Highly oriented (1 0 0) ZnO thin films by spray pyrolysis

Undoped ZnO thin films have been deposited onto glass substrates by spray pyrolysis. The structural, electrical and optical properties were studied on thin films, prepared from precursor solutions with varying the ethanol concentrations. X-ray diffraction studies have shown polycrystalline nature of the films with a hexagonal wurtzite-type structure. The preferential orientation plane (1 0 0) of the ZnO thin film is found to be sensitive to ethanol concentration. The texture coefficient (TC) and grain size value have been calculated. Also ethanol concentration was found to have significant effect on sheet resistivity of the films.     

GaN/LiNbO3 (0 0 0 1) interface formation calculated from first-principles

The stable adsorption sites for both Ga and N ions on the ideal and on the reconstructed LiNbO₃ (0 0 0 1) surface are determined by means of first-principle total energy calculations. A single N layer is found to be more strongly bound to the substrate than a single Ga layer. The adsorption of a GaN monolayer on the polar substrate within different orientations is then modeled. On the basis of our results, we propose a microscopic model for the GaN/LiNbO₃ interface. The GaN and LiNbO₃ (0 0 0 1) planes are parallel, but rotated by 30° each other, with in-plane epitaxial relationship [1 0 0]_GaN‖ [1 1  0]_LiNbO3. In this way the (0 0 0 1) plane lattice mismatch between GaN and LiNbO₃ is minimal and equal to 6.9% of the GaN lattice constant. The adsorbed GaN and the underlying LiNbO₃ substrate have parallel c-axes.     

Crystallographic symmetry effect on the nucleation in non-equilibrium aggregation pattern

Some non-equilibrium patterns formed in different systems are composed by crystallites with correlations in their crystallographic orientation. This reflects the fact that crystallographic symmetry controls the successive nucleation in the crystallite aggregating process. Based on the crystallographic symmetry, a new classification to describe the different kinds of anisotropy for non-equilibrium aggregation pattern has been proposed: parallel aggregation, twin aggregation and radial (random) aggregation. This new classification can clarify the different anisotropy related to the crystal point group, which the previous classifications cannot. The nucleation mechanisms for these three kinds of patterns are also discussed based on the symmetric relationship among the crystallites. It is shown that the crystallographic symmetry plays an important role not only on the crystal polyhedral shape formed by growth, but also on the aggregation pattern formed by nucleation.     

Thermal stability study of palladium and cobalt Schottky contacts on n-Ge (1 0 0) and defects introduced during contacts fabrication and annealing process

Palladium (Pd) and cobalt (Co) Schottky barrier diodes were fabricated on n-Ge (1 0 0). The Pd-Schottky contacts were deposited by resistive evaporation while the Co-contacts were deposited by resistive evaporation and electron beam deposition. Current-voltage (I-V), capacitance-voltage (C-V) and deep level transient spectroscopy (DLTS) measurements were performed on as-deposited and annealed samples. Electrical properties of Pd and Co samples annealed between 30 and 600 °C indicate the formation of one phase of palladium germanide and two phases of cobalt germanide. No defects were observed for the resistively evaporated as-deposited Pd-and Co-Schottky contacts. A hole trap at 0.33 eV above the valence band was observed on the Pd-Schottky contacts after annealing at 300 °C. An electron trap at 0.37 eV below the conduction band and a hole trap at 0.29 eV above the valence band was observed on as-deposited Co-electron beam deposited Schottky contacts. Rutherford back scattering (RBS) technique was also used to characterise the Co-Ge, for as-deposited and annealed samples.     

Mixed layer formation of copper overlayers on Ni(1 1 0) surface

Copper overlayer formation on the Ni(1 1 0) surface was studied by scanning tunneling microscopy (STM) in an ultrahigh vacuum. Atom-resolved STM images showed that initially deposited Cu is replaced with surface Ni atoms forming atom-size depressions on the Ni(1 1 0) terraces and a Ni-rich quasi-one-dimensional island along the direction. Further Cu deposition yields a mosaic structure on the islands, indicating Cu/Ni mixed layer formation. From the quantitative measurement of the Cu/Ni ratio on the substrate and the islands, impinging Cu will be replaced with surface Ni whereas expelled Ni and directly impinging Cu to the island form the mixed island. The number of Cu atoms in the islands, however, more than the directly impinging Cu, indicate significant Cu/Ni replacement at the periphery of the island.     

Elaboration of (1 1 1)-oriented La-doped PZT thin films on platinized silicon substrates

PLZT thin films with different thickness were deposited in situ on platinum coated silicon substrates using a multi-target sputtering system. The purpose was to grow (1 1 1)-textured PLZT films on Pt (1 1 1). To this aim, the role of some key parameters on both crystalline quality and electrical properties was investigated. An ultra-thin TiO₂ seeding layer was deposited, prior to PLZT, which strongly affected the crystallographic orientation of the films. The relation between temperature deposition and film crystallinity is analysed. TEM observations show the presence of some very small grains of Zr_0.9La_0.1O_1.95 at the film bottom interface. In the range of thickness investigated, the plot of the inverse capacitance as a function of the film thickness split up into two different curves, each with a linear shape, which however allows determination of a single value of interface capacitance. Above a thickness of 400-500 nm a saturation of the dielectric properties seems to be reached.     

Texture control of Pb(Zr, Ti)O3 thin films with different post-annealing processes

The non-crystalline Pb(Zr, Ti)O₃ thin films sputtered on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates at room temperature were crystallized by conventional furnace annealing (CFA) and rapid thermal annealing (RTA), respectively. It was found that the RTA process favored the (1 1 1)-preferred orientation in lead zirconate titanate (PZT) thin films while the CFA process favored the (1 0 0)-preferred orientation. The origin of the different orientation selection might be due to the different epitaxial nucleation mechanism. The long heating duration would lead to the aggregation of Pb and the formation of PbO(1 0 0) on film surface; therefore, the nucleation at the PbO(1 0 0)/PZT interface on film surface might lead to the (1 0 0)-preferred orientation. However, the nucleation at the PZT/Pt(1 1 1) electrode interface by RTA process would result in the formation of (1 1 1)-preferred orientation. The RTA-derived (1 1 1)-preferentially oriented PZT thin films exhibited a high remnant polarization of 35 μC/cm².     

Growth of Ag thin films on ZnO(0 0 0 −1) investigated by AES and STM

The growth of Ag films on ZnO(0 0 0 −1) has been investigated by Auger electron spectroscopy (AES) and scanning tunneling microscopy (STM). A high density of islands is nucleated at the earliest stages of the growth. An upstepping mechanism causes these islands to coalesce while the uncovered fraction of the ZnO surface remains constant (30%).     

ZnO thin films on Si(1 1 1) grown by pulsed laser deposition from metallic Zn target

ZnO thin films with highly c-axis orientation have been fabricated on p-type Si(1 1 1) substrates at 400 °C by pulsed laser deposition (PLD) from a metallic Zn target with oxygen pressures between 0.1 and 0.7 mbar. Experimental results indicate that the films deposited at 0.3 and 0.5 mbar have better crystalline and optical quality and flatter surfaces than the films prepared at other pressures. The full width at half maximum (FWHM) of (0 0 0 2) diffraction peak decreases remarkably from 0.46 to 0.19° with increasing annealing temperature for the film prepared at 0.3 mbar. In photoluminescence (PL) spectra at room temperature, the annealed film at 700 °C exhibits a smaller ultraviolet (UV) peak FWHM of 108 meV than the as-grown film (119 meV). However, an enhanced deep-level emission is observed. Possible origins to above results are discussed.     

Microstructural and surface characterization of thin gold films on n-Ge (1 1 1)

Thin gold films were fabricated by vacuum resistive deposition on the n-Ge (1 1 1) wafers. The films were annealed between 300 and 600 °C. These resulting thin films were then characterised using scanning electron microscopy (field emission and back-scattering modes), Rutherford back scattering spectroscopy and time of flight secondary ion mass spectroscopy (TOF-SIMS). For temperatures below the eutectic temperature the distribution of both the gold and the germanium on the surface are uniform. Above the eutectic temperature, the formation of gold rich islands on the surface of the Germanium were observed. These changes in the microstructure were found to correspond to changes in the electrical characteristics of the diodes.     

Morphology of pentacene films deposited on Cu(1 1 9) vicinal surface

We investigate the morphology of a pentacene (C₂₂H₁₄) film adsorbed on the Cu(1 1 9) vicinal surface by scanning tunnelling microscopy (STM). Thermal treatment of a thick film of molecules generates a long-range ordered structure. Series of molecular rows are alternated with areas where the molecules assume two equivalent orientations. STM data analysis suggests that the ordered structure can be described by a rippled morphology. The behaviour of the film at different annealing temperatures suggests a possible explanation of the film structure as due to an adsorbate-induced modification of the substrate.     

Surface treatments toward obtaining clean GaN(0 0 0 1) from commercial hydride vapor phase epitaxy and metal-organic chemical vapor deposition substrates in ultrahigh vacuum

We studied processes of cleaning GaN(0 0 0 1) surfaces on four different types of wafers: two types were hydride vapor phase epitaxy (HVPE) free-standing substrates and two types were metal-organic chemical vapor deposition (MOCVD) films grown on these HVPE substrates and prepared by annealing and/or Ar ion sputtering in ultra high vacuum. We observed the surfaces through treatments using in situ low-energy electron diffraction (LEED), reflection high-energy electron diffraction (RHEED), scanning tunneling microscopy (STM), and Auger electron spectroscopy, and also using ex situ temperature programmed desorption, X-ray photoelectron spectroscopy, X-ray diffraction, and secondary ion mass spectrometry. For HVPE samples, we obtained relatively clean surfaces under optimized three-step annealing conditions (200 °C for 12 h + 400 °C for 1 h + 500 °C for 5 min) without sputtering, after which the surface contamination of oxide and carbide was reduced to ∼20% of that before annealing. Clear GaN(0 0 0 1)1×1 patterns were obtained by LEED and RHEED. STM images showed flat terraces of ∼10 nm size and steps of ∼0.5 nm height. Upon annealing the HVPE-GaN samples at a much higher temperature (C), three-dimensional (3D) islands with facets were formed and the surface stoichiometry was broken down with the desorption of nitrogen in the form of ammonia, since the samples include hydrogen as an impurity. Ar⁺ sputtering was effective for removing surface contamination, however, postannealing could not recover the surface roughness but promoted the formation of 3D islands on the surface. For MOCVD/HVPE homoepitaxial samples, the surfaces are terminated by hydrogen and the as-introduced samples showed a clear 1×1 structure. Upon annealing at 500-600 °C, the surface hydrogen was removed and a 3×3 reconstruction structure partially appeared, although a 1×1 structure was dominant. We summarize the structure differences among the samples under the same treatment and clarify the effect of crystal quality, such as dislocations, the concentration of hydrogen impurities, and the residual reactant molecules in GaN films, on the surface structure.     

Atypical grain growth for (2 1 1) CdTe films deposited on surface reconstructed (1 0 0) SrTiO3 substrates

The (1 0 0) SrTiO₃ substrate has emerged as the oxide substrate of choice for the deposition of a wide variety of materials. The substrate's unavoidable miscut leads to a step-terrace morphology when heated to high temperatures. This morphological transition is accompanied by an atomic scale repositioning of the uppermost terrace atoms, the nature of which is strongly dependent on the substrate temperature and ambient atmosphere used. Here, we report the deposition of CdTe films on the as-received and reconstructed surfaces of (1 0 0) SrTiO₃. The as-received substrate gives rise to a [1 1 1] CdTe film with four equally distributed in-plane grain orientations. The surface reconstruction, on the other hand, gives rise to an unprecedented reorientation of the film's grain structure. For this case, a [2 1 1] CdTe film emerges having twelve unevenly distributed in-plane orientations. We attribute the film's grain structure to an atomic scale surface reconstruction, with the anisotropic distribution of grain-types arising from a preferential formation due to the step edges.     

Structural and magnetic properties of evaporated Fe thin films on Si(1 1 1), Si(1 0 0) and glass substrates

We present experimental results on the structural and magnetic properties of series of Fe thin films evaporated onto Si(1 1 1), Si(1 0 0) and glass substrates. The Fe thickness, t, ranges from 6 to110 nm. X-ray diffraction (XRD) and atomic force microscopy (AFM) have been used to study the structure and surface morphology of these films. The magnetic properties were investigated by means of the Brillouin light scattering (BLS) and magnetic force microscopy (MFM) techniques. The Fe films grow with (1 1 0) texture; as t increases, this (1 1 0) texture becomes weaker for Fe/Si, while for Fe/glass, the texture changes from (1 1 0) to (2 1 1). Grains are larger in Fe/Si than in Fe/glass. The effective magnetization, 4πM_eff, inferred from BLS was found to be lower than the 4πM_S bulk value. Stress induced anisotropy might be in part responsible for this difference. MFM images reveal stripe domain structure for the 110 nm thick Fe/Si(1 0 0) only.     

Epitaxially grown ZnO thin films on 6H-SiC(0 0 0 1) substrates prepared by spin coating-pyrolysis

Epitaxially grown ZnO thin film on 6H-SiC(0 0 0 1) substrate was prepared by using a spin coating-pyrolysis with a zinc naphthenate precursor. As-deposited film was pyrolyzed at 500 °C for 10 min in air and finally annealed at 800 °C for 30 min in air. In-plane alignment of the film was investigated by X-ray pole-figure analysis. Field emission-scanning electron microscope, scanning probe microscope, and He-Cd laser (325 nm) was used to analyze the surface morphology, the surface roughness and photoluminescence of the films. In the photoluminescence spectra, near-band-edge emission with a broad deep-level emission was observed. The position of the near-band-edge peak was around 3.27 eV.     

Buffer effects of Ag layers on magneto-optical Co/Ge(1 0 0) ultrathin films

Magnetic properties of the Co/Ag/Ge(1 0 0) films grown at room temperature and 200 K were studied by the surface magneto-optical Kerr effect (SMOKE). More than 1.5 monolayer Ag buffer layers not only effectively block the interdiffusion between the capped Co layers and the Ge(1 0 0) substrate but also stabilize the magnetic phase. The temperature and thickness dependence on coercivity measurements show that interactions upon the interfaces are strongly correlated to the microstructures.     

Theoretical study of Ti and Fe surface alloys on Al(0 0 1) substrate

Accurate density-functional calculations are performed to investigate the formation of Ti and Fe ultrathin alloys on Al(0 0 1) surface. It is demonstrated that a deposition of Ti monolayer on Al(0 0 1) substrate leads to the formation of Al₃Ti surface alloy with Ti atoms arranged according to the L1₂ stacking, distinct from the D0₂₂ structure characteristic of a bulk Al₃Ti compound. A quest for the reason of this distinct atomic arrangement led us to the study of the surface structure of Al₃Ti(0 0 1) compound. It is concluded that even the Al₃Ti(0 0 1) surface is terminated with three layers assuming a L1₂ stacking and hence this stacking fault can be classified as a surface-induced stacking fault. Several possibilities of Fe atoms distributed in the surface region of Al(0 0 1) have been examined. The most stable configuration is the one with the compact Fe monolayer on Al(0 0 1) and covered by one Al monolayer. Lastly, our calculations show that there is no barrier for the penetration of Fe adatoms below the Al(0 0 1) surface; however, such a barrier is present for a Ti-alloyed Al(0 0 1) surface.     

Electrons in thin films

The method of evaluation of broken-symmetry Green’s function is presented. This method was applied to electron subsystem of a thin film. It was found that electron concentrations are spatially dependent and their spatial distribution proves the existence of skin effect. The skin effect is most expressed in the films of minimal thickness. The internal energy of electrons lying in the film Fermi volume, decreases with the increase of temperature. It is the consequence of the Pauli principle, which does not allow change of electron velocities. Introduced heat increases electron effective masses and this leads to the decrease of internal energy.     

Thickness dependence on thermal stability of sputtered Ag nanolayer on Ti/Si(1 0 0)

Thermal stability of Ag layer on Ti coated Si substrate for different thicknesses of the Ag layer have been studied. To do this, after sputter-deposition of a 10 nm Ti buffer layer on the Si(1 0 0) substrate, an Ag layer with different thicknesses (150-5 nm) was sputtered on the buffer layer. Post annealing process of the samples was performed in an N₂ ambient at a flow rate of 200 ml/min in a temperature range from 500 to 700 °C for 30 min. The electrical property of the heat-treated multilayer with the different thicknesses of Ag layer was examined by four-point-probe sheet resistance measurement at the room temperature. Phase formation and crystallographic orientation of the silver layers were studied by θ-2θ X-ray diffraction analysis. The surface topography and morphology of the heat-treated films were determined by atomic force microscopy, and also, scanning electron microscopy. Four-point- probe electrical measurement showed no considerable variation of sheet resistance by reducing the thickness of the annealed Ag films down to 25 nm. Surface roughness of the Ag films with (1 1 1) preferred crystallographic orientation was much smaller than the film thickness, which is a necessary condition for nanometric contact layers. Therefore, we have shown that the Ag layers with suitable nano-thicknesses sputtered on 10 nm Ti buffer layer were thermally stable up to 700 °C.     

Interaction of hydrogen with InN thin films elaborated on InP(1 0 0)

III-V semiconductor compound structures are widely applied in technology of advanced microelectronics, optoelectronics, and gas sensors. In this paper, we report on the use of XPS to characterize in situ the interaction of thermally activated hydrogen atoms and hydrogen molecules with InP(1 0 0) surfaces covered by thin InN overlayers. XPS spectra were taken with an ESCALAB-210 spectrometer after repeated hydrogenation cycles at temperatures up to 350 °C. The evolution of the In 3d, In 4d, P 2p, N 1s, O 1s and C 1s photoelectron spectra was carefully monitored. The XPS spectra of the hydrogen exposed surface revealed significant differences compared to those from the non-hydrogenated surface. InN films were found to be weakly reactive to hydrogen under experimental conditions explored. The behavior of P atoms at the hydrogenated surface was dependent on the parameters characterizing each hydrogenation (exposure, hydrogen species used, annealing temperature). Moreover, the heavily hydrogenated surface exhibited a phosphorus enrichment.