Optimization of direct arylation polymerization conditions for the synthesis of poly(3‐hexylthiophene)

Direct arylation polymerization (DArP) is an emerging alternative to Stille and Suzuki polymerizations. This method is attractive as it allows preparation of high‐molecular‐weight conjugated polymers in good yield without the need to metallate monomers. Despite this promise, for poly(3‐hexylthiophene) (P3HT) and related polymers that have β‐protons on the thiophene ring, DArP is known to produce β‐defects, which make the polymer properties different from polymers produced by traditional methods. Here, we demonstrate that DArP conditions based on simple, inexpensive, and bench‐stable reagents can be tuned to limit the amount of defects and produce P3HT with properties remarkably similar to Stille P3HT. Specifically, lowering the reaction temperature, lowering the amount of catalyst, and using a bulkier carboxylate ligand is critical. Optimized conditions include reacting 2‐bromo‐3‐hexylthiophene with 0.25 mol % of Pd(OAc)₂, 1.5 equivalents of K₂CO₃, and 0.3 equivalents of neodecanoic acid in N,N‐dimethylacetamide at 70 °C and give DArP P3HT with ～60% yield, regioregularity of 93.5%, molecular weight of 20 kDa, polydispersity of 2.8, and melting point of 217 °C, providing a very close match to Stille P3HT, which is obtained with 70–80% yield, 91–94% regioregularity, molecular weight of 15–25 kDa, polydispersity of 2.5–2.8, and melting point of 214–221 °C. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2660–2668     

The effect of amide solvent structure on the direct arylation polymerization (DArP) of 2‐Bromo‐3‐hexylthiophene

In this work, we investigate the influence of the amide solvent chemical structure on the properties of poly(3‐hexylthiophene) (P3HT) prepared via direct arylation polymerization (DArP). Our findings indicate that for successful polymerization the amide must possess an acyclic aliphatic structure since cyclization of an amide results in a complete shutdown of DArP reactivity as evidenced by failed polymerization in N‐methylpyrrolidone, whereas the presence of an aromatic motif renders the amide solvent susceptible to C? H activation and leads to incorporation of the solvent structure into the P3HT backbone, as demonstrated on the example of N,N‐diethylbenzamide. Additionally, we observed that the steric bulk of alkyl substituents on both the nitrogen atom and the carbonyl group within the amide structure has to be delicately balanced for optimal DArP reactivity. In the optimal cases, P3HT is obtained in high yield, with high molecular weight and contains a minimal amount of structural defects. The obtained polymer samples were comprehensively studied in terms of their chemical structure, optical, thermal and solid‐state properties in thin films using GPC analysis, ¹H NMR, MALDI, UV–vis, GIXRD spectroscopy, and DSC. We additionally note a drastic difference of the amide solvent effect between DArP and Stille polymerization. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2494–2500     

Analysis of diverse direct arylation polymerization (DArP) conditions toward the efficient synthesis of polymers converging with stille polymers in organic solar cells

Despite the emergence of direct arylation polymerization (DArP) as an alternative method to traditional cross‐coupling routes like Stille polymerization, the exploration of DArP polymers in practical applications like polymer solar cells (PSCs) is limited. DArP polymers tend to have a reputation for being marginally inferior to Stille counterparts due to the increased presence of defects that result from unwanted side reactions in direct arylation, such as unselective C‐H bond activation and homocoupling. We report ten DArP protocols across the three major classes of DArP to generate poly[(2,5‐bis(2‐hexyldecyloxy)phenylene)‐alt‐(4,7‐di(thiophen‐2‐yl)benzo[c][1,2,5]thiadiazole)] (PPDTBT). Through evaluation of the method and resulting photophysical and electronic properties, we show not all DArP methods are suitable for generating device‐quality alternating copolymers. When DArP PPDTBT was synthesized in superheated THF with Cs₂CO₃, neodecanoic acid, and P(o‐anisyl)₃, it generated polymers of exceptional quality that performed comparably to Stille counterparts in both roll coated ITO‐free and spin‐coated ITO devices. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2907–2918     

Minimization of the auxiliary reagent loading for direct arylation polymerization (DArP) of 2‐bromo‐3‐hexylthiophene

In this work, we present a powerful set of synthetic strategies aimed at minimization of auxiliary reagent loading for direct arylation polymerization (DArP) of 2‐bromo‐3‐hexylthiophene. As such, we report efficient lowering of Pd(OAc)₂ catalyst loading as well as loading of other auxiliary reagents, such as neodecanoic acid and N,N‐dimethylacetamide. Unprecedented low loadings of catalyst down to 0.0313% (313 ppm) were achieved, while producing polymer in high yield (91% after Soxhlet extraction), with a high molecular weight (24.2 kDa) and carefully controlled chemical structure thus making the optimized DArP protocol significantly more cost‐effective, convenient, sustainable, and environmentally friendly. The resulting polymer samples were thoroughly investigated in terms of their chemical structure as well as optical, thermal, chain ordering and electronic properties using GPC analysis, ¹H NMR, MALDI, UV–vis, GIXRD spectroscopy, DSC, and SCLC hole mobility measurements. The results demonstrate that the reagent lowering strategies increase the polymer regioregularity from 94.6 to 96.5% as evidenced by ¹H NMR spectra and corroborated by GIXRD, DSC, and UV–vis measurements. Additionally, polymer samples obtained at low reagent loading are more uniformly proton‐terminated as evidenced by ¹H NMR and MALDI end‐group analysis. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1492–1499     

One‐step synthesis of ladder‐type fused poly(benzopentalene) derivatives with tunable energy levels by variable substituents

Novel ladder‐type conjugated polymers, fused poly (benzopentalene) derivatives, were synthesized from the readily accessible 1,4‐dibromo‐2,5‐diethynylbenzene derivatives by the Pd‐catalyzed self‐polycondensation in one‐step with high yields. The low solubility of the ladder structure was suggested when the triisopropylsilyl substituents were selected. However, when longer alkyl chains were introduced into the peripheral moieties, such as the dialkylanilino (DAA) and alkyloxyphenyl groups, a high solubility was achieved and the number‐average molecular weight (M_n) reached 18,000. The UV‐Vis absorption spectral shapes of the polymers were similar to the reported dibenzopentalene derivatives, except for the bathochromically shifted end absorptions. This result suggests an extension of the π‐conjugated systems due to the polymerization. Moreover, the almost defect‐free structure of the ladder‐type polymers was confirmed by the quantitative tetracyanoethylene (TCNE) addition to the DAA‐activated alkynes. The titration experiments of TCNE to the polymers revealed the number of terminal alkynes, which enabled us to calculate the molecular weight of the polymers. The calculated molecular weight was consistent with that determined by GPC. After the TCNE addition, the polymer band gaps reasonably decreased as suggested by the UV‐Vis‐NIR absorption and electrochemical measurements. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Improving the efficiency and sustainability of catalysts for direct arylation polymerization (DArP)

In the past decade, direct arylation polymerization (DArP) has rapidly developed as a sustainable synthetic protocol for cost-effective, atom-economical preparation of conjugated polymers. By circumventing monomer functionalization with toxic transmetallating reagents such as organostannane and organoboron required for Stille-Migita and Suzuki-Miyaura polymerization methods, DArP proceeds through a metal-catalyzed C H activation pathway for the preparation of high-performance conjugated polymer materials. This review evaluates the development of several classes of efficient catalysts/catalytic systems from small-molecule studies to polymerizations, including the mechanisms involved in these transformations and how they inspire catalyst and monomer design for defect-free conjugated polymer synthesis. Recent advances in developing more sustainable first-row transition metal catalysts for DArP are also highlighted, and the fundamental understanding of these efficient and sustainable catalysts should motivate the pursuit for the next generation of catalytic design to enable more effective and environmentally friendly conjugated polymer synthesis.     

Radical polymerization behavior and molecular weight development of homologous monoacrylate monomers in lyotropic liquid crystal phases

Polymerization in highly ordered lyotropic liquid‐crystalline (LLC) media enables controllable synthesis of polymers possessing interesting nanostructure and physical properties. This study investigates the radical polymerization rate and molecular weight (MW) development of monoacrylates of different aliphatic tail length in a range of LLC phases. Polymerization rate data were acquired using photodifferential scanning calorimetry, and linear polymer MW was determined with gel permeation chromatography. Polymerization occurs much more rapidly, and higher MW is attained in the ordered LLC phases relative to isotropic solutions and neat polymerization. These properties change significantly as a function of LLC phase and monomer structure. A direct relationship is observed between polymer MW formation and the polymerization rate. Definitive changes in rate and MW were observed at phase boundaries, indicating the important role of solvent order. This study demonstrates how solvent ordering effects can be used to control polymer MW and rate of polymerization. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 144–154     

Direct arylation polymerization toward ultra‐low bandgap poly(thienoisoindigo‐alt‐diketopyrrolepyrrole) conjugated polymers: The effect of β‐protection on the polymerization and properties of the polymers

Direct arylation polymerization between derivatives of dibromodiketopyrrolopyrrole (DPP) and thienoisoindigo (TIIG) resulted in two π‐conjugated copolymers with average molecular weights up to 24.0 kDa and bandgaps as low as 0.8 eV. The structural analysis of the obtained two polymers revealed well‐defined alternating conjugation backbones without obvious structural defects. The introduction of hexyl‐group in the β‐position of thiophene rings in the DPP units not only reduces the bandgap of conjugated polymer compared to a similar polymer containing bare‐thiophene flanked DPP but also affects polymer morphology in thin films. P‐type charge‐transport characteristics were observed for two polymers in organic field‐effect transistors with comparable hole mobilities. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3205–3213     

Synthesis of D‐π‐A‐π type benzodithiophene‐quinoxaline copolymers by direct arylation and their application in organic solar cells

Conjugated copolymers based on benzodithiophene (BDT) derivatives and thiophene‐quinoxaline‐thiophene (TQT) segments represent an efficient class of light harvesting materials for organic photovoltaic (OPV) applications. Commonly, BDT‐TQT copolymers are synthesized by Stille cross‐coupling polymerization. In this study, alkoxy and thienyl functionalized alternating BDT‐alt‐TQT copolymers are synthesized by direct arylation polymerization (DArP), using Ozawa conditions. An extensive optimization of the reaction conditions such as the catalytic system, solvent, temperature, base, and the concentration of the catalyst is accomplished. The optical and electrochemical properties of the copolymers obtained by DArP are compared to the reference polymers synthesized by Stille cross‐coupling polymerization. Finally, the optimized BDT‐alt‐TQT copolymers are incorporated into organic solar cells as electron donors. The solar cells of the DArP copolymers exhibit power conversion efficiencies up to 80% (rel.) of their Stille cross coupling analogues. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1457–1467     

Synthesis of Thieno[3,4-b]pyrazine-based Alternating Conjugated Polymers via Direct Arylation for Near-infrared OLED Applications

Three alternating conjugated polymers,namely PFTP,PCz TP,and PSi TP,which combine a thieno[3,4-b]pyrazine(TP)unit with different benzene-based donor units such as 9,9-dioctylfluorene,9-heptadecyl-9H-carbazole and 5,5-dioctyl-5H-dibenzo[b,d]silole,were synthesized in good yield(>85%)and high molecular weight up to Mn=5.82×10⁴ via direct arylation polymerization(DAr P).All the resultant polymers exhibit moderate bandgap of about 1.80 e V and strong deep red/near-infrared emitting in the solid state.Among them,the PSi TP-based electroluminescence(EL)devices with an architecture of ITO/PEDOT:PSS/PTAA/emitting layer/TPBi/Li F/Al give the best performance with a maximum luminance of 2543 cd/m² at 478 m A/cm².This work expands the application scope of high-performance conjugated polymers which can be synthesized by DAr P.     

The effect of molecular weight on the separation of semiconducting single‐walled carbon nanotubes using poly(2,7‐carbazole)s

The use of selective interactions between conjugated polymers and single‐walled carbon nanotubes has emerged as a promising method for the separation of nanotubes by electronic type. Although much attention has been devoted to investigating polyfluorenes and their ability to disperse semiconducting carbon nanotubes under specific conditions, other polymer families, such as poly(2,7‐carbazole)s, have been relatively overlooked. Poly(2,7‐carbazole)s have been shown to also preferentially interact with semiconducting carbon nanotubes, however a detailed investigation of polymer parameters, such as molecular weight, has not been performed. We have prepared seven different molecular weights of a poly(2,7‐carbazole), from short chain oligomers to high molecular weight polymers, and have investigated their effectiveness at dispersing semiconducting single‐walled carbon nanotubes. Although all polymer chain lengths were able to efficiently exfoliate carbon nanotube bundles using a mild dispersion protocol, only polymers above a certain threshold molecular weight (M_n ～ 27 kDa) were found to exhibit complete selectivity for semiconducting nanotubes, with no observable signals from metallic species. Additionally, we found the quality of separation to be strongly dependent on the ratio of polymer to carbon nanotube. Contrary to previous reports, we have found that an excess of poly(2,7‐carbazole) leads to incomplete removal of metallic carbon nanotubes. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2510–2516     

Hyperbranched Polyfluorinated benzyl ether polymers: Mechanism,kinetics, and optimization

Highly fluorinated, hyperbranched polymers were synthesized from the polycondensation of AB₂ monomers, 3,5‐bis[(pentafluorobenzyl)oxy]benzyl alcohol and 3,5‐bis[(pentafluorobenzyl)‐oxy]phenol with potassium carbonate base, and 18‐crown‐6 phase transfer agent in a variety of polar aprotic solvents. The regioselectivity of the polymerization was optimized and was found to be temperature dependent. The new polymerization technique produced higher molecular weight polymer using safer conditions than earlier methods. The resulting optimization was used to control substitution of oxygen‐bearing nucleophiles along nonactivated fluoroaryl systems in high yield. Water was found to induce side reactions that generate a highly conjugated fluoroaryl phenol with lowered reactivity. The removal of a methylene spacer in the polymer backbone of the hyperbranched polymer produced a polymer with greater thermal stability. The reaction conditions for polymerization were found to be general for nucleophile‐bearing perfluorinated systems. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 985–994     

共轭聚合物的结构缺陷及对光电性能的影响

共轭聚合物是由大量重复基元通过化学键连接的一维体系,具有独特的光、电、电化学等性质,已经引起学术界的广泛关注.由于共轭聚合物结构(链段、构象、聚集态)的复杂性,即使在非常精细的合成条件下,少量结构缺陷的形成也是难免的.共轭聚合物,特别在其固态状态下激发能量能够有效传递,使得少量缺陷的影响被放大,对其光电性质产生巨大影响.因此对共轭聚合物结构缺陷的研究,包括缺陷成因与控制、缺陷密度的分析、缺陷的分子结构与电子结构特征等,对于高品质材料的研发具有重要的意义.本文对国内外研究进展进行了比较详尽的介绍.     

Reactive ligand influence on initiation in phenylene catalyst‐transfer polymerization

Synthesizing conjugated polymers via catalyst‐transfer polymerization (CTP) has led to unprecedented control over polymer sequence and molecular weight. Yet many challenges remain, including broadening the monomer scope and narrowing the molecular weight dispersities. Broad polymer dispersities can arise from nonliving pathways as well as slow initiation. Previously, slow initiation was observed in Ni‐mediated CTP of phenylene monomers. Although precatalysts with faster initiation rates have been reported, the rates still do not exceed propagation. Herein a second‐ and third‐generation of reactive ligands are described, along with a simple method for measuring initiation rates. A precatalyst with an initiation rate that exceeds propagation is now reported, however, the resulting polymer samples still exhibit broad dispersities, suggesting that slow initiation is not the most significant contributing factor in Ni‐mediated phenylene polymerizations. In addition, initiation rates measured under authentic polymerization conditions revealed that both exogenous triphenylphosphine and an ortho‐trifluoroethoxy substituent on the reactive ligand have a strong influence. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1530–1535     

Reversible addition‐fragmentation chain transfer polymerization of diisopropyl fumarate using various dithiobenzoates as chain transfer agents

Dialkyl fumarates as 1,2‐disubstituted ethylenes exhibit unique features of radical polymerization kinetics due to their significant steric hindrance in propagation and termination processes and provide polymers with a rigid chain structure different from conventional vinyl polymers. In this study, we carried out reversible addition‐fragmentation chain transfer polymerization of diisopropyl fumarate (DiPF) in bulk at 80 °C using various dithiobenzoates with different leaving R groups as chain transfer agents to reveal their performance for control of molecular weight, molecular weight distribution, and chain end functionality of the resulting poly(DiPF) (PDiPF). 2‐(Ethoxycarbonyl)‐2‐propyl dithiobenzoate ( DB1 ) and 2,4,4‐trimethyl‐2‐pentyl dithiobenzoate ( DB2 ) underwent fragmentation and reinitiation at a moderate rate and consequently led to the formation of PDiPF with well‐controlled chain structures. It was confirmed that molecular weight of PDiPF produced by controlled polymerization with DB1 and DB2 agreed with theoretical one and molecular weight distribution was narrow. Dithiobenzoate and R fragments were introduced into the polymer chain ends with high functionality as 95% by the use of DB1 . In contrast, polymerizations using 1‐(ethoxycarbonyl)benzyl dithiobenzoate ( DB3 ), 1‐phenylethyl dithiobenzoate ( DB4 ), and 2‐phenyl‐2‐propyl dithiobenzoate ( DB5 ) resulted in poor control of molecular weight, molecular weight distribution, and chain end structures of PDiPF. Fragmentation and reinitiation rates of the used benzoates as chain transfer agents significantly varied depending on the R structures in an opposite fashion; that is, introduction of bulky and conjugating substituents accelerated fragmentation, but it retarded initiation of DiPF polymerization. It was revealed that balance of fragmentation and reinitiation was important for controlled polymerization of DiPF. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3266–3275     

Synthesis,properties and molecular modeling of functional hyperbranched polymers and dendrimers

The design, synthesis, properties and molecular modeling of fully conjugated dendritic molecules and conjugated hyperbranched polymers are described. It has been shown that conjugated hyperbranched molecules are much more soluble than their linear analogues while maintaining all the properties characteristic of conjugated polymers. It was found that the use of polymeric solid support in hyperbranched polymerization allows to control molecular weight and degree of branching (DB). The molecular modeling of hyperbranched conjugated molecules reveals that hyperbranched structure of conjugated molecules affects significantly neither their stability nor the conjugation. On the other hand the terminal groups affect appreciably the electronic structure of conjugated hyperbranched molecules.     

A bicyclic conjugated diene monomer,tetrahydroindene, for cationic polymerization and a novel alicyclic hydrocarbon polymer with heat resistance

This study was directed toward the cationic polymerization of tetrahydroindene (i.e., bicyclo[4.3.0]‐2,9‐nonadiene), a bicyclic conjugated diene monomer, with a series of Lewis acids, especially focusing on the synthesis of high‐molecular‐weight polymers and subsequent hydrogenation for novel cycloolefin polymers with high service temperatures. EtAlCl₂ or SnCl₄ induced an efficient and quantitative cationic polymerization of tetrahydroindene to afford polymers with relatively high molecular weights (number‐average molecular weight > 20,000) and 1,4‐enchainment bicyclic main‐chain structures. The subsequent hydrogenation of the obtained poly(tetrahydroindene) with p‐toluenesulfonyl hydrazide resulted in a saturated alicyclic hydrocarbon polymer with a relatively high glass transition (glass‐transition temperature = 220 °C) and improved pyrolysis temperature (10% weight loss at 480 °C). The new diene monomer was randomly copolymerized with cyclopentadiene at various feed ratios in the presence of EtAlCl₂ to give novel cycloolefin copolymers, which were subsequently hydrogenated into alicyclic copolymers with variable glass‐transition temperatures (70–220 °C). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6214–6225, 2006     

Topochemical Polymerization of 1,3‐Diene Monomers and Features of Polymer Crystals as Organic Intercalation Materials

From the viewpoint of controlled polymer synthesis, topochemical polymerization based on crystal engineering is very useful for controlling not only the primary chain structures but also the higher‐order structures of the crystalline polymers. We found a new type of topochemical polymerization of muconic and sorbic acid derivatives to give stereoregular and high‐molecular weight polymers under photo‐, X‐ray, and γ‐ray irradiation of the monomer crystals. In this article, we describe detailed features and the mechanism of the topochemical polymerization of diethyl‐(Z,Z)‐muconate as well as of various alkylammonium derivatives of muconic and sorbic acids, which are 1,3‐diene mono‐ and dicarboxylic acid derivatives, to control the stereochemical structures of the polymers. The polymerization reactivity of these monomers in the crystalline state and the stereochemical structure of the polymers produced are discussed based on the concept of crystal engineering, which is a useful method to design and control the reactivity, structure, and properties of organic solids. The reactivity of the topochemical polymerization is determined by the monomer crystal structure, i.e. the monomer molecular arrangement in the crystals. Polymer crystals derived from topochemical polymerization have a high potential as new organic crystalline materials for various applications. Organic intercalation using the polymer crystals prepared from alkylammonium muconates and sorbates is also described.     

Stereospecific and molecular weight‐controlled polymerization of 1,3‐butadiene with Co(acac)3‐MAO catalyst

The polymerization of butadiene (Bd) with Co(acac)₃ in combination with methylaluminoxane (MAO) was investigated. The polymerization of Bd with Co(acac)₃‐MAO catalysts proceeded to give cis‐1,4 polymers (94 – 97%) bearing high molecular weights (40 × 10⁴) with relatively narrow molecular weight distributions (M_w's/M_n's). The molecular weight of the polymers increased linearly with the polymer yield, and the line passed through an original point. The polydispersities of the polymers kept almost constant during reaction time. This indicates that the microstructure and molecular weight of the polymers can be controlled in the polymerization of Bd with the Co(acac)₃‐MAO catalyst. The effects of reaction temperature, Bd concentration, and the MAO/Co molar ratio on the cis‐1,4 microstructure and high molecular weight polymer in the polymerization of Bd with Co(acac)₃‐MAO catalyst were observed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2793–2798, 2001     

Polymerization of β‐pinene with Schiff‐base nickel complexes catalyst: Synthesis of relatively high molecular weight poly(β‐pinene) at high temperature with high productivity

A series of easily accessible and stable Schiff‐base nickel complexes (complex 1 – 4 ) in conjunction with methylaluminoxane (MAO) were employed for the synthesis of relatively high molecular weight β‐pinene polymers at high temperature with high productivity. The ligand structure of the complex had a substantial effect on the polymerization in terms of the productivity and the molecular weight. With complex 4 in the presence of MAO, high molecular weight polymers of β‐pinene (M_n ～ 10,900) were obtained at 40 °C with an extremely high productivity up to 1.25 × 10⁷ g polyβ‐pinene/mol of Ni. ¹H NMR analyses showed that the obtained β‐pinene polymer was structurally identical to that formed by conventional cationic Lewis acid initiators. The polymerization was presumably initiated by the nickel cation formed by the reaction of the schiff‐base nickel complex and MAO, while the propagation proceeded in a manner typical for a conventional carbocationic polymerization process. Direct evidence for the carbocationic polymerization was offered by the fact that quenching of the polymerization with methanol at a low monomer conversion resulted in incorporation of a methoxyl end group into the polymer chain. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3739–3746, 2007