Fabrication of TiN nanorods by electrospinning and their electrochemical properties

TiN nanorods were synthesized using electrospinning technique followed by thermolysis in different atmospheres. A dimethyl formamide-ethanol solution of poly-(vinyl pyrrolidone) and Ti (IV)-isopropoxide was used as the electrospinning precursor solution and as-spun nanofibers were calcined at 500 °C in air to generate TiO₂ nanofibers. Subsequently, a conversion from TiO₂ nanofibers to TiN nanorods was employed by the nitridation treatment at 600∼1400 °C in ammonia atmosphere. A typical characteristic of the final products was that the pristine nanofibers were cut into nanorods. The conversion from TiO₂ to TiN was realized when the nitridation temperature was above 800 °C. As-prepared nanorods were composed of TiN nano-crystallites and the average crystallite size gradually increased with the increase of the nitridation temperature. Electrochemical properties of TiN nanorods showed strong dependence on the nitridation temperature. The maximum value of the specific capacitance was obtained from the TiN nanorods prepared at 800 °C.     

Thermal annealing synthesis of titanium-dioxide nanowire-nanoparticle hetero-structures

Crystalline TiO₂ nanowire-nanoparticle hetero-structures were successfully synthesized from titanium foils by using a simple thermal annealing method with the aid of CuCl₂ at the atmospheric pressure. Nanowires were grown from Ti foils by simply annealing Ti foils at 850 °C. Then, TiCl₄ was delivered to TiO₂ nanowires so as to precipitate TiO₂ nanoparticles on nanowire surfaces. At 750 °C reaction temperature, nanoparticles of tens of nanometers in diameter were well distributed on pre-grown nanowire forests. Nanoparticles were likely to be precipitated by TiCl₄ decomposition or oxidation and that require high temperatures above ∼650 °C. Electron microscopy, X-ray diffraction, and UV-vis spectroscopy analyses show they have the rutile polycrystalline structure with a slightly enlarged bandgap compared to that of bulk TiO₂. The influence of key synthesis parameters including reaction temperature, reaction time, and quantity of supplied materials on the incorporating nanoparticles was also systematically studied. The optimum reaction condition in the present paper was identified to be 750 °C annealing with repetitive 20 min reactions. A higher reaction temperature yielded larger diameter particles, and higher loading of Ti produced dense particles without changing the particle size. Finally, this method could be utilized for synthesizing other metal oxide nanowires-nanoparticle hetero-structures.     

Syntheses of TiO2(B) nanowires and TiO2 anatase nanowires by hydrothermal and post-heat treatments

TiO₂(B) nanowires and TiO₂ anatase nanowires were synthesized by the hydrothermal processing in 10 M NaOH aq. at 150 °C followed by the post-heat treatment at 300-800 °C. As-synthesized Na-free titanate nanowires (prepared by the hydrothermal treatment and repeated ion exchanging by HCl (aq.) were transformed into TiO₂(B) structure with maintaining 1-D morphology at 300-500 °C, and further transformed into anatase structure at 600-800 °C with keeping 1-D shape. At 900 °C, they transformed into rod-shaped rutile grains. Microstructure of these 1-D TiO₂ nanomaterials is reported.     

Synthesis of titanate, TiO2 (B), and anatase TiO2 nanofibers from natural rutile sand

Titanate nanofibers were synthesized by hydrothermal method (150 °C for 72 h) using natural rutile sand as the starting materials. TiO₂ (B) and anatase TiO₂ (high crystallinity) nanofibers with the diameters of 20-100 nm and the lengths of 10-100 μm were obtained by calcined titanate nanofibers for 4 h at 400 and 700 °C (in air), respectively. The samples characterized by XRD, SEM, TEM, SAED, HRTEM, and BET surface area. This synthesis method provides a simple route to fabricate one-dimensional nanostructured TiO₂ from low cost material.     

Preparation and performances of nanosized Ta2O5 powder photocatalyst

Nanosized-Ta₂O₅ powder photocatalyst was successfully synthesized by using sol-gel method via TaCl₅ butanol solution as a precursor. Ta₂O₅ species can be formed under 500 °C via the decomposition of the precursor. The crystalline phase of Ta₂O₅ powder photocatalyst can be obtained after being calcined above 600 °C for 4 h. The crystal size and particle size of Ta₂O₅ powder photocatalyst was about 50 nm. A good photocatalytic performance for the degradation of gaseous formaldehyde was obtained for the nanosized-Ta₂O₅ powder. The Ta₂O₅ powder formed at 700 °C for 4 h and at 650 °C for 12 h showed the best performance. The calcination temperature and time play an important role in the crystallization and photocatalytical performance of nanosized-Ta₂O₅ powder.     

The synthesis of transition metal nitrides via thermolysis of metal-ammine complexes, Part I: Chromium nitride

The thermal decomposition of a CrN precursor, hexaammine chromium(II) chloride, in ammonia has been investigated via a combination of thermogravimetric analysis, differential thermal analysis, Fourier transform infrared spectroscopy, and X-ray diffraction. Upon heating, [Cr(NH₃)₆]Cl₂ sequentially loses ammonia ligands, ultimately forming CrCl₂·NH₃ at ∼400 °C. When heat-treated to 500 °C in ammonia, this compound ammonolyzes to form nanocrystalline CrN.     

Titania-lanthanum phosphate photoactive and hydrophobic new generation catalyst

Titania-lanthanum phosphate nanocomposites with multifunctional properties have been synthesized by aqueous sol-gel method. The precursor sols with varying TiO₂:LaPO₄ ratios were applied as thin coating on glass substrates in order to be transparent, hydrophobic, photocatalytically active coatings. The phase compositions of the composite powders were identified by powder X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM). The anatase phase of TiO₂ in TiO₂-LaPO₄ composite precursors was found to be stable even on annealing at 800 °C. The glass substrates, coated with TL1 (TiO₂-LaPO₄ composition with 1 mol% LaPO₄) and TL50 (composite precursor containing TiO₂ and LaPO₄ with molar ratio 1:1) sols and annealed at 400 °C, produced contact angles of 74° and 92°, respectively, though it is only 62° for pure TiO₂ coating. The glass substrates, coated with TL50 sol, produced surfaces with relatively high roughness and uneven morphology. The TL1 material, annealed at 800 °C, has shown the highest UV photoactivity with an apparent rate constant, k_app=24×10⁻³ min⁻¹, which is over five times higher than that observed with standard Hombikat UV 100 (k_app=4×10⁻³ min⁻¹). The photoactivity combined with a moderate contact angle (85.3°) shows that this material has a promise as an efficient self-cleaning precursor.     

Synthesis of transparent mixed vanadia/niobia gels and their decomposition to a new metastable VNb9O25 phase

Controlled hydrolysis and condensation of a mixture of vanadyl-tris-n-propoxide, VO(OPr)₃, and niobium pentaethoxide, [Nb(OEt)₅]₂, at 5 °C in propanol yields clear and transparent gels in which the ratio of V:Nb is 1:1, 1:4.5 or 1:9. Oxalic acid and low temperatures are used to slow down the rate of condensation processes. At 800 °C, the thermal decomposition of a gel with the composition 1:9 forms a thermodynamically metastable, new phase of the composition VNb₉O₂₅. At lower temperatures, metastable solid solutions with TT-Nb₂O₅ structure (600 °C) and M-Nb₂O₅ structure (700 °C) are formed from the amorphous xerogel. The new VNb₉O₂₅ phase is structurally related to M-Nb₂O₅. The solid solution with M-Nb₂O₅ structure acts structure directing, leading preferentially to a monoclinic low-temperature form of VNb₉O₂₅. The full transformation of this metastable phase to the well known tetragonal VNb₉O₂₅ requires a annealing temperature of about 1000 °C.     

Preparation and photocatalytic activity of ZnO/TiO2/SnO2 mixture

ZnO/TiO₂/SnO₂ mixture was prepared by mixing its component solid oxides ZnO, TiO₂ and SnO₂ in the molar ratio of 4?1?1, followed by calcining the solid mixture at 200-1300 °C. The products and solid-state reaction process during the calcinations were characterized with powder X-ray diffraction (XRD), thermogravimetric and differential thermal analysis (TG-DTA), UV-Vis diffuse reflectance spectroscopy (UV-Vis DRS) and Brunauer-Emmett-Teller measurement of specific surface area. Neither solid-state reaction nor change of crystal phase composition took place among the ZnO, TiO₂ and SnO₂ powders on the calcinations up to 600 °C. However, formation of the inverse spinel Zn₂TiO₄ and Zn₂SnO₄ was detected at 700-900 and 1100-1200 °C, respectively. Further increase of the calcination temperature enabled the mixture to form a single-phase solid solution Zn₂Ti_0.5Sn_0.5O₄ with an inverse spinel structure in the space group of . The ZnO/TiO₂/SnO₂ mixture was photocatalytically active for the degradation of methyl orange in water; its photocatalytic mass activity was 16.4 times that of SnO₂, 2.0 times that of TiO₂, and 0.92 times that of ZnO after calcination at 500 °C for 2 h. But, the mass activity of the mixture decreased with increasing the calcination temperature at above 700 °C because of the formation of the photoinactive Zn₂TiO₄, Zn₂SnO₄ and Zn₂Ti_0.5Sn_0.5O₄. The sample became completely inert for the photocatalysis after prolonged calcination at 1300 °C (42 h), since all of the active component oxides were reacted to form the solid solution Zn₂Ti_0.5Sn_0.5O₄ with no photocatalytic activity.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

Vapor-thermal preparation of highly crystallized TiO2 powder and its photocatalytic activity

Nanocrystalline anatase TiO₂ powder photocatalysts were synthesized by a vapor-thermal method using tetrabutyl titanate as precursor at a temperature range from 120 to 200 °C. The as-synthesized products were characterized by X-ray diffraction, N₂ adsorption-desorption measurement, transmission electron microscopy, high resolution transmission electron microscopy, Fourier transform infrared spectra, Raman spectra, and their photocatalytic activity was evaluated by photocatalytic oxidation decomposition of acetone in air. The results showed that reaction temperature greatly affected the microstructures and photocatalytic activity of the samples. With increasing reaction temperature and time, the average crystalline size of TiO₂ particles increased and their crystallization enhanced, while the specific surface area of the products decreased. The TiO₂ powders obtained at a temperature range from 150 to 200 °C for 10 h showed good photocatalytic activity and were greatly higher than that of Degussa P-25.     

Structure of TiO2 in TiO2-SiO2 prepared by a complexing agent-assisted sol-gel procedure

Many types of TiO₂-SiO₂ (Ti:Si=50:50 mol%) were prepared by the sol-gel procedure with and without 2-methyl-2, 4-pentanediol (MPD) as an organic ligand. The effect of MPD on the gel structure and the properties of the TiO₂ crystals were studied by XRD and raman spectroscopy, and the effect of the sol standing time on the properties of the TiO₂ crystals were also studied by XRD spectroscopy. In the gels with MPD, anatase of TiO₂ appeared at approximately 580°C, and the crystal structures were similar despite the difference in the gel preparation procedure. The titania gels with MPD were presumed to be dispersed in the silica gel matrix without any Ti-O-Si bond. In the presence of MPD, the formation of titania gels is controlled and the specified TiO₂ crystal is produced.     

Sol–gel synthesis of macro–mesoporous titania monoliths and their applications to chromatographic separation media for organophosphate compounds

We have developed a method of independently tailoring the macro- and mesoporous structures in titania (TiO₂) monoliths in order to achieve liquid chromatographic separations of phosphorous-containing compounds. Anatase TiO₂ monolithic gels with well-defined bicontinuous macropores and microstructured skeletons are obtained via the sol–gel process in strongly acidic conditions using poly(ethylene oxide) as a phase separator and N-methylformamide as a proton scavenger. Aging treatment of the wet gels in the mother liquor at temperatures of 100–200 °C and subsequent heat treatment at 400 °C allow the formation and control of mesoporous structures with uniform pore size distributions in the gel skeletons, without disturbing the preformed macroporous morphology. The monolithic TiO₂ rod columns with bimodal macro–mesoporous structures possess the phospho-sensitivity and exhibit excellent chromatographic separations of phosphorus-containing compounds.     

Effects of synthesis parameters on the microstructure and phase structure of porous 316L stainless steel supported TiO2 membranes

Porous stainless steel (PSS) supported TiO₂ membrane was synthesized from colloidal TiO₂ sol by the sol–gel technique. Morphology and phase structure of the obtained membranes were regulated through optimizing the synthesis parameters including organic binders, aging periods of the parent sol and concentrations of the casting solutions as well as the sintering temperatures. Polyvinyl alcohol (PVA) 1750 was found to be feasible to fabricate TiO₂ membrane with relatively flat surface and homogeneous morphology without crack. The aging period of the parent sol, which was revealed to be very important to the morphology of the particles deposited in the membranes on PSS, was decided to be 24 h. The concentration, under which the membranes could avoid macro-pores and have a uniform thickness of approximately 8 μm, was regulated to 0.0036 mol/l. Besides, a homogeneous microstructure with grain sizes of 0.08–0.2 μm was obtained in the membrane with a pure rutile phase when sintered at 850 °C. The obtained PSS supported TiO₂ membrane with homogeneous microstructure and rutile phase may be very promising for practical applications.     

The catalytic role of oxide in the thermooxidative degradation of poly(methyl methacrylate)-TiO2 nanocomposites

The influence of TiO₂ nanoparticles on the thermal degradation of poly(methyl methacrylate) (PMMA) was investigated by TGA. The studied materials were characterized by Py-GC-MS, TEM, SEM, TGA, DSC and TGA-MS. The PMMA-TiO₂ nanocomposites were prepared by melt blending with different (5, 10, 15 and 20 wt% TiO₂) loadings. According to TGA results and to the activation energy (determined by the model-free isoconversional method of Vyazovkin), the incorporation of 5 wt% of TiO₂ nanoparticles into PMMA stabilizes it by more than 40 °C. However, for higher loading contents, a catalytic effect on the thermal decomposition was observed which increased with the oxide content. The results obtained by Py-GC-MS showed clearly that TiO₂ increases the formation of methanol, methacrylic acid and propanoic acid methyl ester during the degradation of PMMA. This catalytic effect could be explained through the interaction of the methoxy group of the methacrylate function with the hydroxyl groups present at the surface of the oxide particles.     

A novel microwave dielectric ceramic Ca2Zn4Ti16O38: Preparation and dielectric properties

A novel microwave dielectric powder with composition of Ca₂Zn₄Ti₁₆O₃₈ was synthesized through a citrate sol-gel process. The development of crystalline phases with heat-treating temperature for the gel derived powders was evaluated by using thermo-gravimetric analysis and X-ray powder diffraction analysis techniques. The pure phase of Ca₂Zn₄Ti₁₆O₃₈ with crichtonite crystal structure was obtained at relatively low temperature of 1000 °C. The synthesized powder has high reactivity and the dense ceramics with single crystalline phase were obtained at low sintering temperature of 1100 °C. Impedance spectroscopy and microwave dielectric measurements on sintered samples showed the present compound to be a modest dielectric insulator with excellent dielectric properties of ε_r∼47-49, Qf value ∼27,800-31,600 GHz and τ_f∼+45 to +50 ppm/°C. It shows comparable microwave dielectric properties to other moderate-permittivity microwave dielectrics, but much lower sintering temperature of 1100 °C.     

On the precipitation of coherent spinel nanoparticles in Ti-doped MgO

The Mg₂TiO₄/MgO composites prepared by reactive sintering of MgO and TiO₂ powders (9:1 molar ratio) at 1600 °C and then air-cooled or further aged at 900 °C were studied by X-ray diffraction and analytical electron microscopy in order to characterize the microstructures and formation mechanism of nanosized Mg₂TiO₄ spinel precipitated from Ti-doped MgO. Expulsion of Ti⁴⁺ during cooling caused the formation of (001)-specific Guinier-Preston zone under the influence of thermal/sintering stress and then the spinel precipitates, which were about 30 nm in size and nearly spherical with {111} and {100} facets to minimize coherency strain energy and surface energy. Secondary nanosized spinel was precipitated and became site saturated during aging at 900 °C, leaving a precipitate-free zone at the grain boundaries of Ti-doped MgO. The intergranular spinel became progressively Ti-richer upon aging at 900 °C and showed 〈110〉-specific diffuse scatter intensity likely due to short-range ordering and/or onset decomposition.     

Cr2O3-modified ZnO thick film resistors as LPG sensors

Thick films of pure ZnO were obtained by screen-printing technique. Surface functionalized ZnO thick films by Cr₂O₃ were obtained by dipping pure ZnO thick films into 0.01 M aqueous solution of chromium trioxide (CrO₃). The dipped films were fired at 500 °C for 30 min. Upon firing, the CrO₃ would reduce to Cr₂O₃. Cr₂O₃-activated (0.47 mass%) ZnO thick films resulted in LPG sensor. Upon exposure to 100 ppm LPG, the barrier height between Cr₂O₃ and ZnO grains decreases markedly, leading to a drastic decrease in resistance. The sensor was found to sense LPG at 350 °C and no cross sensitivity was observed to other hazardous, polluting and inflammable gases. The quick response (∼18 s) and fast recovery (∼42 s) are the main features of this sensor. The effects of microstructures and dopant concentrations on the gas sensing performance of the sensor were studied and discussed.     

Structural characterization and photocatalytic activity of hollow binary ZrO2/TiO2 oxide fibers

The formation of hollow binary ZrO₂/TiO₂ oxide fibers using mixed precursor solutions was achieved by activated carbon fibers templating technique combined with solvothermal process. The samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), N₂ adsorption, X-ray photoelectron spectroscopy (XPS), UV-vis, and infrared (IR) spectroscopy. The binary oxide system shows the anatase-type TiO₂ and tetragonal phase of ZrO₂, and the introduction of ZrO₂ notably inhibits the growth of TiO₂ nanocrystallites. Although calcined at 575 °C, all hollow ZrO₂/TiO₂ fibers exhibit higher surface areas (>113 m²/g) than pure TiO₂ hollow fibers. The Pyridine adsorption on ZrO₂/TiO₂ sample indicates the presence of stronger surface acid sites. Such properties bring about that the binary oxide system possesses higher efficiency and durable activity stability for photodegradation of gaseous ethylene and trichloromethane than P25 TiO₂. In addition, the macroscopic felt form for the resulting materials is more beneficial for practical applications than traditional catalysts forms.