基于Cu/SiO_x/Al结构的阻变存储器多值特性及机理的研究

采用氧化硅材料构建了Cu/SiOx/Al的三明治结构阻变存储器件.用半导体参数分析仪对其阻变特性进行测量,结果表明其具有明显的阻变特性,并且通过调节限制电流,得到了四个稳定的阻态,各相邻阻态的电阻比大于10,并且具有良好的数据保持能力.在不同温度条件下对各个阻态进行电学测试及拟合,明确了不同阻态的电子传输机理不尽相同:阻态1和阻态2为欧姆传导机制,阻态3为P-F(Pool-Frenkel)发射机制,阻态4为肖特基发射机制.根据电子传输机制,建立了铜细丝导电模型并对Cu/SiOx/Al阻变存储器件各个阻态的电致阻变机制进行解释.     

基于Au/TiO_2/FTO结构忆阻器的开关特性与机理研究

采用简单的一步水热法在FTO导电玻璃上外延生长了锐钛矿TiO_2纳米线,制备了具有Au/TiO_2/FTO器件结构的锐钛矿TiO_2纳米线忆阻器,系统研究了器件的阻变开关特性和开关机理.结果表明,Au/TiO_2/FTO忆阻器具有非易失的双极性阻变开关特性.同时,在103s的时间内,器件在0.1 V的电阻开关比始终保持在20以上,表明器件具有良好的非易失性.此外,器件在低阻态时遵循欧姆导电特性,而在高阻态时则满足陷阱控制的空间电荷限制电流传导机制,同时提出了基于氧空位导电细丝形成与断开机制的阻变开关模型.研究结果表明Au/TiO_2/FTO忆阻器将是一种很有发展潜力的下一代非易失性存储器.     

氧分压对Ni/HfO_x/TiN阻变存储单元阻变特性的影响

采用射频磁控溅射的方法,基于不同氧分压制备的氧化铪构建了Ni/HfO_x/TiN结构阻变存储单元.研究发现,随着氧分压的增加,薄膜表面粗糙度略有降低;另一方面,阻变单元功耗降低,循环耐受性能可达10~3次,且转变电压分布的一致性得到改善.结合电流-电压曲线线性拟合结果及外加温度测试探究了器件的转变机理,得出在低阻态的传导机理为欧姆传导机理,在高阻态的传导机理为肖特基发射机理,并根据氧空位导电细丝理论,对高低阻态的阻变机理进行了详细的理论分析.     

分子包埋纳米粒子薄膜阻变特性研究进展

有机分子包埋纳米粒子阻变薄膜是信息存储领域的研究热点之一,本文从器件电极、介质层结构、纳米粒子种类、阻变机理和柔性弯折等方面,综述了其近年来的研究进展.电极/分子及分子/纳米粒子界面性质对器件阻变特性影响较大,但影响规律及界面调控机理仍待探究;分子结构与纳米粒子的种类、尺度及分布可改变膜内界面性质进而影响阻变特性;器件阻变机理主要包括导电细丝、电荷俘获与释放和电荷转移三种,其中导电细丝又分金属、氧空位和碳细丝.分子包埋纳米粒子薄膜阻变研究现多停留在小规模和静态器件方面,下一步应从连续卷绕制备、纳米粒子分布精确控制和耐弯扭特性等方面深入研究,为实现大面积、低成本、高柔性阻变存储器奠定基础.     

基于ZnO纳米线/PMMA复合材料的柔性阻变式随机存储器

基于ZnO纳米线/有机PMMA复合材料体系制备了柔性阻变式随机存储器,由于复合材料体系的低杨氏模量及高柔性特点,该器件展示了超高的机械耐受性.器件在大角度下弯折104次以上而未见性能退化,且数据保持性良好.器件的阻变存储机制可归因于导电细丝的形成与断裂,其中ZnO纳米线表面上的缺陷在导电细丝构建中起重要作用.     

下电极对ZnO薄膜电阻开关特性的影响

本文采用直流磁控溅射法在三种不同的下电极(BEs)上制备了ZnO薄膜, 获得了W/ZnO/BEs存储器结构. 研究了不同的下电极材料对器件电阻开关特性的影响. 研究结果表明, 以不同下电极所制备的器件都具有单极性电阻开关特性. 在低阻态时, ZnO薄膜的导电机理为欧姆传导, 而高阻态时薄膜的导电机理为空间电荷限制电流. 不同下电极与ZnO薄膜之间的肖特基势垒高度对电阻开关过程中的操作电压有较大的影响, 并基于导电细丝模型对不同下电极上ZnO薄膜的低阻态阻值及reset电流的变化进行了解释. 关键词： ZnO薄膜 电阻开关 下电极     

Ni/HfO_2/Pt阻变单元特性与机理的研究

研究了Ni/HfO2(10 nm)/Pt存储单元的阻变特性和机理.该器件具有forming-free的性质,还表现出与以往HfO2(3 nm)基器件不同的复杂的非极性阻变特性,并且具有较大的存储窗口值(105).存储单元的低阻态阻值不随单元面积改变,符合导电细丝阻变机理的特征.采用X射线光电子能谱仪分析器件处于低阻态时的阻变层HfO2薄膜的化学组分以及元素的化学态,结果表明,Ni/HfO2/Pt阻变存储器件处于低阻态时的导电细丝是由金属Ni导电细丝和氧空位导电细丝共同形成的.     

掺杂富勒烯衍生物阻变存储器存储性质的调控研究

以PS(聚苯乙烯)和PC_(61)BM([6.6]-苯基-C61-丁酸甲酯)为活性材料,通过加入导电性不同的缓冲层材料,优化了阻变存储器件的开关比。制备时分别以金纳米粒子(Au-NPs)、聚3,4-乙烯二氧噻吩/聚苯乙烯磺酸盐(PEDOT∶PSS)、聚乙烯吡咯烷酮(PVP)材料作为器件的缓冲层,得到了开关比可调、存储机制不同的电双稳态器件。测试结果发现缓冲层材料导电性是影响器件开关比的关键因素,当缓冲层材料从绝缘性材料PVP换为导电性良好的金纳米粒子,其开关比从10~2逐渐增大到10~5。另外对于不同结构的存储机制,通过电流电压拟合曲线和能带原理图分析,发现缓冲层材料的导电性质及能级匹配是影响器件存储机制的重要因素。     

铜掺杂氧化锌薄膜阻变特性的研究

以 ZnO：Al为底电极,Cu为顶电极,在同种工艺条件下分别制备了类电容结构的纯ZnO 阻变器件和ZnO：2%Cu阻变器件,分析比较了两种器件的典型I-V特性曲线、置位电压（V_Set）和复位电压（V_Reset）的分布范围、器件的耐久性。结果显示,ZnO：Cu阻变器件较纯ZnO阻变器件有更大的开关比和更稳定的循环性能。另外,研究了 ZnO：Cu阻变器件的阻变机理,通过对其I-V特性曲线分析得出以下结论：ZnO：Cu阻变器件在高阻态遵循空间电荷限制电流效应,低阻态符合欧姆定律。     

基于ZnS量子点与聚合物混合层的有机双稳态器件的记忆特性及其载流子传输机制

用ZnS量子点与poly-4-vinyl-phenol (PVP)复合,通过简单的旋涂法制备了结构为ITO/ZnS:PVP/Al的一次写入多次读取(WORM)的有机双稳态器件。器件起始状态为OFF态,通过正向电压的作用,器件由OFF态转变为ON态,并且在正向或反向电压的作用下,器件始终保持在ON态,表现出良好的一次写入多次读取的存储特性。与不含ZnS量子点的器件相比,含有ZnS量子点的器件表现出明显的双稳态特性,其电流开关比达到10⁴,这说明ZnS量子点在器件中起到存储介质的作用。通过对器件电流-电压(I-V)特性的测试,详细讨论了器件的双稳态特性以及载流子传输机制,并且用不同的传导理论模型分析了器件在ON态和OFF态的电流传导机制。器件I-t曲线表明器件在大气环境中具有良好的永久保持特性。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.