The effects of photo-degradation on the electrical properties of poly(ethylene terephthalate)

Poly(ethylene terephthalate) (PET) films have been exposed to uvradiation. Electrical property changes which occur in the films were examined. It was found that the relative dielectric constant and the dielectric strength decrease, while the dielectric loss factor increases. The rate of change of these parameters slowed down as the irradiation time increased. The parameter changes are presented graphically as a function of irradiation time and empirical equations are established. These empirical equations were obtained as second or third order polynomials by the least squares analysis method. The method of function straightening gave simpler power or exponential functions. These empirical equations represent the relationships between the electrical parameters and the irradiation time to a limit of relative error of less than 10%.     

The study on grafting comonomer of n-butyl acrylate and styrene onto poly(ethylene terephthalate) film by gamma-ray induced graft copolymerization

Poly(ethylene terephthalate) (PET) film was successfully grafted with n-butyl acrylate and styrene comonomer through gamma-ray induced graft copolymerization. The degree of grafting (DG) and the composition of grafted side chain were characterized by ¹H NMR. It was found that St can inhibit the homopolymerization of BA effectively and increase the DG when the concentration of comonomer mixture is kept constant. The proportion of St to BA in grafted side chain has a positive dependence on the feed ratio of St, which ultimately approaches the feed ratio. The thermal properties of poly(ethylene terephthalate)-graft-poly(n-butyl acrylate-co-styrene) (PET-g-P(BA-co-St)) films were investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The T_g of PET decreases with the DG, indicating that the grafted P(BA-co-St) copolymer has good compatibility with PET backbone.     

Deposition of Ethylene-Hexafluoropropene Gradient Plasma-Copolymer Using Dielectric Barrier Discharge Reactor at Atmospheric Pressure: Application to Release Coatings on Pressure-Sensitive Tape

Plasma-polymerized hexafluoropropene (PPHFP) film deposited using a dielectric barrier discharge reactor at atmospheric pressure had low enough adhesive strength, 22.2 Nm^–1, for use as a release coating of pressure-sensitive adhesive tapes, but the bond strength between PPHFP film and a poly (ethylene terephthalate) (PET) substrate film was slightly weak: some part of the PPHFP deposits could be peeled from the PET substrate. Since the XPS results indicated that the bond strength between plasma-polymerized ethylene (PPE) film and PET substrate was strong enough, we tried to deposit PPE and plasma-polymerized ethylene - hexafluoropropene gradient plasma-copolymer between the PET substrate and the PPHFP film. This multi-layer film (MLF) had low enough adhesive strength, 36.6 Nm^–1, for use as the release coating; this value was near that of a control sample, Teflon sheet, 21.6 Nm^–1. Moreover, the bond strength between MLF and PET substrate became stronger than that between PPHFP and PET films.     

Mechanical property studies of poly(ethylene terephthalate) crystallized by nonreactive liquids

The mechanical properties of initially amorphous, unoriented poly(ethylene terephthalate) (PET) films crystallized in acetone and dioxane at room temperature were studied under tensile testing conditions. It was found that the nature of the liquid, the morphology it induced, and its significant residual level trapped within the PET following this type of crystallization all influenced the observed mechanical behavior. Further, thermally treating PET at 70, 90, and 174°C prior to the liquid treatments appeared to inhibit the effects of the liquids on the resultant mechanical behavior. Finally, because these liquids penetrated the polymer as distinct fronts, laminate-type structures were generated in the films. It then was shown that an ideal parallel element laminate could adequately model the mechanical behavior of the films.     

Effect of biaxial orientation on dielectric and breakdown properties of poly(ethylene terephthalate)/poly(vinylidene fluoride‐co‐tetrafluoroethylene) multilayer films

Polymer films with enhanced dielectric and breakdown properties are essential for the production of high energy density polymer film capacitors. By capitalizing on the synergistic effects of forced assembly nanolayer coextrusion and biaxial orientation, polymer multilayer films using poly(ethylene terephthalate) (PET) and a poly(vinylidene fluoride‐co‐tetrafluoroethylene) [P(VDF‐TFE)] copolymer were produced. These films exhibited breakdown fields, under a divergent field using needle/plane electrodes, as high as 1000 kV mm^?1. The energy densities of these same materials, under a uniform electric field measured using plane/plane electrodes, were as high as 16 J cm^?3. The confined morphologies of both PET and P(VDF‐TFE) were correlated to the observed breakdown properties and damage zones. On‐edge P(VDF‐TFE) crystals induced from solid‐state biaxial stretching enhanced the effective P(VDF‐TFE) layer dielectric constant and therefore increased the dielectric contrast between the PET and P(VDF‐TFE) layers. This resulted in additional charge buildup at the layer interface producing larger tree diameters and branches and ultimately increasing the breakdown and energy storage properties. In addition to energy storage and breakdown properties, the hysteresis behavior of these materials was also evaluated. By varying the morphology of the P(VDF‐TFE) layer, the low‐field dielectric loss (or ion migration behavior) could be manipulated, which in turn also changed the observed hysteresis behavior. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 882–896     

Low-frequency glow discharge treatment of amorphous poly(ethylene terephthalate) films

The influence of treatment in a low-frequency glow discharge on the surface properties of an amorphous poly(ethylene terephthalate) (PET) film was studied. It was shown that, at identical external discharge parameters, changes in the wettability of plasma-treated PET films depended on its morphological structure—the amorphous film had higher values of the contact angle and lower values of the surface charge density than a biaxially oriented poly(ethylene terephthalate) of the PET-E brand.     

一种新的绝缘膜——聚对苯二甲酸对氧代苯甲酸乙二酯

聚对苯二甲酸乙二酯（匹T）膜已广泛用于绝缘和包装行业，其耐热温度不超过12O℃，熔点较高（260“C），结晶速率较快，难以拉制成电机槽绝缘和相绝缘所需厚度大于020mm的柔软薄膜．在PET的分子链中引人4，4’一氧代二次苯基能降低共聚酯的熔点［’j，但对共聚酯的热稳定性和结晶速率有无影响未曾提及．我们以4，4’一二苯醚二甲酸（OBBA）为改性组分，合成了一系列聚对苯二甲酸对氧代苯甲酸乙二酯（PETO）并制成薄膜，该膜不仅比PET膜的熔点低，结晶速率慢，而且热稳定性也有所提高，有可能制得0．2mm厚的薄膜．1实验部分1．l原料对…     

Effects of initial morphology and molecular weight on the deformability of poly(ethylene terephthalate)

Solution-grown crystal (SGC) mats and solution-cast (SC) films of poly(ethylene terephthalate) (PET) were drawn by solid-state coextrusion followed by tensile drawing of the coextrudates. Drawabilities and properties of the drawn films, such as mechanical and thermal properties, were investigated as functions of molecular weight, initial morphology, and drawing conditions. The initial morphology and molecular weight have a marked effect on the drawability and tensile properties of the resultant drawn films. The attainable maximum draw ratio increases with increasing molecular weight, and the highest draw ratio of 11.5 can be achieved by two-stage drawing of SC films prepared from pellets with an intrinsic viscosity of 1.43 dl/g. Such highly drawn films exhibit a tensile modulus of 17.5 GPa and strength at break of 400 MPa. These values are comparable to those obtained in conventional spinning of standard grade PET. At a given draw ratio, the tensile strength of the drawn films increases with increasing molecular weight, but the molecular weight dependence is not so marked in the tensile modulus as in the tensile strength. At a given molecular weight, the drawability of SGC mats is lower than that for SC films; however, the efficiency of drawing is higher for the former than for the latter. The difference may arise from the difference in crystallinity and/or crystal perfection of predrawn samples.     

Branching and cross-linking of poly(ethylene terephthalate) and its foaming properties

The branching and cross-linking of poly(ethylene terephthalate) were investigated using two chain extenders: glycidyl methacrylate-styrene copolymer (GS) and poly(butylene terephthalate)-GS (PBT-GS) in order to improve the melt viscosity and melt strength of poly(ethylene terephthalate). An obvious increase in torque evolution associated with chain extending, branching and cross-linking was observed during the process. The properties of modified poly(ethylene terephthalate) were characterized by intrinsic viscosity and insoluble content measurements, rheological and thermal analysis. The intrinsic viscosity and rheological properties of modified PET were improved significantly when using PBT-GS, indicating that PBT-GS should be a better chain extender. Good foaming of poly(ethylene terephthalate) materials were obtained using supercritical CO₂ as blowing agent. The average cell diameter and cell density were 61 μm and 1.8 × 10⁸ cells/cm³, respectively.     

Transitions/relaxations in polyester adhesive/PET system

The correlations between the transitions and the dielectric relaxation processes of the oriented poly(ethylene terephthalate) (PET) pre-impregnated of the polyester thermoplastic adhesive have been investigated by differential scanning calorimetry (DSC) and dynamic dielectric spectroscopy (DDS). The thermoplastic polyester adhesive and the oriented PET films have been studied as reference samples. This study evidences that the adhesive chain segments is responsible for the physical structure evolution in the PET-oriented film. The transitions and dielectric relaxation modes’ evolutions in the glass transition region appear characteristic of the interphase between adhesive and PET film, which is discussed in terms of molecular mobility. The storage at room temperature of the adhesive tape involves the heterogeneity of the physical structure, characterized by glass transition dissociation. Thus, the correlation between the transitions and the dielectric relaxation processes evidences a segregation of the amorphous phases. Therefore, the physical structure and the properties of the material have been linked to the chemical characteristics.     

Improvement of thermo-oxidative stability of electrically insulating polymeric materials by organic-inorganic hybrid coating

The thermo-oxidative stability of poly(ethylene terephthalate) (PET) and low-density polyethylene (LDPE) films, coated with organic-inorganic hybrid coatings of various compositions, has been investigated after accelerated ageing tests, in order to ascertain a possible beneficial effect of these coatings on the electrical performances of these insulating materials. The results have shown that the coating affects degradation mechanisms for both LDPE and PET.Thermo-oxidation is slow in LDPE, leading to significantly better insulating characteristics after ageing: a strong reduction of the embrittlement time was also observed.The strong increase of crystallinity upon ageing, observed for both coated and uncoated PET samples, probably dominates the effect of ageing on the electrical properties. As a consequence, only slight beneficial effects on PET electrical performances have been observed (both on conductivity and electrical strength). On the other hand, the coating has a strong effect on molecular weight changes leading to a significant increase of molecular weight for coated PET, while uncoated PET undergoes a significant decrease. This suggests that coated PET should present significantly better properties upon very long times of ageing.     

Processing of high density polyethylene and poly(ethylene terephthalate) blends

Commercial grades of high density polyethylene, HDPE and waste poly(ethylene terephthalate), PET were melt blended over a wide range of compositions. Effect of ethylene acrylic acid copolymer, EAA, ethylene vinyl acetate copolymer, EVA and maleic anhydride grafted EVA as compatibilizers on rheology and mechanical properties of the blend was studied. EAA was found most suitable compatibilizer.     

Oxygen barrier properties of crystallized and talc‐filled poly(ethylene terephthalate)

The improvement in oxygen barrier properties of poly(ethylene terephthalate) (PET) by incorporation of an impermeable phase such as crystallinity or talc platelets was examined. Crystallinity was induced by crystallization from the glassy state (cold crystallization). Microlayering was used to create talc‐filled structures with controlled layer architecture. The reduction of permeability in crystallized and talc‐filled PET was well described by Nielsen's model. Changes in permeability of crystalline PET could not be ascribed to the filler effect of crystallites only. Our data on solubility, obtained on the basis of measurements of the oxygen transport coefficients, confirmed a previous finding that the amorphous phase density of PET decreases upon crystallization. The data were amenable to interpretation by free volume theory. Talc‐filled materials processed by different methods showed the same permeability; however, much better mechanical properties were achieved by microlayering. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 847–857, 1999     

十二烷基硫酸钠对多壁碳纳米管/聚对苯二甲酸乙二酯复合材料性能的影响

用十二烷基硫酸钠(SDS)作为一种改性剂处理多壁碳纳米管(MWCNT),SDS处理后的MWCNT命名为SCNT,并采用微型挤出机和微型注塑机分别制备了MWCNT/PET和SCNT/PET复合材料.从材料的微观结构,导电性能,结晶性能和机械性能等角度,研究了SDS对MWCNT/PET复合材料性能的影响.结果表明,SDS处...     

1,2-丁二醇共聚对聚对苯二甲酸乙二醇酯结晶行为及力学性能的影响

为了探索生物基乙二醇中的1,2-丁二醇(1,2-BDO)作为共聚单体对生物基聚对苯二甲酸乙二醇酯(PET)的结晶行为和力学性能的影响。 本文合成了生物基PET均聚物和不同1,2-BDO共聚单元摩尔分数的系列生物基PET共聚物(共聚单体摩尔分数分别为2.0%、2.7%和5.6%),并采用傅里叶变换红外光谱仪(FTIR)、差示扫描量热仪(DSC)和力学测试等技术手段研究了其结晶行为和力学性能。 结果表明,随着1,2-BDO共聚单元摩尔分数的增加,PET共聚物的熔融温度、结晶速率及结晶度均明显降低,表明1,2-BDO共聚单体的引入破坏了PET分子链的规整性,阻碍了PET链段的结晶。 PET材料的拉伸强度随着1,2-BDO共聚单元摩尔分数的增加而降低,而弯曲强度和弯曲模量略有升高。     

Structure and properties of compatibilized recycled poly(ethylene terephthalate)/linear low density polyethylene blends

Blends of recycled poly(ethylene terephthalate) (R-PET) and linear low density polyethylene (LLDPE) were compatibilized with poly(styrene-ethylene/butyldiene-styrene) (SEBS) and maleic anhydride-grafted poly(styrene-ethylene/butyldiene-styrene) (SEBS-g-MA). Effects of compatilizer were evaluated systematically by study of mechanical, thermal and morphology properties together with crystallization behavior of PET. Tensile properties of the blends were improved effectively by the addition of 10 wt% SEBS-g-MA, elongation at break and charpy impact strength were increased with the increasing content of compatilizer. SEBS-g-MA is more effectual on mechanical properties of R-PET/LLDPE blends than SEBS. DSC analysis illustrates crystallinities of PET and LLDPE were increased by compatilizer at annealing condition. WAXD and FT-IR spectra show that annealing influences crystallization behavior of PET. Different compatilizer content results in different morphology structure, in particular, higher SEBS-g-MA content can induce the formation of a salami microstructure.     

高特PET-PBT共混单丝的结构与性能

采用一定比例的聚对苯二甲酸丁二醇酯(PBT)对聚对苯二甲酸乙二醇酯(PET)进行共混改性纺制大直径单丝,通过对共混单丝的力学性能、扫描电子显微镜及热性能分析,研究了共混比例、后拉伸工艺对共混物的相容性和拉伸强度的影响.结果表明:通过PET-PBT共混,提高了单丝的勾结强度;液体冷却温度、拉伸倍率及拉伸温度是影响共混单丝...     

Relaxation behavior of poly(ethylene terephthalate)/poly(ethylene naphthalene 2,6‐dicarboxylate) blends prepared by cryogenic blending

A method including cryogenic grinding, melt pressing from the molten state, and quenching was used to prepare blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) in which the two phases were highly dispersed. The effect of melt‐pressing times on the thermal properties and relaxation behavior of PET/PEN films were characterized with differential scanning calorimetry and dielectric spectroscopy. For short melt‐pressing times, two glass‐transition, two crystallization, and two melting peaks were observed, indicating the presence of PET‐rich and PEN‐rich phases in these blends. Longer melt‐pressing times revealed a single glass transition and a single α‐relaxation process, showing that PET–PEN block copolymers were likely to be formed during the melt pressing. The experimental findings were examined in terms of the transesterification reactions between the blend components, as revealed by ¹H NMR measurements. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2570–2578, 2002     

Preparation, characterization and dielectric properties of 4,4-diphenylmethane diisocyanate (MDI) based cross-linked polyimide films

Four different types of cross-linked polyimides based on 4,4-diphenylmethane diisocyanate (MDI) were prepared by the reaction of different types of conventional poly(amic acid) intermediates with MDI as a cross-linking agent. Subsequently, they were thermally imidized in order to obtain corresponding cross-linked polyimide structure. The results of FTIR-ATR showed that MDI can effectively react with carboxylic acid groups of PAA to form cross-linked polyimide films. TGA, FTIR-ATR and SEM analyses were carried out for characterization of cross-linked polyimide (CPI) films. Moreover, the electrical properties such as dielectric breakdown strength, dielectric constant, I-V characteristics and loss factor of MDI based cross-linked polyimides have been checked. In addition, some physical properties such as water uptake, adhesion, hardness and solubility properties of the films were investigated.The results showed that all CPI films have good insulating properties such as high dielectric breakdown voltage, low loss factor (tan δ), leakage density and excellent physical properties.     

Towards first-principles modelling of the mechanical properties of oriented poly(ethylene terephthalate)

This paper presents a procedure for simulating the anisotropic small-strain mechanical properties of oriented amorphous poly(ethylene terephthalate) (PET) starting from an atomistic level. A technique for producing oriented amorphous simulation cells of glassy PET has been developed and closely examined against related structural and property measurement data. The simulated elastic constants of these cells, derived by energy minimisation and molecular dynamics strain fluctuation methods, show encouraging agreement with experimental data.