)dithiocarbamoyl group was obtained via ATRP of styrene with EDDCB as an initiator. The polymerization mechanism for this novel initiation system is a common ATRP process. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 32–41, 2006     

Living radical emulsion polymerization using the nanoprecipitation technique: An extension to atom transfer radical polymerization

Living radical polymerizations of styrene were performed under emulsion atom transfer radical polymerization conditions with latexes prepared by a nanoprecipitation technique recently developed for the stable free‐radical polymerization process. Latexes were prepared by the precipitation of a solution of low‐molecular‐weight polystyrene in acetone into a solution of a surfactant in water. The resulting particles were swollen with styrene and then heated. The effects of various surfactants and hydrophobic ligands, the reaction temperature, and the ligand/copper(I) bromide ratio were studied. The best results were obtained with the nonionic surfactant Brij 98 in combination with the hydrophobic ligand N,N‐bis(2‐pyridylmethyl)octadecylamine and a ligand/copper(I) bromide ratio of 1.5 at a reaction temperature of 85–90 °C. Under these conditions, latexes with good colloidal stability with average particle diameters of 200 nm were obtained. The molecular weight distributions of the polystyrenes were narrow, although the experimental molecular weights were slightly larger than the theoretical ones because not all the macroinitiator appeared to reinitiate. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4027–4038, 2006     

Synthesis and radical polymerization of styrene‐based monomer having a five‐membered cyclic dithiocarbonate structure

A styrene‐based monomer having a five‐membered cyclic dithiocarbonate structure, 4‐vinylbenzyl 1,3‐oxathiolane‐2‐thione‐5‐ylmethyl ether (VBTE), was synthesized from 4‐vinylbenzyl glycidyl ether (VBGE) and carbon disulfide in the presence of lithium bromide in 86% yield. Radical polymerization of VBTE in dimethyl sulfoxide by 2,2′‐azobisisobutyronitrile was carried out at 60 °C to afford the corresponding the polymer, polyVBTE, in 64% yield. PolyVBTE with number‐averaged molecular weight higher than 31,000 was obtained. The glass transition temperature (T_g) and 5 wt % decomposition temperature (T_d5) of the polyVBTE were evaluated to be 66 and 264 °C under nitrogen atmosphere by differential scanning calorimetry and thermal gravimetry analysis, respectively. It was confirmed that a polymer consisting of the same VBTE repeating unit could also be obtained via polymer reaction, that is, a lithium bromide‐catalyzed addition of carbon disulfide to a polyVBGE prepared from a radical polymerization of VBGE. Copolymerization of VBTE and styrene with various compositions efficiently gave copolymers of VBTE and styrene. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Combining Atom Transfer Radical Polymerization and Click Chemistry: A Versatile Method for the Preparation of End‐Functional Polymers

Summary: The bromine chain ends of well‐defined polystyrene ( = 2 700 g · mol⁻¹, = 1.11) prepared using ATRP were successfully transformed into various functional end groups (ω‐hydroxy, ω‐carboxyl and ω‐methyl‐vinyl) by a two‐step pathway: (1) substitution of the bromine terminal atom by an azide function and (2) 1,3‐dipolar cycloaddition of the terminal azide and functional alkynes (propargyl alcohol, propiolic acid and 2‐methyl‐1‐buten‐3‐yne). The “click” cycloaddition was catalyzed efficiently by the system copper bromide/4,4′‐di‐(5‐nonyl)‐2,2′‐bipyridine. In all cases, ¹H NMR spectra indicated quantitative transformation of the chain ends of polystyrene into the desired function.

Preparation of well‐defined functional polymers possessing diverse chain‐end functionalities by the combination of atom transfer radical polymerization and click chemistry.     

Living/controlled radical polymerization of styrene with a new initiating system: DCDPS/FeCl3/PPh3

The living/controlled radical polymerization of styrene was investigated with a new initiating system, DCDPS/FeCl₃/PPh₃, in which diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS) was a hexa‐substituted ethane thermal iniferter. The polymerization mechanism belonged to a reverse atom transfer radical polymerization (ATRP) process. The polymerization was controlled closely in bulk (at 100 °C) or in solution (at 110 °C) with a high molecular weight and quite narrow polydispersity (M_w/M_n = 1.18 ∼ 1.28). End‐group analysis results by ¹H NMR spectroscopy showed that the polymer was ω‐functionalized by a chlorine atom, which also was confirmed by the result of a chain‐extension reaction in the presence of a FeCl₂/PPh₃ or CuCl/bipy (2,2′‐bipyridine) catalyst via a conventional ATRP process. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 101–107, 2000     

Iron‐mediated atom transfer radical polymerization of styrene with tris(3,6‐dioxaheptyl) amine as a ligand

The atom transfer radical bulk polymerization of styrene with FeX₂ (X = Br or Cl)/tris(3,6‐dioxaheptyl) amine as the catalyst system was successfully implemented at 110 °C. The number‐average molecular weight of the polymers with a narrow molecular weight distribution (weight‐average molecular weight/number‐average molecular weight = 1.2–1.5) increased linearly with the monomer conversion and matched the predicted molecular weight. The polymerization rate, initiation efficiency, and molecular weight distribution were influenced by the selection of the initiator and iron halide. The high functionality of the halide end group in the obtained polymers was confirmed by both ¹H NMR and a chain‐extension reaction. Because of its water solubility, the iron complexes could be removed easily from the reaction mixture through the washing of the polymerization mixture with water. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 483–489, 2006