Effect of a LaSrCoO3 buffer layer on Pb1 − xLaxTi1 − x/4O3 films studied by polarized Raman spectroscopy

A confocal Raman investigation of Pb_1 − xLa_xTi_1 − x/4O₃ (PLT) thin films grown by RF magnetron sputtering on PbO_x/Pt/Ti/SiO₂/Si substrates with an intermediate LaSrCoO₃ (LSCO) layer was performed. The influence of the LaSrCoO₃ buffer layer was analyzed taking advantage of the observed Raman spectral band variation, which varied according to different manufacturing procedures. In the presence of a LSCO layer, the A1(1TO) Raman mode, which was indicative of tetragonal distortion, was pronouncedly enhanced, and a slight deviation from the (0 0 1) plane of the film was observed from the angular dependence of the polarized Raman spectral intensity. Furthermore, the spectral band variation as well as the residual stress along the in-depth direction was measured in the film from cross-sectional spectral line scans. This latter measurement showed a relaxation of the lattice mismatch in the presence of LSCO and PbO layers.     

Surface anisotropy of CrxN1−x films prepared on an inner wall by magnetic sputtering

The Cr_xN_1−x films were prepared by magnetic sputtering on an inner wall of a column. Their surface morphologies were studied by atomic force microscopy (AFM) and found to be anisotropic. The 3-D AFM images indicate the grains grow upward along the rotational axis of the system. The AFM top views show a mosaic-like pattern for all samples. Analysis of the height-height correlation function demonstrates that correlation length along the rotational axis of the system is longer than that vertical to the axis. The correlation length and RMS roughness increase with the flow rate of N₂. A deposition model proposed that the shadowing effect of the reactive gas N₂ is the dominant factor for surface anisotropy. The bias added on the substrate is regarded to modulate the grain direction to the rotation axis and enhance roughness and defects.     

Spray-pyrolysis deposition of LaMnO3 and La1−xCaxMnO3 thin films

Ethylene glycol solutions of La-Mn(II) and La-Ca-Mn(II) citric complexes has been used as a starting material for spray-pyrolysis deposition of LaMnO₃ and La_1−xCa_xMnO₃ thin films on β-quartz, fused quartz, Si(0 0 1) and SrTiO₃(1 0 0) substrates heated during the deposition at 380 °C. At suitable post-deposition heating conditions highly uniform films, 0.1-1 μm in thickness, with good crystal structure were obtained. Highly textured LaMnO₃ films are obtained on SrTiO₃(1 0 0) substrate. Interaction between the layer and Si-containing substrates is observed during the post-deposition heating in static air.     

Chemical vapor deposition of ZrxTi1−xO2 and HfxTi1−xO2 thin films using the composite anhydrous nitrate precursors

Zr-Ti and Hf-Ti composite nitrates were successfully developed as single-source precursors for the chemical vapor deposition (CVD) of Zr_xTi_1−xO₂ and Hf_xTi_1−xO₂ thin films. The Zr-Ti nitrate can be assumed as a solid solution of the individual Zr and Ti nitrates, and the Zr/Ti molar ratio in the deposited Zr_xTi_1−xO₂ films is consistent with that in the precursor. The Hf-Ti nitrate appears to be a mixture of the Hf and Ti nitrates and the composition of the deposited Hf_xTi_1−xO₂ films depends remarkably on the heating time of precursor. Both Zr_xTi_1−xO₂ and Hf_xTi_1−xO₂ films exhibit trade-off properties between band gap and dielectric constant. The obtained results suggest that Zr_xTi_1−xO₂ and Hf_xTi_1−xO₂ films are promising candidates for gate dielectric application to improve the scalability and reduce the leakage current of the future complementary metal-oxide-semiconductor (CMOS) devices.     

Structural and surface properties of Si1−xGex thin films obtained by reduced pressure CVD

This paper investigates the structure and surface characteristics, and electrical properties of the polycrystalline silicon-germanium (poly-Si_1−xGe_x) alloy thin films, deposited by vertical reduced pressure CVD (RPCVD) in the temperature range between 500 and 750 °C and a total pressure of 5 or 10 Torr. The samples exhibited a very uniform good quality films formation, with smooth surface with rms roughness as low as 7 nm for all temperature range, Ge mole fraction up to 32% (at 600 °C), textures of 〈2 2 0〉 preferred orientation at lower temperatures and strong 〈1 1 1〉 at 750 °C, for both 5 and 10 Torr deposition pressures. The ³¹P⁺ and ¹¹B⁺ doped poly-Si_1−xGe_x films exhibited always lower electrical resistivity values in comparison to similar poly-Si films, regardless of the employed anneal temperature or implantat dose. The results indicated also that poly-Si_1−xGe_x films require much lower temperature and ion implant dose than poly-Si to achieve the same film resistivity. These characteristics indicate a high quality of obtained poly-Si_1−xGe_x films, suitable as a gate electrode material for submicron CMOS devices.     

Effect of Al content on the properties of Cr1−xAlxC films prepared by RF reactive magnetron sputtering

Cr_1−xAl_xC films were deposited on high-speed steel by RF reactive magnetron sputtering. In this study, we aimed to identify the effect of the Al content on the properties of Cr_1−xAl_xC films. We found that Cr_1−xAl_xC films exhibited a fine columnar grain microstructure with some special characteristics, such as high hardness of Hv 1426, a low friction coefficient of 0.29, and a large contact angle of 90° for x = 0.18. Furthermore, an increase in Al content resulted in a decrease in film hardness and an increase in contact angle. Moreover, on annealing at 923 K, the mechanical properties of the films improved and a dense protective film of complex Cr₂O₃ and Al₂O₃ oxides was formed on the surface for better wear resistance, which will ultimately increase the lifetime of the high-speed steel substrate.     

Deposition of Ag nanostructures on TiO2 thin films by RF magnetron sputtering

Ag nanostructures on TiO₂ films were deposited by RF magnetron sputtering under variable deposition parameters, such as DC potential, RF-power and total pressure. The concentration, shape, and distribution of the deposited nanostructures and continuous Ag films on thin films of TiO₂ can be tailored by careful variation of the deposition parameters. Controllable clusterlike, islandlike and film Ag structures on TiO₂ film were obtained, respectively. DC potential was found as an appropriate parameter to tailor the change of Ag nanostructure and the overall Ag amount. The compositions, nanostructures and morphologies of nanocomposite films appreciably influence the optical response.     

Preparation of five-layered Si/SixGe1−x nano-films by RF helicon magnetron sputtering

Five-layered Si/Si_xGe_1−x films on Si(1 0 0) substrate with single-layer thickness of 30 nm, 10 nm and 5 nm, respectively were prepared by RF helicon magnetron sputtering with dual targets of Si and Ge to investigate the feasibility of an industrial fabrication method on multi-stacked superlattice structure for thin-film thermoelectric applications. The fine periodic structure is confirmed in the samples except for the case of 5 nm in single-layer thickness. Fine crystalline Si_xGe_1−x layer is obtained from 700 °C in substrate temperature, while higher than 700 °C is required for Si good layer. The composition ratio (x) in Si_xGe_1−x is varied depending on the applied power to Si and Ge targets. Typical power ratio to obtain x = 0.83 was 7:3, Hall coefficient, p-type carrier concentration, sheet carrier concentration and mobility measured for the sample composed of five layers of Si (10 nm)/Si_0.82Ge_0.18 (10 nm) are 2.55 × 10⁶ /°C, 2.56 × 10¹² cm⁻³, 1.28 × 10⁷ cm⁻², and 15.8 cm⁻²/(V s), respectively.     

Temperature dependent Raman scattering in polycrystalline Bi4Ti3O12 thin films

Polycrystalline Bi₄Ti₃O₁₂ thin films were prepared on quartz substrates by pulsed laser deposition. The films were crystallized in the orthorhombic layer perovskite structure confirmed by X-ray diffraction and Raman spectroscopy. The Raman spectra are strongly dependent on temperature. A subtle phase transition in the temperature range 473-573 K exists in polycrystalline BTO thin films, which is evidenced by the disappearance of the Raman band at 116 cm⁻¹ and appearance of a new Raman band at 151 cm⁻¹. The two broad Raman bands centered at the 57 and 93 cm⁻¹ at 300 K break up into clusters of several sharp Raman peaks at 77 K, due to monoclinic distortion of orthorhombic structure at low temperature in the as-prepared Bi₄Ti₃O₁₂ thin films.     

Structural and transport properties of cubic spinel ZnCo2O4 thin films grown by reactive magnetron sputtering

We report on the growth of cubic spinel ZnCo₂O₄ thin films by reactive magnetron sputtering and bipolarity of their conduction type by tuning of oxygen partial pressure ratio in the sputtering gas mixture. Crystal structure of zinc cobalt oxide films sputtered in an oxygen partial pressure ratio of 90% was found to change from wurtzite Zn_1−xCo_xO to spinel ZnCo₂O₄ with an increase of the sputtering power ratio between the Co and Zn metal targets, D_Co/D_Zn, from 0.1 to 2.2. For a fixed D_Co/D_Zn of 2.0 yielding single-phase spinel ZnCo₂O₄ films, the conduction type was found to be dependent on the oxygen partial pressure ratio: n-type and p-type for the oxygen partial pressure ratio below ∼70% and above ∼85%, respectively. The electron and hole concentrations for the ZnCo₂O₄ films at 300 K were as high as 1.37×10²⁰ and 2.81×10²⁰ cm⁻³, respectively, with a mobility of more than 0.2 cm²/V s and a conductivity of more than 1.8 S cm⁻¹.     

Structure and electrical properties of CdIn2O4 thin films prepared by DC reactive magnetron sputtering

CdIn₂O₄ thin films were prepared by direct-current (DC) reactive magnetron sputtering. The structure, surface morphology and the chemical composition of the thin films were analyzed by X-ray diffraction (XRD), atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS), respectively. The electrical properties of the films prepared in different oxygen concentration and annealing treatment were determined, and the effects of the preparing conditions on the structure and electrical properties were also explored. It indicates that the CdIn₂O₄ thin films with uniform and dense surface morphology contain mainly CdIn₂O₄, In₂O₃ phases, and CdO phase is also observed. The XPS analysis confirms the films are in oxygen-deficient state. The electrical properties of these films significantly depend on the preparing conditions, the resistivity of the films with the oxygen concentration of 4.29% is 2.95 × 10⁻⁴ Ω cm and the Hall mobility is as high as 60.32 cm²/V s. Annealing treatment can improve the electrical performance of the films.     

c-Axis orientation control of YBa2Cu3O7−x films grown on inclined-substrate-deposited MgO-buffered metallic substrates

Biaxially textured YBa₂Cu₃O_7−x (YBCO) films were grown on non-textured metal substrates with inclined-substrate-deposited (ISD) MgO as template. The biaxial texture feature of the films was examined by X-ray pole-figure analysis, φ-scan, and 2θ-scan. A tilt angle of 32° of the MgO[001] with respect to the substrate normal was observed. Epitaxial growth of YBCO films with c-axis tilt angle of 32° with respect to the substrate normal was obtained on these substrates with SrTiO₃(STO) as buffer layer. Whereas, by choosing yttria-stabilized ZrO₂ and CeO₂ instead of STO as buffer layer, a c-axis untilted YBCO film was obtained. Higher values of T_c=91 K and J_c=5.5×10⁵ A/cm² were obtained on the c-axis untilted YBCO films with 0.46 μm thickness at 77 K in zero field. Comparative studies revealed a unique role of CeO₂ in controlling the orientation of the YBCO films grown on ISD-MgO buffered metal substrates.     

Epitaxial growth La0.67Ca0.33MnO3 thin film by radio frequency sputtering method

Perfect epitaxial growth of La_0.67Ca_0.33MnO₃ (LCMO) thin film has been achieved on (1 0 0) LaAlO₃ (LAO) single crystal substrate by radio frequency sputtering method. X-ray diffraction (XRD) and electron diffraction analysis indicates that La_0.67Ca_0.33MnO₃ film grows epitaxially on LaAlO₃ along [1 0 0] direction of the substrate. The resistivity variation with temperature of the film shows a sharp metal to semiconductor transition peak around 253 K, which is close to that of the target. The magnetoresistance (MR) also reveals high quality epitaxy film characteristic at low temperatures and near the metal to semiconductor transition temperature.     

The influence of substrate on the properties of Er2O3 films grown by magnetron sputtering

The structural properties and the room temperature luminescence of Er₂O₃ thin films deposited by RF magnetron sputtering have been studied. Films characterized by good morphological properties have been obtained by using a SiO₂ interlayer between the film and the Si substrate. The evolution of the properties of the Er₂O₃ films due to rapid thermal annealing processes in O₂ ambient performed at temperatures in the range 800-1200 °C has been investigated in details. The existence of well-defined annealing conditions (temperature of 1100 °C or higher) allowing to avoid the occurrence of extensive chemical reactions with the oxidized substrate has been demonstrated and an increase of the photoluminescence (PL) intensity by about a factor of 40 with respect to the as deposited material has been observed. The enhanced efficiency of the photon emission process has been correlated with the longer lifetime of the PL signal. The same annealing processes are less effective when Er₂O₃ is deposited on Si. In this latter case interfacial reactions and pit formation occur, leading to a material characterized by stronger non-radiative phenomena that limit the PL efficiency.     

High-throughput synthesis and characterization of Mg1−xCaxO films as a lattice and valence-matched gate dielectric for ZnO based field effect transistors

Using composition-spread technique, we have grown metastable Mg_1−xCa_xO solid solution films on ZnO layers by pulsed laser deposition. All the films exhibited (1 1 1) oriented cubic phase. Despite a large miscibility gap, no phase separation took place at growth temperatures up to 700 °C, whereas an optimal growth temperature was found at 400 °C in terms of the crystallinity. The composition-spread films were characterized by X-ray diffraction mapping technique. Both lattice parameters and diffraction intensity increased with increasing the CaO composition. The present isovalent heterointerfaces realized the perfect lattice-matching by properly adjusting the CaO composition, leading to particular interest for ZnO based field effect transistors.     

Seebeck and magnetoresistive effects of Ga-doped ZnO thin films prepared by RF magnetron sputtering

In this paper, Ga-doped ZnO (GZO) films were deposited on glass substrates at different substrate temperatures by RF magnetron sputtering. The effect of substrate temperature on the structural, surface morphological properties, Seebeck and magnetoresistive effects of GZO films was investigated. It is found that the GZO films are polycrystalline and preferentially in the [0 0 2] orientation, and the film deposited at 300 °C has an optimal crystal quality. Seebeck and magnetoresistive effects are apparently observed in GZO films. The thermoelectromotive forces are negative. Decreasing substrate temperature and annealing in N₂ flow can decrease carrier concentration. The absolute value of the Seebeck coefficient increases with decreasing carrier concentration. The maximal absolute value of Seebeck coefficient is 101.54 μV/K for the annealed samples deposited at the substrate temperature of 200 °C. The transverse magnetoresistance of GZO films is related to both the magnetic field intensity and the Hall mobility. The magnetoresistance increases almost linearly with magnetic field intensity, and the films deposited at higher substrate temperature have a stronger magnetoresistance under the same magnetic field, due to the larger Hall mobility.     

Microstructure of epitaxial SrRuO3 thin films on MgO substrates

SrRuO₃ thin films have been grown on singular (1 0 0) MgO substrates using pulsed laser deposition (PLD) in 30 Pa oxygen ambient and at a temperature of 400-700 °C. Ex situ reflection high-energy electron diffraction (RHEED) as well as X-ray diffraction (XRD) θ/2θ scan indicated that the films deposited above 650 °C were well crystallized though they had a rough surface as shown by atom force microscopy (AFM). XRD Φ scans revealed that these films were composed of all three different types of orientation domains, which was further confirmed by the RHEED patterns. The heteroepitaxial relationship between SrRuO₃ and MgO was found to be [1 1 0] SRO//[1 0 0] MgO and 45°-rotated cube-on-cube [0 0 1] SRO//[1 0 0] MgO. These domain structures and surface morphology are similar to that of ever-reported SrRuO₃ thin films deposited on the (0 0 1) LaAlO₃ substrates, and different from those deposited on (0 0 1) SrTiO₃ substrates that have an atomically flat surface and are composed of only the [1 1 0]-type domains. The reason for this difference was ascribed to the effect of lattice mismatch across the film/substrate interface. The room temperature resistivity of SrRuO₃ films fabricated at 700 °C was 300 μΩ cm. Therefore, epitaxial SrRuO₃ films on MgO substrate could serve as a promising candidate of electrode materials for the fabrication of ferroelectric or dielectric films.     

Structural and electrical properties of tantalum nitride thin films fabricated by using reactive radio-frequency magnetron sputtering

TaN thin film is an attractive interlayer as well as a diffusion barrier layer in [FeN/TaN]_n multilayers for the application as potential write-head materials in high-density magnetic recording. We synthesized two series of TaN films on glass and Si substrates by using reactive radio-frequency sputtering under 5-mtorr Ar/N₂ processing pressure with varied N₂ partial pressure, and carried out systematic characterization analyses of the films. We observed clear changes of phases in the films from metallic bcc Ta to a mixture of bcc Ta(N) and hexagonal Ta₂N, then sequentially to fcc TaN and a mixture of TaN with N-rich phases when the N₂ partial pressure increased from 0.0% to 30%. The changes were associated with changes in the grain shapes as well as in the preferred crystalline orientation of the films from bcc Ta [100] to [110], then to random and finally to fcc TaN [111], correspondingly. They were also associated with a change in film resistivity from metallic to semiconductor-like behavior in the range of 77–295 K. The films showed a typical polycrystalline textured structure with small, crystallized domains and irregular grain shapes. Clear preferred (111) stacks parallel to the substrate surface with embedded amorphous regions were observed in the film. TaN film with [111]-preferred orientation and a resistivity of 6.0 mΩ cm was obtained at 25% N₂ partial pressure, which may be suitable for the interlayer in [FeN/TaN]_n multilayers. Received: 6 December 1999 / Accepted: 24 July 2000 / Published online: 9 November 2000     

Synthesis of LECBD grown cluster assembled SeO2 thin films

Cluster assembled selenium oxide (SeO₂) thin films, as a function of oxygen flow pressure (OFP) have been synthesized by a low energy cluster beam deposition (LECBD) technique. The OFP dependent surface morphology leading to well separated nanoclusters (size ranging from 50 to 200 nm) and fractal features are confirmed from transmission electron microscopic (TEM) measurements. A diffusion limited aggregation (DLA) mediated fractal growth with dimension as 1.71 ± 0.01 has been observed for high OFP (60 mbar). Structural analysis by glancing angle X-ray diffraction (GXRD) and selected area diffraction (SAD) studies identify the presence of tetragonal phase SeO₂ in the deposit. Micro-Raman studies indicate the shifts in bending and stretching vibrational phonon modes in cluster assembled SeO₂ as compared to their bulk counter part due to the phonon confinement effect.     

Thermochromic VO2 thin films synthesized by rf-inverted cylindrical magnetron sputtering

The novel physical vapor deposition called inverted cylindrical magnetron sputtering (also known as hollow cathode sputtering) is commonly used to coat wires, fibers, ribbons as well as all sides of three-dimensional substrates. It is a reproducible method for the production of nano-structured systems onto complex shapes substrates. This paper reports the first synthesis and feasibility of reliably reproduced stoichiometric pure textured VO₂ nano-structures by the rf-inverted cylindrical magnetron sputtering. Morphological, structural, elemental analysis and optical properties of synthesized VO₂ under optimized conditions are reported.