Quasiliving Carbocationic Poiymerization. III. Quasiliving Polymerization of lsobutylene

The polymerization of isobutylene has been investigated by the use of the steady, slow, continuous monomer addition technique in the presence of a variety of initiating systems, i.e., “H₂O”/TiCl₄, “H₂O”/AlCl₃, C₆H₅C(CH₃)₂Cl/TiCl₄, p-ClCH₂ C₆(CH₃)₄* CH₂Cl/AlCl₃ at -50°C. Quasiliving polymerizations have been obtained with the “H₂O” and C₆H₅(CH₃)₂Cl/TiC1₄ systems in 60/40 v/v n-hexane/methylene chloride solvent mixtures with very slow monomer input. After a brief “flash” polymerization, the M _n of PIB increased linearly with the cumulative amount of monomer added (consumed); however, the number of polymer molecules formed also increased, indicating the presence of chain transfer to monomer. With the “H₂O”/TiCl₄ initiating system, M _n,max was 56,000 and M _w /M _n < 2.0. By the use of the C₆H₅C(CH₃)₂CL/TiCl₄ initiating system, quasiliving polymerization has been achieved and chain transfer could virtually be eliminated.     

Quasiliving Carbocationic Polymerization. VIII. Quasiliving Polymerization of Methyl Vinyl Ether and Its Blocking from Quasiliving Poly(isobutyl Vinyl Ether) Dication

Quasiliving carbocationic polymerization of methyl vinyl ether (MVE) was achieved with the p-dicumyl chloride (p-DCC)/AgSbF₆ initiator system by the slow and continuous monomer-addition (quasiliving) technique. A polar solvent (CH₂Cl₂) and a low reaction temperature (-70°C) were optimum for the quasiliving MVE polymerization. Under these conditions, the number-average molecular weight (M _n) of poly(MVE) increased linearly with the cumulative weight of added monomer (W_MVE), and linear M _n versus W_MVE plots passed through the origin. M _n's were inversely proportional to the initial initiator (p-DCC) concentration. Reactions in a nonpolar solvent (toluene) at -70°C or in a polar solvent (CH₂Cl₂) at ?30°C resulted in deviations from these quasiliving characteristics. Block polymerization of MVE from quasiliving poly(isobutyl vinyl ether) dications by the quasiliving technique (p-DCC/AgSbF₆ initiator, CH₂Cl₂ solvent,(-70°C) led to novel isobutyl vinyl ether (IBVE)-MVE block polymers in high yield (>93 wt%) and at high blocking efficiency. The block polymers, most likely poly(MVE-b-IBVE-b-MVE), having M _n = 10,900–14,000 [M _n(center block) = 6,200–9,0001, were soluble in n-heptane and insoluble in water, and gave hazy homogeneous solutions when dissolved in methanol at room temperature.     

Living Carbocationic Polymerization. XLIX. Two-Stage Living Polymerization of Isobutylene to Di-tert-chlorine Telechelic Polyisobutylene

Abstract

A two-stage process was developed for the living polymerization of isobutylene (IB) employing di-tert-alcohol initiators in conjunction with BCl₃ coinitiator in the first or initiation stage, followed by TiCl₄ coinitiator in the second or propagation stage; the process was shown to yield high molecular weight (up to M ⁿ 20,000), narrow molecular weight distribution (MWD) M ^w/M ⁿ = 1.1–1.2) di-tert-chlorine telechelic polyisobutylenes (^tCl-PIB-Cl^t). The initiation stage involves the homogeneous solution living polymerization of IB induced by the di-tert-alcohol/BCl₃ combination in the presence of an electron donor such as N,N-dimethylacetamide in CH₃Cl solvent at ?80°C and proceeds up to M ⁿ < 5000; this is followed by the propagation stage in which TiCl₄ and the bulk of IB plus a sufficient amount of n-C₆H₁₄ are added to the charge to bring the solvent composition to CH₃Cl/n-C₆H₁₄ 60/40 v/v and the living polymerization is continued until high M ⁿ product is obtained. This two-stage process was developed because 1) it employs very inexpensive chemicals; 2) di-tert-alcohol/BCl₃ combinations initiate living IB polymerization in CH₃Cl but the product after reaching M ⁿ ≤ 5000 precipitates out of the CH₃Cl solution, and di-tert-alcohol/BCl₄ combinations do not initiate IB polymerization; and 3) di-tert-alcohol/BCl₃ systems do not initiate (or only very slowly) the living polymerization of IB in CH₃Cl/n-C₆H₁₄ mixtures, whereas similar TiCl₄-based systems do. The polymerization remains living during both stages although the propagating species and solvent polarity are profoundly altered. The livingness of the system has been analyzed by kinetic experiments and the structure of the ^tCl-PIB-Cl^t product by routine spectroscopic means.     

Ultrasonic Solution Degradations of Polystyrene and Substituted Polystyrenes in Tetrahydrofuran as Solvent

Abstract

Ultrasonic (70 W, 20 kHz) solution (2% THF) degradations of polystyrene (PS), poly(α-methylstyrene) (PαMeS), poly(p-isopropyl α-methylstyrene) (PpiPrαMeS), poly(p-chlorostyrene) (PpCIS), poly(p-bromostyrene) (PpBrS), and poly(p-methoxystyrene) (PpOMeS) have been carried out in tetrahydrofuran at 27° C. The average number of chain scissions S (where S = [(M _n)₀/(M _n)_t] - 1), computed from the overall values of [(M _n)₀ and (M _n)_t, were found to be different from those of S' (where S' = α([(M _n)₀/(M _n)_t] - 1)) based on the component (only that part of the polymer which is involved in degradation) data of the weight fraction (α), (M _n)₀, and (M _n)_t), S' for polystyrene and substituted polystyrene follows the order PS gt; PpCIS gt; PpiPrαMeS gt; PpBrS gt; PpOMeS gt; PαMeS. In the case of PS where degradations were also carried out at -20°C, lowering of the temperature increased the weight fraction of polymer degraded as well as S. Based on the viscosity and GPC data, it is concluded that the ultrasonic solution degradation of PS does not lead to branched polymers.     

New Interpretations: Molecular Weight Averages for a Polymer

The statement is often made in the polymer literature, without proof, that M _z ≤ M _w ≤ M _n, where M _z, M _w, and M _n are the z-, z weight-, and number-average molecular weights respectively. Four proofs of a generalization of these inequalities are given. It is shown that a higher-order molecular weight average is larger than a lower-order one, regardless of the form of the molecular weight distributions, except for the case when all the molecules have the same molecular weight. A brief discussion of the viscosity-average molecular weight is also included.     

Quasiliving Carbocationic Polymerization. IV. Polymerization of p-tert-Butylstyrene

The mechanism of polymerization of p-tert-butylstyrene (ptBuSt) initiated by the cumyl chloride/BCl₃ initiating system in CH₂Cl₂ at -50°C has been investigated. At and below ～0.4 M ptBuSt, quasiliving polymerizations proceed, i.e., initiation is instantaneous, termination is absent or reversible, and chain transfer to monomer can be suppressed or eliminated. In the quasiliving range the M _n versus [ptBuSt]₀ plot is linear and passes through the origin, and a M _w/M _n decreases much below 2.0 with decreasing [ptBuSt]. GPC traces change from broad multimodal to narrow monomodal and the color of polymerization charges change from colorless to golden-yellow with decreasing [ptBuSt]. The effect of temperature jump subsequent to monomer addition has been examined; however, it does not explain the peculiar monomer concentration effect on the mechanism. Changes in the ionicity may be responsible for this phenomenon.     

Living Carbocationic Polymerization. Li. Living Carbocationic Copolymerization of Indene and p-Methylstyrene. 1. Demonstration of the Living and Random Copolymerization of Indene and p-Methylstyrene

Abstract

The living carbocationic polymerization and copolymerization of indene (Ind) and p-methylstyrene (pMeSt) have been investigated by the use of the 2-chloro-2,4,4-trimethylpentane (TMPCl)/TiCl₄ and the 2-chloro-2-propylbenzene (cumyl chloride, CumCl)/BCl₃ initiating systems in the presence of triethylamine (Et₃N) as electron donor and CH₃Cl or CH₃Cl/QH14 mixed solvents at ?80°C. The TMPCl/TiCl₄ initiating system gives essentially living copolymerization with slow initiation up to M _n ≈ 20,000. The CumCl/BCl₃ initiating system also induces living Ind homopolymerization up to at least M _n ≈ 13,000. The homopolymerization of pMeSt with the latter initiating system, however, is not living as it shows evidence for a large amount of chain transfer. Thus, with the CumCl/BCl₃ combination a small amount of chain transfer has apparently been observed in the presence of 50% of pMeSt in the charge. Reactivity ratio studies, fractionation, ¹H- and ¹³C-NMR spectroscopy, and glass transition temperature (T_g ) investigations indicate that virtually random Ind-co-pMeSt copolymers of M _n ≈ 20,000 can be obtained under suitable conditions. The T_g of the copolymers can be controlled between ≈115°C (the T_g of PpMeSt) and ≈194°C (the T_g of PInd) by the relative composition of the two monomers in the charge.     

Atranes

Methods for the preparation of bis(1-silatranyloxy)alkanes, - , where R=-(CH₂)_n-(n=2–6), -CH₂CH(CH₃)-, and-CH₂CH₂OCH₂CH₂-,were developed on the basis of reactions of alkanediols with 1-hydro- and 1-ethoxysilatrane. In the presence of excess alkanediol these reactions give less stable 1-(hydroxyalkoxy)silatranes, , that are difficult to isolate.     

Preliminary Study of Cationic Copolymerization of α-Methylstyrene and Isobutyl Vinyl Ether. II

α-Methylstyrene (α-MS) and isobutyl vinyl ether (IBVE) were copolymerized by using the H₂O/EtAlCl₂ initiator system and CH₂Cl₂ and CH₃Cl solvent in the temperature range from -30 to -90°C. As compared to homopolymerization of α-MS, both yields and molecular weights are reduced upon addition of small amounts of IBVE to the feed. The reactivity ratios were calculated by the method of Kelen and Tödös as well as the Fineman and Ross method, and the combined effect of change of solvent and temperature on reactivity ratios was determined. Effects of feed composition and temperature on the copolymer yield, composition, and number-average molecular weight M _n were studied in detail. M _n showed a novel exponential dependence on the IBVE concentration in the feed. The overall activation energies of molecular weight were determined from the Arrhenius plots for both homo-and copolymerization systems. Based on these and the yield data, a speculation is made regarding reaction mechanism for molecular weight control. NMR and DTA data are reported, which establish the random nature of the copolymers.     

Quasiliving Carbocationic Polymerization. VII. Block Polymerization of α-Methylstyrene from Quasiliving Poly(isobutyl Vinyl Ether) Dication

Poly(α-methylstyrene-b-isobutyl vinyl ether-b-α-methylstyrene) triblock polymers have been prepared by blocking α-methyl-styrene (αMeSt) from biheaded quasiliving poly(isobuty1 vinyl ether) (PIBVE) cations generated with the bifunctional p-dicumyl chloride/AgSbF₆ initiating system in methylene chloride solvent at -90°C. The products were fractionated with 2-propanol, a good solvent for PIBVE and a nonsolvent for PaMeSt. The 2-propanol-insoluble fractions had much higher molecular weights (M _n = 30,500–69,100) than the starting PIBVE (M _n =6,600–10,600) and contained 13–29 wt% IBVE together with 87–71 wt% αMeSt units. The 2-propanol-soluble fractions (M _n = 7,300–11,600) contained ～90 wt% IBVE and ～10 wt% αMeSt units.     

Crystallizable Polyphenylacetylene-Preparation and Solution Properties

The molecular weight distribution (MWD) of crystallizable polyphenylacetylene prepared near room temperature in the presence of ferric acetylacetonate and triethylaluminum was determined through use of fractions characterized by vapor pressure osmometry and gel permeation chromatography (GPC). The number- and weight-average molecular weights (M _n and M _w) are both less than the molecular weight corresponding to the maximum of the weight distribution function, which lacks a high molecular weight tail. M _wandM _n is less than is consistent with models allowing for chain termination characteristic of vinyl polymers. GPC elution volumes are much less than those characteristic of polystyrene of similar molecular weight, and the Mark-Houwink exponent is high (2.4 for M _v 4800 to 6800). These data indicate more rodlike behavior than for polystyrene of equivalent molecular weight. The MWD and other data suggest intramolecular chain termination, possibly associated with the molecule's tendency to form paramagnetic defect states.     

Determination of the molecular masses of tetrafluoroethylene telomers by gel-permeation chromatography

Gel-permeation chromatography has been employed to study the molecular-mass distribution of tetrafluoroethylene telomers prepared through γ irradiation of 0.05–0.56 mol/l monomer solutions in acetone. The molecular-mass-retention-volume V _R calibration dependence has been plotted from chromatograms of perfluoroenanthic and perfluoropelargonic acids (F(CF₂-CF₂) _n COOH; n = 3 or 4, respectively). The measured V _R-log n curve is located parallel to that plotted earlier for oligo(oxyethylene glycol)s (OH-(CH₂-CH₂O) _n -OH) and is shifted along the volume axis. The shift value is determined by the ratio between logarithmic volumes of chain units of these oligomers. The shift agrees with the assumption that the retention volumes of oligomers with the same spatial chain structure are proportional to the logarithm of the ratio between their van der Waals volumes. This assumption is supported by the quantum-chemical calculation of the molecular volumes of oligomers composed of (CH₂-CH₂) _n , (CH₂-CH₂O) _n , and (CF₂-CF₂) _n fragments. As the concentration of tetrafluoroethylene in the initial solution is increased, the average length of (CF₂-CF₂) _n chains increases from \(\bar n\) ≈ 3 to \(\bar n\) ≥ 8. The maximum values of n = 12–15 are determined by the solubility limit of telomers in THF.     

Quasiliving Carbocationic Polymerization. II. The Discovery: The α-Methylstyrene System

A detailed analysis of elementary reactions of carbocationic polymerization culminated in the prediction and subsequent experimental demonstration of quasiliving polymerization. Quasiliving polymers are formed in a system provided that the process of chain termination and chain transfer to monomer are absent or reversible, i.e., the propagating ability of the chain end is maintained throughout the experiment, and the molecular weight increases in proportion to the cumulative amount of monomer added. The chain end can be active (carbocation) or dormant (reactivable polymeric olefin or cation source). Chain transfer is suppressed by keeping the monomer concentration low. Quasiliving polymerizations are maintained by continuous slow feeding of dilute monomer to a charge containing the initiating or propagating species (quasiliving polymerization technique). A comprehensive kinetic scheme has been developed that describes quasiliving polymerization in quantitative terms. Quasiliving polymerization was demonstrated experimentally in the “H₂O”/BCl₃/α-methylstyrene and cumyl chloride/BCl₃/α-methylstyrene systems. M _n versus monomer input plots are linear over wide ranges, indicating quasiliving conditions, and poly(α-methylstyrenes) with M _n > 2 × 10⁵ have been obtained, Molecular weight distributions were found progressively to narrow and dispersion ratios M _w/M _n to decrease.     

Living Carbocationic Copolymerizations. V. Synthesis of Isobutylene/p-Methylstyrene Copolymers with the Constant Copolymer Composition Technique in the Leidenfrost Reactor

Abstract

Living copolymerization of the isobutylene (IB)-p-methylstyrene (pMeSt) monomer pair in combination with the constant copolymer composition (CCC) technique produces high molecular weight ( M _n ≈ 100,000 g·mol^?1) and narrow molecular weight distribution ( M _w/ M _n ≈ 1.45) compositionally uniform IB/pMeSt copolymer molecules in the industrially important IB/pMeSt = 97–99/3–1 mol% composition range. Syntheses were carried out with TiCl₄ coinitiator in n-butyl chloride homogeneous solution at ?85°C by the use of the Leidenfrost reactor (i.e., by direct cooling of the charge with liquid nitrogen). In order to carry out the CCC technique it was necessary to obtain reliable copolymerization reactivity ratios. These investigations led to r_IB = 0.5 ± 0.1 and r _pMeSt = 10 ± 4. The attainment of CCC and living copolymerization conditions has been quantitatively demonstrated by dedicated diagnostic plots. Specifically, the attainment of CCC conditions was proven by the analysis of composite rate plots (comonomers input and corresponding copolymer formed versus time) and composition plots (comonomer composition in feed and copolymer formed versus weight of copolymer formed, W _p), and living copolymerization was proven by linearly ascending number-average molecular weight of copolymer ( M _n) versus W _p plots starting at the origin.     

Living Carbocationic Polymerization. XXIII. Analysis of Slow Initiation in Living Isobutylene Polymerization

The aim of this research was to develop a quantitative treatment of the consequences of relatively slow initiation on M _n and N (the number of molecules formed, W_p/M _n , where W_p =weight of polymer formed) in living carbocationic polymerizations, particularly for the case of the incremental monomer addition (IMA) technique. This has been achieved by analysis of the effect of initiator efficiency (I_eff (%) = 100N/[I ₀], where [I ₀] = initiator input) on M _n versus W_p , and N versus W_p plots. Three types of systems have been discerned: 1) I_eff equal to 100%; 2) I_eff constant but less than 100%; and 3) I_eff less than 100% but increasing with increasing number of monomer increments j by the IMA technique. Thus conditions can be found under which slowly initiating systems yield close to “ideal” product, i.e., one with M _n = [M₀ ]/[I₀ ] and narrow molecular weight distribution (M _w /M _n ≈ 1.1). The corresponding equations and plots can be used to diagnose the mechanism. Subsequently, this quantitative analysis was used to describe a novel living system, trans‐2,5‐diacetoxy‐2,5‐dimethyl‐3‐hexene (DiOAcDMH₆)/BCI₃/isobutylene/CH₃CI. This system produces linear t‐chlorine‐telechelic polyisobutylenes under homogeneous conditions. Surprisingly, cationation seems to be rate determining. This conclusion is illustrated by chemical equations.     

Influence of heavy metals on the early hydration of calcium sulfoaluminate

The hydration of calcium sulfoaluminate $ ( {\text{C}}_{4} {\text{A}}_{3} \overline{\text{S}} ) $ in the presence of heavy metal is essential not only for applying the cement in solidification/stabilization (s/s) process, but also for preparing modern green cements from wastes containing heavy metals. In this study, the influence of gypsum, types, and concentrations of heavy metal nitrates (Pb(NO₃)₂, Cr(NO₃)₃·9H₂O, Cu(NO₃)₂·3H₂O, Zn(NO₃)₂·6H₂O) on the hydration of $ {\text{C}}_{4} {\text{A}}_{3} \overline{\text{S}} $ during the first 24 h were investigated by isothermal conduction calorimetry, X-ray diffraction, and thermogravimetric analysis. The addition of 20 % of gypsum to $ {\text{C}}_{4} {\text{A}}_{3} \overline{\text{S}} $ leads to a rapid formation of ettringite against monosulfate and acceleration of hydration. The effects of heavy metals on the hydration of $ {\text{C}}_{4} {\text{A}}_{3} \overline{\text{S}} $ depend on the types of heavy metals and the addition of gypsum. Without any gypsum addition, heavy metal nitrates such as Cr, Cu, and Zn promote the hydration of $ {\text{C}}_{4} {\text{A}}_{3} \overline{\text{S}} $ , whereas Pb presents a strong retardation effect at the early age of $ {\text{C}}_{4} {\text{A}}_{3} \overline{\text{S}} $ hydration. When 20 % of gypsum is added to $ {\text{C}}_{4} {\text{A}}_{3} \overline{\text{S}} $ , heavy metals tend to accelerate the hydration of the blended pastes except Zn. However, heavy metal containing phases were not detected in this work, which needs to be supplemented by further investigations.     

REACTIONS OF SULFUR DIOXIDE WITH AMINOPHOSPHINES

Abstract

The reactions of SO₂ with tris-dimethylaminophosphine, bis-dimethylaminofluorophosphine, bis-dimethylaminochlorophosphine, dimethylaminodifluorophosphine, dimethylaminodichlorophosphine, 1,3-dimethyl-2-fluoro-1,3,2-diazaphospholidine and 1,3-dimethyl-2-chloro-1,3,2-diazaphospholidine have been investigated. The complex reactions are dominated by facile oxidation of the respective phosphine to phosphoryl and thiophosphoryl derivatives. The new heterocyclic phosphines CH₃ NCH₂CH₂N(CH₃)P(O)F and CH₃ NCH₂CH₂N(CH₃)P(S)F have been isolated and characterized by NMR, infrared, and mass spectrometry.     

A photoionization study of the ion-neutral complexes CH3CH +CH 3 · CH2CH3] and CH3CH2CH+CH 3 · CH3 in the gas phase: Formation,H-transfer and C—C bond formation between partners,and channeling of energy into dissociation

Photoionization mass spectrometry was used to investigate the dynamics of ion-neutral complex-mediated dissociations of the n-pentane ion (1). Reinterpretation of previous data demonstrates that a fraction of ions 1 isomerizes to the 2-methylbutane ion (2) through the complex CH₃CH⁺CH ₃ ^· CH₂CH₃ (3), but not through CH₃CH⁺CH₂CH ₃ ^· CH₃ (4). The appearance energy for C₃Hin ₇ ⁺ formation from 1 is 66 kJ mol^?1 below that expected for the formation of n-C₃H ₇ ⁺ and just above that expected for formation of i-C₃H ₇ ⁺ . This demonstrates that the H shift that isomerizes C₃H ₇ ⁺ is synchronized with bond cleavage at the threshold for dissociation to that product. It is suggested that ions that contain n-alkyl chains generally dissociate directly to more stable rearranged carbenium ions. Ethane elimination from 3 is estimated to be about seven times more frequent than is C-C bond formation between the partners in that complex to form 2, which demonstrates a substantial preference in 3 for H abstraction over C-C bond formation. In 1 → CH₃CH⁺CH₂CH₃ + CH₃ by direct cleavage of the C1–C2 bond, the fragments part rapidly enough to prevent any reaction between them. However, 1 → 2 → 4 → C4H ₈ ⁺ + CH₄ occurs in this same energy range. Thus some of the potential energy made available by the isomerization of n-C₄H₉ in 1 is specifically channeled into the coordinate for dissociation. In contrast, analogous formation of 3 by 1 → 3 is predominantly followed by reaction between the electrostatically bound partners.     

The thermodynamic properties and solvation of ammonium bromide,iodide, and nitrate in methylpyrrolidone at 298.15 K

The heat capacity and density of solutions of ammonium bromide, iodide, and nitrate in methylpyrrolidone (MP) were studied calorimetrically and densimetrically at 298.15 K. The standard partial molar heat capacities and volumes (\(\overline {C_{p_2 }^O } \) and \(\overline {V_2^O } \)) of the electrolytes in MP were calculated. The standard heat capacities \(\overline {C_{p_i }^O } \) and volumes \(\overline {V_i^O } \) of the nitrate and ammonium ions in MP were determined. The mean coordination numbers of the NH ₄ ⁺ and NO ₃ ^? ions in a solution in MP at 298.15 K were calculated.     

Synthesis and Characterization of Styrene-Isoprene Diblock Copolymers

A simple reusable apparatus for the synthesis of up to 40 g quantities of poly(styrene-b-isoprene) diblock copolymers of reasonably low (1.2 to 1.5) polydispersity has been described. The diblock copolymers synthesized were characterized by gel permeation chromatography (GPC), membrane osmometry, viscosimetry, and nuclear magnetic resonance (NMR) spectroscopy. Number-average molecular weights (M _n) calculated from the raw GPC chromatographs of the diblock copolymers using the summation method and M versus elution volume plots for polystyrene and polyisoprene standards agree well with those measured experimentally with osmometry. It is suggested that for polydisperse block copolymers this method is simpler than the use of a universal calibration curve. Mark-Houwink constants K ans a for polyisoprene having 18% (1,2-), 66% (3,4-), and 16% (1,4-) microstructure were found to be 3.2 × 10^?4 dL/g and 0.67, respectively, in THF at 25°C. In toluene at 30°C, K = 2.0 × 10^?4 dL/g and α = 0.7 were obtained. The diblock copolymers had 26% (1,2-), 60% (3,4-), and 14% (1,4-) microstructure in the isoprene segments, and the values of K and a for these copolymers (PS > 50%, M 20.0 × 10³) in THF at 25°C were 9.0 × 10^?5 dL/g and 0.75. For M < 20.0 × 10³ the value of α was 0.5. The experimental values of [η] were found to be lower than those calculated theoretically, presumably due to the polydisperse nature and the biellipsoidal configuration of the diblock copolymers.