Determination of radium isotopes in soil samples by alpha-spectrometry

A sensitive and accurate method for determination of radium isotopes in soil samples by α-spectrometry has been developed ²²⁵Ra, which is in equilibrium with its mother ²²⁹Th, was used as a yield tracer. Radium in soil samples was fused together with Na₂CO₃ and Na₂O₂ at 600 °C, leached with HNO₃, HCl and HF, preconcentrated by coprecipitation with BaSO₄, separated from uranium, thorium and iron using a Microthene-TOPO chromatographic column, isolated from barium in a cation-exchange resin column using 0.05M 1,2-cyclohexylene-dinitrilo-tetraacetic acid monohydrate as an eluant, electrodeposited on a stainless steel disc, and counted by α-spectrometry. The detection limit of the method is 0.43 Bq·kg⁻¹ for ²²⁶Ra, ²²⁸Ra and ²²⁴Ra if 0.50 g of soil sample are analyzed. The method was checked with two certified reference materials supplied by the IAEA, and reliable results were obtained Fourteen soil samples collected from the refractory industry in Italy were also analyzed. The mean radiochemical yields for radium were 85.7±4.3%, and the obtained radium concentrations in the soil samples were in the range of 8.08–3878 Bq·kg⁻¹ for ²²⁶Ra, of 1.60–678 Bq·kg⁻¹ for ²²⁸Ra and 1.25–550 Bq·kg⁻¹ for ²²⁴Ra, with ²²⁸Ra/²²⁶Ra and ²²⁴Ra/²²⁶Ra ratios ranged from 0.159–0.821 and from 0.142 to 0.525, respectively.     

Determination of uranium isotopes in environmental samples by alpha-spectrometry

A new and accurate method for the determination of uranium isotopes (²³⁸U, ²³⁴U and ²³⁵U) in environmental samples by alpha-spectrometry has been developed. Uranium is preconcentrated from filtered water samples by coprecipitation with iron(III) hydroxide at pH 9-10 using an ammonia solution and the precipitate is dissolved in HNO₃ and mineralized with H₂O₂ and HF; uranium in biological samples is ashed at 600 °C, leached with Na₂CO₃ solution and mineralised with HNO₃, HF and H₂O₂; uranium in soil samples is fused with Na₂CO₃ and Na₂O₂ at 600 °C and leached with HCl, HNO₃ and HF. The mineralized or leaching solution in 2M HNO₃ is passed through a Microthene-TOPO (tri-octyl-phosphine oxide) column; after washing, uranium is directly eluted into a cell with ammonium oxalate solution, electrodeposited on a stainless steel disk and measured by alpha-spectrometry. The lower limits of detection of the method is 0.37 Bq^.kg^-1 (soil) and 0.22 mBq^.l^-1 (water) for ²³⁸U and ²³⁴U and 0.038 Bq^.kg^-1 (soil) and 0.022 mBq^.l^-1 (water) for ²³⁵U if 0.5 g of soil and 1 litre of water are analyzed. Five reference materials supplied by the IAEA have been analyzed and reliable results are obtained. Sample analyses show that, the ²³⁸U, ²³⁴U and ²³⁵U concentrations are in the ranges of 0.30-103, 0.49-135 and 0.02-4.82 mBq^.l^-1 in waters, of 1.01-7.14, 0.85-7.69 and 0.04-0.32 Bq^.kg^-1 in mosses and lichens, and of 25.6-53.1, 26.4-53.8 and 1.18-2.48 Bq^.kg^-1 in sediments. The average uranium yields for waters, mosses, lichens and sediments are 74.5±9.0%, 80.5±8.3%, 77.8±4.9% and 89.4±9.7%, respectively.     

An improved method for the determination of uranium isotopes in environmental samples by alpha-spectrometry

In order to improve the selectivity of the uranium isotopes determination in environmental samples, further studies have been carried out, including (1) interference of ²¹⁰Po with uranium isotope determination, (2) distribution coefficients of polonium between 5% TOPO in toluene and aqueous hydrochloric and nitric acids, (3) decontamination factor of uranium from polonium of the recommended procedure, and (4) leaching effect comparison of two different leaching procedures in a lichen sample. Based on the new findings, a more accurate extraction chromatographic/ a-spectroscopy method has been developed. For the method's validation, four kinds of reference materials supplied by the IAEA have been tested. It is observed that nearly all the ²³⁸U, ²³⁴U and ²³⁵U concentrations obtained are in good agreement with the recommended or information values, showing that the method can give reliable results. A comparison with existing uranium determination methods has also been made. It is concluded that due to involving preconcentration and chemical separation, the extraction chromatographic/a-spectroscopy method is a more selective, very sensitive and accurate, and low cost method. This revised version was published online in July 2006 with corrections to the Cover Date.     

Determination of uranium isotopes in environmental samples

The determination of isotopes of uranium by alpha spectrometry in different environmental components (sediments, soil, water, plants and phosphogypsum) is presented and discussed in this paper. The alpha spectrometry is a very convenient and good technique for activity concentration of natural uranium isotopes (²³⁴U, ²³⁵U, ²³⁸U) in environmental samples and provides the most accurate determination of isotopic activity ratios between ²³⁴U and ²³⁸U. The analysis were provided information about possible sources of high concentrations of uranium in the examined sites determined by anthropogenic sources. The calculation of values ²³⁴U/²³⁸U in all analyzed samples was applied to identifying natural or anthropogenic uranium origin. Activity concentration of uranium isotopes in analyzed environmental samples shows that measurement of uranium levels is of great importance for environmental and safety assessment especially in contaminated areas (phosphogypsum waste heap).     

Implementation of alpha-spectrometry for uranium isotopes in excreta samples

Summary The measurement of radioactivity concentrations in excreta is an important tool for the monitoring of possible radionuclide intakes by occupationally exposed workers. For this purpose, a radiochemical procedure for the determination of alpha-emitting isotopes of uranium in excreta has been optimized. The main steps involved in this procedure are pre-concentration, dissolution of sample, separation by ion-exchange resin, electrodeposition and alpha-spectroscopy. ²³²U tracer is used to monitor chemical recoveries and correct the results to improve precision and accuracy. The quality control of radiochemical analysis in urine and faecal samples has been performed with participation in intercomparison exercises. The results obtained from these samples, with chemical recoveries (80-95%), are shown to be highly consistent. The method offers good prospects to be applied in routine monitoring programme of workers.     

Determination of thorium isotopes in gas lantern mantles by alpha-spectrometry

A procedure for the determination of the three main isotopes of thorium in gas lantern mantles by alpha-spectrometry has been developed. The samples examined were dissolved in concentrated nitric acid and thorium was precipitated as hydroxide. Thorium was then dissolved in hydrochloric acid to be extracted into a TOPO solution, back-extracted with sulfuric acid, electrodeposited onto a steel disc and finally counted alpha-spectrometrically. The radiochemical recovery for thorium was 94% with a counting efficiency of 37%.     

Determination of alpha-emitting Pu isotopes in environmental samples

This paper presents an improved radiochemical procedure for the determination of alpha-emitting Pu isotopes in environmental samples (soils, sediments, vegetation) by alpha-particle spectrometry. Quantitative Pu recovery yields were obtained (average 60%), 0.1 mBq being the average minimum detectable activity by the complete technique. Special efforts were made to ensure the removal of traces of different natural alpha-emitting radionuclides, which can interfere with the correct determination of 239+240Pu and 238Pu concentrations. The radiochemical procedure was validated by application to reference material and by participation in intercomparison exercises. This radiochemical procedure was applied to the different layers of a high-resolution sediment core taken from a lake in Sweden. The 239+240Pu and 238Pu/239+240Pu profiles obtained in the high-resolution sediment core correctly reproduced the expected evolution of these quantities as observed historically in the atmosphere, validating the procedure for this purpose and showing the power of these radionuclides for dating purposes.     

On the determination of radium by alpha-spectrometry

In order to determine radium in environmental samples by -spectrometry, the way in which some changes in the chromatographic conditions can affect the purification of the element on cation exchange columns from hydrochloric solutions have been studied. Some modifications have also been introduced in the method of electrodeposition of radium from an ammonium oxalate electrolyte.     

Radioactive radium and lead isotopes determinations in biota samples

²¹⁰Pb and radium’s isotopes were determined in biota samples by two different radiochemical techniques—Fe(OH)₃ co-precipitation and calcium phosphate precipitation. The applied procedures were adapted for very small amount (0.25 g) of sample material and were checked in actual biota samples. Measurements were made by liquid scintillation counting, α- and γ-spectrometry. All the results show that Ca₃(PO₄)₂ precipitation technique is better for determination of trace radionuclide concentrations in biota. The procedure of separation is stable with significant yield for the both ²¹⁰Pb and radium’s isotopes and can be successfully used for assessment of environmental stressors in field of bio-monitoring.     

Determination of alpha-emitting uranium isotopes in soft tissues by solvent extraction and alpha-spectrometry

A radiochemical procedure has been developed for the determination of alpha-emitting isotopes of uranium ((238)U, (235)U and (234)U) in soft tissues. Known amounts of sample are spiked with (232)U internal tracer and wet-ashed. Uranium is co-precipitated with iron hydroxide as carrier, and extracted into 20% trilaurylamine solution in xylene after dissolution of the precipitate in 10M hydrochloric acid. The uranium, after stripping into an aqueous phase, is electro-deposited onto a platinum disc and counted by alpha-spectrometry. The radiochemical recovery ranges from 60 to 85% for bovine liver samples. The average radiochemical recoveries for human tissues vary from 53 to 78%.     

Liquid-liquid extraction separation and sequential determination of plutonium and americium in environmental samples by alpha-spectrometry

A procedure is described by which plutonium and americium can be determined in environmental samples. The sample is leached with nitric acid and hydrogen peroxide, and the two elements are co-precipitated with ferric hydroxide and calcium oxalate. The calcium oxalate is incinerated at 450 degrees and the ash is dissolved in nitric acid. Plutonium is extracted with tri-n-octylamine solution in xylene from 4M nitric acid and stripped with ammonium iodide/hydrochloric acid. Americium is extracted with thenoyltrifluoroacetone solution in xylene at pH 4 together with rare-earth elements and stripped with 1M nitric acid. Americium and the rare-earth elements thus separated are sorbed on Dowex 1 x 4 resin from 1M nitric acid in 93% methanol, the rare-earth elements are eluted with 0.1M hydrochloric acid/0.5M ammonium thiocyanate/80% methanol and the americium is finally eluted with 1.5M hydrochloric acid in 86% methanol. Plutonium and americium in each fraction are electro-deposited and determined by alpha-spectrometry. Overall average recoveries are 81% for plutonium and 59% for americium.     

Determination of isotopic thorium in biological samples by combined alpha-spectrometry and neutron activation analysis

The determination of isotopic thorium by alpha-spectrometric methods is a routine practice for bioassay and environmental measurement programs. Alpha-spectrometry has excellent detection limits (by mass) for all isotopes of thorium except²³²Th due to its extremely long half-life. This paper reports a pre-concentration neutron activation analysis (PCNAA) method for²³²Th that may be performed following alpha-spectrometry if a suitable source preparation material is utilized. Human tissues and other samples were spiked with²²⁹Th and the thorium was isolated from the sample using ion exchange chromatography. The thorium was then electrodeposited from a sulfate-based medium onto a vanadium planchet, counted by alpha-spectrometry, and then analyzed for²³²Th by neutron activation analysis. The radiochemical yield was determined from the alpha-spectrometric method. Detection limits for²³²Th by this PCNAA method are approximately 50 times lower than achieved by alphaspectrometry.     

Determination of aniline in environmental water samples by alternating-current oscillopolarographic titration

A new method for the determination of aniline in environmental water based on oscillopolarographic titration was presented in this paper. Several factors including the kind, concentration, and volume of acid, the dosage of potassium bromide, the temperature and concentration of concomitant substances were investigated in detail. The experimental results indicated that this method was simple, rapid, and sensitive. The linear range was 8.367×10-4 to 2.789×10-2 mol L-1, the relative standard deviation (R.S.D.) was lower than 0.96%, and the spiked recoveries of aniline in environmental water samples were in the range of 99.4-106.9% under the optimal conditions. The results indicated that the present method could be used as an alternative method for aniline determination in realworld water samples.     

Determination of explosives in environmental water samples by solid-phase microextraction-liquid chromatography

When explosives are present in natural aqueous media, their concentration is usually limited to trace levels. A preconcentration step able to remove matrix interferences and to enhance sensitivity is therefore necessary. In the present study, we evaluated solid-phase microextraction (SPME) technique for the recovery of nine explosives from aqueous samples using high-performance liquid chromatography with ultraviolet detection (HPLC-UV). Several parameters, including adsorption and desorption time, coating type, rate of stirring, salt addition, and pH, were optimized to obtain reproducible data with good accuracy. Carbowax coating was the only adsorbent found capable of adsorbing all explosives including nitramines. Method detection limits (MDL) were found to range from 1 to 10 microg/L, depending on the analyte. SPME/HPLC-UV coupling was then applied to the analysis of natural ocean and groundwater samples and compared to conventional solid-phase extraction (SPE/HPLC-UV). Excellent agreement was observed between both techniques, but with an analysis time around five times shorter, SPME/HPLC-UV was considered to be applicable for quantitative analysis of explosives.     

毛细管电泳定量检测环境水样中无机阴离子

详细讨论了胶束浓度、间接吸收背景物质的浓度及有机添加剂组成等对部分卤素及其含氧酸根的毛细管电泳分离影响;在优化的条件下,3.5min内高效、快速地完成了Cl-、Br-、ClO3-、BrO3-四种无机阴离子的分离分析,分离的理论塔板数在1.6×106～2.8×105/m之间,检出限在11.2～23.3mg/L之间,迁移时间的相对标准偏差小于1%,峰面积的相对标准偏差在5.2%～2.2%之间;并将方法用于环境水样的分析。     

Determination of boron in glass by alpha-spectrometry

Alpha-spectrometric method has been used for the determination of boron in borosilicate glasses. For irradiation thermal neutrons with a flux of about 10⁵ n·cm^–2·s^–1, produced in a paraffin moderator surrounding a deuteron target of a small neutron generator, were used. Alpha-particles from the reaction¹⁰B(n, ) were detected by a Si solid state detector with a resolution of about 50 keV. The sensitivity of the method is 0.05 wt % boron in glass samples.This work was supported by the Hungarian Research Foundation (Contract No. 1734/91.).     

Determination and interpretation of environmental water samples contaminated by uranium mining activities

Interpretation of environmental behavior of uranium is based on several steps of data analysis and statistical inference. First step is sampling and analyzing of uranium in field samples by routine laboratory methods. Such methods have to fulfill multiple requirements like robustness, efficiency, low detection limit and precision. A comparison of different approaches in assigning uncertainty to experimentally obtained analytical data shows that classical error estimation is not significantly inferior to more sophisticated modern techniques like inverse regression or orthogonal regression. A second step is the correlation of analytical data with current state of insight into environmental behavior of uranium. Such a correlation furthers the choice of adequate geochemical models and quality of geochemical data base for subsequent detailed analysis, e.g. by geochemical modeling. An appraisal of the individual steps in this complex analysis is given on the basis of statistical procedures for calibration and an E_H-pH diagram of uranium for atmospheric conditions.     

Determination and interpretation of environmental water samples contaminated by uranium mining activities

Interpretation of environmental behavior of uranium is based on several steps of data analysis and statistical inference. First step is sampling and analyzing of uranium in field samples by routine laboratory methods. Such methods have to fulfill multiple requirements like robustness, efficiency, low detection limit and precision. A comparison of different approaches in assigning uncertainty to experimentally obtained analytical data shows that classical error estimation is not significantly inferior to more sophisticated modern techniques like inverse regression or orthogonal regression. A second step is the correlation of analytical data with current state of insight into environmental behavior of uranium. Such a correlation furthers the choice of adequate geochemical models and quality of geochemical data base for subsequent detailed analysis, e.g. by geochemical modeling. An appraisal of the individual steps in this complex analysis is given on the basis of statistical procedures for calibration and an E_H-pH diagram of uranium for atmospheric conditions. Received: 30 July 1998 / Revised: 18 November 1998 / Accepted: 26 November 1998