Numerical Modeling of Unsteady Radiative–Convective Heat Transfer on a Flat–Plate Boundary Layer in a Selectively Emitting and Scattering Medium

A conjugation problem for radiative–convective heat transfer in a turbulent flow of a high–temperature gas—particle medium around a thermally thin plate is considered. The plate experiences intense heating from an outside source that emits radiation in a restricted spectral range. Unsteady temperature fields and heat–flux distributions along the plate are calculated. The results permit prediction of the effect of the type and concentration of particles on the dynamics of the thermal state of both the medium in the boundary layer and the plate itself under conditions of its outside heating by a high–temperature source of radiation.     

Interaction between the boundary layer and a supersonic flow when part of the wall is rapidly heated

There have been many theoretical studies of aspects of the unsteady interaction of an exterior inviscid flow with a boundary layer [1–9]. The mathematical flow models obtained in these studies by the method of matched asymptotic expansions describe a wide range of phenomena observed experimentally. These include boundary layer separation near the hinge of a flap, the flow in the neighborhood of the trailing edge of an oscillating airfoil [1–2], and the development and propagation of perturbations in a boundary layer excited by an oscillating wall or some other way [3–5]. The present paper studies the interaction of an unsteady boundary layer with a supersonic flow when a small part of the surface of a body in the flow is rapidly heated.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 66–70, January–February, 1984.     

Free surface asymptotics for thermocapillary flow at high marangoni numbers

Formal asymptotic expansions of the solution of the steady-state problem of incompressible flow in an unbounded region under the influence of a given temperature gradient along the free boundary are constructed for high Marangoni numbers. In the boundary layer near the free surface the flow satisfies a system of nonlinear equations for which in the neighborhood of the critical point self-similar solutions are found. Outside the boundary layer the slow flow approximately satisfies the equations of an inviscid fluid. A free surface equation, which when the temperature gradient vanishes determines the equilibrium free surface of the capillary fluid, is obtained. The surface of a gas bubble contiguous with a rigid wall and the shape of the capillary meniscus in the presence of nonuniform heating of the free boundary are calculated.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 3, pp. 61–67, May–June, 1989.     

Localized Coherent Structures in the Boundary Layer

A Blasius laminar boundary layer and a steady turbulent boundary layer on a flat plate in an incompressible fluid are considered. The spectral characteristics of the Tollmien—Schlichting (TS) and Squire waves are numerically determined in a wide range of Reynolds numbers. Based on the spectral characteristics, relations determining the three–wave resonance of TS waves are studied. It is shown that the three–wave resonance is responsible for the appearance of a continuous low–frequency spectrum in the laminar region of the boundary layer. The spectral characteristics allow one to obtain quantities that enter the equations of dynamics of localized perturbations. By analogy with the laminar boundary layer, the three–wave resonance of TS waves in a turbulent boundary layer is considered.     

Optimization of laminar-turbulent transition delay by means of local heating of the surface

The stability and position of laminar-turbulent transition in the boundary layer on a body heated near the leading edge are analyzed. The point of transition is found using the linear theory of the stability of plane-parallel flow and thee ^N -method. It is shown that by heating a tiny area near the leading edge to a temperature exceeding that of the oncoming flow by a factor of two to four, transition may be delayed, even on a thermally insulated surface. For highly radiating surfaces the energy saved by reducing the friction drag may exceed the heating energy by a factor of three. It is shown that by varying the pressure distribution and surface heating it is possible either to increase the airfoil lift for a fixed transition point or delay transition for a fixed lift.Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 4, pp. 90–99, July–August, 1995.     

The structure of the supersonic turbulent boundary layer in its interaction with a shock wave

An experimental study is made of the turbulent boundary layer in its interaction with a shock wave, the purpose being to clarify questions connected with the increase in the fullness of the velocity profiles. New systematic data are obtained on the development of the boundary layer, and its structure and asymptotic behavior beyond the interaction region. These results are for axisymmetric flow in the range of Mach numbers M=2–4 and angles of rotation of the flow 10–25°. Conditions of developed separation are included. Extensive information about the general properties of flows with separation has been obtained in a number of studies. A survey of these may be found, for example, in [1, 2]. Certain questions about the separation and reattachment of the boundary layer are clarified. The dimensions of the separation region are determined and its structure studied in detail for various shapes of the surface around which the flow takes place. Nevertheless it has not yet proved possible to reach a complete understanding of this complex phenomenon. Usually plane models have been used for the investigations, but in this case it is evidently impossible to exclude completely the influence of end effects on the flow in the interaction zone. Therefore it is preferable to study such flows in axisymmetric models; this considerably eases the task of analyzing and interpreting the results.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 75–82, September–October, 1985.     

Analysis of the three-dimensional turbulent boundary layer on the suface of an arbitrary body at large angles of attack

Three-dimensional compressible gas flow past an arbitrary model body at large angles of attack is analyzed in the framework of the boundary layer theory with allowance for heat transfer. The equations of a three-dimensional turbulent boundary layer are solved using computer codes, the data on the external inviscid flow, and the body geometry.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 3, pp. 55–66, May–June, 1995.     

Asymptotic analysis of turbulent boundary layer flow on a flat plate at high Reynolds numbers

The equations of the turbulent boundary layer contain a small parameter — the reciprocal of the Reynolds number, which makes it possible to carry out an asymptotic analysis of the solutions with respect to that small parameter. Such analyses have been the subject of a number of studies [1–5]. In [2, 5] for closing the momentum equation algebraic Prandtl and turbulent viscosity models were used. In [1, 3, 4] the structure of the boundary layer was analyzed in general form without formulating specific closing hypothesis but under additional assumptions concerning the nature of the asymptotic behavior of the limiting solutions in the various regions.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.4, pp. 106–117, May-June, 1993.     

Development of the boundary layer on a plate in a rotating system

A numerical investigation in the approximation of boundary layer theory has been made of the development of the flow near the surface of a rotating plate in a two-dimensional flow with rectilinear streamlines perpendicular to the leading edge in a rotating coordinate system attached rigidly to the plate. In an earlier investigation [1] using the approximate method of integral relations, Kurosaka obtained and described quantitatively a transition from a Blasius boundary layer to an Eckmann boundary layer in the form of three-dimensional oscillations. The solution described in the present paper confirms the oscillatory nature of the development of the boundary layer, but the quantitative results differ strongly from Kurosaka's.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 3, pp. 154–157, May–June, 1982.     

Supersonic drag of three-dimensional bodies with a star-shaped cross section and its calculation

The effect on the aerodynamic drag of the real properties of the gas in the shock layer around pyramidal star-shaped bodies (the viscosity, the displacement thickness of the boundary layer, its separation under the influence of the inner shocks) is considered. It is shown that the models for calculating the total drag of star-shaped bodies which do not take into account the displacement thickness of the boundary layer are applicable only at low supersonic free-stream velocities (M < 3). A model of the boundary layer displacement thickness is proposed and tested over a broad range of variation of the parameters that determine the geometry of the pyramidal bodies for high supersonic or hypersonic speeds. A comparison with the experimental data shows that the calculation procedure adequately reflects the results of experiments on the aerodynamic drag of star-shaped bodies in cases in which the inner shocks in the shock layer do not lead to boundary layer separation and can be used in optimization problems.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.1, pp. 57–69, January–February, 1993.     

Thermocapillary Vortices Induced by a Light Beam near a Bubble Surface in a Hele-Shaw Cell

This paper studies thermocapillary vortices induced by local heating of a bubble surface in a Hele-Shaw cell by a light beam. It is found that the vortex rotation frequency and its depth depend on the distance from the light-beam projection onto the layer to the bubble boundary. The surface velocity of the thermocapillary flow is calculated using the balance of the near-surface and return flows of the thermocapillary vortex and the equality of capillary and dynamic pressures. It is shown that a decrease in the surface velocity and the vortex rotation frequency with increase in the distance from the light beam to the bubble surface is due to a decrease in the temperature gradient between the illuminated and cold poles of the bubble.__________Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 5, pp. 93–99, September–October, 2005.     

Laminar boundary layer stability on membrane type deformable surfaces

In connection with the successful experiments of Kramer [l, 2] on models sheathed by flexible coverings, attempts have been made to explain theoretically the effect of boundary deformation on the position of the point of stability loss in the boundary layer. Korotkin [3] examined the stability of a plane laminar boundary layer on an elastic surface under the assumption of a linear connection between the pressure perturbation and the normal deformation of the surface. Benjamin [4] and Landahl [5] investigated the stability of the laminar boundary layer on a membrane type surface under the assumption that the physical characteristics of the surface depend on the perturbing flow wavelength. In the following we examine stability of Blasius flow on a membrane type surface whose physical characteristics are constant along the length.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, vol. 10, no. 6, pp. 52–56, November–December, 1969.     

Effect of thermodiffusion on intensity of surface burn-out in a heterogeneous turbulent boundary layer

On the basis of an analysis of the binary diffusion equation in the viscous sublayer of the turbulent boundary layer an estimate is given of the effect of thermodiffusion on the concentration of components at an impervious wall, on the permeability of the wall, and on the intensity of heating of the reactive surface. Experimental results are presented on the burnout of a graphite wall in mixtures of air with nitrogen, argon, and helium.Translated from Zhurnal Prikaldnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 5, pp. 119–125, September–October, 1972.     

Multiparameter boundary layer method for slender bodies of revolution

The problem of the laminar and steady incompressible boundary layer on elongated slender bodies of revolution in an axisymmetric flow is examined in those cases in which the ratio of the boundary layer thickness to the radius of the body's cross section should not be neglected. For this purpose the boundary layer equation for slender bodies of revolution is universalized on the basis of Loitsyanskii's method.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 22–27, November–December, 1991.     

Investigation of pre-separation boundary layer flows on the basis of various algebraic models of turbulence

The problem of the three-dimensional incompressible turbulent boundary layer developing ahead of a circular cylinder mounted at right angles on a flat plate is considered. The direction of the uniform approach stream is normal to the leading edge of the plate. The turbulence is simulated by means of five different isotropic algebraic models of eddy viscosity. The boundary layer equations are solved numerically by means of a second-order-accurate implicit finite-difference method. The principal characteristics of the flow obtained on the basis of the turbulence models selected are compared for a free-stream Reynolds number Re = 10⁷.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 36–43, November–December, 1991.     

Aerodynamics of end-wall boundary layer in a vortex chamber

The need for the inclusion of end-wall boundary layers in the study of the aerodynamics of vortex chambers has been frequently mentioned in the literature. However, owing to limited experimental data [1–3] with reliable information on the wall layers, the existing computational methods for end-wall boundary layers are not well-founded. The question of which parameters determine the formation of end-wall flow remains debatable. In some studies [4, 5], the vortex chambers are conditionally divided into short and long chambers. However, there is no unique opinion on the role of end-wall flows in vortex chambers of different lengths. It has also not been established for what geometric and flow parameters the chamber could be considered long or short. In the present study, as in [1, 5–8], solution is obtained for the end-wall boundary-layer equations using integral methods, considering the boundary layer in the radial direction in the form of a submerged wall jet. Such an approach made it possible to use the laws for the development of wall jets [9], and obtain fairly simple relations for integral parameters, skin friction, mass flow in the boundary layer, and other characteristics. Results are compared with available experimental data and computations of others authors; turbulent flow is considered; results for laminar boundary layer are given in [10].Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 5, pp. 117–126, September–October, 1986.     

Design of a wing airfoil in a flow with a separated turbulent boundary layer

The problem of designing the contour of an airfoil in a viscous (incompressible and compressible) flow with a separated turbulent boundary layer from a pressure distribution given on the separationless part of the contour is solved using the boundary layer theory together with the separated flow model proposed in [1]. Numerical calculations are carried out to demonstrate the possibilities of the method.Kazan'. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.3, pp. 83–91, May–June, 1994.     

Convective heating of a blunt-nosed body in a nonuniform hypersonic gas stream

An investigation is made into the convective heating of a blunt-nosed body in an expanding stream of heated gas. The gas parameters at the outer edge of the boundary layer are determined on the basis of a solution obtained earlier by the authors [3]. Expressions are obtained which make it possible to convert the convective heat flux to a body in a uniform gas stream to one in a nonuniform stream. Dimensionless numbers are found and their influence on the convective heat flux to the body is investigated.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 4, pp. 127–133, July–August, 1981.     

Thermocapillary instability of a plane layer with a vertical temperature gradient

The oscillating disturbances in a plane layer with a temperature gradient are analyzed. It is shown that for heating from below taking the deformability of the free surface into account leads to the appearance of short-wave oscillatory instability, which becomes the most dangerous mode. Moreover, the interaction of the capillary and thermocapillary instability mechanisms results in the appearance of oscillating disturbances of a new type, which lead to equilibrium crisis at high Marangoni numbers. It is established that when the free boundary is heated, the onset of convection is possible only with respect to oscillatory disturbances.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.3, pp. 19–23, May–June, 1992.     

Measurement of the cyanogen concentration profile in a thermal boundary layer on models being destroyed by a heat flux

The distribution of the concentration of the CN radical across the boundary layer was obtained in experiments on metals made of high-temperature materials which were placed in an air stream heated to 8500K. The concentration was calculated on the basis of the measured absolute intensity of radiation of the rotational lines of CN with consideration of the temperature profile obtained in [1], A high-frequency electrodeless discharge was used for heating the air.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 3, pp. 139–141, May–June, 1976.