二维Ni-Salphen基共价有机骨架的制备及电容性能

利用2,3,6,7,10,11-六氨基三苯六盐酸盐（HATP）和4,6-二羟基-5-甲基间苯二甲醛（DMDB）为构筑基元,构筑了二维Ni-Salphen基共价有机骨架（COFs）电极材料（Ni-Salphen-COF）。通过一系列方法对Ni-Salphen-COF的结构、形貌和电化学性能进行了表征和测试。三电极系统测试结果表明,Ni-Salphen-COF具有优异的电化学性能,在1 A·g^-1时,比电容达到531 F·g^-1,并显示良好的循环稳定性（10 000次循环后电容保持率为89%）。同时,二电极系统测试结果显示,在1 A·g^-1时,Ni-Salphen-COF//AC （AC为活性炭）比电容达176 F·g^-1;在功率密度为900 W·kg^-1时,最大能量密度为55 Wh·kg^-1。良好的性能可能归因于Ni-Salphen结构提高了电极材料的电导率、氧化还原活性和电荷转移能力。     

泡沫镍负载NiMoO4/NiMoS4复合材料的制备及其电化学性能

以泡沫镍作为基底，采用水热法原位生长出具有片状结构的NiMoO₄活性材料，然后通过水热硫化制备出NiMoO₄/NiMoS₄复合材料，研究了水热时间和硫脲添加量对样品形貌和电化学性能的影响。电化学结果表明，NiMoO₄/NiMoS₄电极在电流密度为 1 A·g^-1时，比电容为 1 560.7 F·g^-1，在电流密度为 40 A·g^-1时循环 2 000次后，比电容仍为初始比电容的 76.7%。将 NiMoO₄/NiMoS₄电极材料与活性炭(AC)分别作为正、负极组装的非对称超级电容器(ASC)在 400 W·kg^-1的功率密度下可提供 29.0 Wh·kg^-1的能量密度。     

泡沫镍负载NiMoO4/NiMoS4复合材料的制备及其电化学性能

以泡沫镍作为基底,采用水热法原位生长出具有片状结构的NiMoO₄活性材料,然后通过水热硫化制备出NiMoO₄/NiMoS₄复合材料,研究了水热时间和硫脲添加量对样品形貌和电化学性能的影响。电化学结果表明,NiMoO₄/NiMoS₄电极在电流密度为1A·g^-1时,比电容为1560.7F·g^-1,在电流密度为40A·g^-1时循环2000次后,比电容仍为初始比电容的76.7%。将NiMoO₄/NiMoS₄电极材料与活性炭(AC)分别作为正、负极组装的非对称超级电容器(ASC)在400W·kg^-1的功率密度下可提供29.0Wh·kg^-1的能量密度。     

高性能NiCoP基超级电容器电化学性能

采用水热和低温磷化反应两步法,在无添加沉淀剂条件下成功在泡沫镍上合成纳米花状镍钴磷化物(NiCoP/NF).研究结果表明,镍/钴元素物质的量之比为1∶1时,在1A·g-1电流密度下,Ni1/2Co1/2P/NF的比容量高达1276.36 F·g-1,在10A·g-1电流密度下充放电循环3000次后,比容量保持率为78....     

线状全固态CNTF@ZnCo-OH//CNTF@RGO超级电容器的制备与电化学性能

采用电化学沉积在碳纳米管纤维上复合锌钴氢氧化物纳米片（CNTF@ZnCo-OH）,并研究其电化学性能。实验结果表明CNTF@ZnCo-OH电极在2 A·g^-1的电流密度下比电容为748 F·g^-1,在10 A·g^-1的电流密度下循环2 000圈以后,比电容保持率高达110.4%。该优异循环性能得益于碳纳米管纤维基底的网络结构和ZnCo-OH的纳米片状结构。以CNTF@RGO（石墨烯）为负极、CNTF@ZnCo-OH为正极,组装线状全固态非对称CNTF@ZnCo-OH//CNTF@RGO超级电容器。该器件在0.5 A·g^-1电流密度下比电容为70 F·g^-1,2 000次循环后电容保持率为79.6%,并且在不同的弯曲状态下保持电化学性能不变,具有优良的机械稳定性。该非对称线状器件可以在0.8~1.4 V之间工作,其能量密度高达19.1 Wh·kg^-1,对应的功率密度为1 400.3 W·kg^-1。2个30 mm长的线状器件可持续点亮LED灯10 s。     

Perovskite SrCo0.9Nb0.1O3−δ as an Anion‐Intercalated Electrode Material for Supercapacitors with Ultrahigh Volumetric Energy Density

We have synthesized and characterized perovskite‐type SrCo_0.9Nb_0.1O_3−δ (SCN) as a novel anion‐intercalated electrode material for supercapacitors in an aqueous KOH electrolyte, demonstrating a very high volumetric capacitance of about 2034.6 F cm⁻³ (and gravimetric capacitance of ca. 773.6 F g⁻¹) at a current density of 0.5 A g⁻¹ while maintaining excellent cycling stability with a capacity retention of 95.7 % after 3000 cycles. When coupled with an activated carbon (AC) electrode, the SCN/AC asymmetric supercapacitor delivered a specific energy density as high as 37.6 Wh kg⁻¹ with robust long‐term stability.     

High Energy Density Heteroatom (O,N and S) Enriched Activated Carbon for Rational Design of Symmetric Supercapacitors

Carbon-based symmetric supercapacitors (SCs) are known for their high power density and long cyclability, making them an ideal candidate for power sources in new-generation electronic devices. To boost their electrochemical performances, deriving activated carbon doped with heteroatoms such as N, O, and S are highly desirable for increasing the specific capacitance. In this regard, activated carbon (AC) self-doped with heteroatoms is directly derived from bio-waste (lima-bean shell) using different KOH activation processes. The heteroatom-enriched AC synthesized using a pretreated carbon-to-KOH ratio of 1:2 (ONS@AC-2) shows excellent surface morphology with a large surface area of 1508 m² g⁻¹. As an SC electrode material, the presence of heteroatoms (N and S) reduces the interfacial charge-transfer resistance and increases the ion-accessible surface area, which inherently provides additional pseudocapacitance. The ONS@AC-2 electrode attains a maximum specific capacitance (C_sp) of 342 F g⁻¹ at a specific current of 1 Ag⁻¹ in 1 m NaClO₄ electrolyte at the wide potential window of 1.8 V. Moreover, as symmetric SCs the ONS@AC-2 electrode delivers a maximum specific capacitance (C_sc) of 191 F g⁻¹ with a maximum specific energy of 21.48 Wh kg⁻¹ and high specific power of 14 000 W kg⁻¹ and excellent retention of its initial capacitance (98 %) even after 10000 charge/discharge cycles. In addition, a flexible supercapacitor fabricated utilizing ONS@AC-2 electrodes and a LiCl/polyvinyl alcohol (PVA)-based polymer electrolyte shows a maximum C_sc of 119 F g⁻¹ with considerable specific energy and power.     

ZIFs骨架型双壳层纳米笼状CoS/NiCo2S4的制备及其电化学性能

采用离子刻蚀和化学气相沉积法制备出具有沸石咪唑酯骨架(ZIFs)型双壳层纳米笼状的CoS/NiCo_2S_4并组装成超级电容器。该结构有较大的比表面积(98 m2·g-1),合适的孔道(孔径4 nm),且保留了ZIFs骨架构型。作为电极活性材料时,具有良好的结构稳定性和电化学活性,有利于增强所组装的超级电容器的循环稳定性和比容量。在三电极体系中,在1 A·g-1的电流密度下,容量为1 230 F·g-1;在3 A·g-1电流密度下循环9 000圈后,初始电容保持率为76.6%。在以该电极、活性炭电极与KOH/聚乙烯醇(PVA)凝胶态电解质组装的器件中,当功率密度为702 W·kg-1时,能量密度达31.6 Wh·kg-1;在7 056 W·kg-1的高功率密度下,仍保持16.5 Wh·kg-1的能量密度。     

Surface Modification and Performance of Activated Carbon Electrode Material

A commercial activated carbon was modified by surface treatment using three chemicals, nitric acid, hydrogen peroxide, and ammonia, respectively. The modified carbons were characterized by N₂ adsorption-desorption isotherms and FTIR spectroscopy. The resultant carbon electrode-based electric double-layer capacitors (EDLCs) were assembled with 6 mol·L⁻¹ KOH as the electrolyte. The influence of surface modification on the performance of EDLCs was studied by galvanostatic charge-discharge, cyclic voltammetry, and alternating current impedance. The surface modification resulted in no big decrease in specific surface area and little decrease in average pore size, and introduced functional groups, such as hydroxyl, carbonyl, and amidogen, on the carbon surface. These functional groups significantly improved the wettability and reduced the resistance of the activated carbon. As a result, the specific capacitance of the carbon modified with 65% HNO₃ reached 250 F·g⁻¹, 72.4% higher than that of original carbon. The leakage current of testing EDLCs decreased unexpectedly to 3-18 μA, only 0.8%-4.9% that of the original carbon electrode-based EDLC (371 μA).     

In situ polymerization and reduction to fabricate gold nanoparticle‐incorporated polyaniline as supercapacitor electrode materials

Nanocomposites of gold nanoparticles and polyaniline are synthesized by using HAuCl₄ and ammonium peroxydisulfate as the co‐oxidant involving in situ polymerization of aniline and in situ reduction of HAuCl₄. Through these in situ methods, the synthesized Au nanoparticles of ca. 20 nm embedded tightly and dispersed uniformly in polyaniline backbone. With the Au content in composite increasing from 4.20 to 24.72 wt.%, the specific capacitance of the materials first increased from 334 to 392 F g⁻¹ and then decreased to 298 F g⁻¹. Based on the real content of PANI in composite material, the highest specific capacitance is calculated to be 485 F g⁻¹ at the Au amount of 19.15 wt.%, which remains 55.6% after 5000 cycles at the current density of 2 A g⁻¹. Finally, the asymmetric supercapacitor of AuNP/PANI||AC and the symmetric supercapacitor of AuNP/PANI||AuNP/PANI are assembled. The asymmetric supercapacitor device shows a better electrochemical performance, which delivers the maximum energy density of 7.71 Wh kg⁻¹ with power density of 125 W kg⁻¹ and maximum power density of 2500 W kg⁻¹ with the energy density of 5.35 Wh kg⁻¹.     

在碳纤维布上原位生长NiCo层状双氢氧化物纳米片用于高性能非对称超级电容器

通过恒电压电沉积法在不同的碳纤维基体上原位制备NiCo层状双金属氢氧化物(NiCo-LDH)复合材料(NiCo-LDH/碳纤维布),该方法 无需粘合剂,可以有效避免由于粘合剂的加入引起的导电性降低.在NiCo-LDH的层状晶体结构中,正电荷的主体层和层间电荷补偿阴离子可以促进电极材料之间的离子扩散,从而可高效利用活性位...     

氮掺杂石墨烯量子点/MOF衍生多孔碳纳米片构筑高性能超级电容器

首先采用溶液法在碳布上生长Co-MOF二维纳米片,通过高温退火和刻蚀后得到MOF衍生多孔碳纳米片。以Co-MOF衍生的多孔碳纳米片/碳布(CNS/CC)作为碳基骨架,采用电化学沉积法负载高活性氮掺杂石墨烯量子点(N-GQDs),制备得到分级多孔结构的N-GQD/CNS/CC复合材料。组装成自支撑且无粘结剂的N-GQD/CNS/CC电极,当电流密度为1 A·g~(-1)时,其比电容高达423 F·g~(-1)。通过储能机制和电容贡献机制的研究表明,在碳纤维上原位生长的具有高双电层电容的CNS和表面负载具有高赝电容的N-GQDs之间相互协同作用,使得N-GQD/CNS/CC电极具有高电容性能,是一种理想的超级电容器电极材料。电极材料的高导电、分级多孔结构有利于电子的传输和电解质离子的扩散,具有良好的动力学性能,能快速充放电和具有优异的倍率特性。将电极组装成对称型超级电容器,功率密度为250 W·kg~(-1)时对应的能量密度达到7.9 Wh·kg~(-1),且经过10 000次循环后电容保持率为91.2%,说明氮掺杂石墨烯量子点/MOF衍生多孔碳纳米片复合材料是一种电化学性能稳定的具有高电容性能的全碳电极材料。     

Supercapacitor performance of activated carbon derived from rotten carrot in aqueous,organic and ionic liquid based electrolytes

In this work, we report the synthesis of porous activated carbon (AC). AC was derived from rotten carrot, at different values of activating temperature under inert atmosphere, employing chemical activation method and ZnCl₂ as activation agent. On the basis of results observed by surface area and pore size analysis, effect of activation temperature on synthesized AC was determined. Other material properties such as morphology, thermal stability, vibrational response, and crystal structure of prepared AC were studied using standard techniques of material characterization. Further, the electrochemical performance of synthesized AC was studied as an electrode, in aqueous, organic and ionic liquid based electrolyte. It was found that the synthesized AC based electrode exhibits highest specific capacitance (135.5?F?g^?1 at 10?mHz) in aqueous electrolyte and highest specific energy (29.1?Wh?kg^?1 at 2.2?A?g^?1) and specific power (142.5?kW?kg^?1 at 2.2?A?g^?1) in ionic liquid based electrolyte. This shows the suitability of synthesized material for use in energy storage applications.     

GO/ZIF-67模板制备rGO/NiCo2S4及高性能不对称超级电容器

以氧化石墨烯(GO)为基底,在GO表面原位生长ZIF-67并作为模板,经硝酸镍刻蚀、碳化、水热硫化制得rGO/NiCo_2S_4复合材料。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)表征复合材料的结构与形貌。随后将rGO/NiCo_2S_4复合材料制成正极材料,测试其电化学性能,测试结果显示:rGO/NiCo_2S_4-1.5 h电极材料在1 A·g~(-1)的电流密度下,其比电容值高达1 577 F·g~(-1),当电流密度达到10 A·g~(-1)时,倍率性能为86.4%,在10 A·g~(-1)的电流密度下循环2 000次后,电容保持率为76.9%。另外,在6 mol·L-1KOH电解液中,由AC//rGO/NiCo_2S_4-1.5 h组成的不对称电容器在功率密度为723 W·kg~(-1)时,能量密度为33 Wh·kg~(-1);在高功率密度为7 277 W·kg~(-1)时,能量密度仍保持为23 Wh·kg~(-1)。     

Fluorination effect of activated carbon electrodes on the electrochemical performance of electric double layer capacitors

The surface of phenol-based activated carbon (AC) was fluorinated at room temperature with different F₂:N₂ gas mixtures for use as an electrode material in an electric double-layer capacitor (EDLC). The effect of surface fluorination on EDLC electrochemical performance was investigated. The specific capacitance of the fluorinated AC-based EDLC was measured in a 1 M H₂SO₄ electrolyte, in which it was observed that the specific capacitances increased from 375 and 145 F g⁻¹ to 491 and 212 F g⁻¹ with the scan rates of 2 and 50 mV s⁻¹, respectively, in comparison to those of an unfluorinated AC-based EDLC when the fluorination process was optimized via 0.2 bar partial F₂ gas pressure. This enhancement in capacitance can be attributed to the synergistic effect of increased polarization on the AC surface, specific surface area, and micro and mesopore volumes, all of which were induced by the fluorination process. The observed increase in polarization was derived from a highly electronegative fluorine functional group that emerged due to the fluorination process. The increased surface area and pore volume of the AC was derived from the physical function of the fluorine functional group.     

高能量密度和功率密度炭电极材料

以核桃壳为原料, 采用同步物理-化学活化法制备活性炭(AC). 用氮气吸附法和傅立叶红外光谱(FTIR), 对活性炭的孔结构和表面官能团进行了分析. 以活性炭为电极材料制备炭电极, 6 mol·L-1 KOH溶液为电解液组装成超级电容器, 利用恒电流充放电、循环伏安、交流阻抗等电化学测试方法研究其电化学性能及其与活性炭材料结构的关系. 结果表明, 实验电容器的内电阻、漏电流小, 循环充放电稳定性好, 容量保持率高; 活性炭的比电容随比表面积的增加而增大, 且与BET比表面积呈线性相关; 孔径在1.5-4 nm之间的孔表面有利于形成有效的双电层. 中等比表面积1197 m2·g-1炭样的比电容高达292 F·g-1, 80 mA充放电时, 电容器能量密度高达7.3 Wh·kg-1, 功率密度超过770 W·kg-1,峰值功率密度为5.1 W·g-1.     

Carbon-Encased Mixed-Metal Selenide Rooted with Carbon Nanotubes for High-Performance Hybrid Supercapacitors

Transition metal-based compounds with high theoretical capacitance and low cost represent one class of promising electrode materials for high-performance supercapacitors. However, their low intrinsic electrical conductivity impedes their capacitive effect and further limits their practical application. Rational regulation of their composition and structure is, therefore, necessary to achieve a high electrode performance. Herein, a well-designed carbon-encased mixed-metal selenide rooted with carbon nanotubes (Ni-Co-Se@C-CNT) was derived from nickel–cobalt bimetallic organic frameworks. Due to the unique porous structure, the synergistic effect of bimetal selenides and the in situ growth of carbon nanotubes, the composite exhibits good electrical conductivity, high structural stability and abundant redox active sites. Benefitting from these merits, the Ni-Co-Se@C-CNT exhibited a high specific capacity of 554.1 C g⁻¹ (1108.2 F g⁻¹) at 1 A g⁻¹ and a superior cycling performance, i.e., 96.4% of the initial capacity was retained after 5000 cycles at 10 A g⁻¹. Furthermore, a hybrid supercapacitor assembled with Ni-Co-Se@C-CNT cathode and activated carbon (AC) anode shows a superior energy density of 38.2 Wh kg⁻¹ at 1602.1 W kg⁻¹.     

Highly scalable and low cost binder free electrode of Zinc modified NiO nanofoam for dual role of supercapacitor and its free radical scavenging activity

In this study, pristine nickel oxide (NiO) and Zinc modified NiO nanofoams were prepared by green approach using camellia sinensis leaves extract. Pristine nickel oxide and Zn²⁺ modified NiO nanofoam were characterized by XRD, FTIR, FL, UV and FESEM. FE-SEM micrographs were clearly shows that the synthesised porous nanofoam with spherical shaped were constant distribution. The as prepared foam electrodes showed excellent supercapacitive behaviour with increase in specific capacitance with decrease in scan rate. The maximum specific capacitance 1530, 1706 and 1847Fg^-1 was obtained at scan rate of 10 mVs^-1 for increasing the Zn concentrations. After 3,000 cycles at 1 A g⁻¹, the cyclic stability remains excellent at 88.1% of the initial capacitance. Moreover, the as-prepared asymmetric supercapacitor exhibits a high energy density of 30.6 W h·kg⁻¹ at power density of 398 W kg⁻¹. This study is expected to provide new insights into exploring the potential mechanism of catalyst action. These findings show that Zinc @ NiO nanofoam could be a potentially useful electrode material for energy storage devices.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.