Development of an analytical method for the determination of the residues of four pyrethroids in meat by GC–ECD and confirmation by GC–MS

The development of an analytical method for the determination of four selected pyrethroid insecticides at residue level in beef meat is presented. Acetone and petroleum ether at 40-60 degrees C were chosen as extraction solvents. A two-step clean-up was performed using an Extrelut NT3-C(18) system followed by a Florisil column, with disposable, ready-to-use cartridges. Instrumental analysis was carried out on a gas chromatograph equipped with an electron capture detector (GC-ECD), using matrix-matched and internal standard calibration techniques. Confirmatory analysis by GC-MS was performed. Recoveries at the EU Maximum Residue Limit (MRL), 0.5 x MRL and 1.5 x MRL levels and the repeatabilities were widely satisfactory. The main advantage of the method was the reduction of analysis time as compared with previously published works. The applicability of the method to different matrices and pesticide classes will be investigated.     

A novel method of liquid chromatography–tandem mass spectrometry combined with chemical derivatization for the determination of ribonucleosides in urine

Ribonucleosides are the end products of RNA metabolism. These metabolites, especially the modified ribonucleosides, have been extensively evaluated as cancer-related biomarkers. However, the determination of urinary ribonucleosides is still a challenge due to their low abundance, high polarity and serious matrix interferences in urine samples. In this study, a derivatization method based on a chemical reaction between ribonucleosides and acetone to form acetonides was developed for the determination of urinary ribonucleosides. The derivative products, acetonides, were detected by using liquid chromatography–tandem mass spectrometry (LC–MS/MS). The methodological evaluation was performed by quantifying four nucleosides for linear range, average recovery, precision, accuracy and stability. The validated procedures were applied to screen modified ribonucleosides in urine samples. Improvement of separation and enhancement of sensitivity were obtained in the analysis. To identify ribonucleosides, inexpensive isotope labeling acetone (acetone-d₆) and label-free acetone were applied to form ordinary and deuterated acetonides, respectively. The two groups of samples were separated with orthogonal partial least squares (OPLS). The ordinary and deuterated pairs of acetonides were symmetrically distributed in the S-plot for easy and visual signal identification. After structural confirmation, a total of 56 ribonucleosides were detected, 52 of which were modified ribonucleosides. The application of derivatization, deuterium-labeling and multivariate statistical analysis offers a new option for selective detection of ribonucleosides in biological samples.     

GC×GC-ECD: a promising method for the determination of dioxins and dioxin-like PCBs in food and feed

There is a need for cost-efficient alternatives to gas chromatography (GC)–high-resolution mass spectrometry (HRMS) for the analysis of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (PCBs) in food and feed. Comprehensive two-dimensional GC–micro electron capture detection (GC×GC-μECD) was tested and all relevant (according to the World Health Organisation, WHO) PCDD/Fs and PCBs could be separated when using a DB-XLB/LC-50 column combination. Validation tests by two laboratories showed that detectability, repeatability, reproducibility and accuracy of GC×GC-μECD are all statistically consistent with GC-HRMS results. A limit of detection of 0.5 pg WHO PCDD/F tetrachlorodibenzo-p-dioxin equivalency concentration per gram of fish oil was established. The reproducibility was less than 10%, which is below the recommended EU value for reference methods (less than 15%). Injections of vegetable oil extracts spiked with PCBs, polychlorinated naphthalenes and diphenyl ethers at concentrations of 200 ng/g showed no significant impact on the dioxin results, confirming in that way the robustness of the method. The use of GC×GC-μECD as a routine method for food and feed analysis is therefore recommended. However, the data evaluation of low dioxin concentrations is still laborious owing to the need for manual integration. This makes the overall analysis costs higher than those of GC-HRMS. Further developments of software are needed (and expected) to reduce the data evaluation time. Combination of the current method with pressurised liquid extraction with in-cell cleanup will result in further reduction of analysis costs. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Headspace single-drop microextraction and GC–ECD determination of chlorpyrifos-ethyl in rat liver

The present work describes a headspace single-drop microextraction (HS-SDME) method in conjunction with gas chromatography electron capture detection (GC–ECD) for the determination of an organophosphate insecticide, chlorpyrifos-ethyl (CPF), in rat liver. Sample preparation included tissue homogenization with methanol in the presence of anhydrous sodium sulfate in order to isolate CPF from the matrix, followed by dilution with 10 mL of 0.1 M H₂SO₄ and headspace microextraction to a 2-μL drop of 1-octanol. The main factors affecting extraction efficiency were optimized [temperature 90 °C, preheating and extraction times of eight and six minutes, respectively, 2 g of (NH₄)₂SO₄, stirring rate of 1000 rpm, 200 μL of methanolic extract]. The method allows for the separation and quantitation of residue levels of CPF in the livers of rats exposed orally to that insecticide. Using internal standardization (with chlorpyrifos-methyl used as an internal standard), the linearity of the method was demonstrated in the range 10–2500 ng g⁻¹ with a correlation coefficient R > 0.996 and a satisfactory level of precision (RSD 3.85%, n = 6). Moreover, the results obtained with the new method do not differ from those obtained with the conventional residue method used in our laboratory. The feasibility of this HS-SDME approach as an equivalent analytical method for the determination of CPF in rat liver that possessess advantages such as low cost, low solvent consumption and high throughput was confirmed. Figure Headspace single-drop microextraction     

Application of a simple and sensitive GC–MS method for determination of morphine in the hair of opium abusers

Thirty hair samples were collected from male opioid abusers for whom the presence of morphine in their urine samples was confirmed by thin layer chromatography (TLC). The hair samples were decontaminated by washing with isopropanol, deionized water, and isopropanol, dried at room temperature, and cut into small pieces. Samples of the latter (30 mg ) were digested by incubation in a mixture of methanol–trifluoroacetic acid (9:1) for 18 h at 45 °C and sonicated to improve the extraction process. The methanolic phase was evaporated to dryness under a stream of nitrogen at 50 °C. The sample was derivatized by addition of N-methyl-N-trimethylsilyltrifluoroacetamide (MSTFA) and 1% trimethyliodosilane (TMIS) at 70 °C for 20 min, with sonication. Derivatized samples (1 L) were injected into a gas chromatograph–mass spectrometer (GC–MS) system fitted with a capillary column; the Finnigan MS was operated in SIM mode. Naltrexone was used as internal standard (IS). The masses of the ions selected for morphine and naltrexone were 429 and 557, respectively. The limit of quantitation was set at 0.03 ng mg^–1 hair. By using the above procedure we detected morphine in all the samples examined, in the concentration range 0.26–10.31 ng mg^–1 hair.     

Validation and application of a novel UHPLC–MS/MS method for the measurement of furanodienone in rat plasma

A sensitive ultra-high performance liquid chromatography–tandem mass spectrometry (UHPLC–MS/MS) method was established to analyze furanodienone in rat plasma. In the process of chromatographic separation, selected reaction monitoring transitions for furanodienone and patchouli alcohol (internal standard, IS) were m/z 231.1 → 83.2 and m/z 205.1 → 95.1, respectively. Great linearity of furanodienone in plasma samples was found in the corresponding concentration range (r > 0.995). Intra- and inter-day precisions (RSD, %) were <11.3% in plasma, and the accuracy (RE, %) was within ±10.7%. This method was used to the furanodienone study on rat pharmacokinetics after a single oral dose of 10 mg/kg of furanodiene. The results indicated that the maximum observed plasma concentration was 52.4 ± 19.1 ng/ml at 1.2 ± 0.7 h with an elimination half-life of 2.2 ± 0.7 h. The obtained data indicated that furanodienone could be moderately distributed and eliminated.     

GC–MS method for the determination of paraben preservatives in the human breast cancerous tissue

The general presumption that the preservative laden personal care products may be one of the causative agents for breast cancer, has remained a matter of controversy during this decade. Extensive studies have not been carried out to either prove or disprove the role of preservatives in breast cancer incidences. In this study we have developed a new method for the identification and quantification of the preservatives such as methyl paraben (MeP), ethyl paraben (EtP), propyl paraben (PrP) and butyl paraben (BuP) in breast tissue using Gas Chromatography and Mass Spectrometry (GC–MS). Tissue was extracted by using acetone:n-hexane mixture (1:1 v/v) and derivatized with N-Methyl-N-(trimethylsilyl) trifluoroacetamide (MSTFA). The extent of reaction time and the amount of MSTFA to attain greater derivatization were optimized. The developed method yielded good recovery (mean ± SD) of 99.8 ± 5.1, 96 ± 4.4, 107 ± 17 and 113 ± 13% with relative standard deviations (RSDs) of 5.1, 4.6, 15.6 and 13%, and the limits of detection (LOD) of 2.02, 1.05, 1.71 and 3.75 ng g^− 1 for MeP, EtP, PrP and BuP, respectively. The method was successfully validated for the determination of parabens including butyl paraben (log K_ow = 3.57) in cancerous breast tissues; this could be a promising one for screening of breast tissues and also the environment for paraben residues. As far as our knowledge goes this is the first GC–MS method for the determination of parabens in human tissue.     

Development of a multianalyte method for the determination of anabolic hormones in bovine urine by isotope-dilution GC–MS/MS

A sensitive, specific and selective multianalyte GC–MS/MS method has been developed for the determination of 11 anabolic hormones in bovine urine. After adjusting the urine pH to 4.8, the samples were spiked with deuterated internal standards and submitted to enzymatic hydrolysis with β-glucuronidase/arylsulfatase. Hormones were eluted with methanol through a C18 solid phase cartridge and submitted to a liquid–liquid extraction. Analytes were derivatized by adding N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) with 1% trimethylchlorosilane and GC–MS data were obtained in the positive electron impact tandem mass mode. Under these conditions, no matrix effects were observed and limit of detection values were in the range of 0.005 ng/mL (diethylstilbestrol) to 0.38 ng/mL (17α-methyltestosterone and 17α-ethynylestradiol). Recoveries from 81% (α-zeranol) to 149% (17α-methyltestosterone) were found under the selected conditions. These results were better than those found using heptafluorobutyric anhydride (HFBA) as derivative reagent and those measured in full scan and selective ion monitoring modes.     

A rapid and sensitive GC–MS method for determination of 1,3-dichloro-2-propanol in water

A rapid analytical method for sensitive determination of 1,3-dichloro-2-propanol (1,3-DCP) in river water has been developed. 1,3-DCP is extracted from water with ethyl acetate. After filtration through sodium sulfate the ethyl acetate phase is analyzed by gas chromatography–mass spectrometry. The method uses 1,3-DCP-d₅ as internal standard. Different extraction solvents, concentrations of ammonium sulfate in the water samples, and the effect of humic acid were tested and their influence on the recovery of DCP has been evaluated. The method quantification limit was 0.1 g L^–1. For spiked water samples (0–5.2 g L^–1, n=21) a repeatability coefficient of variation of 5.4% was obtained. The average recovery rate of 1,3-DCP was 105±3% (n=21). Stability tests, which were carried out with Danube river water, led to an estimated 1,3-DCP degradation rate of 0.008±0.0008 day^–1 at 6°C.     

New Procedure for the Determination of 3-Nitrotyrosine in Plasma by GC–ECD

A method suitable for the determination of 3-nitrotyrosine, a well known marker of nitro-oxidative stress, in plasma by GC–ECD has been investigated. After deproteinisation, SPE and LC separation, 3-nitrotyrosine was derivatised by a single-step procedure to the corresponding N-heptafluorobutyryl heptafluorobutyl ester and analysed. The precision and reliability of the procedure were assured by using 4-nitrophenylalanine as internal standard and a diverter valve to protect the detector. The method was applied to the analysis of volunteers’ plasma samples.     

Validated HPLC–MS–MS method for determination of azithromycin in human plasma

A validated, highly sensitive, and selective HPLC method with MS–MS detection has been developed for quantitative determination of azithromycin (AZI) in human Na₂EDTA plasma. Roxithromycin (ROX) was used as internal standard. Human plasma containing AZI and internal standard was ultrafiltered through Centrifree Micropartition devices and the concentration of AZI was determined by isocratic HPLC–MS–MS. Multiple reaction monitoring mode (MRM) was used for MS–MS detection. The calibration plot was linear in the concentration range 2.55–551.43 ng mL⁻¹. Inter-day and Intra-day precision and accuracy of the proposed method were characterized by R.S.D and percentage deviation, respectively; both were less than 8%. Limit of quantification was 2.55 ng mL⁻¹. The proposed method was used to determine the pharmacokinetic profile of AZI (250-mg tablets).     

Validation of a gas chromatography–mass spectrometry isotope dilution method for the determination of 2-butoxyethanol and other common glycol ethers in consumer products

A gas chromatography–mass spectrometry isotope dilution (GC–MS ID) method was developed and tested for the determination of 14 common glycol ethers in consumer products. Stable isotope labelled standards, 2-methoxyethanol-D₇ and 2-butoxyethanol-¹³C₂ (CDN isotopes) were employed to enhance the accuracy and precision of the glycol ethers determination. A 1000-fold sample dilution with methanol was applied to avoid column overload and contamination. At this dilution matrix effects were in most cases negligible and did not interfere with the analysis. The instrument detection limit (IDL) for analysed compounds varied from 0.01 to 1 μg/mL; while the estimated limit of quantification (LoQ) varied between different glycol ethers from 0.02 to 3.4 μg/mL. Calibration was tested in the range of 0.1–200 μg/mL and showed that the linear fit is upheld from 0.1 to 10 μg/mL, and extends beyond this range for some of the analytes. Recoveries of glycol ethers from products with different matrices were similar. The recoveries varied from 87% to 116% between the analysed compounds, while measurements precision varied between 2% and 14%. The method is applicable to products with glycol ether concentrations above 0.002–0.2% (w/w). The concentration range can be extended below the specified limits by decreasing the dilution factor; however, with lower dilution the sample matrix effect is expected to be stronger. Products with very high concentrations of glycol ether (>20%) may need to be further diluted prior to injection to avoid column overload. The method can be used for testing liquid and aerosol products designed for household use, such as cleaners, paints, solvents and paint stripers, for compliance and enforcement of regulations which limit glycol ethers content.     

Validation of the RP–HPLC method for analysis of hydrochlorothiazide and captopril in tablets

A rapid and sensitive reverse-phase high performance liquid chromatography (RP–HPLC) method with ultra-violet (UV) detection for a routine control of hydrochlorothiazide and captopril in tablets was developed. The chromatographic system Hewlet Packard 1100 consisted of a HP 1100 pump, HP 1100 UV–VIS detector and HP ChemStation integrator. The samples were introduced through a Rheodyne injector valve with a 20-L sample loop. The isocratic system consisted of a Beckman Ultrasphere ODS 4.6 mm x 15 cm, 5-m-particle column and a mobile phase containing methanol/water (45:55 v/v). The pH of the mobile phase was adjusted to 3.8 with 85% ortophosphoric acid. Quantitation was accomplished using the internal standard method. At the selected conditions, the other excipients of the tablets did not interfere in the assay of active substances. The developed RP–HPLC method was validated, so linearity, precision, accuracy, robustness, limit of quantitation and limit of detection were investigated. For the robustness test, three factors were considered: the composition of the mobile phase , the pH of the mobile phase, and temperature. With the aid of response surface metodology (RSM), it was possible to precisely define the robustness of the method.     

GC–ECD Method for Determination of Glucosidically Bound Aroma Precursors in Fresh Tea Leaves

The possibility of using GC–ECD to determine glucosidically bound aroma precursors was investigated. Five β-d-glucopyranosides were derivatized with N-methyl-bis(trifluoroacetamide) (MBTFA) and then determined by GC-ECD, which showed these mono-glycosides (glucosides) could be separated and identified by GC. Repeatability, sensitivity and stability were tested, relative standard deviation (RSD) was in the range of 0.55–5.9%, the limit of detection (LOD) was lower than 10^?3 μg mL^?1, and the standard mixture was stable within 3 days (stored at 4 °C, peak areas RSD < 3%). Application of the developed derivatization and determination method to the fresh tea leaves showed that the glucosides could be accurately quantified (using phenyl β-d-glucopyranoside as internal standard). Because of its high sensitivity, the developed method was suitable for the determination of glucosides in fresh tea leaves.     

Development of a dispersive liquid–liquid microextraction (DLLME) method coupled with GC/MS as a simple and valid method for simultaneous determination of phthalate metabolites in plasma

Phthalates are ubiquitous environmental contaminants, and frequent biological monitoring of their metabolites (as toxic species of phthalates in human body) is highly recommended. A novel dispersive liquid–liquid microextraction (DLLME) coupled with Gas Chromatography–Mass Spectrometry (GC-MS) has been developed for the determination of seven phthalate metabolites in human plasma for the first time. Plasma proteins were efficiently precipitated by adding of 0.2mg dry trichloroacetic acid to 10 mL plasma samples, incubation and centrifuging. For DLLME, a mixture of extraction solvent (chlorobenzene, 10 µL) and dispersive solvent (acetonitrile, 750 µL) were rapidly injected into 5.0 mL aqueous sample for the formation of cloudy solution, the analytes in the sample were extracted into the fine droplets of chlorobenzene. After extraction, phase separation was performed by centrifugation and the enriched analytes in the sedimented phase were subjected to GC-MS analysis. All important parameters affecting DLLME performance were investigated and optimised. Under the optimum extraction condition, the method yields a linear calibration curve for all target analytes in the concentration range from 5 to 5000 ng mL^?1. The limits of detection and relative standard deviations for all phthalate metabolites were between 1.21–2.09 ng mL^?1 and 4.8–6.8%, respectively. This is a very simple, rapid and reproducible method, which requires low volume of sample and toxic solvents.