PEGDA/HEMA水凝胶等离子体表面改性的研究

采用紫外光聚合法合成了聚乙二醇双丙烯酸酯(PEGDA)/甲基丙烯酸-2-羟基乙酯(HEMA)复合凝胶,在不同的条件下进行等离子处理后,紫外光下进行表面接枝改性。在凝胶表面引入亲水性基团,改善材料的亲水性。研究了不同等离子体处理条件及辐射条件对丙烯酰胺(AAm)接枝率的影响。研究表明,丙烯酰胺接枝率随着等离子体处理时间的增加先增大后减小,随着紫外光照射时间、丙烯酰胺浓度的增大而增大。     

Graft polymerization of 2-hydroxyethyl methacrylate via ATRP with poly(acrylonitrile-co-p-chloromethyl styrene) as a macroinitiator

Amphiphilic graft copolymers are excellent additives for the development of antifouling membranes by nonsolvent induced phase separation. We report a convenient approach to the synthesis of novel graft copolymers with hydrophobic polyacrylonitrile (PAN) backbones and hydrophilic poly(2-hydroxyethyl methacrylate) (PHEMA) side chains. Atom transfer radical polymerization (ATRP) of 2-hydroxyethyl methacrylate was carried out with poly(acrylonitrile-co-p-chloromethyl styrene) (PAN-co-PCMS) as a macroinitiator in the presence of CuCl/2,2’-bipyridine at 50 °C in dimethyl sulfoxide. Kinetics of the graft polymerization was also evaluated. The synthesis of poly(acrylonitrile-co-p-chloromethyl styrene-g-2-hydroxyethyl methacrylate) (PAN-co-(PCMS-g-PHEMA)) can be relatively controlled when CMS (the ATRP sites) unit in the macroinitiator is around 5 mol%. Both the macroinitiators and graft copolymers were characterized by FTIR, NMR and GPC. The surface morphology and wettability of the copolymer films were studied by AFM and water contact angle measurement, respectively. We demonstrate that phase segregation between the PAN-co-PCMS backbones and the PHEMA side chains takes place and the surface hydrophilicity of the graft copolymers increases with the length of the PHEMA side chains. Because these amphiphilic graft copolymers can be synthesized in mass, they will be useful as latent additives for the fabrication of advanced PAN separation membranes.     

接枝微球PMAA-HEMA/NVP对溶菌酶的吸附行为与吸附机理

采用反相悬浮聚合法制备了甲基丙烯酸羟乙酯(HEMA)与N-乙烯基吡咯烷酮(NVP)的交联共聚微球HEMA/NVP,然后采用"接出"法,实施了甲基丙烯酸(MAA)在交联微球表面的接枝聚合,制得了接枝微球PMAA-HEMA/NVP.以溶菌酶(LYZ)为模型碱性蛋白,深入研究了接枝微球PMAA-HEMA/NVP对碱性蛋白的吸附性能与吸附机理.测定了微球PMAA-HEMA/NVP的zeta电位,考察了PMAA接枝度、介质pH值及离子强度等因素对体系吸附性能的影响.结果表明,在较大的pH范围内,接枝微球PMAA-HEMA/NVP的zeta电位为绝对值较大的负值,即其表面携带有高密度的负电荷.在强静电相互作用的驱动下,接枝微球PMAA-HEMA/NVP对溶菌酶表现出很强的吸附能力.随介质pH值的增高,接枝微球对溶菌酶的吸附容量呈现先增大后减小的变化趋势,在与溶菌酶等电点接近的pH值处(pH=9),具有最大的吸附容量(90mg.g-1);离子强度对接枝微球的吸附能力也有较大的影响,当pH9时,溶菌酶吸附容量随NaCl浓度的增高而减小;当pH9时,吸附容量随NaCl浓度的增高而增大.     

SYNTHESIS OF POLY(METHYL METHACRYLATE)-graft-POLYSTYRENE BY ATOM TRANSFER RADICAL POLYMERIZATION

The radical copolymerization of methyl methacrylate and 2-hydroxyethyl methacrylate was carried out via atomtransfer radical polymerization (ATRP) initiated by ethyl 2-bromoisobutyrate and catalyzed by CuBr/2,2'-bipyridinecomplex. This polymerization proceeds in a living fashion with controlled molecular weight and low polydispersity. Theobtained copolymer was esterified with 2-bromoisobutylryl bromide yielding a macroinitiator, poly(methyl methacrylate-co-2-hydroxyethyl methacrylate-co-2-(2-bromoisobutyryloxy)ethyl methacrylate), and its structure was characterized by ~1H-NMR. This macroinitiator was used for ATRP of styrene to synthesize poly(methyl methacrylate)-graft-polystyrene. Themolecular weight of graft copolymer increased with the monomer conversion, and the polydispersity remained relatively low.The individual grafted polystyrene chains were cleaved from the macroinitiator backbone by hydrolysis and the hydrolyzed product was characterized by ~1H-NMR and GPC.     

有机过氧化物与N,N-二羟烷基对甲苯胺引发体系的研究

<正> 有机过氧化二苯甲酰(BPO)与N,N-二甲基苯胺(DMA)组成的引发体系称为有机氧化还原引发体系.为了提高聚合速度和聚合物的颜色稳定性,发展了BPO-DMT(N,N-二甲基对甲苯胺)引发体系,并已应用于医用高分子的齿科材料和骨水泥中.文献[3]曾简单提到N,N-二2-羟乙基苯胺(DHEA)作为促进剂,其活性与DMA相似;另外BPO可分别与N,N-二(2-羟乙基)对甲苯胺(DHET)和N,N-二(2-羟丙基)对甲苯胺(DHPT)组成引发体系,作为烯类自由基聚合的室温固化剂,但对聚合速度和聚合动力学报道甚少.由于DHPT熔点较高又无刺激味道,因而很适用于自凝齿科林     

Structure changes on polymer blends by means of phase growth on microheterophase surface

We have studied the structural changes on poly(2-hydroxyethyl methacrylate) (PHEMA)/polystyrene (PS) blends by means of phase growth of microheterophase pattern on a template surface composed of poly[2-hydroxyethyl methacrylate (HEMA)-g-styrene (S)] graft copolymer (lamellar shape). The PS macromonomer was synthesized by free radical polymerization of S monomer initiated by a functional initiator [2,2'-azobis(2-(2-imidazolin-2-yl)propane: VA-061] in the presence of a degradative chain transfer agent, followed by an end-capping reaction with p-chloromethylstyrene (CMS). Poly(HEMA-g-S) graft copolymers were prepared by free radical copolymerization of these vinylbenzyl-terminated PS macromonomers with HEMA comonomer.     

Radiation polymerization of acrolein at low temperatures

Radiation polymerization of acrolein in the presence of the additives such as 2-hydroxyethyl methacrylate, acrylic acid, and water at low temperatures (0–78°C) was studied. The polyacrolein resulting from the polymerization gave a small particlelike microsphere (0.5–5 μm in diameter). The rate of the polymerization reaction of acrolein appeared to be accelerated by the addition of a small amount of 2-hydroxyethyl methacrylate or acrylic acid. The particle size of the polyacrolein particle varied with the condition of the polymerization and increased or decreased with an increase in the addition concentration of 2-hydroxyethyl methacrylate or acrylic acid.     

Synthesis and properties of graft copolymers based on poly(3-hydroxybutyrate) macromonomers

Graft copolymers of poly(methyl methacrylate) with poly(3-hydroxybutyrate), PHB, segments as long side chains were prepared by the macromonomer method. PHB macromonomers were prepared from the esterification of oligomers with 2-hydroxyethyl methacrylate at their carboxylic acid end. Esterification products displayed low polydispersity indices (ca. 1.2) and a functionality of over 83%, with a Mn of 2,020. Using free radical polymerization methods, the macromonomers were copolymerized with methyl methacrylate to yield graft (comb type) copolymers at different comonomer feed ratios. The graft copolymers contained from 0.5 to 14 mol-% of PHB blocks, with a glass transition temperature decreasing from 100 to 3 degrees C.     

Fabrication of high-aspect-ratio poly(2-hydroxyethyl methacrylate) brushes patterned on silica surfaces by very-large-scale integration process

We used a novel fabricated process including electron beam and isotropic oxygen plasma to generate signal line patterns of polymerized 2-hydroxyethyl methacrylate (HEMA) on patterned Si(1 0 0) surfaces. Isotropic oxygen plasma was introduced to enhance the resolutions of the line and dots patterns of the PHEMA brush are approached to 350 nm and 2 μm, respectively. We established the surface grafting polymerization kinetics of the PHEMA chains on silicon surface by to fit the thickness and number-average molecular weight (M(n)). The propagation rate (k(p)) and active grafting specie deactivation rate (k(d)) lies in the range of ~3.6 × 10(-2) s(-1) M(-1) and 4.8 × 10(-5) s(-1), respectively. The measured thicknesses by ellipsometer and analyzed M(n) of "free" PHEMA by gel permeation chromatography (GPC) are fitted well by the polymerization kinetic model. In addition, aspect-ratios (height/width) are used to define the shape of patterned PHEMA brushes. The high-aspect-ratio of the PHEMA brush line with width of 350 nm is 0.27. We use a graft polymerization/solvent immersion method for generating various patterns of polymer brushes to investigate the deformation of the PHEMA brush through aspect-ratios.     

Timolol maleate release from pH-sensible poly(2-hydroxyethyl methacrylate-co-methacrylic acid) hydrogels

Multifunctional polymeric materials were obtained from poly(methacrylic acid-co-2-hydroxyethyl methacrylate), to be used as a raw material in the manufacture of contact lens and as drug delivery systems. Poly(methacrylic acid-co-2-hydroxyethyl methacrylate) was prepared by free-radical polymerization in aqueous solution at 60 °C using potassium persulfate (KPS) as initiator and N,N^′-methylenebisacrylamide (BIS) as cross-linker agent. The dynamic and equilibrium swelling properties of dry glassy poly(methacrylic acid-co-2-hydroxyethyl methacrylate) polymeric networks were studied as a function of pH and methacrylic acid (MAA) content. The water content increase as MAA content and pH increase. Timolol maleate delivery from poly(MAA) and poly(2-hydroxyethyl methacrylate) (HEMA) homopolymers was studied and the results show a Fickian diffusion behavior.     

Preparation of poly(4-butyltriphenylamine) particles by chemical oxidative dispersion polymerization

Photoconductive poly(4-butyltriphenylamine) particles were prepared by a chemical oxidative dispersion polymerization. The utilization of statistical copolymer of methyl methacrylate with 2-hydroxyethyl methacrylate (30:70) as a dispersant afforded particles with the narrowest distribution when the other experimental conditions such as the rate of monomer feed, and the dispersant concentration were appropriately selected. Porous particles were obtained at 40 °C using poly(vinyl pyrrolidone) as a dispersant.     

Radiation-induced polymerization of vinyl monomers adsorbed on inorganic substances. VI. Temperature dependence and effects of additives on methyl methacrylate–silica gel system

To elucidate the reaction mechanism of radiation-induced polymerization of methyl methacrylate adsorbed on silica gel, the temperature dependence and effects of acetone and pyridine were investigated. It was found that even at ?78°C the polymerization rate was quite fast. The amounts of high molecular weight GPC peaks of both graft polymers and homopolymers increased with increasing irradiation temperature. The activation energy of the adsorbed state polymerization was low compared with that of bulk polymerization. The low molecular weight peaks of homopolymers decreased with acetone addition but were almost unaffected by pyridine. The low molecular weight peaks of homopolymers were thus polymerized by an anionic mechanism. In the methyl methacrylate–silica gel system both radical and anionic polymerization take place at the same time in formation of graft polymers and homopolymers. A reaction mechanism for the methyl methacrylate–silica gel system was proposed based on the results obtained to date.     

Preparation of micron-size monodisperse poly(2-hydroxyethyl methacrylate) particles by dispersion polymerization

Dispersion polymerization of 2-hydroxyethyl methacrylate using four categories of polymeric stabilizers in a mixture of good and poor solvents was performed to produce polymeric particles. The stabilizers employed were methyl methacrylate and styrene homopolymers, methacryloyl-terminated poly(methyl methacrylate) and polystyrene macromonomers, an amphiphilic poly(methyl methacrylate-co-methacrylic acid-graft-styrene), and polybutadiene derivatives containing reactive vinyl groups. Dispersion copolymerization with a small amount of the macromonomer gave micron-size particles with relatively narrow size distribution. The amphiphilic graft copolymer and the polybutadiene derivatives also afforded monodisperse particles. The mixed ratio between good and poor solvents greatly affected the particle size and size distribution. © 1996 John Wiley & Sons, Inc.     

Laser surface modification of polymers to improve biocompatibility: HEMA grafted PDMS, in vitro assay—III

Polydimethylsiloxane (PDMS) surface modifications were carried out using CO₂-pulsed laser, without photosensitizer at ambient condition, to introduce peroxide groups onto the PDMS surface. Such peroxides were capable of initiating graft polymerization of 2-hydroxyethyl methacrylate (HEMA) onto the PDMS. The modified surfaces were characterized using a variety of techniques including scanning electron microscopy (SEM), attenuated total reflectance infrared (ATR-FTIR) and the water drop contact angle measurements. Data from in vitro assays indicated a significant reduction of the platelet adhesion and aggregation for the modified surfaces.     

Hydrogels obtained by radiation-induced polymerization as delivery systems for peptide and protein drugs

The controlled release of peptides and proteins from hydrogels obtained by radiation-induced polymerization of 2-hydroxyethyl methacrylate at a low temperature was studied. It was found that the extent of release progressively decreased as protein molecular weight increased until no further release occurred above a critical value of the latter. However, an increasing rate of protein release was found if the polymerization was carried out in the presence of poly(ethylene glycol), PEG. Moreover, only with high molecular weight PEGs were large proteins released. The release data as a function of swellability and porosity of polymer matrices were discussed.     

原子转移自由基聚合法合成大豆分离蛋白-g-聚甲基丙烯酸2-羟乙酯

通过酰胺化反应在大豆分离蛋白(SPI)表面引入溴原子,合成了大分子引发剂SPI-Br,以CuCl和bpy为催化体系,通过原子转移自由基聚合法(ATRP)合成了大豆分离蛋白-g-聚甲基丙烯酸2-羟乙酯(SPI-g-PHEMA).用FTIR1、3C-NMR、GPC对大分子引发剂、接枝产物和接枝物降解链进行结构表征.结果表明,得到了表面接枝聚甲基丙烯酸2-羟乙酯长链的大豆分离蛋白接枝聚合物,用紫外分光光度计(UV)、荧光分光光度计z、eta电位和透射电镜(TEM)表征了接枝产物的溶液性质和微观形态.     

Estimation of heterogeneous surface structure of submicron-sized,composite polymer particles consisting of hydrophobic and hydrophilic components by atomic force microscopy*

Surface structure of submicron-sized poly(styrene/2-hydroxyethyl methacrylate) [P(S/HEMA)] composite particles produced by emulsifier-free emulsion polymerization was estimated with atomic force microscopy (AFM). AFM force curves were measured in water at different points of the particle surface; it was clarified that the particle surface had a heterogeneous structure consisting of hard and soft parts, which must be, respectively, based on styrene-rich and 2-hydroxyethyl methacrylate-rich parts.     

磷酰胆碱色谱固定相的制备及其在分离生物大分子中的应用

以三氯氧磷、氯化胆碱和甲基丙烯酸-2-羟乙酯(HEMA)为原料合成了含磷酰胆碱的单体2-甲基丙烯酰氧乙基磷酰胆碱(MPC). 在硅胶表面嫁接聚合MPC, 得到磷酰胆碱两性离子交换色谱填料. 研究了该填料对标准蛋白的分离性能及pH对蛋白质保留的影响. 结果表明, 该填料对溶菌酶和牛血清白蛋白的动态吸附容量分别为13.8和18.7 mg/g, 其基质磷酰胆碱色谱固定相可同时基线分离两种酸性和两种碱性蛋白.     

Living radical polymerizations with germanium, tin, and phosphorus catalysts--reversible chain transfer catalyzed polymerizations (RTCPs)

A novel class of living radical polymerizations with germanium, tin, and phosphorus catalysts were developed. The polymerizations are based on a new reversible activation mechanism, Reversible chain Transfer (RT) catalysis. Low-polydispersity (M(w)/M(n) approximately 1.1-1.3) polystyrene, poly(methyl methacrylate), poly(glycidyl methacrylate), and poly(2-hydroxyethyl methacrylate) with predicted molecular weight were obtained with fairly high conversion in a fairly short time. The pseudo-first-order activation rate constant kact for the styrene/GeI4 (catalyst) system was large enough, even with a small amount of GeI4, explaining why the system provides low-polydispersity polymers from an early stage of polymerization. The retardation in the polymerization rate observed for the styrene/GeI4 system was kinetically proven to be mainly due to the cross-termination between the propagating radical with GeI3*. Attractive features of the germanium, tin, and phosphorus catalysts include their high reactivity hence small amounts (1-10 mM) being required under relatively mild conditions (at 60-100 degrees C), high solubility in organic media without ligands, insensitivity to air hence sample preparation being allowed in the air, and minor color and smell. The germanium and phosphorus catalysts may also be attractive for their low toxicity. The phosphorus catalysts may also be attractive for their low cost.     

Immobilized Enzyme Particles Prepared by Radiation Polymerization of Polyurethane Prepolymer

The immobilization of enzymes such as cellulase by radiation polymerization of dispersed polyurethane prepolymer was studied using tolylene-2,4-diisocyanate and 2-hydroxyethyl methacrylate. The polyurethane particles were obtained by the dispersion of polyurethane prepolymer followed by radiation polymerization, in which the enzyme was immobilized on its surface by convalent bonding. The particle diameter of immobilized enzyme particles varied with monomer concentration and composition. The enzymatic activity of immobilized enzyme particles varied with the temperature of dispersion and irradiation, and decreased with increasing particle diameter.