Structure and magnetic properties of γ′-Fe4N films grown on MgO-buffered Si (0 0 1)

γ′-Fe₄N thin films were grown on MgO-buffered Si (1 0 0) by pulsed laser deposition technique. Different crystallographic orientations and in-plane magnetic anisotropies were achieved by varying the growth temperature of the MgO buffer layer. When the MgO buffer layer was grown at room temperature, the γ′-Fe₄N film shows isotropic in-plane magnetic properties without obvious texture; while in-plane magnetic anisotropy was recorded for the γ′-Fe₄N films deposited on a 600 °C-grown-MgO buffer due to the formation of a (1 0 0)-oriented biaxial texture. Such a difference in in-plane magnetic anisotropy is attributed to the epitaxial growth of γ′-Fe₄N film on an MgO buffer with relaxed strain when the MgO layer was grown at a high temperature of 600 °C.     

Influence of CuO and sintering temperature on the microstructure and magnetic properties of Mg–Cu–Zn ferrites

The synthesis of a series of Mg–Cu–Zn ferrites with the substitution of Cu for Mg has been obtained by solid-state reaction method. Microstuctural and structural analyses were carried out using a scanning electron microscope and X-ray diffraction (XRD), respectively. The lattice parameter is found to increase with increasing copper content. A remarkable densification is observed with the addition of Cu ions in the ferrites. Microstructural analyses indicate that CuO influences the microstructure of the ferrites by the formation of liquid phase during sintering. The grain size significantly increases with increasing copper content. Exaggerated grain growth is observed for the samples of x=0.25–0.35. The initial magnetic permeability (μ′) increases sharply with increasing concentration of Cu ions. This increase in μ′ is explained with the grain growth mechanism and enhanced densification of the ferrites. The resonance frequency of all the samples shifts toward the lower frequency as the permeability increases with Cu content. Sintering temperature T_s also affects the densification, grain growth and initial magnetic permeability of the samples.     

Influence of manganese substitution and annealing temperature on the formation,microstructure and magnetic properties of Mn–Zn ferrites

The effects of annealing temperature and manganese substitution on the formation, microstructure and magnetic properties of Mn_xZn_1−xFe₂O₄ (with x varying from 0.3 to 0.9) through a solid-state method have been investigated. The correlation of the microstructure and the grain size with the magnetic properties of Mn–Zn ferrite powders was also reported. X-ray diffraction (XRD), a scanning electron microscope (SEM) and a vibrating sample magnetometer (VSM) were utilized in order to study the effect of variation of manganese substitution and its impact on crystal structure, crystalline size, microstructure and magnetic properties of the ferrite powders formed. The XRD analysis showed that pure single phases of Mn–Zn ferrites were obtained by increasing the annealing temperature to 1200–1300 °C. Increasing the annealing temperature to ?1300 °C led to abnormal grain growth with inter-granular pores and this led to a decrease in the saturation magnetization. Moreover, an increase in the Mn²⁺ ion substitution up to x=0.8 increased the lattice parameter of the formed powders due to the high ionic radii of the Mn²⁺ ion. Mn–Zn ferrites phases were formed and the positions of peaks were shifted by substituting manganese. The average crystalline size was increased by increasing the annealing temperature and decreased by increasing the substitution by manganese up to 0.8. The average crystalline size was in the range 95–137.3 nm. The saturation magnetization of the Mn–Zn-substituted ferrite powders increased continuously with an increase in the Mn concentration up to 0.8 at annealing temperatures of 1200–1300 °C. Further increase of Mn substitution up to 0.9 led to a decrease of saturation magnetization. The saturation magnetization increased from 17.3 emu/g for the Mn_0.3Zn_0.7Fe₂O₄ phase particles produced to 59.08 emu/g for Mn_0.8Mn_0.2Fe₂O₄ particles.     

Influence of annealing on microstructure and magnetic-transport of FeCo–SiO2 nanogranular films

A series of FeCo–SiO₂ nanogranular films were prepared using magnetron controlled sputtering method. The microstructure, tunneling giant magnetoresistance (TMR) and magnetic properties of FeCo–SiO₂ films deposited at room temperature and then annealed at various temperatures were investigated using transmission electron microscopy (TEM), conventional four probes method and vibrated sample magnetometer (VSM) under room temperature, respectively. The results showed that all FeCo–SiO₂ films consisted of FeCo granules with equiaxial shape uniformly dispersed in the SiO₂ matrix and formed body-centered cubic (bcc) structure. With increasing the annealing temperature, FeCo granule size increased monotonically. For film with 30.5 vol% FeCo, the size distribution satisfied the log-normal function at lower annealing temperature. While with increasing annealing temperature, the size distribution deviated gradually from the log-normal function. Meanwhile, upon varying the annealing temperature, the TMR of films with lower volume fraction reached a peak value at higher annealing temperature and the TMR of films with higher volume fraction reached a peak value at lower annealing temperature. In addition, the results also indicated that the sensitivity of TMR changed non-monotonically with the increment of the annealing temperature and both the saturation magnetization and the susceptibility of FeCo (30.5 vol%)–SiO₂ films increased with increasing the annealing temperature.     

The microstructure and magnetic properties of electrodeposited Co–Pt thin films on Ru buffer layer

For high-density magnetic recording media, this study examined the crystal structure and the texture of electrodeposited cobalt–platinum (Co–Pt) films on Ru buffer layer. A 15-nm-thick Co–Pt film exhibited very high out-of-plane coercivity and squareness, which were 6248 Oe and 0.89, respectively. The coercivity, H_c, of Co–Pt films grown on Ru buffer layer decreased significantly with increasing thickness, possibly due to the lattice misfit of 5.4% between Co–Pt and Ru, leading to the decrease of perpendicular magnetic anisotropy (PMA) of Co–Pt films as indicated by the observed hexagonal-closed-packed (HCP) (1 1¯ 0 1) plane of Co–Pt films. According to nano beam diffraction pattern (NBDP), however, Co–Pt film grown on Ru layer of HCP exhibited mixed HCP and FCC phases. Also, cross-sectional TEM image suggests that the high PMA may result from the columnar structure of physically isolated Co–Pt grains with the c-axis perpendicular to the film plane.     

Influence of γ-irradiation on the optical parameters of 4-tricyanovinyl-N,N-diethylaniline thin films

Thin films of 4-tricyanovinyl-N,N-diethylaniline (TCVA) were prepared by thermal evaporation technique. The spectral and the optical parameters have been investigated by using the spectrophotometric measurements of both transmittance and reflectance at normal incidence of light in the wavelength range 200–2500 nm. The effect of γ-irradiation on the optical parameters was investigated. It was observed that the increase in γ-irradiation dose caused an increase in the value of absorption index and a shift in the spectrum towards higher wavelengths. Therefore, the value of the optical band gap has decreased from 1.45 eV for as-deposited film to 1.39 eV for film exposed to γ-ray dose of 150 kGy and Urbach tail increased. On the other hand, the dispersion parameters of TCVA films were increased with the increase of the irradiation dose.     

Influence of γ-irradiation on the optical and electrical properties of Se(0.85) Te(0.15) films

Abstract

Se_(0.85) Te_(0.15) films were prepared by thermal evaporation under vacuum on glass substrate. The optical and electrical properties of as deposited and irradiated Se_(0.85) Te_(0.15) films with different γ-doses are reported.

The optical constants (absorption coefficient (α), extinction coefficient (k), refractive index (n) and dielectric constants (?, ?) of unirradiated and irradiated films were calculated. The value of allowed direct optical energy gap of Se_(0.85) Te_(0.15) films increased from 1.47 eV. to 1.72 eV. with increasing the γ-doses to 2.5 Mrad. The irradiated films have lower resistivity than those as deposited films (unirradiated). The activation energy (ΔE) increases from 0.72 eV. to 0.86 eV. with increasing γ-doses to 2.5 Mrad.     

Synthesis and magnetic properties of platelet γ-Fe2O3 particles for medical applications using hysteresis-loss heating

Platelet γ-Fe₂O₃ particles of particle size less than 100 nm were prepared for medical applications that use the hysteresis-loss heating of ferromagnetic particles. The γ-Fe₂O₃ particles were obtained through the dehydration, reduction, and oxidation of platelet α-FeOOH particles, which were synthesized by the precipitation of ferric ions in an alkaline solution containing ethanolamine, and the crystals grown using a hydrothermal treatment. The γ-Fe₂O₃ particles contained dimples formed by the dehydration of α-FeOOH particles. The coercive force and the saturation magnetization of the γ-Fe₂O₃ particles were in the ranges 11.9 to 12.7 kA/m (150 to 160 Oe), and 70 to 72 Am²/kg (70 to 72 emu/g), respectively. The specific loss power of the γ-Fe₂O₃ particles, estimated from their temperature-raising property measured under a peak magnetic field of 50.9 kA/m (640 Oe) and at a frequency of 117 kHz, was 590 W/g. This value is higher than that of spherical cobalt-containing iron oxide particles having equivalent coercive force and saturation magnetization, reflecting the larger area of the minor hysteresis loop measured under a peak magnetic field of 50.9 kA/m (640 Oe).     

Influence of oxidized interlayers on magnetic properties of multilayer films based on amorphous ferromagnet–dielectric nanocomposites

Films of composites (Co₄₅Fe₄₅Zr₁₀)_x(Al₂O₃)_100–x, (Co₈₄Nb₁₄Ta₂)_x(SiO₂)_100–x, (Co₄₁Fe₃₉B₂₀)_x(SiO₂)_100–x and multilayer heterogeneous composite–composite structures {[(Co₄₅Fe₄₅Zr₁₀)_x(Al₂O₃)_100–x]/[(Co₄₅Fe₄₅Zr₁₀)_x(Al₂O₃)_100–x + N₂]}_n, {[(Co₄₅Fe₄₅Zr₁₀)_x(Al₂O₃)_100–x]/[(Co₄₅Fe₄₅Zr₁₀)_x(Al₂O₃)_100–x + O₂]}_n, {[(Co₄₁Fe₃₉B₂₀)_x(SiO₂)_100–x]/[(Co₄₁Fe₃₉B₂₀)_x(SiO₂)_100–x + O₂]}_n, and {[(Co₈₄Nb₁₄Ta₂)_x(SiO₂)_100–x]/[(Co₈₄Nb₁₄Ta₂)_x(SiO₂)_100–x + O₂]}_n have been deposited using the ionbeam sputtering method with a cyclic supply of reaction gases during deposition. The structure and magnetic properties of the films have been studied. It has been shown that the introduction of an oxidized interlayer makes it possible to suppress the perpendicular magnetic anisotropy in the (Co₄₅Fe₄₅Zr₁₀)_x(Al₂O₃)_100–x composite with the metallic phase concentration higher than the percolation threshold.     

Effect of niobium on microstructure and magnetic properties of bulk anisotropic NdFeB/α-Fe nanocomposites

Bulk anisotropic NdFeB/α-Fe nano-composites were obtained directly from alloys of Nd₁₁Dy_0.5Fe_82.4−xNb_xB_6.1 (x=0,0.5,1.0,1.5). High resolution transmission electron microscopy images showed the existence of Nb-rich amorphous grain boundary phase in the alloys with Nb doped. Field emission scanning electron microscope morphologies and X-ray diffraction patterns revealed the grain size and grain alignment of hot pressed and hot deformed nanocomposites. It was found that Nb could refine the grain size and grain texture in hot worked ribbons. Vibrating sample magnetometer results showed that the magnetic properties of the anisotropic nanocomposites were improved with increased Nb doping. The remanence, coercivity and maximum energy product of the bulk anisotropic Nd₁₁Dy_0.5Fe_80.4Nb₂B_6.1 nanocomposites were 1.04 T, 563 kA/m and 146 kJ/m³, respectively.     

Monolithic epitaxy and optoelectronic properties of single-crystalline γ-In2Se3 thin films on mica

The growth of γ-In₂Se₃ thin films on mica by molecular beam epitaxy is studied. Single-crystalline γ-In₂Se₃ is achieved at a relatively low growth temperature. An ultrathin β-In₂Se₃ buffer layer is observed to nucleate and grow through a process of self-organization at initial deposition, which facilitates subsequent monolithic epitaxy of single-crystallineγ-In₂Se₃ at low temperature. Strong room-temperature photoluminescence and moderate optoelectronic response are observed in the achieved γ-In₂Se₃ thin films.     

Influence of ternary addition of transition elements (Cr,Si and Mn) on the microstructure and magnetic properties of nano-structured CuCo alloy

The current state of studies presents the effect of ternary addition of transition elements such as Mn, Cr and Si (10 wt%) on the mechanically driven non-equilibrium solubility of 40 wt% Co containing Cu–Co alloy. X-ray powder diffraction analysis indicates that addition of Mn has been found to be the most effective in enhancing the solubility and formation of a complete solid solution between Co and Cu in a short duration (30 h) of ball milling. The microstructure of the ball milled CuCoMn alloy was found to be stable after the isothermal annealing up to a temperature of 450 °C for 1 h. The magnetic properties such as magnetic saturation, coercivity and remanence of ball milled CuCo alloy in the presence of Mn significantly altered after annealing in the temperature range 350–650 °C for 1 h. The best combination of magnetic properties of CuCoMn alloy has been found after annealing at 550 °C for 1 h.     

Rheological properties of a γ-Fe2O3 paraffin-based ferrofluid

A stable γ-Fe₂O₃ paraffin-based ferrofluid was prepared via high energy milling. The magnetic particles were characterized using X-ray diffraction, dynamic light scattering and vibrating sample magnetometer techniques. The rheological properties of the ferrofluid were studied using a standard rotating rheometer. The magnetoviscous effect and thixotropy in the ferrofluid were studied. The formation and destruction of magnetically induced structures and the interactions of nanoparticles and aggregates are discussed.     

Influence of drying conditions on the optical and structural properties of sol–gel-derived ZnO nanocrystalline films

Zinc oxide nanothin films were prepared on glass substrate by sol–gel dip-coating method using zinc acetate dihydrate, methanol, and monoethanolamine as precursor, solvent, and stabilizer, respectively. The relationship between drying conditions and the characteristics of ZnO nanocrystalline films (c-axis orientation, grain size, roughness and optical properties) was studied. The films were dried in an oven at different temperatures and by IR radiation. Then, the films were annealed at 500°C in a furnace. The chemical composition, transmission spectra, structure, and morphology of the samples were studied using infrared (IR) and UV–visible spectroscopy, X-ray diffraction (XRD), and atomic force microscopy (AFM), respectively. The XRD results show that the drying conditions affect the orientation of crystallization along the (0 0 2) plane. AFM images show that the thicknesses of the films decrease from 128 to 93 nm by changing the drying conditions. The photoluminescence (PL) of ZnO nanothin films shows the UV emission at near band edge and broad green radiation at about 465 nm wavelength.     

Role of electrolyte pH on structural and magnetic properties of Co–Fe films

Co–Fe films were electrodeposited on polycrystalline Titanium substrates from the electrolytes with different pH levels. X-ray diffraction (XRD) was used to study the crystal structure of the films. The XRD patterns showed that the films grown at the pH levels of 3.70 and 3.30 have a mixed phase consisting of face-centred cubic (fcc) and body-centred cubic, while those grown at pH=2.90 have only fcc structure. It was observed that the film composition, by energy dispersive x-ray spectroscopy, contain around 88 at% Co and 12 at% Fe for all films investigated in this study. Morphological observations indicated that all films have grainy structure with the slight change of grain size depending on the electrolyte pH. Magnetoresistance measurements, made at room temperature, showed that all films exhibited anisotropic magnetoresistance, which is affected by the electrolyte pH. From the magnetic measurements made by vibrating sample magnetometer, the saturation magnetization increases as the electrolyte pH decreases. Furthermore, all films have in-plane easy-axis direction of magnetization.     

Influence of rhenium and ruthenium on the local mechanical properties of the γ and γ′ phases in nickel-base superalloys

The effect of rhenium and ruthenium on the hardness of the γ′ precipitates and the γ matrix in nickel-base superalloys was investigated using a nanoindenting atomic force microscope. The partitioning behaviour of the alloying elements and the lattice misfit between the γ and γ′ phase were determined in fully homogenised samples to explain the alloying effects. Rhenium strongly strengthens γ as it predominantly partitions to γ and has a strong solid solution-hardening effect. Ruthenium strengthens both γ and γ′ due to a more homogeneous partitioning behaviour. Ruthenium was found to cause less partitioning of rhenium to γ. This results in a stronger increase of the γ′ hardness. The change in the nanoindentation-derived hardness of both phases could be mainly attributed to the solid solution strengthening of Re and Ru.     

Influence of the substrate material on the properties of pulsed laser deposited thin Li1+xMn2O4−δ films

Thin Li_1+xMn₂O_4−δ films were deposited on several substrate materials (stainless steel, p-doped silicon and glassy carbon) by pulsed laser deposition. To obtain the correct thin film stoichiometries, targets with a different amount of excess lithium were required (Li_1.03Mn₂O₄ + xLi₂O; x = 2.5 and 7.5 mol%). The resulting polycrystalline thin films were characterized with respect to their morphology and electrochemical activity. It was found that only thin Li_1+xMn₂O_4−δ films deposited on stainless steel and glassy carbon showed the typical insertion and deinsertion peaks of Li⁺ during cycling.     

Effects of La–Zn substitution on microstructure and magnetic properties of strontium ferrite nanofibers

Sr_1−x La _x Zn _x Fe_12−x O₁₉/poly(vinylpyrrolidone) (PVP) (0.0≤x≤0.5) precursor nanofibers were prepared by the sol–gel assisted electrospinning method from starting reagents of metal salts and PVP. Subsequently, the Sr_1−x La _x Zn _x Fe_12−x O₁₉ nanofibers with diameters of around 100 nm were obtained by calcination of the precursor at 800 to 1000°C for 2 h. The precursor and resultant Sr_1−x La _x Zn _x Fe_12−x O₁₉ nanofibers were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectrometer and vibrating sample magnetometer. The grain sizes of Sr_0.8La_0.2Zn_0.2Fe_11.8O₁₉ nanofibers are in a nanoscale from 40 to 48 nm corresponding to the calcination temperature from 800 to 1000°C. With La–Zn substitution content increase from 0 to 0.5, the grain size and lattice constants for the Sr_1−x La _x Zn _x Fe_12−x O₁₉ nanofibers obtained at 900°C show a steady reduction trend. With variations of the ferrite particle size arising from the La–Zn substitution, the nanofiber morphology changes from the necklace-like structure linking by single elongated plate-like particles to the structure building of multi-particles on the nanofiber cross-section. The specific saturation magnetization of Sr_1−x La _x Zn _x Fe_12−x O₁₉ nanofibers initially increases with the La–Zn content, reaching a maximum value 72 A m² kg⁻¹ at x=0.2, and then decreases with a further La–Zn content increase up to x=0.5, while the coercivity exhibits a continuous reduction from 413 (x=0) to 219 kA m⁻¹ (x=0.5). The mechanism for the La–Zn substitution and the nanofiber magnetic property are analyzed.     

The influence of γ-irradiation on some physical properties of chlorophyll/PMMA films

Films of poly(methylmethacrylate) PMMA doped with different concentrations of chlorophyll, from 2.5 up to 12.5 wt.%, have been prepared by casting method. Studies were carried out utilizing FT-IR, UV/vis, fluorescence, TGA and DC electrical conduction to characterize the structural, optical and thermal properties of the films before and after irradiation. Results revealed that the structural and chemical characterizations of PMMA films are affected by the addition of chlorophyll and increasing dose of γ-irradiation. FT-IR analysis revealed that the hydroxyl and carbonyl groups were responsible for the decrease of the bands intensities with increasing the dose rate up to 100 kGy. The change in these groups was attributed to competitive processes: decomposition with ester group abstraction and oxidation with formation of new oxidized carbonyls in the polymeric chains. The values of optical energy gap for the samples were decreased upon irradiation; this indicates that there is a charge transfer complexes arise between PMMA and chlorophyll. TGA analysis shows that the addition of chlorophyll to PMMA films enhances their thermal stability. The electric conduction data were interpreted on the basis of an intrachain one-dimensional interpolaron hopping model of Kuivalainen.     

Effect of the phonon and magnetic anharmonicity on the thermal and elastic properties of nearly magnetic δ-plutonium

The temperature dependences of the total heat capacity and the lattice components of the bulk modulus, the volume thermal expansion coefficient, and the mean-square deviation of atoms from the equilibrium positions of nearly magnetic δ-plutonium (using the Pu_0.96Ga_0.04 alloy as an example) have been calculated within the framework of the self-consistent thermodynamic model. The electronic heat capacity has been calculated using the results obtained in terms of the self-consistent spin-fluctuation theory based on the inclusion of the strong magnetic anharmonicity, which leads to a splitting of the electronic spectra by fluctuating exchange fields. On this basis, the effect of phonon anharmonicity not only on the lattice heat capacity but also on other thermal and elastic properties has been considered.