聚（N，N＇-二乙基丙烯酰胺）水凝胶的制备及其溶胀动力学

以N,N’-二乙基丙烯酰胺（DEA）为单体,偶氮二异丁腈（AIBN）为引发剂,分别采用疏水性的1,2-二乙烯苯（DVB）和水溶性的N,N’-亚甲基双丙烯酰胺（BIS）为交联剂制备了温度敏感水凝胶聚（N,N’-二乙基丙烯酰胺）（PDEA）。制得的PDEA水凝胶的低临界溶解温度（LCST）在30℃附近,初步讨论了交联剂的用量和性质对水凝胶性能的影响。并对其在不同温度下达到溶胀平衡时的溶胀比,去溶胀动力学及干凝胶的再溶胀动力学过程进行了研究。     

聚(N,N′-二乙基丙烯酰胺)水凝胶的制备及其溶胀动力学

以N,N′-二乙基丙烯酰胺(DEA)为单体,偶氮二异丁腈(AIBN)为引发剂,分别采用疏水性的1,2-二乙烯苯(DVB)和水溶性的N,N′-亚甲基双丙烯酰胺(BIS)为交联剂制备了温度敏感水凝胶聚(N,N′-二乙基丙烯酰胺)(PDEA).制得的PDEA水凝胶的低临界溶解温度(LCST)在30 ℃附近,初步讨论了交联剂的用量和性质对水凝胶性能的影响.并对其在不同温度下达到溶胀平衡时的溶胀比,去溶胀动力学及干凝胶的再溶胀动力学过程进行了研究.     

聚N,N-二乙基丙烯酰胺蒙脱土纳米复合物的合成及溶胀性能

在制成钠基蒙脱土的基础上 ,对蒙脱土进行了改性 ,并把改性后的蒙脱土分散在N ,N 二乙基丙烯酰胺水溶液中进行聚合 .结果表明这种蒙脱土插层聚合的水凝胶的低温溶胀性能大大提高 ,其对水的释放曲线在特定的温度下也由S形转变为近一直线形 .由于蒙脱土的改性 ,在蒙脱土和聚合物之间的界面化学发生了改变 ,用X衍射分析表明此水凝胶是纳米复合材料 .而加入蒙脱土量达 10 %的水凝胶的溶胀比和温度响应性能也都发生很大改善 .     

CMC/PNIPAAm半互穿网络水凝胶的溶胀动力学研究

以羧甲基纤维素钠(CMC)和N-异丙基丙烯酰胺(NIPAAm)为原料,制备了具有温度和pH敏感性的半互穿网络(CMC／PNIPAAmsemi-IPN)水凝胶,并研究了水凝胶在不同温度和pH值条件下的溶胀行为。结果表明：在弱碱性(pH-7．4)条件下,凝胶的溶胀速率和溶胀度都随着凝胶中CMC含量的增加而增大;而在酸性(pH-1．O)条件下则相反。在弱碱性条件下,水分子在凝胶中的扩散行为都可用non-Fickian扩散来描述,水分子在凝胶中的扩散系数D随着凝胶溶胀速率的增大而增大;在酸性条件下,20℃时凝胶的溶胀过程符合non-Fickian扩散规律,而37℃时凝胶的溶胀过程符合Fickian扩散规律,但水分子的扩散系数D相差不大。     

温度及pH敏感聚（丙烯酸）／聚（N—异丙基丙烯酰胺）互穿聚合物网络水凝胶的...

合成聚（丙烯酸）／聚（Ｎ－异丙基丙烯酰胺）互穿聚合物网络（ＰＡＡｃ／ＰＮＩＰＡ ＩＰＮ）水凝胶，具有温度及ｐＨ双重敏感特性。这种水凝胶在弱碱性条件下的溶胀率远大于酸性条件下的溶胀率。在酸性条件下，随着温度上升，凝胶的溶胀率也随之逐渐上升；而在弱碱性条件下，温度低于聚（Ｎ－异丙基丙烯酰胺）（ＰＮＩＰＡ）的较低临界溶解温度（ＬＣＳＴ）时，溶胀率也随着温度的上升而上升，而温度达到ＬＣＳＴ时，凝胶的溶胀率     

前端聚合制备多孔聚丙烯酰胺水凝胶——溶剂和引发剂对反应和产物的影响

利用前端聚合结合发泡工艺制备了孔结构可调控的聚丙烯酰胺多孔水凝胶.研究发现溶剂和引发剂浓度变化对聚合前端的移动及形成的产物性能有重要影响.增加溶剂用量,聚合前端的移动速度和聚合前端最高温度下降,产物孔径增大,孔壁变厚,材料吸水溶胀性能降低;增加引发剂浓度,聚合前端移动速度显著加快,最高温度升高,产物的孔体积和溶胀率先增加后减小.     

温度及pH敏感聚(丙烯酸)/聚(N-异丙基丙烯酰胺)互穿聚合物网络水凝胶的合成及性能研究

合成聚（丙烯酸）／聚（Ｎ 异丙基丙烯酰胺）互穿聚合物网络（ＰＡＡｃ／ＰＮＩＰＡＩＰＮ）水凝胶，具有温度及ｐＨ双重敏感特性．这种水凝胶在弱碱性条件下的溶胀率远大于酸性条件下的溶胀率．在酸性条件下，随着温度上升，凝胶的溶胀率也随之逐渐上升；而在弱碱性条件下，温度低于聚（Ｎ 异丙基丙烯酰胺）（ＰＮＩＰＡ）的较低临界溶解温度（ＬＣＳＴ）时，溶胀率也随着温度的上升而上升，当温度达到ＬＣＳＴ时，凝胶的溶胀率突然急剧下降，并随着温度的逐渐上升而下降．     

多孔聚N-异丙基丙烯酰胺水凝胶的制备与缓释性能

以N-异丙基丙烯酰胺(NIPA)、N,N-亚甲基双丙烯酰胺(MBA)和聚乙二醇(PEG)为原料,以60Co-γ射线为放射源制备了快速响应聚N-异丙基丙烯酰胺(PNIPA)多孔水凝胶。用红外光谱分析了水凝胶的结构,并测定了水凝胶的溶胀动力学、退溶胀动力学和平衡溶胀率。结果表明,PEG分子仅在聚合交联过程中充当成孔剂,不参与反应,反应后可被除去;水凝胶具有明显的温度敏感性,成孔剂的添加提高了水凝胶的溶胀性能和LCST。选用阿司匹林为模型药物,对水凝胶的药物缓释性能进行了初步研究。     

丝素蛋白纤维/聚N-异丙基丙烯酰胺复合水凝胶的性能

以丝素蛋白纤维为填充材料,采用自由基聚合的方法制备复合聚N-异丙基丙烯酰胺(PNIPPAm)水凝胶,研究复合水凝胶的黏弹性能、溶胀性能和反复溶胀-收缩性能。结果表明:丝素蛋白纤维的加入改善了复合水凝胶的力学性能,其平衡溶胀率不仅与温度有关,而且与丝素蛋白纤维的含量有关。此外,处在表面的丝素蛋白纤维与水凝胶之间存在间隙,在反复溶胀-收缩过程中可以作为输水通道,有利于水分子进出,提高了PNIPPAm水凝胶对温度的响应速率并使其溶胀-收缩重复性更好。     

明胶-聚异丙基丙烯酰胺水凝胶的溶胀动力学

采用明胶（Gel)和N－异丙基丙烯酰胺（NIPAM）为原料，制备了Gel/聚异丙基丙烯酰胺（PNIPAM）水凝胶系列；研究了原料配比、pH值及温度对水凝胶溶胀速度的影响。结果表明，当温度大于PNIPAM的最低临界溶液温度（LCST）值时，Gel/PNIPAM水凝胶的溶胀速度随着组分中PNIPAM的增加而降低，且溶胀过程以扩散渗透控制为主。而pH对水凝胶溶胀速度的影响与温度有关。Gel/PNIPAM配比为5／5，温度大于LCST时，水凝胶的pH敏感性受明胶控制；温度低于LCST时，pH对水凝胶的溶胀速度的影响很小。     

ON SWELLING CHARACTERISTICS AND MECHANISM OF TEMPERATURE SENSITIVE HYDROGELS

A series of N-substituted acrylamide monomers and the temperature sensitive hydrogels of their copolymer with N, N'-methylene-bis -acrylamide (Bis) have been synthesized. The effects of monomer structures, composition of the initial monomer mixture, polymerization temperature, the extent of ionization of the network and the presence of acid, base, salt or organic compound on the formation and the swelling characteristics of the temperature sensitive hydrogels have been systematically studied. The mechanism of the temperature sensitive phase transformation of the hydrogels was also investigated.     

Chemically Crosslinked pH- and Temperature-Sensitive (N-isopropylacrylamide-co-1-vinyl-2-pyrrolidone) Based on New Crosslinker: I. Swelling Behavior

Novel pH- and temperature-sensitive polymer matrices based on N-isopropylacrylamide have been developed. The hydrogels were prepared by bulk radical polymerization of N-isopropylacrylamide and 1-vinyl-2-pyrrolidinone in appropriate amounts of distilled water using different mol% of traditional N,N-methylene bisacrylamide (MBA) and the new synthesized N,N,N-tris acryloyl melamine (MAAm) crosslinkers. Lower critical solution transition temperatures (LCST) were measured by differential scanning calorimetry. The synthesized hydrogels have LCST lower than 40°C. The influence of environmental conditions such as temperature and pH on the swelling behavior of these polymeric gels was investigated. The swelling behaviors of the resulting gels show pH sensitivity. The crosslinked NIPAAm/VP with MAAm hydrogels exhibited more rapid deswelling rate than NIPAAm/VP hydrogels crosslinked with MBA in pure water in response to abrupt temperature changes from 20°C to 50°C.     

光化学合成快速响应聚(N,N-二甲基丙烯酰胺-co-N-异丙基丙烯酰胺)水凝胶

通过光化学合成方法分别在高温(50℃)和室温(28℃)下实现了N,N-二甲基丙烯酰胺(DMAA)和N-异丙基丙烯酰胺(NIPAm)的交联共聚,制备了两种不同结构的P(DMAA-co-NIPAm)共聚物水凝胶.对两种温度下制备的P(DMAA-co-NIPAm)共聚物水凝胶的网络结构、溶胀与消溶胀速率和温度敏感性等方面进行了比较研究.结果发现,50℃下制备的P(DMAA-co-NIPAm)共聚物凝胶具有较为疏松的网络结构和相对较快的溶胀速率及温度响应特性.光化学合成方法较传统的热聚合制备方法具有简便、快捷的特点,合成过程仅需2 min.     

Thermoresponsive behavior of poly(n-isopropylacrylamide) hydrogels containing gold nanostructures

We report the changes in the structure and thermoresponsive behavior of poly(N-isopropylacrylamide) (PNIPAm) hydrogels when gold nanostructures are synthesized in situ within the hydrogel matrix. Cross-linked PNIPAm hydrogels were synthesized using NIPAm and 0.00-3.50% (w/w versus NIPAm) of N,N'-methylenebisacrylamide (MBAm) and/or N,N'-cystaminebisacrylamide (CBAm) as cross-linking agents. The hydrogels were soaked in potassium tetrachloroaurate to introduce gold ions. The hydrogels containing Au3+ were then immersed in a sodium borohydride solution to reduce the gold ions. Infrared spectroscopy, UV-visible spectroscopy, and equilibrium swelling were used to examine the structural/physical differences between gels of different compositions; UV-visible spectroscopy and mass measurements were used to observe the kinetics and thermodynamics of the hydrogel volume phase transition. These studies revealed several differences in the physical characteristics and thermoresponsive behavior of hydrogels based on cross-linker identity and the presence or absence of gold nanostructures. Hydrogels with gold nanostructures and high CBAm and low MBAm content have equilibrium swelling masses 3-20 times their native analogues. In comparison, gold-containing hydrogels with high MBAm and low CBAm content have swelling masses that are equal to their native analogues. Additionally, the gold-containing PNIPAm hydrogels cross-linked with only CBAm have a deswelling temperature of approximately 40 degrees C, approximately 8 degrees C above the samples cross-linked with only MBAm. Varying the CBAm content and introducing gold enables tuning of the deswelling temperature.     

Thermodynamic properties of chitosan-based hydrogels in the range 0–350 K

The heat capacity, the temperature, and the enthalpy of physical transformations of hydrogels based on the copolymer of acrylamide and chitosan with N,N-methylene-bis(acrylamide) as a crosslinking agent, hydrogels based on the mixture of poly(vinylpyrrolidone) and chitosan with glutaric aldehyde as the crosslinking agent, and dehydrated hydrogels has been studied in the range 85–350 K with the use of adiabatic vacuum calorimetry. The temperatures and enthalpies of melting of free water in hydrogels have been determined. From the experimental data obtained, the thermodynamic functions C° _p (T), H° (T) ? H°(0), S° (T) ? S°(0), and G° (T) ? H°(0) have been calculated for the temperature range 0–350 K. The ratio of free and bound water in the hydrogels under study has been determined by calorimetry.     

Phase Transition Temperature Controllable Poly(acrylamide-co-acrylic acid) Nanocomposite Physical Hydrogels with High Strength

Poly(acrylamide-co-acrylic acid) nanocomposite physical(P(AAm-co-AAc)NCP) hydrogels have been prepared through the in situ free radical solution polymerization based on a "single network, dual cross-linkings" strategy. The P(AAm-co-AAc) NCP hydrogels are composed of nanobrushes of P(AAm-co-AAc) chains grafted on the surface of vinylhybrid silica nanoparticles(VSNPs). In the hydrogel system, the VSNPs act as the "analogous chemical cross-linking points"once the hydrogen bonds formed between the P(AAm-co-AAc) chains of the nanobrushes, thus leading to the fabrication of high-strength P(AAm-co-AAc) NCP hydrogels. Compared with conventional thermosensitive P(AAm-co-AAc) hydrogels,the P(AAm-co-AAc) NCP hydrogels have a broader range of phase transition temperature, which can be adjusted by altering the monomer ratio, the VSNPs concentration, the addition of urea and N,N-dimethylacrylamide(DMAAm). At the same time, the mechanical properties of the P(AAm-co-AAc) NCP hydrogels have been improved significantly by the introduction of VSNPs. Furthermore, both the phase transition and the tensile strength of the P(AAm-co-AAc) NCP hydrogels are largely influenced when Fe3+ ions are introduced as the ionic crosslinkers into the hydrogel networks.     

NIPAM共聚物多孔水凝胶的光引发RAFT合成及其溶胀性能

采用光引发可逆加成-断裂链转移(RAFT)方法,在室温下先合成了链端含有三硫代碳酸酯基的大分子链转移剂聚(N,N'-二甲基丙烯酰胺)(PDMAM),然后与N-异丙基丙烯酰胺(NIPAM)、N,N'-二甲基双丙烯酰胺(BIS)交联共聚合,并通过聚乙二醇的制孔作用制得PNIPAM-g-PDMAM梳型/多孔水凝胶.采用FTI...     

Preparation and Characterization of Poly(N‐Vinylpyrrolidone‐co‐Methacrylic Acid) Hydrogels

In this study, N‐vinylpyrrolidone (VP)/methacrylic acid (MAA) copolymers have been prepared at three different mole percents, the methacrylic acid composition being around 5, 10, 15%. MAA and VP monomer mixtures have been irradiated in ⁶⁰Co‐γ source at different irradiation doses and percent conversions have been determined gravimetrically. ～80% conversion of monomers into hydrogels were performed at 3.4 kGy irradiation dose. These hydrogels were swollen in distilled water at pH 4.0, 7.0, and 9.0. P(VP/MAA) hydrogel which contains 5% methacrylic acid showed the maximum % swelling at pH 9.0 in water. Diffusion of water was found to be of non‐Fickian character. Diffusion coefficients of water in P(VP/MAA) hydrogels were calculated. Initial swelling rates of P(VP/MAA) hydrogels increased with increasing pH and MAA content in hydrogels. Swelling kinetics of P(VP/MAA) hydrogels was found to be of second order. Thermal behavior of PMAA, PVP and P(VP/MAA) hydrogel were investigated by thermal analysis. P(VP/MAA) hydrogel gained new thermal properties and the temperature for maximum weight loss and temperature for half‐life of P(VP/MAA) hydrogel were determined.     

K-型卡拉胶/聚乙烯吡咯烷酮共混水凝胶的辐射合成

采用辐射技术合成了K 型卡拉胶 (KC) /聚乙烯吡咯烷酮 (PVP)共混水凝胶 ,研究了天然高分子KC、单体N 乙烯基吡咯烷酮 (N VP)、交联剂二甲基丙烯酸十四甘醇酯 ( 1 4G) ,辐照剂量以及剂量率等对辐射合成的KC/PVP共混水凝胶性质的影响 .实验发现 ,KC与适当比例的N VP共混后在一定剂量范围内辐照可得到高强度、高溶胀行为的KC/PVP共混水凝胶 ,随着共混凝胶内KC含量的相对增加 ,凝胶强度及溶胀性的能均显著提高 ,但合成该共混凝胶的最佳剂量却相对提前 ;加入 1 4G后降低了KC/PVP共混凝胶辐射合成最佳剂量 ,同时使KC/PVP共混凝胶的强度进一步提高 ;剂量、剂量率对KC/PVP共混凝胶的性质亦有很大的影响 .分析表明 ,KC与N VP共混后 ,在较低剂量下KC的降解被抑制 ,从而获得一种由物理交联的KC和化学交联的PVP形成的互穿网络 (IPN)凝胶     

Synthesis and thermal properties of a novel lactose‐containing poly(N‐isopropylacrylamide‐co‐acrylamidolactamine) hydrogel

An improved, simple, and efficient method for the synthesis of lactose‐containing monomer acrylamidolactamine (LAM) has been reported. Free radical copolymerization of this monomer with N‐isopropylacrylamide (NIPAM) in the presence of the crosslinking reagent N,N′‐methylenebisacrylamide (BisA) (1.2 mol %) proceeded smoothly in an aqueous solution using potassium persulfate (KPS) and N,N,N′,N′‐tetramethylethylenediamine (TMEDA) as the initiating system and gave transparent hydrogels. Reactivity ratios were estimated from copolymerization reactions carried out in solution without BisA crosslinker and at low conversion, by using both linearization and nonlinearization methods. They were found to be r_LAM = 0.75 and r_NIPAM = 1.22. The swelling behavior of the hydrogels was studied by immersion of the hydrogels in deionized water at different temperatures. Equilibrium water uptake was increased when the LAM content was higher than 47 mol %, and reached ≈ 44‐fold with 100 mol % LAM at room temperature. Depending on the composition, the gels showed sharp swelling transitions with small changes in temperature. Differential scanning calorimetry (DSC) was used to characterize the swelling transition and the organization of water in the copolymer hydrogels. The amounts of freezable water in these hydrogels ranged from 81 to 89%, and was not correlated to the content of the sugar monomer. These gels have potential applications as biocompatible materials. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1393–1402, 1999