Surface properties of LiCoO2, LiNiO2 and LiNi1−xCoxO2

The surface composition and chemical environment of LiCoO₂, hexagonal LiNiO_2, cubic LiNiO₂, and the mixed transition metal oxide LiNi_0.5Co_0.5O₂ have been determined by Auger electron and X-ray photoelectron spectroscopies. While the LiCoO₂ surface properties can easily be extrapolated from bulk composition, the nickel-containing materials are less straightforward. Their surface concentration tends to be depleted in lithium relative to that of the bulk and shows an atypical chemical environment for the constituent elements. The Ni 2p XPS photoemission suggests a near “ NiO-like” selvedge through the XPS binding energies and satellite structure which are essentially identical to that of NiO; the spectrum appears fairly insensitive to lithium concentration. Although there is little evidence for higher binding energy Ni³⁺ species or for an electron poor Ni^2.δ+-derived band structure in the XPS, the lattice oxygen is very electron-rich and yields among the lowest binding energies reported for a transition metal oxide. The nickel-containing lithium oxide selvedge is thus not simply “NiO” and the surface lithium cations have a measurable effect on the electronic structure even in their more highly depleted levels. This is explained in the context of the charge-transfer model of the oxide band structure.     

Thermoelectric properties of sol-gel derived cobaltite Bi2Ca2.4Co2Oy

Layered misfit cobaltite Bi₂Ca_2.4Co₂O_y has been synthesized by a sol-gel method. This compound exhibits large thermoelectric (TE) power (S_300 K∼170 μV K⁻¹), low resistivity (ρ_300 K∼42 mΩ cm) and relatively small thermal conductivity (κ_300 K∼2.8 W K⁻¹ m⁻¹) at room temperature. Furthermore, the resistivity of this compound displays a metallic behavior above T^?∼150 K with a semiconducting behavior below this temperature. This abnormal behavior in resistivity is analogous to those observed in Sr and Ba based misfit cobaltites. The observed features of the TE have been discussed based on the narrow band model.     

Electro-precipitation of Fe3O4 nanoparticles in ethanol

The preparation of superparamagnetic magnetite (Fe₃O₄) nanoparticles by electro-precipitation in ethanol is proposed. Particle average size can be set from 4.4 to 9 nm with a standard deviation around 20%. Combination of wide-angle X-ray scattering (WAXS), Electron energy loss spectroscopy (EELS) and Mössbauer spectroscopy characterizations clearly identifies the particles as magnetite single-crystals (Fe₃O₄).     

Synthesis and physical properties of mixed Co3O4/CoO nanorods by microwave hydrothermal technique

A mixture of crystalline Co₃O₄/CoO nanorods with non-uniform dense distribution has been successfully synthesized by microwave hydrothermal technique. The synthesized nanorods have been characterized by several techniques such as X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), and Fourier transforms infrared spectroscopy (FT-IR). The results showed that the as synthesized specimens contained mixed crystalline Co₃O₄/CoO nanorods with an average length of around 80 nm and an average diameter of 42 nm. UV–Vis spectrum of the nanorods exhibited a strong UV emission. The band energy gap of the product was 1.79 eV which lies between the energy gap of CoO and that for Co₃O₄. The obtained carrier concentration is of the order 4.32 × 10²⁷ m⁻³ and the dielectric constant is found to be 4.89. The electrical conductivity increases with increasing temperature and behaves as a semiconducting material with an activation energy of a bout 0.26 eV. This makes the as synthesized mixed Co₃O₄/CoO nanorods very useful for supercapacitor devices application. Magnetic hysteresis loops at room temperature of the as synthesized mixed oxides (Co₃O₄/CoO) nanorods exhibit typical soft magnetic behavior.     

Preparation, characterization and oxide ion conductivity in U-substituted Bi4V2O11

A Bi₂V_{1 − x − y}U_xBi_yO_{5.5 + 0.5x − y} solid solution derived from Bi₄V₂O₁₁ has been prepared and characterized with x up to 0.125 for y = 0. Partial substitution of U⁶⁺ for V⁵⁺ in Bi₄V₂O₁₁ leads to the stabilization at room temperature of the high-oxide ion conducting γ-phase, in contrast with other M⁶⁺ dopants which stabilize the β-phase. The lower conductivity in U substituted system compared with BICUVOX.10 is attributed to its higher activation energy. Conductivity values and activation energies of the U substituted phases compare well with Bi₂UO₆.     

Modification in structural and optical properties of ZnO, CeO2 doped Al2O3-PbO-B2O3 glasses

The structural and optical analysis of glasses is carried out by XRD, FTIR, density and UV visible spectroscopic measurement techniques. XRD results have confirmed the glassy nature of the samples. The FTIR spectral analysis reveals that with the combined presence of ZnO and CeO₂ contents in Al₂O₃-PbO-B₂O₃ glasses, more BO₃ groups are transformed into BO₄. The optical analysis reveals that optical band gap energy decreases more for CeO₂-ZnO-Al₂O₃-PbO-B₂O₃ glasses (from 2.28 to 1.84 eV). The presence of CeO₂ and ZnO in the glass samples causes more compaction of the borate network due to the formation of more BO₄ groups and the presence of ZnO₄ groups, which results an increase in density, refractive index and decrease of molar volume.     

La2O3对Yb:Y2O3透明陶瓷光谱性能的影响

研究了La₂O₃对Yb：Y₂O₃透明陶瓷光谱性能的影响，添加适量La₂O₃以后，Yb：Y₂O₃透明陶瓷的吸收峰和发射峰的位置不变，但由于La³⁺的离子半径大于Y³⁺的离子半径，在Y₂O₃中引入La³⁺离子后，导致Y₂O₃晶格常数变大，晶场强度变弱，同时降低了Y₂O₃晶体的有序度，致使发射峰强度有所下降，发射截面变小.过量的La₂O₃（x=0.16）造成Yb³⁺激活离子发射强度明显下降；其荧光寿命在添加La₂O₃后总体增大45%—60%. 关键词： 氧化镧 氧化钇 透明陶瓷 光谱性能     

Effects of synthesis variables on the magnetic properties of CoFe2O4 nanoparticles

Cobalt ferrite nanoparticles (CoFe₂O₄) have been synthesized using precipitation in water solution with polyethylene glycol as surfactant. Influence of various synthesis variables included pH, reaction time and annealing temperature on the magnetic properties and particle sizes has also been studied. Structural identification of the samples was carried out using Thermogravimetric and Differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy, Scanning electron microscopy, High resolution transmission electron microscopy. Vibrating sample magnetometer was used for the magnetic investigation of the samples. Magnetic properties of nanoparticles show strong dependence on the particle size. The magnetic properties increase with pH of the precipitating medium and annealing temperature while the coercivity goes through a maximum, peaking at around 25 nm.     

Physical properties of the cubic spinel LiMn2O4

We have performed an ab initio study of structural, electronic, magnetic, vibrational and thermal properties of the cubic spinel LiMn₂O₄ by employing the density functional theory, the linear-response formalism, and the plane-wave pseudopotential method. An analysis of the electronic structure with the help of electronic density of states shows that the density of states at the Fermi level (N (E_F)) is found to be governed by the Mn 3d electrons with some contributions from the 2p states of O atoms. It is important to note that the contribution of Mn 3d states to N(_EF)$N\left(E_F\right)$ is as much as 85%. From our phonon calculations, we have obtained that the main contribution to phonon density of states (below 250 cm⁻¹) comes from the coupled motion of Mn and O atoms while phonon modes between 250 cm⁻¹ and 375 cm⁻¹ are characterized by the vibrations of all the three types of atoms. The contribution from Li increases rapidly at higher frequency (above 375 cm⁻¹) due to the light mass of this atom. Finally, the specific heat and the Debye temperature at 300 K are calculated to be 249.29 J/mol K and 820.80 K respectively.     

Thermoluminescent properties of a Li2O-B2O3-Al2O3 glass system doped with CaF2 and Mn

A Li₂O-B₂O₃-Al₂O₃ glass system doped with CaF₂ and Mn was synthesized by fusion and its physical properties were investigated using thermoluminescence (TL) and differential thermal analysis (DTA) techniques. The TL glow curve peaks, resulting from this analysis, are characteristic of metastable levels intrinsic to CaF₂ crystals that have undergone γ-ray irradiation from a colbalt-60 (⁶⁰Co) source. This provides evidence of CaF₂ crystal formation in the glass system. Furthermore, the TL glow peak at about 480 K was stable at room temperature, sensitive to ⁶⁰Co γ-rays and showed good linearity with doses ranging from 3 Gy to approximately 100 Gy, and consequently could be used to quantify radiation doses. High quality synthesis of these crystals permits control of their thermoluminescent properties.     

Thermal properties of high-k Hf1-xSixO2

Classical atomistic simulations based on the lattice dynalnics theory and the Born core-shell model are performed to systematically study the crystal structure and thermal properties of high-k Hfl-xSixO2. The coefficients of thermal expansion, specific heat, Griineisen parameters, phonon densities of states and Debye temperatures are calculated at different temperatures and for different Si-doping concentrations. With the increase of the Si-doping concentration, the lattice constant decreases. At the same time, both the coefficient of thermal expansion and the specific heat at a constant volume of Hf1-mSixO2 also decreases. The Griineisen parameter is about 0.95 at temperatures less than 100 K. Compared with Si-doped HfO2, pure HfO2 has a higher Debye temperature when the temperature is less than 25 K, while it has lower Debye temperature when the temperature is higher than 50 K. Some simulation results fit well with the experimental data. We expect that our results will be helpful for understanding the local lattice structure and thermal properties of Hf1-mSixO2.     

Optical and electronic properties of NiFe2O4 and CoFe2O4 thin films

We report the optical and electronic properties of the inverse spinel ferrite NiFe₂O₄ and CoFe₂O₄ thin films deposited on single crystal sapphire by electron beam deposition. We carried out variable temperature (78–500 K) transmittance measurements on the thin films to investigate the optical properties and electronic structures of these ferrites. The absorption spectra of both NiFe₂O₄ and CoFe₂O₄ thin films show insulating characters with Ni (Co) d to d on-site transitions below 3 eV. The energy bands above 3 eV are mainly due to the O 2p to Fe 3d charge transfer transitions. The observed electronic transitions have been assigned based on the first principles calculations and comparisons with structurally similar Ni and Co-containing compounds. The Co²⁺ d to d transition in the CoFe₂O₄ thin film shows a strong temperature dependence, likely due to the spin-charge coupling effect.     

Structural, microstructural and magnetic properties of NiFe2O4, CoFe2O4 and MnFe2O4 nanoferrite thin films

The structural, microstructural and magnetic properties of nanoferrite NiFe₂O₄ (NF), CoFe₂O₄ (CF) and MnFe₂O₄ (MF) thin films have been studied. The coating solution of these ferrite films was prepared by a chemical synthesis route called sol-gel combined metallo-organic decomposition method. The solution was coated on Si substrate by spin coating and annealed at 700 °C for 3 h. X-ray diffraction pattern has been used to analyze the phase structure and lattice parameters. The scanning electron microscopy (SEM) and atomic force microscopy (AFM) have been used to show the nanostructural behavior of these ferrites. The values of average grain's size from SEM are 44, 60 and 74 nm, and from AFM are 46, 61 and 75 nm, respectively, measured for NF, CF and MF ferrites. At room temperature, the values of saturation magnetization, M_s∼50.60, 33.52 and 5.40 emu/cc, and remanent magnetization, M_r∼14.33, 15.50 and 1.10 emu/cc, respectively, are observed for NF, CF and MF. At low temperature measurements of 10 K, the anisotropy of ferromagnetism is observed in these ferrite films. The superparamagnetic/paramagnetic behavior is also confirmed by χ′(T) curves of AC susceptibility by applying DC magnetizing field of 3 Oe. The temperature dependent magnetization measurements show the magnetic phase transition temperature.     

First-principles calculations of electronic, optical and elastic properties of ZnAl2S4 and ZnGa2O4

The optimized crystal structures, band structures, partial and total densities of states (DOS), dielectric functions, refractive indexes and elastic constants for ZnAl₂S₄ and ZnGa₂O₄ were calculated using the CASTEP module of Materials Studio package. Pressure effects were modeled by performing these calculations for different values of external hydrostatic pressure up to 50 GPa. Obtained dependencies of the unit cell volume on pressure were fitted by the Murnaghan equation of state, and the relative changes of different chemical bond lengths were approximated by quadratic functions of pressure. Variations of applied pressure were shown to produce considerable re-distribution of the electron densities around ions in both crystals, which is evidenced in different trends for the effective Mulliken charges of the constituting ions and changes of contour plots of the charge densities. The longitudinal and transverse sound velocities and Debye temperatures for both compounds were also estimated using the calculated elastic constants.     

Opto-electronic response of spinels MgAl2O4 and MgGa2O4 through modified Becke-Johnson exchange potential

A first-principles technique capable of describing the state accurately near to excited states of semiconductors and insulators, namely the modified Becke-Johnson (mBJ) exchange potential approximation is used to investigate the opto-electronic response of magnesium spinel oxides: MgAl₂O₄ and MgGa₂O₄. The predicted bandgaps using the mBJ exchange approximation show a significant improvement over previous theoretical work using the common LDA and GGA, and are very closer to the experimental results. Band gap dependent optical parameters, like dielectric constant, index of refraction, reflectivity and optical conductivity are calculated and analyzed.     

Second-harmonic scattering by domains in RbH2PO4 ferroelectrics

Second-harmonic scattering (SHS) of light by laminar ferroelectric domains of the orthorhombic phase of RbH₂PO₄ below T_c=147 K is studied in detail. CCD images of the far-field SHS pattern reveal up to six off-axis distinct intensity maxima in a plane normal to the ferroelectric axis c. These scattering maxima are interpreted on the basis of the quasi-phase matching (QPM) conditions for the three sets of polarizations allowed by the nonvanishing elements of the second-order nonlinear susceptibility tensor. On this assumption scattering angles of the three SHS modes calculated from crystal optics are shown to fit well the experimental data for any incidence of the pump beam normal to c. Scattering intensities of the two most intense modes are also measured versus the component of the wave vector perpendicular to the modulated structure. A stochastic model giving the intensity as a function of the density probability of domain widths is developed and is shown to give a good fit of the scattered intensity. Moreover, it permits the evaluation of the mean and dispersion of the ferroelectric domain widths, which are found to be, respectively, 2.6 and 0.7 μm in the crystal under study. This is consistent with the domain size of the ferroelastic counterpart revealed by polarization microscopy.     

钴掺杂二氧化锡纳米粉的光致发光和磁学性质

研究了钴掺杂对二氧化锡纳米粉的光致发光性质和磁学性质的影响,发现钴掺杂对发光带的位置影响很小,但紫外发光带与蓝色发光带的强度之比随掺杂含量的增加而下降.当钴掺杂含量达到0.02时,样品中的铁磁性被完全破坏.讨论了样品中的磁相互作用的机理,认为掺杂离子的不均匀分布、自旋极化子与掺杂离子之间的耦合都可能导致反铁磁性的相互作用,这种反铁磁性的作用破坏了铁磁性. 关键词： 钴掺杂二氧化锡 光致发光 磁学性质     

Ordered fluorite phases in the Bi2O3-Ta2O5 system: A structural and electrical investigation

Structure and electrical behaviour are reported for the system Bi_1-xTa_xO_1.5 + x (0.167 ≤ x ≤ 0.250). In the compositional range 0.200 < x ≤ 0.250 an incommensurately modulated pseudo-cubic phase (type II) is observed, with the appearance of a larger pseudo-cubic phase in the region 0.167 ≤ x ≤ 0.200. Structural analysis of the type II phases by neutron diffraction reveals subtle changes in the oxide ion distribution with temperature, associated with changes in the incommensurate modulation parameter. Analysis of the defect structure of the type II phase reveals chains of tantalate octahedra as a likely structural motif. It is proposed that these chains facilitate an electronic contribution to total conductivity at low temperatures through electron hopping along the chains. Changes in oxide ion vacancy ordering may explain the observed non-linear behaviour in the thermal expansion of lattice parameter and Arrhenius plots of total conductivity.     

CoFe2O4纳米颗粒的结构、磁性以及离子迁移

聚乙烯醇(PVA)溶胶凝胶法制备出CoFe₂O₄纳米微粉，用X射线衍射研究了铁氧体纳米颗粒的结构.测量了CoFe₂O₄纳米颗粒80—873 K的变温穆斯堡尔谱，发现纳米颗粒的磁转变温度范围为793—813 K，比块体材料的磁性转变温度要低.CoFe₂O₄纳米颗粒的德拜温度θ_A=674 K，θ_B=243 K，比块体材料要小.CoFe₂O₄纳米颗粒超精细场H_f随温度的变化符合T^3/2+T^5/2定理.当温度较高时，平均同质异能移IS随温度的升高而减小，并呈线性关系. 关键词： 纳米颗粒 磁性 穆斯堡尔谱     

Nax/2Bi1−x/2MoxV1−xO4 and Bi1−x/3MoxV1−xO4 New Scheelite-related phases

New Scheelite-related solid solutions of the compositions Na_x/2Bi_1−x/2Mo_xV_1−xO₄ (0≤x≤1) and Bi_1−x/3 Mo_xV_1−xO₄(0≤x≤0.2) have been synthesised by the substitution of Na and Mo at the A and B sites respectively of the ABO₄ type ferroelastic BiVO₄. The phases were characterised using chemical analysis, powder X-ray diffraction, scanning electron microscopy, EDAX, and Raman spectroscopy. While almost a continuous solid solution is obtained for the series Na_x/2Bi_1−x/2Mo_xV_1−xO₄, the absence of Na at the A-site results only in a narrow stability region for the other series, Bi_1−x/3 Mo_xV_1−xO₄ where 0≤x≤0.2. Raman spectra of selected samples at room temperature also suggest that vanadium and molybdenum atoms are disordered at the tetrahedral sites.