Simultaneous Determination of Organic Acids in Wine Samples by Capillary Electrophoresis and UV Detection: Optimization with Five Different Background Electrolytes

A simple technique is described for the routine capillary electrophoretic determination of organic acids in wine samples. Several aromatic and non‐aromatic compounds, including phthalic acid, benzoic acid, sorbic acid, boric acid, and phosphate, were evaluated as background electrolytes in order to obtain the highest resolution and detection sensivity. Factors that affect capillary electrophoretic separation such as the concentration and pH of the background electrolyte (BGE), the concentration of the electroosmotic flow modifier (EOF), and methanol addition to the electrolyte were investigated systematically. Tartaric, malic, succinic, acetic, and lactic acids were determined simultaneously in approximately six minutes using an electrolyte containing 3 mM phosphate and 0.5 mM myristyltrimethylammonium bromide (MTAB) as electroosmotic flow modifier at pH 6.5. This method is quantitative, with recoveries in the 90–102% range and linear up to 50 mg L^–1. The precision is better than 1% and the procedure shows the appropriate sensibility, with detection limits between 0.015 and 0.054 mg L^–1. The proposed method was successfully employed for the determination of organic acids in wine samples by direct sample injection after appropriate dilution and filtration.     

Analysis of Calix[4]arenes Using Nonaqueous Capillary Electrophoresis

In nonaqueous capillary electrophoresis (NACE), an organic solvent is used in place of an aqueous medium as the background solution to improve the solubility and selectivity for hydrophobic analytes. In this study, we employed NACE with UV detection for the analysis of eight calix[4]arenes. We examined the influence of several parameters—the buffer composition, the nonaqueous solvent‘s composition and proportion, and the concentration of the electrolyte of the nonaqueous buffer—on the efficiency of the electrophoretic separation. The separation was achieved through the analyte's different effective mobility via different degrees of deprotonation on the phenolic OH groups of the calix[4]arene. This deprotonation can further affect the analyte's ability to form a complex with the metal ion. The optimized background electrolyte (BGE), comprising a mixture of N‐methylformamide/acetonitrile (30:70, v/v) and 100 mM AcOH/20 mM NH₄OAc, provided rapid (<11 min) separation of the calix[4]arenes with good resolution. The relative standard deviations of the migration times for the eight analytes were all less than 1%. Within the calibration concentration range, the coefficients of determination (R²) were all greater than 0.9914. Thus, the present study demonstrated NACE can provide adequate separation for the analysis of calix[4]arenes.     

Polymeric ionic liquid as a dynamic coating additive for separation of basic proteins by capillary electrophoresis

A simple and economical capillary electrophoresis method has been developed for the analysis of four model basic proteins by employing a polymeric ionic liquid (PIL), poly(1-vinyl-3-butylimidazolium) bromide, as the dynamic coating additive. When a small amount of PIL was present in the background electrolyte, a cationic coating on the inner surface of fused-silica capillary was established. These PIL modified capillaries not only generated a stable reversed electroosmotic flow, but also effectively eliminated the wall adsorption of proteins. Several important parameters such as the PIL concentration in the background electrolyte, pH values and concentrations of the background electrolyte were optimized to improve the separation of basic proteins. Consequently, under the optimum conditions, a satisfied separation of basic proteins with peak efficiencies ranging from 247,000 to 540,000 (plates m⁻¹) had been accomplished within 11 min. The run-to-run RSDs (n = 3) of the migration times for the four basic proteins were all less than 0.37%.     

Extraction Properties of Modified Silica Gel for Metal Analysis by Energy Dispersive X-Ray Fluorescence

Abstract

The separation of water‐soluble vitamins by capillary zone electrophoresis was developed, in which on‐line concentration methods, namely field‐enhanced sample stacking and dynamic pH junction, were utilized to improve the detection sensitivity. The effects of some critical parameters, including pH and concentration of background electrolyte, sample matrix pH and concentration, and injection volume were examined. The effects of field‐enhanced sample stacking and dynamic pH junction on the separation resolution and concentration efficiency were compared. The limits of detection of the vitamins were from 6 to 119 ng ml^?1 (2.7×10^?8 to 53.4×10^?8 M) based on the signal‐to‐noise ratio of 3 and the relative standard deviations of migration time and peak area for each vitamin (1 µg ml^?1) were less than 3.5% using the field‐enhanced sample stacking as an on‐line concentration method. The developed method was applied to the analysis of water‐soluble vitamins in corns.     

Rapid determination of mono and dinitrophenols by DPP, in the presence of lead and cadmium and using concentrated CaCl2 electrolyte

The contamination of drinking water and industrial wastewaters is a critical environmental problem. The nitrophenol, dinitrophenol, cadmium, and lead contaminants are classified as hazardous compounds. Their rapid determination may be obtained using differential pulse polarography with concentrated electrolyte. CaCl₂, which is very soluble to levels exceeding 5 mol l^–1, allows separation of coalescent peaks at 0.1 mol l^–1. A systematic study undertaken from 0.1 to 5 mol l^–1 shows good separation of lead and cadmium from the organic compounds, and optimization of the electrolyte concentration according to the objective is described. Preconcentration of real samples is necessary because pollution levels are usually very low.     

Determination of organic acids by capillary electrophoresis with simultaneous addition of Ca and Mg as complexing agents

Summary A capillary electrophoretic method, with divalent cations as complexing agents in the electrolyte, has been developed for separation and determination of the low molecular weight organic acids most commonly found in wine, viz. formic, fumaric, succinic, oxalic, malic, tartaric, acetic, lactic, and citric acids. The separation conditions optimized were electrolyte concentration, organic flow modifier concentration, type and concentration of complexing agents in the electrolyte, and injection time. The best resolution of some of the acids studied was achieved by use of an electrolyte containing tetraborate buffer (10mm) at pH 9.3, an organic flow modifier (tetradecyltrimethylammonium hydroxide), and Ca²⁺ (10 ppm) and Mg²⁺ (10 ppm) as complexing agents. Other conditions used in the method were hydrostatic injection (10 cm height for 30 s), detection at 185 nm, and temperature 20°C. For all the acids studied detector response was linear for the concentration ranges considered. The repeatability of each point on the calibration plot for standards (n=4) was generally better than 1% the method was applied to samples of must, wine, brandy, and vinegar from the Jerez region.     

Separation of Fluoroquinolones by MEKC Modified with Hydrophobic Ionic Liquid as a Modifier

The hydrophobic ionic liquid [BMIM]PF₆ (1-butyl-3-methylimidazolium hexafluorophosphate) can interact with sodium dodecyl sulfate (SDS) micelles in aqueous solution and modify their physicochemical properties to produce a unique separation efficiency in micellar electrokinetic chromatography (MEKC). An MEKC method was developed using [BMIM]PF₆ as a modifier for separating eight fluoroquinolone compounds (ciprofloxacin, enrofloxacin, gatifloxacin, ofloxacin, norfloxacin, enoxacin, pazufloxacin, and tosufloxacin). The effects of several parameters on the separation selectivity, e.g., pH, concentration of background electrolyte, concentration ratio and amount of [BMIM]PF₆ and SDS, were investigated. Under the optimal conditions of 10 mmol L⁻¹ sodium borate, pH 7.1, 1.7% (w/w) SDS, 1.5% (w/w) [BMIM]PF₆ with 18 kV as running voltage, the eight investigated quinolone compounds were baseline separated within 15 min. The selectivity of the developed method differed from that of the simple SDS micelles system containing no ionic liquid. The results suggest that hydrophobic ionic liquids should be promising modifiers in capillary electrophoresis, especially in MEKC analysis.

     

Investigation of Enantiomeric Separation of Chiral Drugs by CE Using Cu(II)–Clindamycin Complex as a Novel Chiral Selector

The enantiomeric separation of several basic drugs was investigated using copper(II)–clindamycin as a new chiral selector. The results show that the chiral selector allows high-resolution separation of some racemic basic drugs, including tropicamide, propranolol, sotalol, bisoprolol, epinephrine, esmolol, atenolol, and metoprolol. The enantioselectivity was influenced by parameters such as the type of metal ion, ratio of clindamycin and Cu(II), pH of the background electrolyte, clindamycin concentration, applied voltage, and capillary temperature. The optimal separation conditions were determined to be 20 mM clindamycin/10 mM Cu²⁺, pH 9.06, at 20 kV and 22 °C within 25 min.

     

Investigation of Enantiomeric Separation of Chiral Drugs by CE Using Cu(II)�CClindamycin Complex as a Novel Chiral Selector

The enantiomeric separation of several basic drugs was investigated using copper(II)?Cclindamycin as a new chiral selector. The results show that the chiral selector allows high-resolution separation of some racemic basic drugs, including tropicamide, propranolol, sotalol, bisoprolol, epinephrine, esmolol, atenolol, and metoprolol. The enantioselectivity was influenced by parameters such as the type of metal ion, ratio of clindamycin and Cu(II), pH of the background electrolyte, clindamycin concentration, applied voltage, and capillary temperature. The optimal separation conditions were determined to be 20 mM clindamycin/10 mM Cu²⁺, pH 9.06, at 20 kV and 22 °C within 25 min.     

Using dendrimers and hyperbranched polymers in chromatography and electrophoresis

The use of a new class of high-molecular-weight substances, dendritic polymers (dendrimers and hyperbranched polymers), as components of chromatographic and electrophoretic systems is discussed; the effect of their introduction into a background electrolyte or an eluent on the separation efficiency and selectivity of organic compounds of different classes is considered.     

Analysis of 3‐quinuclidinol derivatives by capillary electrophoresis

Capillary electrophoresis with indirect UV detection was applied to the analysis of a mixture of 3‐quinuclidinol and its four quaternary derivatives (N‐methyl, N‐ethyl, N‐propyl, and N‐isopropyl derivative). 10 mM imidazole acetate buffer, pH = 4.0 offers suitable detection sensitivity (LOD = 1 μmol L^–1) and permits separation of the mixture except for the pair 3‐quinuclidinol–N‐methyl derivative. The separation of all analytes was achieved on addition of 15 mmol L^–1 β‐cyclodextrin or 25% (w/w) polyethylene glycol 2000 to the background electrolyte. The optimized method was employed for the analysis of pond water spiked with these analytes. Actual ionic mobilities of the studied compounds were measured using mobility standards (potassium, sodium, tetramethyl‐ and tetrabutylammonium). The migration index was derived as another identification parameter based on migration data and the precision of the obtained values is discussed in brief.     

Separation of Organomercury Species Using Nonaqueous Capillary Electrophoresis Coupled with Sample Stacking and Electrokinetic Injection Techniques

A nonaqueous capillary electrophoresis (NACE) method, 30 mM ammonium acetate in methanol as background electrolyte (BGE), was developed for separation of the organomercury species without complexing reagents. The effects of different solutes and solvents in BGE were studied. Three species of organomercury, methylmercury, ethylmercury and phenylmercury, were separated well and all the number of theoretical plates were over 10⁶. The present NACE method was also coupled with sample stacking and electrokinetic injection techniques to enhance the detection sensitivity. Under the optimum conditions, the limit of detection (S/N = 3) is 18 ng mL⁻¹ and the linear relation range from 40 to 750 ng mL⁻¹ were obtained for methylmercury.     

Separation and determination of lignans from seeds of Schisandra species by micellar electrokinetic capillary chromatography using ionic liquid as modifier

In this paper, a micellar electrokinetic chromatographic (MEKC) method using ionic liquid as modifier for the quantification of the active components of lignans found in the medicinal herbs Schisandra species was developed for the first time. Preliminary investigations employing sodium dodecyl sulfate (SDS) as surfactant did not lead to the necessary resolution of the studied compounds, the addition of ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM-BF4) to the SDS micellar system resulted in the complete separation of all the compounds. The effects on the separation by several parameters such as BMIM-BF4 and SDS concentration, applied voltage, background electrolyte pH and concentration, were evaluated. Under the optimal conditions (5 mM borate-5 mM phosphate buffer in the presence of 20 mM SDS and 10 mM BMIM-BF4, pH 9.2, applied voltage 25 kV and detection at 254 nm), the method successfully applied to the determination of lignans in extracts of Schisandra chinensis (Turcz.) Baill. and Schisandra henryi C.B. Clarke in less than 13 min. The separation mechanism was also discussed.     

Optimisation of probe concentration in indirect photometric detection in capillary electrophoresis using highly absorbing dyes

In indirect photometric detection in capillary electrophoresis, the concentration of the absorbing probe ion in the background electrolyte should be as high as possible in order to increase the dynamic range of the detection method. For relatively low absorptivity probes (epsilon < 2000 L mol(-1)cm(-1)) used under typical conditions (75 microm ID capillary) the maximum probe concentration is normally limited by the separation current. However, for medium (epsilon approximately/= 2000-15000 L mol(-1)cm(-1)) and especially for high (epsilon > 15000 L mol(-1)cm(-1)) absorptivity probes such as dyes, the maximum concentration may be limited by the background absorbance of the electrolyte which must fall within the linearity range of the detector. In this work, it is shown that another practical factor limiting the probe concentration is the adsorption of probe onto the capillary wall at higher concentrations, resulting in unstable baseline and increased noise. Use of a zwitterionic surfactant to suppress adsorption enabled the concentration of a model probe anion (tartrazine) to be increased by a factor of six times (to 3 mM). This resulted in significant improvements in peaks shapes, resolution between peaks, detection sensitivity and linear calibration range for the analyte anions. Baseline separation of a test mixture was maintained up to 7.5 mM total concentration of sample coions injected (13.7 nL) for the 3 mM electrolyte, with detection limits ranging from 0.63 to 0.94 microM. Peak height reproducibility (over 20 consecutive injections) was improved (values ranging from 1.1 to 1.9%) compared with electrolytes containing lower concentrations of the probe. Overall, the optimised, higher concentration probe electrolyte provided the sensitivity benefits of highly absorbing probes with the additional benefits of ruggedness and improved stacking, peak shapes and resolution.     

A rapid carrier-free separation method for divalent rare earths

A separation of carrier-free divalent rare earths by electrolytic reduction and amalgamation is described. The separation is carried out in a water-jacketed cell, 1 cm diameter by 10 cm long, fitted with a stopcock at the bottom. The cell utilizes a Pt anode and Hg cathode. The electrolyte used is potassium citrate-rare earth acetate at a concentration of 10 mg rare earth oxide per ml. The decontamination factor observed for Lu in a typical separation for Yb is ≥10⁴. Sm, Eu, and Yb are all amalgamated if present in the sample. For the present study, the parameters have been evaluated primarily for the case of Yb. A current of 100 mA is applied to 0.5 ml of electrolyte containing 1–1000 μg of Yb(III) for 5 min. The amalgam is decomposed and the Yb recovered by shaking for 1 min with 6M HCl. The overall time required is about 10 min and the yield is reproducible at 84–85%. Under these conditions, the electrolyte may contain up to 3.5 mg of Yb although at 2 mg the yield begins to decrease. The effects of current time, density and electrolyte concentration are discussed. This method has the advantage of being rapid and carrier-free, and the separated rare earth is in a form suitable for further chemical separation if required. Based on work performed under the auspices of the U.S. Atomic Energy Commission.     

聚合离子液体用作毛细管电泳背景电解质添加剂快速高效分离5种核苷类化合物

将聚乙烯基-3-乙基咪唑溴盐离子液体用作毛细管电泳背景电解质添加剂,利用聚合离子液体的阳离子聚合物性质静电吸附到毛细管内表面,成功实现电渗流的有效反转,建立了共电渗流模式下5种核苷类化合物分离的新方法。考察了聚合离子液体浓度、pH值等因素对电渗流的影响。在优化实验条件下,3.1 min内实现了对5种核苷类化合物的快速高效分离;将该方法分别与不加添加剂和加入离子液体单体后的体系进行对比,结果表明,该方法大大缩短了5种核苷类化合物的分析时间,提高了分析效率,最高柱效达95万/m塔板数,分析物的迁移时间RSD均不高于0.38%。该方法简单、快速、重复性好,具有很好的应用前景。     

Multivariate optimisation of a cyclodextrin-assisted-capillary zone electrophoretic method for the separation of torasemide and its metabolites

In this work, a rapid cyclodextrin-assisted capillary electrophoretic method is developed for the separation of the diuretic torasemide and three of its metabolites. Both fractional factorial and central composite designs were employed to optimise the separation method. The factors studied were pH, concentration of methyl-β-cyclodextrin, concentration of the background electrolyte and percentage of acetonitrile as organic modifier. Monitored response was a composite quality response (Q*) which balanced conflicting normalized responses, such as resolution and migration time. Optimal separation of the four studied compounds was achieved in less than 6.5 min, using an electrolyte of 60 mM borate buffer with no organic modifier and 25 mM methyl-β-cyclodextrin concentration adjusted to pH 8.0 at a potential of 30 kV. Detection wavelength and temperature were 197 nm and 20 °C respectively. This work means a significant improvement with regard to a previous separation method for these compounds developed in our laboratory.     

Effect of NaOH on large-volume sample stacking of haloacetic acids in capillary zone electrophoresis with a low-pH buffer

Large-volume sample stacking (LVSS) is an effective on-capillary sample concentration method in capillary zone electrophoresis, which can be applied to the sample in a low-conductivity matrix. NaOH solution is commonly used to back-extract acidic compounds from organic solvent in sample pretreatment. The effect of NaOH as sample matrix on LVSS of haloacetic acids was investigated in this study. It was found that the presence of NaOH in sample did not compromise, but rather help the sample stacking performance if a low pH background electrolyte (BGE) was used. The sensitivity enhancement factor was higher than the case when sample was dissolved in pure water or diluted BGE. Compared with conventional injection (0.4% capillary volume), 97-120-fold sensitivity enhancement in terms of peak height was obtained without deterioration of separation with an injection amount equal to 20% of the capillary volume. This method was applied to determine haloacetic acids in tap water by combination with liquid-liquid extraction and back-extraction into NaOH solution. Limits of detection at sub-ppb levels were obtained for real samples with direct UV detection.     

Optimized Method for the Determination of Prednisolone, Zn-Bacitracin and Phenylephrine in Local Pharmaceutical Preparations by Micellar Electrokinetic Capillary Chromatography

Summary A new, rapid and simple method is described and applied to resolve and quantify mixtures of prednisolone, Zn-bacitracin and phenylephrine. The determination was accomplished by MEKC. The separation was carried out at 25 °C and 30 kV, using a 5 mM phosphate-5 mM borate buffer (pH=8.2), 40 mM SDS as background electrolyte. Under these conditions, the run time was 6.6 min and the limits of quantification were about 1.0 mg L^–1 for every component. Repeatability and reproducibility studies were achieved showing no significant differences at 95% confidence level. The MEKC method has been applied for quantifying these compounds in different commercials pharmaceuticals products, without separations steps.     

Determination of Phenolic Acids in Herba Epilobi by ITP–CE in the Column-Coupling Configuration

The combination of capillary isotachophoresis (ITP) and capillary zone electrophoresis (CZE) in the column-coupling configuration has been optimized in a mode in which the background electrolyte employed in the CZE step was different from the leading and terminating electrolytes of the ITP step. The optimum composition of the electrolyte system was 0.01 M HCl, 0.02 M IMI, 0.2% HEC, pH 7.2 (leading electrolyte), 0.01 M HEPES, pH 8.2 (terminating electrolyte), and 25 mM MES, 50 mM TRIS, 30 mM boric acid, 0.2% HEC, pH 8.3 (background electrolyte). All solutions contained 20% methanol. The timing of the transfer of isotachophoretically stacked analyte zones into the CZE column was also optimized. An ITP–CZE method with UV detection at 270 nm was developed for separation of nine phenolic acids (protocatechuic, syringic, vanillic, cinnamic, ferulic, caffeic, ρ-coumaric, chlorogenic, and gentisic acids) in a model mixture and used for assay of some of these acids in a methanolic extract of herba epilobi. Application of ITP–CZE resulted in 100-fold better sensitivity than conventional CZE; limits of detection ranged between 10 and 60 ng mL⁻¹. When MES–TRIS–borate-based buffer, pH 8.3, was used in the CZE separation step the linearity of the ITP–CZE response was satisfactory (correlation coefficients were from 0.9937 to 0.9777). Repeatability was also satisfactory (RSD values ranged between 0.77% and 1.28% for migration times and between 1.65% and 13.69% for peak area). Revised: 23 March and 27 April 2006