高比表面积有序介孔氧化铝的制备与表征

采用溶胶-凝胶法以非离子表面活性剂PEO-PPO-PEO三嵌段共聚物F127为模板剂, 以异丙醇铝为铝源, 以异丙醇为溶剂, 成功地制备出比表面积为485 m2/g、孔径分布窄(2~20 nm)、孔容在1.2 cm3/g以上和孔道呈蠕虫状且具有一定有序性的介孔氧化铝. 采用BET, TEM, XRD和TG多种测试技术对产物性能进行了表征. 探讨了水铝比、醇水混合溶液的滴加速度、反应时间、水浴温度、陈化温度及陈化时间等条件对合成的有序介孔氧化铝结构的影响.     

负载Cu氧化铝纳米管合成及在NO+CH4反应中催化性能研究

采用过氧化氢调节反应条件,在水热体系中合成了新型的勃姆石纳米管,经520℃焙烧2h后,晶型由AlOOH转化为γ-Al2O3;采用XRD、氮吸附、TEM等对合成的纳米管进行表征.结果表明,合成的γ-Al2O3纳米管长约300nm,外径20nm,比表面积达到230m2/g以上.以此为载体,采用等体积浸渍法用Cu(NO3)2...     

几种方法制备的H3PW12O40/SiO2催化剂的结构和催化性能

 针对H3PW12O40(HPW)的比表面积小和不易回收利用等缺点,分别采用浸渍法、溶胶-凝胶法和以离子液体为模板剂的溶胶-凝胶法制备了HPW/SiO2催化剂,采用傅里叶变换红外光谱、 X射线衍射、 N2物理吸附和吸附氨的程序升温脱附等技术对催化剂样品进行了表征,并考察了其对苯硝化反应的催化性能. 结果表明,所制备的催化剂样品都保持了HPW原有的Keggin结构. 浸渍法制备的催化剂的比表面积(475.2 m2/g)较小,使用4次后硝基苯的收率由82.4%下降到70.7%; 溶胶-凝胶法制备的催化剂的比表面积(498.6 m2/g)居中,使用4次后硝基苯的收率由85.1%下降到79.6%; 以［emim］BF4离子液体为模板剂,采用溶胶-凝胶法制备的催化剂含有介孔结构,比表面积(558.5 m2/g)最高,使用4次后硝基苯的收率由84.7%下降到79.9%. 不同方法制备的HPW/SiO2催化剂具有较高的催化苯硝化反应活性和较好的稳定性.     

高热稳定性、 高比表面积低铈型铈锆钇储氧材料的制备及其性能研究

采用氨水 碳酸铵混合沉淀剂制备了低铈型铈锆钇三组分储氧材料. 采用X射线衍射、 BET、 氧脉冲吸附和H2程序升温还原(H2-TPR)等技术对材料的晶体结构、 比表面积、 孔结构、 储氧性能和还原性能进行了研究. 结果表明， 该材料经873 K焙烧4 h后比表面积达到116.8 m2/g, 孔容达到0.30 cm3/g, 经1 273 K老化10 h后, 比表面积和孔容仍然保持在68.1 m2/g和 0.22 cm3/g. 由XRD结果可知, 材料的物相组成为四方相的Zr0.84 Ce0.16 O2, 在热处理过程中物相结构稳定. 氧脉冲吸附和程序升温还原的结果表明, 材料储氧性能保持较好.     

修饰晶种法合成MFI型分子筛膜包覆的活性炭颗粒

由于分子筛膜的分离和催化作用, 分子筛膜包覆的传统催化剂颗粒可以实现高效的催化过程. 活性炭颗粒作为一种常用的催化剂载体, 由于其表面的憎水性和不平整, 在不规则活性炭颗粒表面直接水热合成包覆一层分子筛膜非常困难. 为了克服上述缺点, 本文采用一种勃姆石凝胶修饰的晶种法在活性炭颗粒表面合成连续的分子筛膜. 以勃姆石溶胶为前驱体, 在活性炭颗粒表面通过喷涂预先形成一层相对平整的勃姆石凝胶层以改善活性炭表面. 在随后的晶种涂覆过程中, 晶种分散液加入部分勃姆石溶胶为胶粘剂, 所得的晶种层覆盖载体完全, 与载体结合牢固, 无需焙烧处理. 将晶种涂覆后颗粒在旋转动态水热175℃处理6 h, 得到分子筛膜包覆的活性炭颗粒, 所得材料分别用X射线衍射和扫描电镜进行表征. 包覆的分子筛膜为MFI 结构, 厚度约为5μm. 对比实验表明, 没有勃姆石溶胶修饰的活性炭颗粒上不能成膜. 这种勃姆石凝胶修饰晶种法为在各种惰性载体上合成分子筛膜提供了便捷的方法.     

低密度、块状氧化铝气凝胶制备

研究了工艺参数对氧化铝溶胶及气凝胶的影响。结果表明,稳定的氧化铝溶胶优化制备工艺为：仲丁醇铝为前驱体,水解温度60 ℃,仲丁醇铝、乙醇、水的物质的量之比为1∶(8～16)∶1.2;螯合剂乙酰乙酸乙酯能有效控制仲丁醇铝水解缩聚速率,提高溶胶的稳定性;块状氧化铝气凝胶主要成份为多晶勃姆石相,比表面积为447 m²·g^-1,其强度和密度随乙醇量的增加而降低,密度最低为0.040 g·cm^-3。氧化铝气凝胶微观结构由许多片叶状颗粒堆积形成,经1 200 ℃热处理后仍保持原有的微观形貌,比表面积为73 m²·g^-1。     

凝胶法制备条件对载体硅胶孔结构的影响

以水玻璃、硫酸为原料采用凝胶法制备了烯烃环氧化催化剂载体硅胶,为探讨制备条件对硅胶孔结构的影响,采用物理吸附仪对不同条件下制备的硅胶进行了表征,结果表明:溶胶pH值、老化温度和老化时间、氨水pH值对硅胶孔结构影响显著,当溶胶pH值为1.5,在80℃下用pH 10.5的氨水浸泡老化凝胶2 h,所得硅胶的比表面积在300 m2.g-1左右,孔径和孔容分别在9.71 nm和0.92 cm3.g-1以上,以此硅胶为载体制得的非均相催化剂Ti/SiO2对于氯丙烯和环己基过氧化氢的环氧化反应具有明显的催化活性。     

勃姆石纤维增强二氧化硅气凝胶的制备及性能

以六水合氯化铝为铝源, 通过水热法制备勃姆石纤维; 以甲基三甲氧基硅烷和正硅酸乙酯为硅源共前驱体, 采用溶胶-凝胶法进而常压干燥制备了勃姆石纤维掺杂的二氧化硅复合气凝胶; 探究了勃姆石纤维的掺杂量对复合气凝胶性能的影响. 当勃姆石纤维的掺杂量(质量分数)为1%时, 气凝胶的机械性能最好, 能够承受17.1%的压缩应变, 最大压缩强度为1.12 MPa, 压缩模量高达2.57 MPa, 复合气凝胶在150 ℃仍然具有较低的导热系数(0.0670 W·m^?1·K^?1). 勃姆石纤维能够一定程度地抑制二氧化硅颗粒在高温下的烧结和相转变, 对二氧化硅气凝胶的耐高温性能有显著的提升作用, 复合气凝胶在1100 ℃高温热处理后, 仍能保持良好的隔热性能和较高的机械强度.     

超临界干燥法制备TiO2气凝胶

以钛酸四丁酯为原料,采用溶胶-凝胶过程及及超临界干燥法制备了TiO2气凝胶,并通过XRD,BET和TEM等方法对所得样品进行了表征.结果表明,该法制备的TiO2气凝胶具有很高的比表面积(488 m2/g),平均粒径为4.6nm,具有锐钛矿型晶体结构.经400℃煅烧2 h所得的纳米粉体,其锐钛矿型晶体结构更为明显,平均粒径6.7 nm,比表面积158 m2/g.     

喷雾-胶凝法制备超细莫来石粉末

以水玻璃和硝酸铝为原料 ,通过喷雾 -胶凝法和共沸蒸馏技术制备莫来石前驱粉体 ,然后煅烧得到超细莫来石粉末 .用TG -DTA、XRD、TEM及BET研究了莫来石前驱粉体在煅烧过程中的热学性质、物相与比表面变化及颗粒大小与形貌变化 ,并对所制得的莫来石粉进行了表征 .结果表明 ,莫来石前驱粉体经 130 0℃煅烧 1h可制得粒径为 2 5nm～ 4 0nm ,比表面积为 4 2 5m2 /g的莫来石超细粉 ;煅烧过程中的物相变化次序为 :勃姆石 +非晶态SiO2 →非晶态Al2 O3 +非晶态SiO2 →γ -Al2 O3 +非晶态SiO2 → 3Al2 O3 ·2SiO2 .     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.