Fluorocyclopropanes. IV. Copolymers of perfluorocyclopropene

Perfluorocyclopropene undergoes free-radical copolymerization with ethylene, isobutylene, cis- and trans-2-butene, vinyl acetate, methyl vinyl ether, vinyl chloride, styrene, acrylonitrile, tetrafluoroethylene, vinyl fluoride, and vinylidene fluoride. The copolymerization proceeds most readily with electron-rich olefins such as methyl vinyl ether (to yield a 1:1 copolymer), but conditions were found to give copolymers with electron-deficient olefins such as tetrafluoroethylene and vinylidene fluoride. Copolymers with methyl vinyl ether, tetrafluoroethylene, vinyl fluoride, and vinylidene fluoride were examined in detail. Evidence is presented that the perfluorocycloproply ring is incorporated intact into the copolymer and can be subsequently isomerized to a perfluoropropenyl unit by heating at 200–300°C.     

Dielectric Relaxations in Plasma-Polymerized Hydrocarbons and Fluorocarbons

The dielectric behavior of plasma-polymerized ethylene (PPE), ethylene/acetylene (PPEA), ethane/vinyl chloride (PPEVC) and tetrafluoroethylene (PPTFE) was studied over a frequency range of 10² to 10⁵ Hz between -150 and 100°C. After exposure to the atmosphere, each of the polymers exhibited a pronounced loss peak. This relaxation process was designated as the γ_pprocess, and was attributed to the local mode motion of several molecular segments. The average activation energy for all four polymers was found to be 13.8 kcal/mole. It was proposed that oxidation introduces carbonyl groups into the nonpolar polymer chain. The added polar carbonyl groups then act as tracers to render the molecular motions observable by dielectric measurements. The presence of these carbonyl groups was confirmed by concomitant IR spectroscopic determinations. Comparison of the experimental data with the Kirkwood-Froelich theory was found to be satisfactory.     

等离子体聚四氟乙烯的ESR研究

目前,对等离子体聚合机理,即自由基和离子聚合机理仍在争论之中^[1-6],ESR的研究对探讨等离子体聚四氟乙烯(PPTFE)聚合机理将是有价值的。     

Relative rates for plasma homo- and copolymerizations of olefins in a homologous series of fluorinated ethylenes

It is well known that the rate of plasma polymerization, or deposition rate, of a given monomer depends on various plasma process parameters, e.g., monomer flow rate, pressure, power, frequency (DC, rf or microwave), location of the substrate in the reactor, reactor geometry or configuration, and temperature. In contrast, little work has been done to relate deposition rates to monomer structures for a homologous series of monomers where the rates are obtained under identical plasma process parameters. For the particular series of fluorinated ethylenes (C2HxF4-x; x = 0-4), deposition rates were reported for ethylene (ET), vinyl fluoride, vinylidene fluoride and tetrafluoroethylene (TFE), but for plasma polymerizations carried out under different discharge conditions, e.g., pressure, current density, and electrode temperature. Apparently, relative deposition rates were reported for only two members of that series (ET, x = 4, and TFE, x = 0) for which the plasma polymerizations were conducted under identical conditions. We now present relative deposition rates for both homopolymerizations and copolymerizations of the entire series of fluorinated ethylenes (x = 0-4). Our interest in such rates stems from prior work on the plasma copolymerization of ET and TFE in which it was found that the deposition rates for the plasma copolymers, when plotted versus mol % TFE in the ET/TFE feed stock, followed a concave-downward curve situated above the straight line joining the deposition rates for the plasma homopolymers. This type of plot (observed also for an argon-ET/TFE plasma copolymerization) indicated a positive interaction between ET and TFE such that each monomer apparently "sensitized" the plasma copolymerization of the other. Since the shape of that plot is not altered if mol % TFE is replaced by F/C, the fluorine-to-carbon ratio, this paper aims (1) to show how the relative deposition rates for plasma copolymers drawn from all pairs of monomers in the C2HxF4-x series, as well as the deposition rates for the individual plasma homopolymers, vary with F/C ratios of the monomers or monomer blends, and (2) to see if those rates give rise to a common plot.     

Sorption and swelling of semicrystalline polymers in supercritical CO2

The equilibrium sorption and swelling behavior of four different polymers—poly(methyl methacrylate), poly(tetrafluoroethylene), poly(vinylidene fluoride), and the random copolymer tetrafluoroethylene–perfluoromethylvinylether–in supercritical CO₂—are studied at different temperatures (from 40 to 80 °C) and pressures (up to 200 bar). Swelling is measured by visualization, and sorption through a gravimetric technique. From these data, the behavior of amorphous and semicrystalline polymers can be compared, particularly in terms of partial molar volume of CO₂ in the polymer matrix. Both poly(methyl methacrylate) and the copolymer of tetrafluoroethylene exhibit a behavior typical of rubbery systems. On the contrary, polymers with a considerable degree of crystallinity, such as poly(tetrafluoroethylene) and poly (vinylidene fluoride), show larger values of partial molar volume. These can be related to the limited mobility of the polymer chains in a semicrystalline matrix, which causes the structure to “freeze” during the sorption process into a nonequilibrium state that can differ significantly from the actual thermodynamic equilibrium. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1531–1546, 2006     

Chemical Investigation on Various Aromatic Compounds Polymerization in Low Pressure Helium Plasma

Remarkable properties of plasma polymer films are greatly dependent not only on the chemical structure of precursor but also on the reactor design and the deposition conditions. In many industrial applications it is a challenge to control the plasma polymer structure. In this paper we investigate the chemical transformation of various aromatic compounds, such as activation and fragmentation of substituent-part, aromatic ring opening, during plasma polymerization process. Polymerized films are deposited in a low-frequency capacitively coupled plasma-enhanced chemical vapour deposition reactor, working at low pressure. The chemical composition of plasma-polymerized films is elucidated by Fourier-transform infrared spectroscopy, solid-state carbon-13 nuclear magnetic resonance spectroscopy, and X-ray photoelectron spectroscopy. Based on spectroscopic measurements, the intermediary reactions during film growth may be presumed.     

Electron donor–acceptor properties of thin polymer films on silicon. II. Tetrafluoroethylene polymerized by RF glow discharge techniques

Metal–insulator–semiconductor (MIS) techniques were used to show that 86–210 nm thick plasma-polymerized tetrafluoroethylene films on silicon stored only negative charge (electron acceptors). This property persisted at a reduced level when a 7 nm thick inner layer of hydrolyzed γ-aminopropyltriethoxysilane was combined with an outer layer of plasma-polymerized tetrafluoroethylene. The dispersion force contribution to the surface energy, γ^d_s, for the fluorocarbon films was found to be 6 mJ/m² (erg/cm²) which is comparable with the lowest values found in the literature. X-ray photoelectron spectroscopy (XPS) revealed a substantial content of ? CF₃ groups in the fluorocarbon films. This finding coupled with the reported effects of noncrystallinity, crosslinking, and branching on the surface energies of fluorocarbon systems were used to explain the low surface energy and electrophilicity of the plasma-deposited poly(tetrafluoroethylene)s.     

Polymethacrylate polymers with appended aluminum(III)-tetraphenylporphyrins: Synthesis, characterization and evaluation as macromolecular ionophores for electrochemical and optical fluoride sensors

The synthesis and characterization of a novel polymethacylate polymer with covalently linked Al(III)-tetraphenylporphyrin (Al(III)-TPP) groups is reported. The new polymer is examined as a potential macromolecular ionophore for the preparation of polymeric membrane-based potentiometric and optical fluoride selective sensors. To prepare the polymer, an Al(III) porphyrin monomer modified with a methacrylate functionality is synthesized, allowing insertion into a polymethacrylate block copolymer (methyl methacrylate and decyl methacrylate) backbone. The resulting polymer can then be incorporated, along with appropriate additives, into conventional plasticized poly(vinyl chloride) films for testing electrochemical and optical fluoride response properties. The covalent attachment of the Al(III)-TPP ionophore to the copolymer matrix provides potentiometric sensors that exhibit significant selectivity for fluoride ion with extended lifetimes (compared to ion-selective membrane electrodes formulated with conventional free Al(III)-TPP structure). However, quite surprisingly, the attachment of the ionophore to the polymer does not eliminate the interaction of Al(III)-TPP structures to form dimeric species within the membrane phase in the presence of fluoride ion. Such interactions are confirmed by UV/visible spectroscopy of the blended polymeric films. Use of the new polymer-Al(III)-TPP conjugates to prepare optical fluoride sensors by co-incorporating a lipophilic pH indicator (4′,5′-dibromofluorescein octadecyl ester; ETH7075) is also examined and the resulting optical sensing films are shown to exhibit excellent selectivity for fluoride, with the potential for prolonged operational lifetime.     

Organophosphorus chemistry. Part 21 [1]. Insertion of olefins into P  CF3 bonds

Tris(trifluoromethyl)phosphine and ethylene reacted efficiently under u.v. irradiation to give 3,3,3-trifluoropropylbis(trifuomothyl) phosphine in good yield. With vinyl fluoride, vinylidene fluoride, and propene the reaction was regioselective rather than regiospecific, and the yield of 1:1 adduct was low. In these reactions, and in those with vinyl chloride, but-1-ene, and hexafluoropropene, in which only traces of 1:1-adduct could be detected, the bulk of the olefin and of the phosphine was recovered, and numerous by-products consistent with radical intermediates were identified. With propyne, 1,1,1-trifluoro-3-bis(trifluoromethyl)phosphino-cis-but-2-ene was obtained in moderate yield, but no reaction occurred between the phosphine and either but-2-yne or hexafluorcbut-2-yne. Tris(trifluoromethyl)phosphine oxide did not form an adduct with ethylene, tetrafluoroethylene, or propyne.Bis(trifluoromethyl)phosphine and dimethylphosphine both reacted readily under u.v. irradiation with 3,3,3-trifluoropropene, the phosphinyl radical attacking the terminal carbon in each case.     

Fluoride ions at the Cu–fluoropolymer interface

Nanometer thick films of sputtered and evaporated Cu were deposited on the surfaces of the fluoropolymers poly(tetrafluoroethylene) (PTFE), poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) and poly(tetrafluoroethylene‐co‐perfluoropropyl vinyl ether) (PFA) and studied by both angle‐resolved XPS at takeoff angles of 10°, 45° and 80° and in situ argon ion etching. Higher yields of the fluoride ion to fluoropolymer ratio were detected for sputtered than evaporated Cu. PFA and FEP show enhanced interaction with sputtered Cu to produce fluoride ions relative to the more polycrystalline PTFE. At intermediate depths (takeoff angle of 45°), PFA and FEP exhibit the strongest fluoride F 1s signals compared with the fluoropolymer peaks. The amount of fluoride ion detected reaches a maximum after brief Ar ion etching and then decreases with prolonged etching. Compared with untreated fluoropolymers, improved adhesion of evaporated Cu was observed on the fluoropolymer surfaces that were argon ion etched to expose fluoride ions. Copyright © 2013 John Wiley & Sons, Ltd.     

Control of attachment of bovine serum albumin to pulse plasma-polymerized maleic anhydride by variation of pulse conditions

This letter describes how the irreversible attachment of bovine serum albumin (BSA) to films of plasma-polymerized maleic anhydride can be measured by an indirect antibody-binding assay and how this attachment appears to be strongly affected by the polymerization conditions. Surface plasmon resonance (SPR) was used to follow the binding of the antibody, anti-bovine serum albumin (aBSA), to protein-modified plasma-polymerized maleic anhydride films. It was found that BSA could be irreversibly bound to polymers made under pulse plasma conditions, but BSA did not bind to polymers made under continuous wave conditions. Moreover, the degree of antibody binding, which is directly related to the quantity of BSA on the polymer, correlated with the plasma duty cycle (t(on)/t(on) + t(off)): lower duty cycle pulse plasma conditions gave greater BSA attachment. We speculate that BSA is being covalently bound to the polymer via the reaction of amine groups on lysine residues in BSA with the retained anhydride group functionality in the polymer.     

Some aspects of plasma polymerization of fluorine-containing organic compounds. II. Comparison of ethylene and tetrafluoroethylene

Plasma polymerizations of ethylene and tetrafluoroethylene are compared. In the plasma polymerization of ethylene and of tetrafluoroethylene, glow characteristics play an important role. Glow characteristic is dependent on a combined factor of W/F_m, where W is discharge power and F_m is monomer flow rate. At higher flow rates, higher wattages are required to maintain “full glow.” In the plasma polymerization of tetrafluoroethylene, simultaneous decomposition of the monomer competes with plasma polymerization. Above a certain value of W/F_m, decomposition becomes the predominant reaction, and the polymer deposition rate decreases with increasing discharge power. ESCA results indicate that the plasma polymer of tetrafluoroethylene that is formed in an incomplete glow region (low W/F_m) is a hybrid of polymers of plasma polymerization and of plasma-induced polymerization of the monomer. Polymers formed under conditions of high W/F_m to produce “full glow” are similar, regardless of the extent of decomposition of the monomer. They contain carbons with different numbers of F(CF₃, ? CF₂? , >CF? , >C<) and carbons bonded to other more electronegative substituents.     

Cyclopropane chemistry. Part 5 [1,2]. Hexafluorocyclopropane as a source of difluorocarbene

Thermolysis of hexafluorocyclopropane in the presence of ethylene, propene, vinyl chloride, and vinyl bromide gives good yields of the corresponding 1,1-difluorocyclopropanes, formed by addition of difluorocarbene to the olefin. The tetrafluoroethylene formed dimerises to octafluorocyclobutane, co-dimerises with the olefin, or survives, depending on the reaction conditions. With allene, hexafluorocyclopropane gives 1-(difluoromethylene)cyclopropane, 2,2,3,3-tetrafluorospiropentane, and products derived from tetrafluoroethylene and allene.     

Correlation of thermal degradation mechanisms: Polyacetylene and vinyl and vinylidene polymers

The thermal degradation of poly(vinyl bromide) (PVB), poly(vinyl chloride) (PVC), poly(vinyl alcohol) (PVA), poly(vinyl acetate) (PVAc), poly(vinyl fluoride) (PVF), poly(vinylidene chloride) (PVC₂), and poly(vinylidene fluoride) (PVF₂) has been studied by direct pyrolysis–mass spectrometry (DP-MS) and flash pyrolysis–gas chromatography–mass spectrometry techniques. Vinyl and vinylidene polymers exhibit two competitive thermal degradation processes: (1) HX elimination with formation of polyene sequences which undergo further moleculaar rearrangements, and (2) main-chain cleavage with formation of halogenated or oxigenated compounds. The overall thermal degradation process depends on the prevailing decomposition reaction in each polymer; therefore, different behaviors are observed. The thermal degradation of polyacetylene (PA) has also been studied and found important for the elucidation of the thermal decomposition mechanism of the title polymers.     

Polymer particle formation in suspension polymerization of vinyl chloride and vinyl acetate

Equipment has been designed and assembled in such a way that direct microscopic observation of polymer particle formation in suspension polymerization of vinyl chloride and vinyl acetate is possible. The apparent mode of transformation from monomer droplets into polymer particles has thus been studied under two sets of conditions: (1) with agitation and (2) without agitation. In both cases, as the initial vinyl acetate/vinyl chloride ratio was raised, the apparent change in the shape and transparency of particles occurring during the course of polymerization became less evident. In vinyl chloride homopolymerization and vinyl acetate–vinyl chloride copolymerization with relatively high vinyl chloride concentrations, the polymer particles burst during the course of polymerization. Some factors which affect the change in the size of particles are also discussed.     

Plasma polymerization of some organic compounds and properties of the polymers

Plasma polymerizations (under 13.5-MHz radiofrequency inductively coupled glow discharge) of some organic compounds are investigated by their properties (elemental analysis, surface energy, and infrared spectra) and their relations to the concentrations of free radicals in the polymers as detected by electron spin resonance (ESR) spectroscopy. Monomers that have been investigated are hexamethyldisiloxane, tetrafluoroethylene, acetylene, acetylene/N₂, acetylene/H₂O, acetylene/N₂/H₂O, allene, allene/N₂, allene/H₂O, allene/N₂/H₂O, ethylene, ethylene/N₂, ethylene oxide, propylamine, allylamine, propionitrile, and acrylonitrile. Plasma-polymerized polymers generally contain oxygen, even if the starting monomers do not contain oxygen. This oxygen incorporation is related to the free-radical concentration in the polymer. Molecular nitrogen copolymerizes with other organic monomers such as acetylene, allene, and ethylene, and their properties are very similar to those of plasma-polymerized polymers from nitrogen-containing compounds such as amines and nitriles. The addition of water to the monomer mixture reduces in a dramatic manner the concentration of free radicals in the polymer and consequently the oxygen-incorporation after the polymer is exposed to air. The concentrations of free radicals (by ESR) are directly correlated to the change of the properties of plasma-polymerized polymers with time of exposure to the atmosphere. These changes are primarily the introduction of carbonyl (and possibly hydroxyl) groups. The addition of water to the plasma introduces these groups during the polymerization.     

PVC photo-oxidative degradation: Identification of volatiles

Volatile products present in poly(vinyl chloride), PVC, after outdoor weathering have been compared with volatiles from laboratory, UV exposed PVC surfaces. Compounds both present in the photo-degraded polymer surface layer and directly emitted from the polymer were measured in the laboratory experiments. The hydrocarbons, oxygenated compounds and chloro-organic species were measured and identified by capillary gas chromatography with a mass spectrometer detector.     

Plasma polymerization of aniline on different surface functionalized substrates

The plasma polymerization of aniline on different surface functionlized low-density polyethylene (LDPE) substrates was investigated, and the resulting polymer was characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and atomic force microscopy. The results showed that the structure of plasma-polymerized polyaniline was rather different from polyaniline synthesized by conventional chemical and electrochemical methods. This difference may be due to extensive coupling reactions and cross-linking reactions during the plasma polymerization process. The use of acrylic acid graft copolymerized LDPE substrate significantly enhanced the adhesion of the polyaniline to the substrate over that observed with pristine LDPE. The plasma polymerized polyaniline can be rendered electrically conductive if the polymerization is carried out on a polystyrenesulfonic acid-coated LDPE substrate. Conductivity can also be induced by acid protonation of the polyaniline by HClO(4). The reaction of the plasma-polymerized polyaniline with viologen grafted on the substrate under UV irradiation and with AuCl(3) and Pd(NO(3))(2) in acid solutions was also investigated.     

Surface Modification of Textile Fibers and Cords by Plasma Polymerization

In this paper we report on the treatment of industrial fibers and cords by means of plasma polymerization techniques. Coatings of plasma-polymerized pyrrole or acetylene were deposited on aramid fibers, aramid cords and polyester cords. The equipment was a custom-built semi-continuous reactor operated on a pulsed DC glow discharge. The fibers and cords were tested for adhesion to various polymers such as tire cord skim stock rubber compounds and epoxy adhesives. Standard industrial pull-out force adhesion measurement techniques were used. The deposition conditions of the plasma polymer films were varied within wide limits. It was found that, in general, films deposited under low-power and high-pressure conditions performed better than films prepared under high-power and low-pressure conditions. For some systems pulsing of the discharge power improved the performance further. For all systems studied, the optimized plasma polymer surface modification outperformed current industrial standards. The plasma-polymerized coatings were characterized by various techniques and the excellent performance results are explained in a tentative model based on the molecular structure of the films. This structure was found to be strongly dependent on the discharge conditions.     

Radiation-induced copolymerization of tetrafluoroethylene with vinyl ethers

Radiation-induced copolymerization of tetrafluoroethylene with various vinyl ethers has been studied. It was found that tetrafluoroethylene can be copolymerized with vinyl ethers to give alternating copolymers over a wide range of the initial monomer concentration in the monomer mixture. The monomer reactivity ratios were determined for the copolymerization of tetrafluoroethylene with n-butyl vinyl ether as 0.005 (r_TFE) and 0.0015 (r_NBVE). The rate of copolymerization is extremely high and has a maximum at an equimolar concentration of two monomers. The alternating structure of the copolymers was confirmed by the analysis of NMR spectra. Some thermal properties of the copolymers were measured by DSC and DTA.