Optical characterization of PLD grown nitrogen-doped TiO2 thin films

Nitrogen-doped TiO₂ thin films were prepared by pulsed laser deposition (PLD) by ablating metallic Ti target with pulses of 248 nm wavelength in reactive atmospheres of O₂/N₂ gas mixtures. The layers were characterized by UV-VIS spectrophotometry and variable angle spectroscopic ellipsometry with complementary profilometry for measuring the thickness of the films. Band gap and extinction coefficient values are presented for films deposited at different substrate temperatures and for varied N₂ content of the gas mixture. The shown tendencies are correlated to nitrogen incorporation into the TiO_2-xN_x layers. It is shown that layers of significantly increased visible extinction coefficient with band gap energy as low as 2.89 eV can be obtained. A method is also presented how the spectroscopic ellipsometric data should be evaluated in order to result reliable band gap values.     

Influence of negative ion element impurities on laser induced damage threshold of HfO2 thin film

Negative ion element impurities breakdown model in HfO₂ thin film was reported in this paper. The content of negative ion elements were detected by glow discharge mass spectrum analysis (GDMS); HfO₂ thin films were deposited by the electron-beam evaporation method. The weak absorption and laser induced damage threshold (LIDT) of HfO₂ thin films were measured to testify the negative ion element impurity breakdown model. It was found that the LIDT would decrease and the absorption would increase with increasing the content of negative ion element. These results indicated that negative ion elements were harmful impurities and would speed up the damage of thin film.     

Al2O3/SiO2 films prepared by electron-beam evaporation as UV antireflection coatings on 4H-SiC

Al₂O₃/SiO₂ films have been deposited as UV antireflection coatings on 4H-SiC by electron-beam evaporation and characterized by reflection spectrum, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The reflectance of the Al₂O₃/SiO₂ films is 0.33% and 10 times lower than that of a thermally grown SiO₂ single layer at 276 nm. The films are amorphous in microstructure and characterize good adhesion to 4H-SiC substrate. XPS results indicate an abrupt interface between evaporated SiO₂ and 4H-SiC substrate free of Si-suboxides. These results make the possibility for 4H-SiC based high performance UV optoelectronic devices with Al₂O₃/SiO₂ films as antireflection coatings.     

Effects of H2 ambient annealing in fully 0 0 2-textured ZnO:Ga thin films grown on glass substrates using RF magnetron co-sputter deposition

Gallium doped zinc oxide (ZnO:Ga) thin films were grown on glass substrates using RF magnetron co-sputtering, followed by H₂ ambient annealing at 623 K to explore a possibility of steady and low-cost process for fabricating transparent electrodes. While it was observed that the ZnO:Ga thin films were densely packed c-axis oriented self-textured structures, in the as-deposited state, the films contained Ga₂O₃ and ZnGa₂O₄ which had adverse effect on the electrical properties. On the other hand, post-annealing in H₂ ambient improved the electrical properties significantly via reduction of Ga₂O₃ and ZnGa₂O₄ to release elemental Ga which subsequently acted as substitutional dopant increasing the carrier concentration by two orders of magnitude. Transmittance of the ZnO:Ga thin films were all over 90% that of glass while the optical band gap varied in accordance with the carrier concentrations due to changes in Fermi level. Experimental observation in this study suggests that transparent conductive oxide (TCO) films based on Ga doped ZnO with good electrical and optical properties can be realized via simple low-cost process.     

Ab initio calculation of optical absorption and reflectivity of Si(0 0 1)/SiO2 superlattices with varying interfaces

Using first-principles calculations we investigate the influence of interface modification and layer thicknesses on the optical properties of Si/SiO₂ superlattices. Four interface models with different dangling-bond passivation are considered. The results demonstrate confinement effects not only for the fundamental band gaps but also for the optical properties. While for a large Si layer thickness of the Si/SiO₂ superlattices the interface dependence is small, the calculations show a significant structure dependence for thin Si layers. © 2007 Elsevier Science. All rights reserved.     

AlF3 film deposited by IAD with end-Hall ion source using SF6 as working gas

A novel and effective process to fabricate high quality fluoride thin films was presented. Aluminum fluoride films deposited by a conventional thermal evaporation with an ion-assisted deposition (IAD) using SF₆ as a working gas at around room temperature were investigated. In this study, the optimal voltage and current, 50 V and 0.25 A, were found according to the optical properties of the films: high refractive index (1.489 at 193 nm), low optical absorption and extinction coefficient (<10⁻⁴ at 193 nm) in the UV range. The physical properties of the film are high packing density and amorphous without columnar structure. It was proved that using SF₆ working gas in IAD process is a good choice and significantly improves the quality of AlF₃ films.     

Thermal stability of Mo/Si multilayer soft-X-ray mirrors fabricated by electron-beam evaporation

Mo/Si multilayers are fabricated by electron-beam evaporation in UHV at different temperatures (30° C, 150° C, 200° C) during deposition. After completion their thermal stability is tested by baking them at temperatures (T _bak) between 200° C and 800° C in steps of 50° C or 100° C. After each baking step the multilayers are characterized by small angle Cu_K-X-ray diffraction. Additionally, the normal incidence soft-X-ray reflectivity for wavelengths between 11 nm and 19 nm is determined after baking at 500° C. Furthermore, the layer structure of the multilayers is investigated by means of Rutherford Backscattering Spectroscopy (RBS) and sputter/Auger Electron Spectroscopy (AES) technique. While the reflectivity turns out to be highest for a deposition temperature of 150° C, the thermal stability of the multilayer increases with deposition temperature. The multilayer deposited at 200° C stands even a 20 min 500° C baking without considerable changes in the reflectivity behaviour.     

Surface charging at the (1 0 0) surface of Cu doped and undoped Li2B4O7

We have compared the photovoltaic charging of the (1 0 0) surface termination for Cu doped and undoped Li₂B₄O₇. While the surface charging at the (1 0 0) surface of Li₂B₄O₇ is significantly greater than observed at (1 1 0) surface, the Cu doping plays a role in reducing the surface photovoltage effects. With Cu doping of Li₂B₄O₇, the surface photovoltaic charging is much diminished at the (1 0 0) surface. The density of states observed with combined photoemission and inverse photoemission remains similar to that observed for the undoped material, except in the vicinity of the conduction band edge.     

Gd-doping of HfO2

An increase in the density of states between the oxygen 2p bands and the Fermi level is seen with increasing Gd concentrations. In addition, for the Gd-doped HfO₂ films, the Gd 4f photoexcitation peak at 5.5 eV below the valence band maximum was identified using resonant photoemission. Electrical measurements show pronounced rectification properties for lightly-doped Gd:HfO₂ films on p-Si and for heavily-doped Gd:HfO₂ films on n-Si, suggesting a crossover from n-type to p-type behavior with increasing doping level. In addition, there is an increase in the reverse bias current with neutron irradiation.     

Growth of highly-oriented CaCu3Ti4O12 thin films on SrTiO3 (1 0 0) substrates by a chemical solution route

Highly-oriented CaCu₃Ti₄O₁₂ (CCTO) thin films deposited directly on SrTiO₃ (1 0 0) substrates have been developed successfully using a chemical solution coating method. X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) were employed to characterize the structure and the morphology. It was observed that the CCTO thin films had the 1 μm × 1 μm domain-like microstructure that consists of compact grains of about 0.1 μm in size. The cross sectional SEM image shows that the CCTO grains grow regularly close to the clear interface between the CCTO film and the SrTiO₃ substrate. The result was discussed in terms of lattice mismatch between CCTO and SrTiO₃.     

Superior refractive index tailoring properties in composite ZrO2/SiO2 thin film systems achieved through reactive electron beam codeposition process

Composite optical thin-film materials have received a significant amount of interest in order to relieve the material constraints on refractive indices as well as reducing the number of layers required in optical coating design. Amongst others binary zirconia-silica composite thin films have attracted considerable attentions due to their several favorable opto-mechanical properties. In the present studies such a composite system under certain compositional mixings displayed both refractive index and band gap supremacy over pure zirconia films violating the most popular Moss rule. This unexpected evolution has several practical applications one of which can be directly employed in extending the range of tunability of the refractive index. Besides, the probing of such a novel evolution through the analysis of ellipsometric refractive index modeling and morphological correlation functions has revealed several novel as well as superior microstructural properties in the composite thin film systems. All these characterization and analysis techniques distinctly indicate a strong interrelation between the microstructural ordering and superior optical properties of the present zirconia-silica codeposited composites.     

Epitaxially grown ZnO thin films on 6H-SiC(0 0 0 1) substrates prepared by spin coating-pyrolysis

Epitaxially grown ZnO thin film on 6H-SiC(0 0 0 1) substrate was prepared by using a spin coating-pyrolysis with a zinc naphthenate precursor. As-deposited film was pyrolyzed at 500 °C for 10 min in air and finally annealed at 800 °C for 30 min in air. In-plane alignment of the film was investigated by X-ray pole-figure analysis. Field emission-scanning electron microscope, scanning probe microscope, and He-Cd laser (325 nm) was used to analyze the surface morphology, the surface roughness and photoluminescence of the films. In the photoluminescence spectra, near-band-edge emission with a broad deep-level emission was observed. The position of the near-band-edge peak was around 3.27 eV.     

Preparation and spectroscopic properties of Nb2O5 nanorods

Nb₂O₅ nanorods have been prepared using water/ethanol media. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-visible absorption and photoluminescence spectroscopy. The as-prepared Nb₂O₅ nanorods appeared to be single pseudohexagonal (TT-Nb₂O₅) phase. From the photoluminescence spectrum, two emission bands at 407 and 496 nm, respectively, were observed. The origin of the luminescence was discussed in detail.     

Growth process of β-FeSi2 epitaxial film on Si(1 1 1) by molecular beam epitaxy

We have reported a one step growth of a high quality β-FeSi₂ epitaxial film on hydrogen terminated Si(1 1 1) by using molecular beam epitaxy (MBE) without template layer or post-growth annealing. In the present work, the growth process was studied by analyzing X-ray diffraction (XRD) spectra, reflective high energy electron diffraction (RHEED) and atomic force microscopy (AFM) observations on the samples grown with different growth times from 10 s to 1 h. A phase transformation from γ-FeSi₂ to β-FeSi₂ was confirmed existing in the crystal film growth, as well as the growth mode changing from three-dimensional (3D) to two-dimensional (2D) mode.     

Photoreflectance study of energy level structure of self-assembled InAs/GaAs quantum dots emitting at 1.3 μm

Photoreflectance and photoluminescence measurements were performed on the ensemble of self assembled InAs/GaAs quantum dots designed to emit at 1.3 μm. As many as six QDs-related optical transitions were observed in PR spectra, the energies of which were confirmed by high-excitation PL results. Numerical calculations allowed estimating the average size of the dots, which is larger than for standard InAs/GaAs QDs. This result is in agreement with structural data. Additionally, the energy level structure for such QDs was derived and compared with the electronic structure of standard InAs/GaAs dots. It was shown that the energy level structure of such large dots qualifies them for the active region of a laser emitting at 1.3 μm.     

The electric field modulation by lateral crack coated with HfO2/SiO2 high reflector

High-dielectric constant multilayer coatings are commonly used on optics to increase the laser damage resistance of optics. In this work, the three-dimensional finite-difference time-domain is improved to simulate the electric field intensity distribution in the silica–hafnia multilayer coatings on fused silica subsurface with lateral crack. Results reveal that as the substrate is defect-free, the largest intensification is at the surface layer, especially in the hafnia layer. As the lateral crack appears on the subsurface of fused silica, the intensified sites are mainly located at distorted coatings layers. Dependences of peak LIEF on crack's parameters are detailed investigated. Results show that laser intensification is more sensitive to its width, and the modulation of lateral defect with silica–hafnia multilayer is greater than nodular defect as its width larger than 5λ.     

Optical and structural studies on Ba(Mg1/3Ta2/3)O3 thin films obtained by radiofrequency assisted pulsed plasma deposition

Single-phase Ba(Mg_1/3Ta_2/3)O₃ thin films were prepared by radiofrequency plasma beam assisted pulsed laser deposition (RF-PLD) starting from a bulk ceramic target synthesized by solid state reaction. Atomic force microscopy, X-ray diffraction and spectroscopic ellipsometry were used for morphological, structural and optical characterization of the BMT thin films. The X-ray diffraction spectra show that the films exhibit a polycrystalline cubic structure. From spectroscopic ellipsometry analysis, the refractive index varies with the thin films deposition parameters. By using the transmission spectra and assuming a direct band to band transition a band gap value of ≈4.72 eV has been obtained.     

Fabrication, morphology, and photoluminescence properties of GaN nanowires and nanorods by ammoniating Ga2O3/V films on Si(1 1 1)

GaN nanowires and nanorods have been successfully synthesized on Si(1 1 1) substrates by magnetron sputtering through ammoniating Ga₂O₃/V films at 900 °C in a quartz tube. X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectrum were carried out to characterize the structure, morphology, and photoluminescence properties of GaN sample. The results show that the GaN nanowires and nanorods with pure hexagonal wurtzite structure have good emission properties. The growth direction of nanostructures is perpendicular to the fringes of (1 0 1) plane. The growth mechanism is also briefly discussed.     

Atypical grain growth for (2 1 1) CdTe films deposited on surface reconstructed (1 0 0) SrTiO3 substrates

The (1 0 0) SrTiO₃ substrate has emerged as the oxide substrate of choice for the deposition of a wide variety of materials. The substrate's unavoidable miscut leads to a step-terrace morphology when heated to high temperatures. This morphological transition is accompanied by an atomic scale repositioning of the uppermost terrace atoms, the nature of which is strongly dependent on the substrate temperature and ambient atmosphere used. Here, we report the deposition of CdTe films on the as-received and reconstructed surfaces of (1 0 0) SrTiO₃. The as-received substrate gives rise to a [1 1 1] CdTe film with four equally distributed in-plane grain orientations. The surface reconstruction, on the other hand, gives rise to an unprecedented reorientation of the film's grain structure. For this case, a [2 1 1] CdTe film emerges having twelve unevenly distributed in-plane orientations. We attribute the film's grain structure to an atomic scale surface reconstruction, with the anisotropic distribution of grain-types arising from a preferential formation due to the step edges.     

Effect of ion nitriding on the crystal structure of 3 mol% Y2O3-doped ZrO2 thin-films prepared by the sol-gel method

We investigated the effect of ion nitriding on the crystal structure of 3 mol% Y₂O₃-doped ZrO₂ (3YSZ) thin-films prepared by the sol-gel method. For this purpose, we used X-ray diffractometry to determine the crystalline phases, the lattice parameters, the crystal sizes, and the lattice microstrains, and glow discharge-optical emission spectroscopy to obtain the depth profiles of the elemental chemical composition. We found that nitrogen atoms substitute oxygen atoms in the 3YSZ crystal, thus leading to the formation of unsaturated-substitutional solid solutions with reduced lattice parameters and Zr_0.94Y_0.06O_1.72N_0.17 stoichiometric formula. We also found that ion nitriding does not affect the grain size, but does generate lattice microstrains due to the increase in point defects in the crystalline lattice.