Effects of a chemically modified multiwall carbon nanotubes on electro-optical properties of PDLC films

Polymer dispersed liquid crystal (PDLC) films are fabricated by well-known polymerization-induced phase separation method. In this paper, the dispersion of multi-walled carbon nanotubes (MWCNT) in liquid crystals has been enhanced by chemical modification and we have investigated their effects on the morphology, electro-optical properties and conductivity of the PDLC films. Results indicated that the threshold voltage and the saturation voltage of PDLC films decreased with the increase of the doping concentration of MWCNT or chemically modified MWCNT, because carbon nanotubes can enhance the electric field by reducing the resistivity of the medium and increasing the capacitance of the cells. It can be viewed obviously that the contrast ratio of the PDLC films doped with the chemically modified MWCNT is higher than that of the MWCNT.     

Novel method for dispersion of multiwall carbon nanotubes in poly(ethylene oxide) matrix using dicarboxylic acid salts

A simple and novel aqueous method was elaborated to disperse multiwall carbon nanotubes (MWCNT) in a poly(ethylene oxide) (PEO) matrix using the sodium salts of suberic acid (half and fully neutralized versions, HNSA and FNSA, respectively) as the modifiers. The incorporation of HNSA significantly improved the dispersion of MWCNT in PEO as reflected in a significant increase in melt viscosity and storage modulus in rheological measurements and dynamic mechanical thermal analysis, respectively. FNSA was proved to be the less efficient in this respect. This was explained in terms of cation‐Π (between FNSA, HNSA, and electron cloud of the CNT) and H‐bonding interactions (between HNSA and PEO) in accordance with Fourier transform infrared spectroscopic results. The dielectric and crystallization behaviors of the PEO/MWCNT/salt systems were studied and discussed, as well. The advantage of this method, applicable for water soluble polymers, is that it does not fully destroy the Π electron cloud of CNT opposed to chemical functionalization techniques. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1156–1165, 2009     

Crystallization-induced aggregation of block copolymer micelles: influence of crystallization kinetics on morphology

We present a systematic investigation of the crystallization and aggregation behavior of a poly(1,2-butadiene)-block-poly(ethylene oxide) diblock copolymer (PB-b-PEO) in n-heptane. n-Heptane is a poor solvent for PEO and at 70°C the block copolymer self-assembles into spherical micelles composed of a liquid PEO core and a soluble PB corona. Time- and temperature-dependent light scattering experiments revealed that when crystallization of the PEO cores is induced by cooling, the crystal morphology depends on the crystallization temperature (T _c ): Below 30°C, the high nucleation rate of the PEO core dictates the growth of the crystals by a fast aggregation of the micelles into meander-like (branched) structures due to a depletion of the micelles at the growth front. Above 30°C the nucleation rate is diminished and a relatively small crystal growth rate leads to the formation of twisted lamellae as imaged by scanning force microscopy. All data demonstrate that the formation mechanism of the crystals through micellar aggregation is dictated by two competitive effects, namely, by the nucleation and growth of the PEO core.     

Bioelectrochemical dehalogenations via direct electrochemistry of poly(ethylene oxide)-modified myoglobin

Catalytic reductive dehalogenation of hexachloroethane (HCE) was shown to be possible using a graphite electrode coated with a film of the poly(ester sulfonic acid) containing myoglobin (Mb). The effectiveness of the dehalogenation was limited by the solubility of HCE in aqueous solutions. In order to produce an electrode that could dehalogenate HCE in non-aqueous solutions, Mb was chemically modified by addition of poly(ethylene oxide) (PEO). The PEO–Mb–AQ29D modified electrode was found to be suitable for the reductive dehalogenation of HCE in ethanolic solutions. The catalytic response was shown to be linearly dependent on the bulk concentration of HCE.     

Enhanced NADH Oxidation Using Polytyramine/Carbon Nanotube Modified Electrodes for Ethanol Biosensing

Polytyramine (PT) has been electro‐deposited onto multi‐walled carbon nanotube (MWCNT) modified glassy carbon (GC) electrodes via oxidation of tyramine in 0.1 M H₃PO₄ by cycling the potential over the range of −400 mV to 1300 mV (versus Ag/AgCl). The reactivity of the resulting chemically‐modified electrodes was characterized using cyclic voltammetry in the presence and absence of reduced nicotinamide adenine dinucleotide (NADH). The modified electrodes displayed electrochemical activity due to the formation of quinone species and were catalytically active towards NADH oxidation by lowering the oxidation peak potential by 170 mV compared to the value of the MWCNT modified electrode with a peak potential of 180±10 mV (versus Ag/AgCl). The MWCNT/PT surface was further characterized using SEM and XPS methods, which indicated that a thin polymeric film had been formed on the electrode surface. The present work demonstrates the advantage of using PT as a platform that combines both the immobilization of alcohol dehydrogenase (ADH) and the mediation of NADH oxidation at a low overpotential essential to the design of high performance ethanol biosensors, all within an easily electropolymerizable film. The resulting biosensor displayed an ethanol sensitivity of 4.28±0.06 μA mM⁻¹ cm⁻², a linear range between 0.1 mM and 0.5 mM and a detection limit of 10 μM.     

Influence of modification of MWCNTs on the structure and performance of MWCNT‐Poly(MMA‐AM) hybrid membranes

Hybrid membranes containing multi‐walled carbon nanotubes (MWCNTs) were initially prepared to separate benzene/cyclohexane mixtures. Subsequently, MWCNT surfaces were chemically modified using two methods to change the surface polarity of the MWCNTs and improve the distribution thereof in Poly(methylmethacrylate) (PMMA). This change consequently enhanced the separation performance of hybrid membranes with MWCNTs. Raman spectroscopy was used to characterize the structure of the pristine MWCNTs and the modified MWCNTs. The morphology and distribution of the MWCNTs in PMMA were investigated by transmission electron microscopy. The results showed that the addition of MWCNTs clearly improved the separation performance of the hybrid membranes. Surface modification introduced polar groups onto the MWCNT surface, which significantly improved the distribution of MWCNTs in the PMMA membranes and the performance of hybrid membranes. MWCNTs with higher surface polarity also increased the amount of MWCNTs distributed homogeneously in PMMA. Aminated MWCNTs (MWCNT‐NH₂) showed the highest surface polarity. Thus, the content of MWCNT‐NH₂ well distributed in PMMA was the highest among the three types of MWCNTs. The highest separation factor for the hybrid membranes with 1.0 wt% MWCNT‐NH₂ was about seven times that of membranes containing pristine MWCNTs. Copyright © 2013 John Wiley & Sons, Ltd.     

Micellar structure and mechanical properties of block copolymer‐modified epoxies

Amphiphilic block copolymers provide a unique means for toughening epoxy resins because they can self‐assemble into different inclusion shapes before epoxy curing. The two examples reported here are spherical micelles and vesicles, which form in blends containing epoxy and symmetric or asymmetric poly(ethylene oxide)–poly(ethylene‐alt‐propylene) (PEO–PEP) block copolymer with PEO volume fractions of 0.5 and 0.26, respectively. The vesicles and spherical micelles were characterized by transmission electron microscopy and small‐angle X‐ray scattering (SAXS), respectively. SAXS data from the spherical micelles were fit to the Percus–Yevick model for a liquid‐like packing of spheres with hard‐core interactions. Mechanical properties of spherical‐micelle‐modified and vesicle‐modified epoxies in the dilute limit are compared. The glass‐transition temperature and Young's (storage) modulus were tested with dynamic mechanical spectroscopy, and compact‐tension experiments were performed to determine the critical plane‐strain energy release rate for fracture. Vesicles were most effective in improving the epoxy fracture resistance. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2996–3010, 2001     

Molecular motion,morphology, and thermal properties of multiwall carbon nanotube/polysilsesquioxane composite

Diglycidyl ether of bisphenol A (DGEBA)‐bridged polyorganosiloxane precursors have been prepared successfully by reacting diglycidyl ether of bisphenol A epoxy resin with 3‐aminopropyltriethoxysilane. Acid‐modified and unmodified multiwalled carbon nanotube (MWCNT) were dispersed in the diglycidyl ether of bisphenol A‐bridged polyorganosiloxane precursors and cured to prepare the carbon nanotube/diglycidyl ether of bisphenol A‐bridged polysilsesquioxane (MWCNT/DGEBA‐PSSQ) composites. The molecular motion of MWCNT/DGEBA‐PSSQ nanocomposites was studied by high‐resolution solid‐state ¹³C NMR. Acid‐modification can improve the affinity between MWCNT and the polymer matrix. The molecular motion of the DGEBA‐PSSQ decreased with acid‐modified MWCNT content. However, when unmodified MWCNT was used, the molecular motion of the DGEBA‐PSSQ was increased. SEM and TEM microphotographs confirm that acid‐modified MWCNT exhibits better dispersion than unmodified MWCNT in DGBEA‐PSSQ. The dynamic mechanical properties of acid‐modified MWCNT/DGBEA‐PSSQ composites are more favorable than those of unmodified MWCNT. T_g of the DGEBA‐PSSQ decreased from 174.0 °C (neat DGEBA‐PSSQ) to 159.0 °C (1 wt % unmodified MWCNT) and 156.0 °C (1 wt % acid‐modified MWCNT). The storage modulus (at 30 °C) of the DGEBA‐PSSQ increased from 1.23 × 10⁹ Pa (neat DGEBA‐PSSQ) to 1.65 × 10⁹ Pa (1 wt % acid‐modified MWCNT). However, when unmodified MWCNT was used, the storage modulus of the DGEBA‐PSSQ decreased to 6.88 × 10⁸ Pa (1 wt % unmodified MWCNT). At high temperature, above 150 °C, storage modulus of nanocomposites was higher than that of neat polymer system. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 472–482, 2008     

Conformation and electrochemical reduction of myoglobin in PEO oligomers

Horse-heart myoglobin (Mb) was modified with poly(ethylene oxide) (PEO) to solubilize it in PEO oligomers. PEO-modified Mb (PEO–Mb) showed a quasi-reversible electrochemical redox reaction in PEO₂₀₀ (molar mass of 200 g). PEO–Mbs, modified with lower molecular weight of PEO chains, were soluble in PEO oligomers with wider range of molecular weight. A conformation of PEO–Mb was studied with circular dichroism spectroscopy in phosphate buffer solution (PBS) or PEO oligomers. The α-helix content of PEO–Mb, determined by the molar ellipticity at 222 nm, decreased from 71% to about 58% after PEO modification. However, the degree of PEO modification did not affect the α-helix content of PEO–Mbs. On the other hand, the α-helix content of PEO–Mbs was reduced by lowering the molecular weight of the modified PEO chains. Since the α-helix content of PEO–Mb in PBS and that in the PEO oligomers were almost identical, the conformation of PEO–Mb in PBS was considered to be maintained even in PEO oligomers. Although the reduction rate constant of PEO–Mb in PEO oligomers depended on the total molecular weight of the PEO–Mbs, their relation did not obey the Stokes–Einstein equation. The reduction of the PEO–Mb was probably affected by the interfacial electron transfer process at the electrode surface rather than by diffusion in the PEO oligomer.     

Preparation and morphological,electrical, and mechanical properties of polyimide‐grafted MWCNT/polyimide composite

Precursor of polyimide, polyamic acid has been prepared sucessfully. Acid‐modified carbon nanotube (MWCNT) was grafted with soluble polyimide then was added to the polyamic acid and heated to 300 °C to form polyimide/carbon nanotube composite via imidation. Morphology, mechanical properties and electrical resistivity of the MWCNT/polyimide composites have been studied. Transmission electron microscope microphotographs show that the diameter of soluble polyimide‐grafted MWCNT was increased from 30–60 nm to 200 nm, that is a thickness of 70–85 nm of the soluble polyimide was grafted on the MWCNT surface. PI‐g‐MWCNT was well dispersed in the polymer matrix. Percolation threshold of MWCNT/polyimide composites has been investigated. PI‐g‐MWCNT/PI composites exhibit lower electrical resistivity than that of the acid‐modified MWCNT/PI composites. The surface resistivity of 5.0 phr MWCNT/polyimide composites was 2.82 × 10⁸ Ω/cm² (PI‐g‐MWCNT) and 2.53 × 10⁹ Ω/cm² (acid‐modified MWCNT). The volume resistivity of 5.0 phr MWCNT/polyimide composites was 8.77 × 10⁶ Ω cm (PI‐g‐MWCNT) and 1.33 × 10¹³ Ω cm (acid‐modified MWCNT).Tensile strength and Young's modulus increased significantly with the increase of MWCNT content. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3349–3358, 2007     

Model experiments for a molecular understanding of polymer crystallization

Time‐resolved real‐space observations of morphology and pattern formation resulting from crystallization of ultrathin films of low‐molecular‐weight poly(ethylene oxide) (PEO) or diblock copolymers containing PEO shed light on the mechanisms of how polymer crystals are formed. We used simple but restricted geometries like thin films of controlled thickness or confinement resulting from block copolymer mesotructures. Under such conditions, we were able to relate the observed morphology and its temporal evolution directly to molecular processes and the kinetics of crystal growth. We demonstrate that changes in the morphology with time are due to different thermal histories and are the consequence of the mestable nature of polymer crystals. Information about the nucleation process was obtained by examining crystal formation in 12‐nm small spherical cells of a block copolymer mesostructure. We discuss the advantages of thin‐film studies for a better understanding of polymer crystallization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1869–1877, 2003     

Optical absorption spectra from rare-earth ions in polymers: the effect of the polymer host

A Molecular Dynamics (MD) based modified Judd/Ofelt approach has been used to simulate UV-VIS absorption spectra for different concentrations of Er(CF₃SO₃)₃ (erbium triflate) in the amorphous polymer host poly(ethylene oxide), PEO. The simulations have been performed for systems containing both single-chain PEO and PEO with an attached side-chain. Effects on the optical properties of the introduction of side-chains are demonstrated. Qualitative inspection of the calculated spectra would suggest that similarities in the crystal field experienced by individual Er ions in qualitatively different local environments will make structural information difficult to access from this procedure.     

利用x射线衍射法测定不同序列的聚苯乙烯-聚环氧乙烷嵌段共聚物的结晶度和晶粒大小

PSt-PEO嵌段共聚物,由于其PSt链段的亲油性及无定形性,PEO链段亲水性及结晶性所具有的两重性质^[1],使得它们在理论研究及实际应用上都具有较大的意义。但对其结晶度及晶粒大小的测定还不曾见报导。     

Hg(II) immobilized MWCNT graphite electrode for the anodic stripping voltammetric determination of lead and cadmium

The preparation of Hg(II)-modified multi walled carbon nanotube (MWCNT) by reaction of oxidized MWCNT with aqueous HgCl₂ was carried out. The Hg(II)-modified multi walled carbon nanotube (Hg(II)/MWCNT) dispersed in Nafion solution was used to coat the polished graphite electrode surface. The Hg(II)/MWCNT modified graphite electrode was held at a cathodic potential (−1.0 V) to reduce the coordinated Hg(II) to Hg forming nanodroplets of Hg. The modified electrode was characterized by FESEM/EDAX which provided useful insights on the morphology of the electrode. The SEM images showed droplets of Hg in the size of around 260 nm uniformly distributed on the MWCNT. Differential pulse anodic stripping voltammetry (DPASV) and electrochemical impedance spectroscopy were used to study the Hg(II) binding with MWCNT. Differential pulse anodic stripping voltammetry of ppb levels of cadmium and lead using the modified electrode yielded well-defined peaks with low background current under a short deposition time. Detection limit of 0.94 and 1.8 ng L⁻¹ were obtained following a 3 min deposition for Pb(II) and Cd(II), respectively. Various experimental parameters were characterized and optimized. High reproducibility was observed from the RSD values for 20 repetitive measurements of Pb(II) and Cd(II) (1.7 and 1.9%, respectively). The determination of Pb(II) and Cd(II) in tap water and Pb(II) in human hair samples was carried out. The above method of fabrication of Hg(II)/MWCNT modified graphite electrode clearly suggests a safe route for preparing Hg immobilized electrode for stripping analysis.     

碳纳米管载Pd-Au催化剂的合成及其对甲酸氧化的电催化性能

将萘-1-亚甲基膦酸通过π-π堆积作用修饰在多壁碳纳米管(MWCNT)上,然后制备了MWCNT载Pd(Pd/MWCNT)催化剂。 利用Pd和HAuCl4间的置换反应制得MWCNT载Pd-Au(Pd-Au/MWCNT)催化剂。 透射电子显微镜(TEM)、X射线光电子能谱(XPS)和X射线衍射光谱(XRD)测试结果显示,非合金化的Pd-Au纳米粒子均匀分布在MWCNT表面。 循环伏安和计时电流测试显示,非合金化Pd-Au/MWCNT催化剂对甲酸氧化的电催化活性以及稳定性优于Pd/MWCNT催化剂。     

Electrochemical Sensor Prepared from Molecularly Imprinted Polymer for Recognition of 1,3-Dinitrobenzene (DNB)

An electrochemical sensor was modified with multi‐wall carbon nanotubes (MWCNT) and molecularly imprinted polymer (MIP) material synthesized with acrylamide and ethylene glycol dimethacrylate (EGDMA) in the presence of 1,3‐dinitrobenzene (DNB) as the template molecule. The MWCNT and MIP layers were successively modified on the surface of a glassy carbon electrode (GCE), of which the MIP film works as an artificial receptor due to its specific molecular recognition sites. The MIP material was characterized by FT‐IR and electrochemical methods of square wave voltammetry (SWV). The interferences of other nitroaromatic compounds (NAC) such as 2,4,6‐trinitrotoluene (TNT), 1,3,5‐trinitrobenzene (TNB) and 2,4‐dinitrotoluene (DNT) to DNB were also investigated by the prepared MIP/MWCNT electrode. Compared with other traditional sensors, the MIP/MWCNT modified electrode shows good selectivity and sensitivity. In addition, the current responses to DNB are linear with the concentration ranging from 4.5×10^?8 to 8.5×10^?6 mol/L with the detection limits of 2.5×10^?8 (?0.58 V) and 1.5×10^?8 mol/L (?0.69 V) (S/N=3). The construction process of MIP/MWCNT modified electrode was also studied as well. All results indicate that the MIP/MWCNT modified electrode established an improving way for simple, fast and selective analysis of DNB.     

Poly(vinyltriethoxysilane) modified MWCNT/polyimide nanocomposites—Preparation,morphological, mechanical,and electrical properties

Multi‐walled carbon nanotube (MWCNT) modified by vinyltriethoxysilane (VTES) via free radical reaction has been prepared (poly (vinyltriethoxysilane) modified MWCNTs, PVTES‐MWCNT). Precursor of polyimide, polyamic acid has been synthesized by reacting 4,4′‐oxydianiline with 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride. PVTES‐MWCNT were then mixed with polyamic acid and heated to 300 °C to form CNT/polyimide composite. During the imidization processes, the silanes on CNT surface reacted with each other and may be connected together by covalent bond (Si? O? Si). The PVTES‐MWCNT was analyzed by Fourier transform infrared and X‐ray photoelectron spectroscopy. The PVTES‐MWCNT/polyimide composites were analyzed by CP/MAS solid state ²⁹Si nuclear magnetic resonance (NMR) spectroscopy. Morphological properties of the PVTES‐MWCNT/polyimide composites were investigated by scanning electron microscope and transmission electron microscope. Electrical conductivity increased dramatically comparing to the unmodified MWCNT/polyimide composites. Mechanical properties of nanocomposite were enhanced significantly by PVTES‐MWCNT. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 803–816, 2008     

Glucose Biosensor Based on Multi‐Walled Carbon Nanotube Modified Glassy Carbon Electrode

An amperometric glucose biosensor based on multi‐walled carbon nanotube (MWCNT) modified glassy carbon electrode has been developed. MWCNT‐modified glassy carbon electrode was obtained by casting the electrode surface with multi‐walled carbon nanotube materials. Glucose oxidase was co‐immobilized on the MWCNT‐modified glassy carbon surface by electrochemical deposition of poly(o‐phenylenediamine) film. Enhanced catalytic electroreduction behavior of oxygen at MWCNT‐modified electrode surface was observed at a potential of ?0.40 V (vs. Ag|AgCl) in neutral medium. The steady‐state amperometric response to glucose was determined at a selected potential of ?0.30 V by means of the reduction of dissolved oxygen consumed by the enzymatic reaction. Common interferents such as ascorbic acid, 4‐acetamidophenol, and uric acid did not interfere in the glucose determination. The linear range for glucose determination extended to 2.0 mM and the detection limit was estimated to be about 0.03 mM.     

Correlation between crystallization kinetics and microdomain morphology in block copolymer blends exhibiting confined crystallization

The crystallization kinetics of poly(ethylene oxide) (PEO) blocks in poly(ethylene oxide)‐block‐poly(1,4‐butadiene) (PEO‐b‐PB)/poly(1,4‐butadiene) (PB) blends were previously found to display a one‐to‐one correlation with the microdomain morphology. The distinct correlation was postulated to stem from the homogeneous nucleation‐controlled crystallization in the cylindrical and spherical PEO microdomains, where there existed a direct proportionality between the nucleation rate and the individual domain volume. This criterion was valid for confined crystallization in which the crystallization was spatially restricted within the individual domains. However, it was possibly not applicable to PEO‐b‐PB/PB, in that the melt mesophase was strongly perturbed upon crystallization. Therefore, it may be speculated that the crystal growth front developed in a given microdomain could intrude into the nearby noncrystalline domains, yielding the condition of cooperative crystallization. To establish an unambiguous model system for verifying the existence of microdomain‐tailored kinetics in confined crystallization, we crosslinked amorphous PB blocks in PEO‐b‐PB/PB with a photoinitiated crosslinking reaction to effectively suppress the cooperative crystallization. Small‐angle X‐ray scattering revealed that, in contrast to the noncrosslinked systems, the pre‐existing domain morphology in the melt was retained upon crystallization. The crystallization kinetics in the crosslinked system also exhibited a parallel transition with the morphological transformation, thereby verifying the existence of microdomain‐tailored kinetics in the confined crystallization of block copolymers. Homogeneous nucleation‐controlled crystallizations in cylindrical and spherical morphologies were demonstrated in an isothermal crystallization study in which the corresponding crystallinity developments followed a simple exponential rule not prescribed by conventional spherulitic crystallization. Despite the effective confinement imposed by the crosslinked PB phase, crystallization in the lamellar phase still proceeded through a mechanism analogous to the spherulitic crystallization of homopolymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 519–529, 2002; DOI 10.1002/polb.10121     

普鲁士蓝/多壁碳纳米管修饰电极测定维生素C

利用电化学方法在多壁碳纳米管修饰的玻碳电极表面聚合一层普鲁士蓝,制备普鲁士蓝/多壁碳纳米管修饰玻碳电极,运用循环伏安法研究了维生素C(vc)在该修饰电极上的电化学行为.该修饰电极对Vc显示出快速的电化学响应和较好的电催化活性,在pH为4.0的磷酸盐溶液中,Ve浓度与其氧化峰电流在8.0×10-4～1.0×10-2 mol/L范围内呈现良好的线性关系,相关系数为0.9993,检测限为6.4×10-5mol/L.该电极具有较好的稳定性和重现性.