Speciation of heavy metals in sediments of the lagoon of Venice collected in the industrial area

In this study a procedure of sequential extraction of metals from sediments was applied to samples from the lagoon of Venice. Compared to the measurement of total concentrations, the knowledge of metal partitioning among sediment phases can help in estimating the risk posed by metal polluted sediments and give information on contamination sources and on the factors that influence metal enrichment in sediments. The results permitted to estimate for each metal the percentage of the total content that could be potentially remobilized from sediments, owing to changes in environmental conditions. The immediately available fraction represented in general a low proportion of the total content. An important proportion of most metals (except for Zn, Cd and Cu) was associated to residual phases and therefore was not expected to be released under the normal environmental conditions. The large amounts of metals bound to Fe-Mn oxides/hydroxides confirmed the strong scavenging efficiency of this phase. The carbonate phase was the preferential associative form for Pb, Cd and Zn, whereas Cu was bound in prevalence to the organic matter/sulphide phase.     

连续萃取法研究海湾养殖区沉积物中重金属形态

以连续萃取法研究海湾养殖区沉积物中重金属(Cd, Cu, Pb, Zn)的形态,将重金属分离为酸溶态、还原态、有机质结合态、硫化物结合态和残渣态.分别采用基体匹配法和内标法消除高盐基体对电感耦合等离子体光谱法(ICP-OES)和质谱法(ICP-MS)分析结果的影响.对海洋沉积物标准物质分析结果表明,样品稀释后测定值与标准值一致.比较了本连续萃取法和BCR法对沉积物样品中重金属形态的提取结果,并考察了萃取剂的选择性.实验表明,本方法可用于有机质污染和富营养化环境沉积物中重金属形态分析,特别是有机质结合态和硫化物结合态的分析.     

Some peculiarities of metal migration in the aerobic and anaerobic conditions in the surface water bodies

The results of research on metal migration (Mn, Cu, Zn, Pb, Cr) in the surface water bodies of the different type (the Kiev and the Kanev reservoirs of the Dnieper cascade, and Verbnoye and Telbin lakes of the Kiev city) in dependence on their oxygenous regime are considered. It was shown that the metal migration in the aerobic conditions is mainly directed from water thickness to bottom sediments. In contrast, the migration of metal compounds from bottom sediments in the anaerobic conditions is increased. Manganese is mostly in a form of free ions Mn²⁺ in the pore solutions, therefore, it migrates from bottom sediments in the greatest extent. The migration of other studied metals occurs in a much smaller extent and depends on the migration mobility of organic substances which they are bound to complexes. Migration mobility of copper, lead and chromium decreases essentially when the hydrogen sulphide is in the water of bottom layer. The data on a degree of metal binding to complexes and their chemical nature in water of reservoirs and lakes are given. The greater part of metals is found to be in complex compounds with humic substances in water of the Dnieper reservoirs, whereas in the lakes a share of neutral (mainly with carbohydrates) and cationic (mainly with protein-like substances) complexes essentially increases. The distribution of metals is explained by distinction in a component composition of dissolved organic matters in the reservoirs and in the lakes.     

Study of the Contents and Speciation of Heavy Metals in River sediments By Factor Analysis

Abstract

Heavy metals Zn, Cd, Pb, Cu, Ni and Co from two spanish river sediments have been determined by voltammetric techniques, along with % CaCO₃ and % organic matter, and the whole data set examined by means of Factor Analysis, finding a different behaviour of the metals in each river.

Heavy metal speciation in the sediments was carried out by using the Tessier's scheme: Zn and Pb were mainly associated to ‘reducible phases’, Cd and Cu bound to ‘organic matter and sulphides’, and Ni and Co were distributed between the above fractions. The ‘residual’ metals were used as pollution indicators from the rivers, finding a similar behaviour to other industrialized river systems.     

氧化与还原条件下伊通河长春区段沉积物重金属形态特征的对比研究

利用改进的Tessier连续萃取法研究了伊通河长春市自由大桥处不同深度沉积物样品在氧化及还原条件下Cu,Pb,Zn和Ni的形态变化规律,同时分析了沉积物样品中酸可挥发性硫(Acid volatile sulfide,AVS)和同时提取重金属(Simultaneous extract metals,SEM)的含量. 实验结果表明，样品经干燥、研磨处理后,Cu有机/硫化物结合态比例减少40%,锰氧化物结合态的比例显著增加; Pb,Zn和Ni 3种元素有机/硫化物结合态比例均略有下降,变化幅度小于Cu,并重新分配到不同的化学相中. 通过SEM中各金属含量与有机/硫化物结合态中金属含量的对比可知,还原性沉积物中Cu除了与硫化物结合外,很大一部分是以有机物形态存在的,Pb,Zn,Ni,Fe和Mn则主要以硫化物形态存在,各元素形态分析均不同程度地受到萃取剂的影响.     

Assessment of heavy metals leachability from metallo-organic sorbent-iron humate-with the aid of sequential extraction test

The sequential extraction test, known as a BCR procedure, was used to assess a leachability of heavy metals (Zn, Cd, Pb, Cu) from the metallo-organic sorbent—iron humate—loaded with these metals. The sequential test allowed to discriminate between various fractions of heavy metals, namely the acid-extractable fraction, the fraction bound to Fe oxides, and the fraction bound to organic matter. It was proven that the heavy metals are bound mainly to Fe oxides and organic matter, and thus they may be relatively hardly liberated into the environment. The BCR sequential extraction test exhibited a very good repeatability, when it was applied to the loaded sorbent—relative standard deviations were typically lower than 10%.     

Heavy metals in marine sediments from the Mar Piccolo of Taranto (Ionian Sea, southern Italy)

Heavy metals concentrations (Cd, Cu, Hg, Pb, Sn and Zn) have been determined monthly in surface sediments from the Mar Piccolo in Taranto (Ionian Sea, Southern Italy. a semi-enclosed marine basin very important from a mussel-culture point of view. In sediments, sulphides, percentage of organic carbon and redox potential were also determined to show possible correlations between metals levels and redox characteristics of marine sediments. Analytical results, elaborated by multivariate statistical techniques, confirm that sediments collected in the first inlet of Mar Piccolo, where shipbuilding activities are present, have a contamination level greater than those collected in the second inlet. For each metal, the geoaccumulation index (Igeo) has been calculated as criterion to evaluate both pollution levels and metals enrichment in examined sediments: Igeo values confirm that the first inlet is an moderately polluted area from Hg and Pb. In any case, high sulphide concentrations and negative values of redox potentials bring to a conclusion that metals are present in sediments, mainly as insoluble sulphides and then as not bioavailable compounds for filter feeders organisms such as mussels.     

Distribution and speciation of metals in surface sediments of Taranto [corrected] gulf (Ionian Sea, Southern Italy)

Concentrations of metals (Al, Fe, Ti, Ni, Mn, Cr, Zn, Cu, Pb) were determined in surface sediments from Taranto gulf (Ionian Sea, Southern Italy) in order to assess the distribution and the bioavailability of metals. Total metal content and speciation of Fe, Ni, Mn, Zn, Cu and Pb were determined. Sediment cores were also sampled in some stations of particular interest. The analytical results show that metals distribution does not show significant variations in relation to depth. Metal distribution in the Taranto gulf is mainly influenced by industrial wastes from Taranto town, by rivers of the Basilicata region and by prevailing anticlockwise marine currents. These factors cause an accumulation of metals in the sediments near to the coasts of Calabria. The statistical analysis, effected by HCA and PCA methods, can be considered a good starting point in order to classify sediment samples and to locate accumulation areas. Metal speciation shows that Fe, Ni and Zn are present in sediments mainly as sulphides, Mn is present principally in an ion-exchange form or bound to carbonate, while Cu and Pb are mainly present in the fraction bounds to humic acids.     

Comparison of metal analysis in sediments using EDXRF and ICP-OES with the HCl and Tessie extraction methods

The work presents an investigation on metal availability in sediments during 13 months using the dispersive-energy X-ray fluorescence (EDXRF) and atomic emission spectrometry with induced argon plasma (ICP-OES) techniques and single extraction (0.1 mol l⁻¹ HCl) and Tessie’s sequential speciation methods. The EDXRF technique could yield essentially the same profile as ICP-OES for the seasonal variation of metals in sediments, but in a more practical way. The sequential extraction procedure (SEP) was more efficient in metal dissolution than single extraction. The Pb, Ni, Al, Cr, and Fe elements were less efficiently extracted with single extraction in relation to sequential extraction. For Co both methodologies were equivalent, but for Cu and Mn the extraction was higher with single extraction. Single extraction does not mobilize Pb, Ni, Al, Cr, and Fe adsorbed on oxides and bound to organic matter. However for Cu and Mn, not only extracted these metals from the four fractions, but it also dissolved part of the fifth fraction (residual). Principal Component Analysis discriminated seasonal variations in the content of several metals, mainly Fe, Co, Ni, and Zn. The mobility of metallic ions in the sediments is conditioned to the seasonal flow of organic and inorganic material coming from the river or by the erosion of adjacent soils.     

煎煮对几种特色南药中重金属元素含量和形态影响

考察了几种特色南药中重金属(Cd,Cr,Cu,Fe,Mn,Ni,Pb,Sr,Zn)的含量状况,并采用形态连续萃取法分析重金属在药材中的形态分布,研究了药材煎煮时药材中重金属的释放及煎煮过程对药材中重金属形态分布的影响。结果表明,几种南药中Cr,Pb,Zn的含量较高,且巴戟天中的重金属总量高于限量标准;原药材中Cr,Cu,Mn,Ni,Pb和Zn主要存在于有机态和残留态,Fe和Sr主要存在于残留态。煎煮使南药中大量重金属迁移到药汤中;药汤中Cu,Mn,Cr,Pb和Zn主要来自于其在药材中的可交换态、碳酸盐结合态和有机态,而药汤中Sr,Ni和Fe不仅包含其非残留态,更多来自于它们的残留态。为减少药汤中重金属,对于Cu,Mn,Cr,Pb和Zn既要控制在药材中的总量,且需降低它们在药材中的非残留态含量;对于Fe,Ni和Sr则主要是控制其在药材中的总量。     

象山港海底沉积物中重金属的赋存形态

以象山港海底沉积物为研究对象,采用了五步连续萃取法对象山港区域表层沉积物中重金属(Fe、Mn、Cu、Zn)赋存形态进行了研究,分析了各形态重金属在象山港不同采样点中的分布特征和影响因素.结果表明,象山港海域表层沉积物中各重金属元素主要来源于自然输入的残留态,人为输入的各种活性形态所占比例相对较少,但受两种因素的影响的差...     

Heavy metal in sediments and bioaccumulation in the bivalve Corbula gibba in a drilling discharge area

The longterm bioavailability of heavy metals in sediments of a Northern Adriatic Sea shelf area affected by drilling mud and cutting discharges was discussed. Levels of Mn, Cu, Cr, Zn and Pb in different geochemical phases of the sediment and in soft tissues of the bivalve Corbula gibba were recorded and the relationships between biological and geochemical metal investigated. Total metal content, acetic acid extractable-, exchangeable-, carbonate-, easily reducible-, moderately reducible-, oxidable- and residual-fractions were determined on sediment samples. Corbula gibba was collected from wet sediments at the same times and sites, and the soft-tissue metal contents were determined. Correlations show that the fractions with greatest bioavailability are the exchangeable and carbonate for Cr and the exchangeable, carbonate, easily and moderately reducible fractions for Zn. Data also show a possible bioavailability of Pb only from the residual fraction, consisting of very resistant matter of more recent anthropogenic origin. Near the platform, total Mn content in sediments and in C. gibba tissues show a strong correlation suggesting that this organism is sensitive to variations of the Mn-oxi-hydroxides superficial film. No relationships were found between biological and sediment-bound Cu, however the discharged muds did not cause Cu enrichment. The metal fraction determined by weak acetic acid extraction at no point seems related to metal levels in Corbula gibba.     

Combining multivariate analysis and geochemical approaches for assessing heavy metal level in sediments from Sudanese harbors along the Red Sea coast

Multivariate statistical analysis and geochemical approaches were exploited for the assessment of the level of some heavy metals (Mn, Fe, Ni, Cu, Zn and Pb) in sediments from Sudanese harbors along the Red Sea coast. Principal component analysis, as a multivariate statistical analysis approach, was applied to identify contribution sources by heavy metals in sediments. While a single source (crustal) was recorded in the bulk sediments and coarse sediment grains (grain-size 1000-500 µm), two sources (crustal and anthropogenic) were recorded in fine sediment grains (grain-size < 500 µm). Furthermore, enrichment factor (EF), as a geochemical approach, appointed polluted sites by heavy metals in the study area. Based upon a previous study addressed the interpretation of EF values, minor to moderate anthropogenic enrichment were recorded in sediments from some sites in the study area. The main anthropogenic activities that believed to be the major sources of pollution by heavy metals in the study area are discharges from oil refinery, industry, shipping activity and domestic waste. Hierarchical cluster analysis (HCA), as another multivariate statistical analysis approach, was applied for the concentrations of heavy metals in bulk sediments to group sediments according to their mineralogical composition. The output of HCA is that sediments from the Port-Sudan harbor can be divided mainly into three areas — east, west and south. For the Sawakin harbor, no apparent trend for the spatial distribution of heavy metals in sediments was recorded.     

Ecological risk assessment of sediment in wastewater discharging area by means of metal speciation

This study was designed to evaluate the influence of wastewater discharge to the marine ecosystem after treatment plant construction. Heavy metal concentrations in sediment and bioavailability of the metals were analyzed and ecological risks were assessed using the results. Metal speciation for sediments collected in the wastewater discharging area was measured by a Shimadzu AA-680 atomic absorption spectrometer. The distribution of the metals among various geochemical phases was determined. Biological samples collected and analyzed were four species of crustacea, four species of bivalve, and seven species of fish. Exchangeable fraction of superficial sediment (0–2 cm layer) was Zn 35.09%, Ph 5.30%, Cu 0.86%, Cr 0.01% and Fe 0%. However, exchangeable fraction of deep layer sediment (15–20 cm) was not detected for all metals analyzed. Deeper sediments were found to have more residual fraction, and bioavailable phases decreased by depth, which provides an indication of the seriousness of wastewater discharge effect in this enclosed bay. The chemical concentrations observed to be associated with biological effects were sorted. The comparisons were made with regard to the potential for adverse biological effects. The potential of adverse biological effects in the sediments of wastewater discharge site was estimated as Zn 69.8%, Pb 35.8%, Cu 29.1%, and Cr 21.1%, respectively. Mullet (Mugil cephalus) among biological samples had the highest concentration of Zn in the muscle and liver organs. The bioconcentration factors (BCFs) of Zn by the mullet, mussel, oyster and crab were the highest among heavy metals determined. This result was well related to 81.6% of bioavailable phase Zn and 69.8% of adverse biological effects for the surface sediment.     

Assessment of trace metals contamination in estuarine sediments using a sequential extraction technique and principal component analysis

Fractionation of the metals Cd, Cr, Cu, Ni, Pb and Zn in sediments was performed for samples collected from eight locations in the Poxim river estuary of Sergipe State, northeast Brazil, using the 3-stage sequential extraction procedure proposed by the European Community Bureau of Reference (BCR). The extraction method was found to be satisfactory for analysis of certified reference material BCR-701, with recovery values ranging from 85% (Cu) to 117% (Cr). The detection limits obtained were 0.001 to 0.305 µg g^− 1. Zn exhibited greatest mobility and bioavailability, indicative of anthropogenic sources, while Cr was mainly found in the residual fraction and could be used as an indicator for the contribution from natural sources. Cd, Cu, Ni and Pb were associated with the oxidizable fraction, and Pb, Cr and Ni with the reducible fraction. Principal component analysis (PCA) clearly separated the metals into three groups: I (Zn); II (Pb); III (Cd, Cu, Cr and Ni). These groupings were mainly due to different distributions of the metals in the various fractions, in sediments from the different locations. Risk assessment code (RAC) analysis indicated that although the metals presented a moderate overall risk to the aquatic environment, nickel showed a low risk (RAC < 10%) at three sites, while zinc presented a high risk (RAC > 30%) at four other sites.     

Comparison of three sequential extraction procedures used to study trace metal distribution in an acidic sandy soil

On an acid sandy soil contaminated with trace metals (Fe, Mn, Cu, Pb and Zn), three sequential extraction procedures were compared to determine the efficiency of the reagents used and the effects of the step order on the fractionation of metal species. In all cases, a magnesium nitrate solution (MgNIT) was previously used to extract exchangeable forms. In the first procedure (I), the next extraction step was performed with sodium acetate buffer (NaOAc), as used on calcareous soils, to dissolve active calcium carbonate. Then trace metals bound to different forms of oxi-hydroxides (NH(2)OH, TAMOx and TAMAs fractions) were extracted before organic matter/sulfide oxidation with hydrogen peroxide at pH 2.0 in nitric acid medium (OMHyd). Finally, residual bound metals (RESID) in each procedure were extracted with a nitric-hydrofluoric-perchloric acid mixture. The second procedure (II) was the same as I, but without the NaOAc step, because of the absence of carbonate in the study soil. In procedure III, the NaOAc step was omitted and the oxidizable organic/sulfide fraction was extracted with sodium hypochlorite at pH 8.5 (OMOCl) before the reducible fractions. This study first showed that NaOAc may remove considerable amounts of metals (especially Mn and Zn) in other forms than exchangeable ones. Procedures II and III give similar results for Fe, Mn and Zn forms, which were mainly found in fractions of inorganic soil components, but not for Cu and Pb. Copper distribution was affected by the position of the oxidation step in the sequence. In procedure II, where the oxidation step (OMHyd) ended the sequence, Cu was mainly recovered in the TAMOx fraction. However, in procedure III, where the oxidation step (OMOCl) preceded the NH(2)OH, TAMOx and TAMAs steps, Cu was found in both OMOCl and TAMOx fractions. Lead distribution varied with oxidation reagent: it was partly removed in the OMHyd fraction of procedures I and II, and to a much lower extent in the OMOCl fraction of procedure III, probably due to the alkaline pH of the reagent in the latter case.     

Study of partitioning and dynamics of metals in contaminated soil using modified four-step BCR sequential extraction procedure

The modified four-step BCR sequential extraction procedure (exchangeable and weak acid available species, reducible, oxidisable and residual fractions) was used to examine the distribution of As, Cd, Cr, Cu, Pb, and Zn with soil depth in an area (Baia Mare — Bozanta, Romania) with both high natural level of elements considered as toxic and historical pollution resulting from nonferrous metallurgy. The BCR approach proved a high metal input of anthropogenic origin down to 40 cm, while at lower depths the naturally elevated metal content must be considered. Results of the partitioning study and XRD analysis of solid matrix showed the greatest potential for chemical remobilisation of Cd, Zn, and Cu in weak acidic medium as well as their affinity for the oxidisable fraction (organic matter/sulphide). The tendency of Cr, Pb, and As to be immobilised as residual or reducible species on Fe-Mn oxides was evident. Although the partitioning of As in chemically inactive forms such as scorodite (FeAsO₄ · 2H₂O) soluble under reducible conditions and beudantite (PbFe₃(AsO₄)(SO₄)(OH)₂)), a residual species soluble in acid media, chemical mobilisation from soil in groundwater was confirmed. Dynamic processes of metal retention in soil under different conditions, namely acidic, reducing or oxidisable, were predicted from the Pearsonșs correlation analysis of element species with soil characteristics and components such as Fe, Mn, organic matter content, pH, and total element content, respectively. At the moment of the study, soil and groundwater in the area were found to be polluted with As, Cd, Cu, Pb and Zn. Presented at the 35th International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 26–30 May 2008.     

Chemical Speciation of Elements in Sediment Samples Collected at Lake Balaton

A modified sequential extraction procedure was applied to determination of the distribution of seven elements (Cd, Cu, As, Pb, Cr, Ni, Zn) in sediment samples collected at Lake Balaton. The fractions were (1) exchangeable and bound to carbonate, (2) bound to Fe/Mn oxide, (3) bound to organic matter and sulfide, and (4) acid soluble. These fractions have the advantage of providing better insight into the mechanism of association of metals with mineralogical phases of the sediments. Samples were taken in three seasons and the average concentration of the elements was calculated. Based on the results determined at 15 sampling points along the lake, it seems that Lake Balaton has not yet been polluted. Concentrations of species were below the Hungarian standard levels set for soils, and most of the elements were found in the acid-soluble fraction, indicating stable compounds in sediments. There were no significant changes in the individual seasonal concentrations of elements in this short monitoring period.     

缺氧沉积物中重金属形态连续萃取方法的稳定性研究

考察了海水养殖区域缺氧沉积物中重金属形态连续萃取法萃取过程中溶液pH值、温度变化和胶体形成对形态分离结果的影响。结果表明,连续萃取法Step1萃取酸溶态时,萃取液pH值的轻微升高使Pb和Zn的萃取结果明显降低;Step2萃取还原态时,萃取液pH值明显升高对重金属的萃取结果影响很小;Step3萃取有机质结合态时,萃取液pH值的降低对重金属萃取结果影响较小(除Pb外)。由于连续萃取法中各步萃取反应的热力学过程不同,Step1和Step2萃取后溶液温度轻微升高而在Step3中溶液温度稍微降低,溶液温度变化(<2.5℃)对重金属形态的影响很小。在Step1、Step2和Step4萃取过程中胶体的形成和存在,对萃取液Cd、Zn和Cu有明显的吸附影响;而在Step3萃取中萃取剂的分散作用有效控制了溶液中胶体的形成。因此采用连续萃取方法评价沉积物中的重金属形态时,控制萃取液pH值和胶体形成有利于提高萃取结果的稳定性和准确性。     

Estimation of environmental mobility of heavy metals using a sequential leaching of particulate material emitted from an opencast chrome mine complex

A four-stage sequential leaching procedure was applied to assess the bioavailability and environmental mobility of heavy metals (Cr, Fe, Cu, Ni and Cd) in total suspended particulate (TSP) material emitted from an opencast chrome mine complex (Kemi, Northern Finland). TSP material was collected on glass fibre filters by a high-volume sampler, and a sequential leaching procedure was used to determine the distribution of heavy metals between the water-soluble fraction (H2O), environmentally mobile fraction (CH3COONH4), the fraction bound to carbonate and oxides (HONH3Cl + CH3COOH), and the fraction bound to silicates and organic matter, that is the environmentally immobile fraction (HNO3 + HF + HCl). The sequential leaching procedure was also applied to the certified reference materials VKI (QC Loam Soil A) and PACS-2 (Marine Sediment) to evaluate the accuracy and reproducibility of the leaching procedure. The heavy metals were determined by graphite furnace atomic absorption spectrometry (GFAAS) and flame atomic absorption spectrometry (FAAS). The concentrations of metals in the water-soluble fraction (H2O) decreased in the order Fe >Cu >Cr >Ni >Cd, and in the environmentally mobile fraction (CH3COONH4) in the order Cu >Fe >Ni >Cr >Cd.