Preparation of macroporous polyHIPE foams via radiation-induced polymerization at room temperature

PolyHIPEs are highly porous, crosslinked polymer foams typically synthesized within high internal-phase emulsions (HIPEs). Two kinds of polyHIPEs including poly(styrene-divinylbenzene) [P(St-DVB)] and poly(methyl methacrylate-divinylbenzene) [P(MMA-DVB)] foams are synthesized in this work, which are fabricated from HIPEs template via radiation-induced polymerization at room temperature. Traditional free radical polymerization initiated by potassium peroxydisulfate (KPS) at 60 °C for producing polyHIPE P(St-DVB) foams is also conducted for comparison. It is found that the amount of emulsifier can be reduced greatly in the radiation-induced polymerization of HIPEs at room temperature, compared with the traditional polymerization approach. Besides, P(MMA-DVB) PolyHIPE foams with a fine microstructure of highly interconnected pores have been successfully fabricated via radiation-induced polymerization in this work, which is usually difficult to be prepared by thermal-initiation method because of the intermediate hydrophobicity of methyl methacrylate monomer. The influences of the fraction of internal aqueous phase and the concentration of emulsifier on the structure and performance of foams are carefully explored. The structure and compression strength of the foams are characterized by scanning electron microscopy and a mechanical testing machine, respectively.

Fabrication of macroporous foam and microspheres of polystyrene by Pickering emulsion polymerization

Poly(styrene-co-methacrylic acid) (PS-co-MAA) particles were synthesized via surfactant-free emulsion polymerization and then used as particulate emulsifiers for preparation of Pickering emulsions. Our results showed that adjusting the solution pH can tune the wettability of PS-co-MAA particles to stabilize either water-in-oil (W/O) or oil-in-water (O/W) Pickering emulsions. Stable W/O emulsions were obtained with PS-co-MAA particles at low pH values due to their better affinity to the dispersed oil phase. In contrast, increasing the pH value significantly changed the stabilizing behavior of the PS-co-MAA particles, leading to the phase inversion and formation of stable O/W emulsions. We found that the oil/water ratio had a significant influence on pH value of the phase inversion. It decreased with decreasing the oil/water ratio, and no phase inversion occurred when the styrene volume fraction reduced to 10 %. Additionally, macroporous polystyrene (PS) foam and PS microspheres were obtained via polymerization of Pickering high internal phase emulsion (Pickering HIPE) and O/W Pickering emulsion, respectively.     

Wet-spun porous fibers from high internal phase emulsions: Continuous preparation and high stretchability

Although high internal phase emulsion (HIPE)-templating is promising to prepare macroporous materials (polyHIPEs) with controllable shapes and tuneable property, fibrous polyHIPEs with stretchability and their continuous preparation are still challenging. Here, we report the fabrication of polyHIPE fibers in a continuous manner through wet spinning of HIPEs. The successful fabrication of polyHIPE fibers depends on HIPE dispersed phase fractions, ammonia-catalyzed interfacial reaction and wet spinning. Dry polyHIPE fibers exhibit tunable diameters, hierarchically porous structures, high stability to temperature and to various solutions, and high stretchability (with a high tensile strain of 155%), which is hard to achieve for polyHIPEs. The polyHIPE fibers show enhanced uptakes to both water (14.4 ml g⁻¹) and organic solvents (up to 26.3 ml g⁻¹), and the amphiphilic swelling is rare for polyHIPEs. Moreover, the dry polyHIPE fibers show good thermal insulation, similar to that of cotton. Simple wet spinning, combining with HIPEs with tuneable composition, is promising for preparing various polyHIPE fibers for various potential applications.     

Synthesis of Core-Shell Particles of Polystyrene and Poly(methyl methacrylate) Using Emulsion Photopolymerization

Summary: Submicron core-shell particles of polystyrene (PS) and polystyrene-co-poly(methyl methacrylate) (PS-co-PMMA) coated with PMMA were obtained by emulsion photopolymerization. The seeds of PS or PS-co-PMMA were prepared by emulsion polymerization with or without emulsifier and a ratio of functional monomer and crosslinker (SVBS/EDGMA) in order to obtain different surfaces for the subsequent coating with PMMA. At each stage, the evolution of the average particle size were monitored by using photon correlation spectroscopy (DLS) and the final polymer particles was analyzed via transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The core-shell morphology was identified as the increase of the average particle size in the second stage by DLS technique and by the direct observation by TEM of the differentiation between PS core and PMMA shell, and by the presence of two glass transition temperatures (T_g) as a consequence of the existence of two partially miscible phases.     

Acrylic-based high internal phase emulsion polymeric monolith for capillary electrochromatography

The use of high internal phase emulsion polymers (polyHIPEs) for CEC applications has remained relatively unexplored. A few reports exist in the literature for the preparation of similar structures. In this study, polyHIPEs having high porosity, and interconnected open-cell structure, were introduced and evaluated as stationary phase for CEC. The polyHIPE monolithic columns were prepared by the in situ polymerization of isodecylacrylate (IDA) and divinylbenzene (DVB) in the continuous phase of a high internal phase emulsion (HIPE). Due to its well-defined polyHIPE structure with interconnected micron size spherical voids, the columns synthesized with different initiator concentrations were successfully used for the separation of alkylbenzenes. Furthermore, the columns indicated a strong electroosmotic flow (EOF) without any additional EOF generating monomer probably due to the presence of ionizable sulfate groups coming from the water-soluble initiator used in the preparation of polyHIPE matrix. The best chromatographic performance in the separation of alkylbenzenes was achieved by using 70% ACN in the mobile phase with high column efficiency (up to 200 000 plates/m).     

Influence of emulsification process on structure–properties relationship of highly concentrated reverse emulsion-derived materials

Water-in-Oil high internal phase emulsions (HIPEs) whose continuous phase is polymerizable gave access to highly porous polymeric materials (polyHIPEs). These emulsions were prepared with a laboratory-made homogenizer whose shear frequency and time could be varied to study the influence of the emulsification conditions on the polyHIPEs morphology. Intensive and/or long shear induced a reduction of the cell and connection diameters without any modification of the material global porosity. The mechanical properties were evaluated by estimating the Young’s modulus from compression tests. The mechanical behavior was analogous for all materials possessing a characteristic polyHIPE structure, even if cell sizes were different between samples.     

High-internal-phase-emulsion polymeric monolith coupled with liquid chromatography–electrospray tandem mass spectrometry for enrichment and sensitive detection of trace cytokinins in plant samples

High-internal-phase-emulsion polymers (polyHIPEs) show great promise as solid-phase-extraction (SPE) materials because of the tremendous porosity and highly interconnected framework afforded by the high-internal-phase-emulsion (HIPE) technique. In this work, polyHIPE monolithic columns as novel SPE materials were prepared and applied to trace enrichment of cytokinins (CKs) from complex plant samples. The polyHIPE monoliths were synthesized via the in-situ polymerization of the continuous phase of a HIPE containing styrene (STY) and divinylbenzene (DVB) in a stainless column, and revealed highly efficient and selective enrichment ability for aromatic compounds. Under the optimized experimental conditions, a method using a monolithic polyHIPE column combined with liquid chromatography–electrospray tandem mass spectrometry (LC–MS–MS) was developed for the simultaneous extraction and sensitive determination of trans-zeatin (tZ), meta-topolin (mT), kinetin (K), and kinetin riboside (KR). The proposed method had good linearity, with correlation coefficients (R ²) from 0.9957 to 0.9984, and low detection limits (LODs, S/N?=?3) in the range 2.4–47 pg mL^?1 for the four CKs. The method was successfully applied to the determination of CKs in real plant samples, and obtained good recoveries ranging from 68.8 % to 103.0 % and relative standard deviations (RSDs) lower than 16 %.     

Carbon nanotubes in emulsion‐templated porous polymers: Polymer nanoparticles,sulfonation, and conductivity

Sulfonated polymers are of interest for ion exchange resins, reaction supports, and membranes for separation, filtration, fuel cells, and electrochemical devices. Sulfonic groups have been introduced into polystyrene (PS) through exposure to sulfuric acid, and carbon nanotubes (CNTs) have been added to polymers to enhance proton conductivity without creating an electronic percolation pathway. PolyHIPEs, emulsion‐templated porous polymers with highly interconnected hierarchical open‐cell porous structures, are synthesized through polymerization in the external phases of high internal phase emulsions (HIPEs). In this article, the synthesis of PS‐based CNT‐filled polyHIPEs, their structure, sulfonation, and conductivity are described. Adding CNT dispersions to the HIPEs produced polymer nanoparticle–covered polyHIPEs from polymerization within the water‐soluble surfactant micelles in the internal aqueous phase droplets. The CNTs migrated from the HIPE's aqueous phase droplets into the HIPE's organic phase and formed interconnected bundles within the polyHIPE walls, reflecting a reduction in the surfactant's ability to disperse the CNTs. The water adsorption in the hygroscopic sulfonated polyHIPEs increased the conductivity by several orders of magnitude. The conductivity of the sulfonated polyHIPE containing CNTs was more than an order of magnitude greater than that of the sulfonated polyHIPEs with no CNTs. The CNTs act as “bridges,” enhancing the connection between existing conductive pathways. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4369–4377     

Surfactant-free emulsion copolymerization of styrene and methyl methacrylate for preparation of water-redispersible polymeric powders

Poly(methyl methacrylate), polystyrene, and poly(styrene-co-methyl methacrylate) cationically stabilized latexes with up to 25% solid content were prepared by surfactant-free emulsion polymerization (SFEP) employing 1 mol % 2,2′-azobis[2-(2-imidazolin-2-yl)propane]dihydrochloride (VA-044) as an initiator and stabilizer (inisurf) with respect to monomer at 70 °C. The latexes had 200–500 nm z-diameter and a very narrow size distribution (PDI < 0.05). The stabilizing amidinium moieties from VA-044 were covalently bound to the particles. After drying in air, poly(styrene-co-methyl methacrylate), PS-co-PMMA latexes were easily redispersible in water simply by addition of water and a few minutes of gentle stirring. The redispersed latex particles had colloidal characteristics very similar to the original latex particles in terms of polydispersity, size, and zeta potential. In contrast, latexes prepared with a similar formulation but using a conventional cationic surfactant (CTAB) that was not covalently bound to the particles were not redispersible. This is the simplest method reported so far for the preparation of redispersible latexes that do not use high stabilizer concentrations. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2376–2381     

Synthesis and characterization of Fe(II)-coordinated PS-b-P[NIPAM-co-(VBC-Fe-DMAP)] block copolymers

In this work,a new type of block polymers,polystyrene-b-poly[(N-isopropyl acrylamide)-co-(vinyl benzyl chloride)](PS-b-P(NIPAM-co-VBC)),was prepared via reversible addition fragmentation transfer polymerization,then pentacyano(4-(dimethylamino pyridine))ferrate(Fe-DMAP) was attached to VBC units through a quaternization process.The Fe(Ⅱ)-coordinated PS-b-P[NIPAM-co-(VBC-Fe-DMAP)]block copolymers were characterized by ~1H-NMR,FT-IR and TGA.The self-assembly behavior of the block copolymers was also investigated and the micelle morphology was characterized by TEM.It was found that the PS-b-P(NIPAM-co-VBC) block polymer and Fe-coordinated block copolymer could both form spherical micelles in DMF/MeOH mixed solvent.     

Tough interconnected polymerized medium and high internal phase emulsions reinforced by silica particles

Emulsion templating using high internal phase emulsions is an effective route to prepare low density and high porosity macroporous polymers known as polymerized high internal phase emulsions (polyHIPEs). Conventional polyHIPEs, synthesized from surfactant stabilized w/o emulsions have low permeabilities and poor mechanical properties. We present interconnected open macroporous low density nanocomposites produced by polymerizing the continuous phase of emulsion templates, which contained styrene, polyethyleneglycoldimethacrylate, and silylated silica particles. Polyethyleneglycoldimethacrylate and the silylated silica particles acted as crosslinker. The functionalized silica particles were incorporated into the polymer, which resulted in a significant improvement of the mechanical properties of the polyHIPEs without affecting the interconnected and permeable pore structures. The polyHIPEs contained up to 60 wt % silylated silica particles. Young's modulus of the reinforced macroporous polymers increased up to 600% compared with nonreinforced macroporous polymers. The mechanical performance was further increased by increasing the foam density of the macroporous nanocomposites from around 200 to 370 g/cm³ by raising the organic phase volume of the emulsion templates from 20 to 40 vol %. The macroporous polymers synthesized from less concentrated emulsions also possessed interconnected open porous although less permeable structures. The polyHIPE nanocomposites have a permeability of about 200 mD, whereas the polyMIPE nanocomposites still have permeabilities of around 50 mD. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1979–1989, 2010     

The doubly thermo-responsive triblock copolymer nanoparticles prepared through seeded RAFT polymerization

The doubly thermo-responsive triblock copolymer nanoparticles of polystyrene-block-poly(N-isopropylacrylamide)-block-poly[N,N-(dimethylamino) ethyl methacrylate] (PS-b-PNIPAM-b-PDMAEMA) are successfully prepared through the seeded RAFT polymerization in situ by using the PS-b-PNIPAM-TTC diblock copolymer nanoparticles as the seed. The seeded RAFT polymerization undergoes a pseudo-first-order kinetics procedure, and the molecular weight increases with the monomer conversion linearly. The hydrodynamic diameter (D _h) of the triblock copolymer nanoparticles increases with the extension of the PDMAEMA block. In addition, the double thermo-response behavior of the PS-b-PNIPAM-b-PDMAEMA nanoparticles is detected by turbidity analysis, temperature-dependent 1H-NMR analysis, and DLS analysis. The seeded RAFT polymerization is believed as a valid method to prepare triblock copolymer nanoparticles containing two thermo-responsive blocks.     

Adsorption of poly(N-isopropylacrylamide-co-4-vinylpyridine) onto core-shell poly(styrene-co-methylacrylic acid) microspheres

Adsorption of the thermoresponsive copolymer of poly(N-isopropylacrylamide-co-4-vinylpyridine) (PNIPAM-co-P4VP) onto the core-shell microspheres of poly(styrene-co-methylacrylic acid) (PS-co-PMAA) is studied. The core-shell PS-co-PMAA microspheres are synthesized by one-stage soap-free polymerization in water. The copolymer of PNIPAM-co-P4VP is synthesized by free radical polymerization of N-isopropylacrylamide and 4-vinylpyridine in the mixture of DMF and water using K₂S₂O₈ as initiator. Adsorption of PNIPAM-co-P4VP onto the core-shell PS-co-PMAA microspheres results in formation of the composite microspheres of PS/PMAA-P4VP/PNIPAM. The driven force to adsorb the copolymer of P4VP-co-PNIPAM onto the core-shell PS-co-PMAA microspheres is ascribed to hydrogen-bonding and electrostatic affinity between the P4VP and PMAA segments. The resultant composite microspheres of PS/PMAA-P4VP/PNIPAM with surface chains of PNIPAM are thermoresponsive in water and show a cloud-point temperature at about 33 °C.     

丙烯酰胺多面体低聚倍半硅氧烷在超临界CO2中的RAFT聚合

以超临界CO₂为聚合介质, 硫代苯甲酰基特丁基硫酯(TTBT)为链转移剂, 通过可逆加成-断裂链转移(RAFT)聚合制备了聚丙烯酰胺多面体低聚倍半硅氧烷(PAMPOSS)均聚物及其与甲基丙烯酸甲酯(PMMA)的嵌段共聚物(PAMPOSS-b-PMMA). 对产物结构组成和分子量及其分布进行表征. 结果表明, 在TTBT的控制下, POSS的均聚物和嵌段共聚物具有高分子量及窄分子量分布. 含POSS单体在超临界CO₂中为均相聚合, POSS聚合物的结晶性在一定程度上影响其在超临界CO₂中溶解性.     

Synthesis and characterization of polystyrene-b-polyisoprene-b-poly(methylmethacrylate) triblock copolymer

Polystyrene-b-polyisoprene-b-poly(methylmethacrylate) (PS-b-PI-b-PMMA) triblock copolymer was synthesized by sequential anionic polymerization. The as-synthesized triblock copolymer contains side products of inadvertently terminated PS and PS-b-PI precursors. The side products can be effectively removed by semi-prep scale liquid chromatography using multiple injection method to obtain pure PS-b-PI-b-PMMA. It was found that the removed side product contains another polymer species, coupled PS-b-PI, which could not be recognized by size exclusion chromatography (SEC) analysis since the elution peak of the coupled product overlaps with that of PS-b-PI-b-PMMA. This study demonstrates that the size based separation of SEC is often not good enough to characterize complex polymers precisely and interaction chromatography can render unique advantage over SEC analysis.     

Preparation of emulsion‐templated fluorinated polymers and their application in oil/water separation

A series of emulsion‐templated fluorinated polymers (polyHIPEs) were first synthesized with introducing 2‐(perfluorohexyl)ethyl methacrylate (PEM) to the external phase of water‐in‐styrene high internal phase emulsion (HIPE) templates. The morphology (i.e., void size and its distribution) of these porous materials could be tuned simply by changing PEM and/or surfactant amount. The synergistic effect between the surface chemistry and surface architecture allowed the polyHIPEs to possess hydrophobicity with a water contact angle of 151°. The superhydrophobicity and oleophilicity of the polyHIPEs, together with their highly open porous structure, make the material a very competitive candidate as a filtration material for oil/water separation in practice with the efficiency of separating dichloromethane from the oil/water mixture of 95%. Such oil/water separating capacity was maintained after 10 cycles of filtration of oil/water, indicating the cyclic usage of the polyHIPE is feasible. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1508–1515     

Monitoring the formation of polystyrene/silica nanocomposites from vinyl triethoxysilane containing copolymers

Random copolymers of polystyrene-co-polyvinyl triethoxysilane (PS-co-PVTES) were prepared via semi-batch emulsion polymerization with different feed monomer compositions and evaluated as precursors of polystyrene (PS)/silica nanocomposites. Small-angle X-ray scattering (SAXS) profiles acquired from 20 °C to 180 °C showed that, at temperatures higher than glass transition temperature (T _g) of PS, the latex particles aggregate. On thermal annealing at 180 °C, silica-rich domains are formed, as corroborated by scanning electron microscopy. Infrared spectroscopy and differential scanning calorimetry analyses showed a reduction of the silanol concentration and an increase in the T _g value, respectively. The silica long domain spacing, measured by SAXS, depends on the concentration of vinyl triethoxysilane (VTES) in the feed; this value varied from 35 to 57 nm when the weight ratio of the monomers (styrene/VTES) was 50:50 and 90:10, respectively.     

Ionic Liquids as Internal Phase for Non‐Aqueous PolyHIPEs

Stable high internal phase emulsions (HIPEs) with the ionic liquid 1‐ethyl‐3‐methylimidazolium bis(trifluoromethyl‐sulfonyl)imide as dispersed phase were prepared and polymerised thermally into polyHIPEs. All polyHIPEs exhibited pore morphologies similar to that of polyHIPEs obtained with an aqueous dispersed phase. PolyHIPEs containing the dispersed phase possess a low T_g and are thermally stable in excess of 200 °C, offering the potential for new porous materials where water as dispersed phase is chemically or physically undesirable.     

Hybrid foams, colloids and beyond: from design to applications

Highly internal phase emulsion (polyHIPE) materials are promising macrocellular foams bearing versatile applications ranging from catalysis, optics, filtration, insulator and so forth. In this critical review water-in-oil HIPE, oil-in-water HIPE and Pickering-based HIPE are discussed. Also in each above-mentioned HIPE family, declination between the organic, inorganic or hybrid-organic foams chemical nature is proposed. The polyHIPE audience is thereby strongly interdisciplinary in nature crossing boundaries of physical chemistry, colloids, polymer science, sol-gel chemistry, hybrid materials, biology and beyond (114 references).     

Surface structure of thin asymmetric PS-b-PMMA diblock copolymers investigated by atomic force microscopy

Asymmetric poly(styrene-b-methyl methacrylate) (PS-b-PMMA) diblock copolymers of molecular weight M_n = 29,700 g mol⁻¹ (M_PS = 9300 g mol⁻¹M_PMMA = 20,100 g mol⁻¹, PD = 1.15, χ_PS = 0.323, χ_PMMA = 0.677) and M_n = 63,900 g mol⁻¹ (M_PS = 50,500 g mol⁻¹, M_PMMA = 13,400 g mol⁻¹, PD = 1.18, χ_PS = 0.790, χ_PMMA = 0.210) were prepared via reversible addition-fragmentation chain transfer (RAFT) polymerization. Atomic force microscopy (AFM) was used to investigate the surface structure of thin films, prepared by spin-coating the diblock copolymers on a silicon substrate. We show that the nanostructure of the diblock copolymer depends on the molecular weight and volume fraction of the diblock copolymers. We observed a perpendicular lamellar structure for the high molar mass sample and a hexagonal-packed cylindrical patterning for the lower molar mass one. Small-angle X-ray scattering investigation of these samples without annealing did not reveal any ordered structure. Annealing of PS-b-PMMA samples at 160 °C for 24 h led to a change in surface structure.