Determination of trace amounts of mercury(II) in water samples using a novel kinetic catalytic ligand substitution reaction of hexacyanoruthenate(II)

A simple, sensitive, selective and rapid kinetic catalytic method has been developed for the determination of Hg(II) ions at micro-level. This method is based on the catalytic effect of Hg(II) ion on the rate of substitution of cyanide in hexacyanoruthenate(II) with nitroso-R-salt (NRS) in aqueous medium and provides good accuracy and precision. The concentration of Hg(II) catalyst varied from 4.0 to 10.0 × 10⁻⁶ M and the progress of reaction was followed spectrophotometrically at 525 nm (λ_max of purple-red complex [Ru(CN)₅NRS]³⁻,  = 3.1 × 10³ M⁻¹ s⁻¹) under the optimized reaction conditions; 8.75 × 10⁻⁵ M [Ru(CN)₆⁴⁻], 3.50 × 10⁻⁴ M [nitroso-R-salt], pH 7.00 ± 0.02, ionic strength, I = 0.1 M (KCl), temp 45.0 ± 0.1 °C. The linear calibration curves, i.e. calibration equations between the absorbance at fixed times (t = 15, 20 and 25 min) versus concentration of Hg(II) ions were established under the optimized experimental conditions. The detection limit was found to be 1.0 × 10⁻⁷ M of Hg(II). The effect of various foreign ions on the proposed method has also been studied and discussed. The method has been applied to the determination of mercury(II) in aqueous solutions.     

Highly selective adsorption of cadmium ions by water‐dispersible magnetic thioglycolic acid/graphene oxide composites

A new selective and fast procedure based on magnetic dispersive solid‐phase extraction and zeta potential analysis is proposed for the determination of Cd (II) in some food samples. In the developed method, novel magnetic nanoparticles modified with thioglycolic acid were synthesized/characterized and also applied for quantitative determination of trace amounts of Cd (II) in food samples. The prepared nanoparticles were characterized via infrared spectroscopy, electron microscopy and adsorption–desorption experiments. These magnetic nanocomposites carrying Cd (II) could be easily separated from real samples simply by applying an external magnetic field; no filtration or centrifugation was necessary. Several parameters affecting the analytical performance, such as sample pH, amounts of nanocomposite sample, desorption solution volumes and coexisting ions, were investigated in detail. The detection limit of the method was 0.1 μg l^?1 while the relative standard deviation was 1.2% for a Cd (II) concentration of 0.5 mg l^?1. The proposed method was successfully applied to food sample analysis and standard reference material samples with satisfactory results, and excellent recoveries were obtained in the range 95–99% even when the matrix, such as sea water, was complex.     

Simultaneous determination of Fe(II) and Fe(III) by kinetic spectrophotometric H-point standard addition method

The H-point standard addition method (HPSAM) for simultaneous determination of Fe(II) and Fe(III) is described. The method is based on the difference in the rate of complex formation of iron in two different oxidation states with Gallic acid (GA) at pH 5. Fe(II) and Fe(III) can be determined in the range of 0.02–4.50 μg ml⁻¹ and 0.05–5.00 μg ml⁻¹, respectively, with satisfactory accuracy and precision in the presence of other metal ions, which rapidly form complexes with GA under working conditions. The proposed method was successfully applied for simultaneous determination of Fe(II) and Fe(III) in several environmental and synthetic samples with different concentration ratios of Fe(II) and Fe(III).     

Kinetic spectrophotometric determination of sulfide using whole kinetic curve and a fixed time method

The univariate and multivariate calibration method was applied for the determination of sulfide based on the addition reaction of sulfide with new fuchsin at pH 8 and 25°C. The decrease in absorbance of new fuchsin at 540 nm over a fixed time is proportional to the concentration of sulfide over the range of 0.05-2.5 μg ml⁻¹. The experimental calibration matrix for partial least squares calibration (PLS) method was designed with 20 samples. The cross-validation method was used for selecting the number of factors. The root mean square difference (RMSD) was 0.0843. The effects of various cations and anions on sulfide determination have been investigated.     

Detection and spectrophotometric determination of EDTA with cobalt(II) and phosphomolybdic acid in urine and detergents

A simple, rapid, sensitive and selective method for the microgram detection and spectrophotometric determination of EDTA in water, human urine and detergents, based on its reaction with Co(II) and phosphomolybdic acid at pH 0.5–2.0 is reported. Absorbance is measured against Co(II)–phosphomolybdic acid reference solution at 750 nm. The effect of time, temperature, pH and Co(II) or phosphomolybdic acid concentration is studied, and optimum operating conditions are established. Beer's law is applicable in the concentration range 0.3–1.9 μg ml⁻¹ of 10⁻⁵M EDTA. Its detection limit is 0.14 μg in the solution phase and 0.03 μg in the resin phase. The relative standard deviation is ±0.13 μg. Ag(I), Zn(II), Cu(II), Ni(II), Pb(II), Cd(II), Ca(II), Mg(II), Fe(III), Cr(III), U(VI), chloride, nitrite, phosphate, oxalate, borate and amino acids do not interfere.     

A simple and selective flow-injection spectrophotometric determination of copper(II) by using acetylsalicylhydroxamic acid

A new simple, and rapid flow-injection spectrophotometric method is developed for the determination of trace amounts of Cu(II) by using a new chromogenic reagent acetylsalicylhydroxamic acid (AcSHA). The method is based on the formation of colored Cu(II)-(AcSHA)₂ complex. The optimum conditions for the chromogenic reaction of Cu(II) with AcSHA is studied and the colored (green) complex is selectively monitored at λ_max 700 nm. With the reagent carrier solvent (dimethylsulfoxide (DMSO) and acetate buffer, pH 4.2) flow-rate of 1 ml min⁻¹, a detection limit (2S) of 1 μg l⁻¹ Cu(II) was obtained at a sampling rate of 80 sample h⁻¹. The calibration graph was linear in the Cu(II) concentration range 5-120 μg l⁻¹. The relative standard deviation (n=10) was 0.64% for a sample containing 60 μg l⁻¹ Cu(II). The detailed study of various interferences confirmed the high selectivity of the developed method. The method was successfully applied to determine trace amounts of copper(II) in river and seawater samples. The accuracy of the method was demonstrated by the analysis of standard reference materials C12X3500 and C14XHS 50.     

Simultaneous kinetic spectrophotometric determination of Cu(II), Co(II) and Ni(II) using partial least squares (PLS) regression

A partial least squares (PLS-1) calibration model based on kinetic—spectrophotometric measurement, for the simultaneous determination of Cu(II), Ni(II) and Co(II) ions is described. The method was based on the difference in the rate of the reaction between Co(II), Ni(II) and Cu(II) ions with 1-(2-pyridylazo)2-naphthol in a pH 5.8 buffer solution and in micellar media at 25°C. The absorption kinetic profiles of the solutions were monitored by measuring the absorbance at 570 nm at 2 s intervals during the time range of 0–10 min after initiation of the reaction. The experimental calibration matrix for the partial least squares (PLS-1) model was designed with 30 samples. The cross-validation method was used for selecting the number of factors. The results showed that simultaneous determination could be performed in the range 0.1-2 μg mL⁻¹ for each cation. The proposed method was successfully applied to the simultaneous determination of Cu(II), Ni(II) and Co(II) ions in water and in synthetic alloy samples.      

A novel spectrophotometric method for determination of cyanide using cobalt (II) phthalocyanine tetracarboxylate as a chromogen

Cobalt (II) phthalocyanine tetracarboxylate [Co (II)Pc-COOH] has been prepared and used in aqueous solutions as a novel chromogenic reagent for the spectrophotometric determination of cyanide ion. The method is based on measuring the increase in the intensity of the monomer peak in the reagent absorbance at 682 nm due to the formation of a 1 : 2 [Co (II)Pc-COOH] : [CN] complex. The complex exhibits a molar absorptivity (ε) of 7.7 × 10⁴ L mol^?1 cm^?1 and a formation constant (K_f ) of 5.4 ± 0.01 × 10⁶ at 25 ± 0.1°C. Beer's law is obeyed over the concentration range 0.15–15 µg mL^?1 (5.8 × 10^?6–5.8 × 10^?4 M) of cyanide ion, the detection limit is 20 ng mL^?1 (7.7 × 10^?7 M) the relative standard deviation is ±0.7% (n = 6) and the method accuracy is 98.6 ± 0.9%. Interference by most common ions is negligible, except that by sulphite. The proposed method is used for determining cyanide concentration in gold, silver and chromium electroplating wastewater bath solutions after a prior distillation with 1 : 1 H₂SO₄ and collection of the volatile cyanide in 1 M NaOH solution containing lead carbonate as recommended by ASTM, USEPA, ISO and APAHE separation procedures. The results agree fairly well with potentiometric data obtained using the solid state cyanide ion selective electrode.     

Second derivative spectrophotometric method for simultaneous determination of cobalt, nickel and iron using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

A simple, sensitive and rapid derivative spectrophotometric method using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) has been developed for simultaneous determination of Co(II), Ni(II) and Fe(II) which have very similar chemical behavior and appear together in many real samples. The complexes of all these metal ions with 5-Br-PADAP were formed immediately at pH 7.0 ammonium acetate buffered solution and were stable for at least 24 h. Second derivative spectra were selected for evaluation, because working wavelength determination was more precise and spectral overlap was less than in the ordinary and first derivative spectra. Three wavelengths at which the complexes exhibit extremum ²D values for Co(II), Ni(II) and Fe(II) were selected as analytical wavelengths, i.e., 640, 600 and 740 nm, respectively. Calibration curves drawn with zero-to-peak values at mentioned wavelengths were linear between 80 and 2000 ng ml⁻¹ for each metal ion. Concentrations of Co(II) and Ni(II) were calculated from the total ²D values and the sum of the linear equations for these three cations at 640 and 600 nm, after Fe(II) assay by making use of the ²D value at 740 nm. Limits of detection (LOD) for Co(II), Ni(II) and Fe(II) were 2.7, 13.9 and 3.0 ng ml⁻¹, respectively. The method has been applied to tool steel and heater resistance wire samples successfully.     

A novel spectrophotometric method for batch and flow injection determination of sulfite in beverages

A novel spectrophotometric assay method for batch and flow injection determination of sulfite in beverages is described. The method involves a reaction with diaquacobyrinic acid heptamethyl ester (diaquacobester, DACbs) in acetate buffer of pH 3 to form a highly stable sulfite cobester complex (SO₃Cbs). In the absence of sulfite, the reagent displays three absorption maxima at 349, 409 and 525 nm. Addition of sulfite is associated with the development of a new absorption band at 313 nm, an increase in the intensity of the band at 425 nm and a decrease in the absorbance of the bands at 349 and 525 nm. Variations of the absorptions at 313, 349, 425 and 525 nm are linearly proportional to sulfite concentrations over the range of 0.05–25 μg ml⁻¹with a detection limit of 0.01–0.2 μg ml⁻¹. Negligible interferences are caused by most common ions. Validation of the method according to the quality assurance standards shows suitability for quality control assessment of sulfite in complex matrices without prior treatment. The method has the advantages of high selectivity, good sensitivity, fast reaction, high stability of the reagent and reaction product and absorbance measurements at four different wavelengths in the same run. The method is successfully applied to determine the sulfite contents of some beverages. The results compare fairly well with data obtained using the standard method.     

Artificial neural networks for simultaneous spectrophotometric differential kinetic determination of Co(II) and V(IV)

A method for simultaneous analysis of V(IV) and Co(II) has been developed by using artificial neural network (ANN). This method is based on the difference of the chemical reaction rate of V(IV) and Co(II) with Fe(III) in the presence of chromogenic reagent, 1,10-phenanthroline. The reduced product of the reaction, Fe(II), can form a colored complex with 1,10-phenanthroline and make a visible spectrophotometric signal for indirect monitoring of the V(IV) and Co(II) concentrations. Feed forward neural networks have been trained to quantify considered metal ions in mixtures under optimum conditions. The networks were shown to be capable of correlating reduced spectral kinetic data using principal component analysis (PCA) of mixtures with individual metal ion. In this way an ANN containing three layers of nodes was trained. Sigmoidal and linear transfer functions were used in the hidden and output layers, respectively, to facilitate nonlinear calibration. Both V(IV) and Co(II) were analyzed in the concentration range of 0.1-4.0 μg ml⁻¹. The proposed method was also applied satisfactorily to the determination of considered metal ions in several synthetic and water samples.     

A novel spectrophotometric method for batch and flow injection determination of cyanide in electroplating wastewater

A sensitive and highly selective spectrophotometric method is described for the determination of cyanide. It is based on a reaction of cyanide with aquacyanocobyrinic acid heptamethyl ester (ACCbs) reagent (orange color) at pH 9.5 to give dicyanocobester (DCCbs) (violet color). The increase of the absorption bands of the reaction product at 368 and 580 nm and the decrease of the reagent band at 353 nm are linearly proportional to the cyanide concentration. The method is used in static mode for determining cyanide over the concentration range 0.04-1.20 μg ml⁻¹ with a detection limit of 0.02 μg ml⁻¹ and for hydrodynamic analysis of 0.4-5.2 μg ml⁻¹ cyanide. Application for batch and flow injection monitoring of cyanide in electroplating wastewater samples gives results agree within ± 1.2% with those obtained by the standard potentiometry using the cyanide ion selective electrode. The method is practically free from interferences by PO₄³⁻, NO₃⁻, NO₂⁻, SO₄²⁻, F⁻, Cl⁻, Br⁻, I⁻, S²⁻ and SCN⁻ ions and gives results with average recoveries of 97.6-99.2%. Advantages offered by using ACCbs as a chromogen for cyanide assay are: (i) high selectivity and sensitivity of the coordination site of the reagent towards cyanide ion; (ii) fast reaction, since legation takes place at the axial position of the reagent; (iii) good solubility and stability of the reagent in aqueous solutions over a wide pH range; (iv) high stability of the reagent (ACCbs) and the colored complex product (DCCbs) and (v) possible absorbance measurements at three different wavelengths.     

Catalytic and kinetic spectrophotometric method for determination of vanadium(V) by 2,3,4-trihydroxyacetophenonephenylhydrazone

A new catalytic and kinetic spectrophotometric method for the determination of vanadium(V) was studied using 2,3,4-trihydroxyacetophenonephenylhydrazone (THAPPH) as an analytical reagent. The present method was developed on the catalytic effect of vanadium on oxidation of THAPPH by hydrogen peroxide in hydrochloric acid–potassium chloride buffer (pH = 2.8) at the 20th minute. The metal ion has formed 1:2 (M:L) complex with THAPPH. Beer’s law was obeyed in the range 20–120 ng/mL of V(V) at λ_max 390 nm. The sensitivity of the method was calculated in terms of molar absorptivity (1.999 × 10⁵ L mol⁻¹cm⁻¹) and Sandell’s sensitivity (0.000254 μg cm⁻²), shows that this method is more sensitive. The standard deviation (0.0022), relative standard deviation (0.56%), confidence limit (±0.0015) and standard error (0.0007) revealed that the developed method has more precision and accuracy. The stability constant was calculated with the help of Asmu’s (9.411 × 10⁻¹¹) and Edmond’s & Birnbaum’s (9.504 × 10⁻¹¹) methods at room temperature. The interfering effect of various cations and anions was also studied. The present method was successfully applied for the determination of vanadium(V) in environmental and alloy samples. The method’s validity was checked by comparing the results obtained with atomic-absorption spectrophotometry and also by evaluation of results using F-test.     

Development of sequential injection spectrophotometric method for determination of mercury (II) using pyrogallol red

A sequential injection analysis (SIA) spectrophotometric method for the determination of trace amount of mercury (II) with pyrogallol red (PGR) was described. The method was based on the measurement of absorbance of the mercury (II)–PGR complex, yielding a light yellow-coloured product at pH 9.0 with absorption maximum at 370 nm. The SIA parameters affecting the signal response were optimised in order to obtain the better sensitivity and minimum reagent consumption. The linear range for determination of mercury (II) was over the range of 0.1–2.0 mg L^?1. The limit of detection and limit of quantification, calculated following IUPAC were 0.06 and 0.10 mg L^?1, respectively. The repeatability was 1.25% (n = 10) for 0.5 mg L^?1 of mercury (II). The proposed method was successfully applied to determine the mercury (II) in commercial cosmetics, local Thai traditional medicines and water samples with a sampling rate of 40 h^?1. Results obtained were in justifiable agreement with those obtained by the official ICP-MS method at the 95% confidence level.     

Simultaneous kinetic spectrophotometric determination of cyanide and thiocyanate using the partial least squares (PLS) regression

The partial least squares (PLS-1) calibration model based on spectrophotometric measurement, for the simultaneous determination of CN⁻ and SCN⁻ ions is described. The method is based on the difference in the rate of the reaction between CN⁻ and SCN⁻ ions with chloramine-T in a pH 4.0 buffer solution and at 30 °C. The produced cyanogen chloride (CNCl) reacts with pyridine and the product condenses with barbituric acid and forms a final colored product. The absorption kinetic profiles of the solutions were monitored by measuring absorbance at 578 nm in the time range 20-180 s after initiation of the reaction with 2 s intervals. The experimental calibration matrix for partial least squares (PLS-1) calibration was designed with 31 samples. The cross-validation method was used for selecting the number of factors. The results showed that simultaneous determination could be performed in the range 10.0-900.0 and 50.0-1200.0 ng mL⁻¹ for CN⁻ and SCN⁻ ions, respectively. The proposed method was successfully applied to the simultaneous determination of cyanide and thiocyanate in water samples.     

一种基于二喹啉甲酸- Cu+显色反应的毛细管电泳检测蛋白质的新方法

采用毛细管电泳法和蛋白质显色反应-二喹啉甲酸(BCA)法,结合微波辅助反应,在60 mmol/L硼酸盐缓冲液(pH 9.5)中,实现了对蛋白质的快速毛细管电泳分析检测。同时以β-环糊精为包合添加剂,实现了BCA-Cu+复合物和游离BCA的分离,从而在波长200 nm处以测定特征生成的BCA-Cu+复合物来间接检测蛋白质,其峰强度比直接检测蛋白质自身吸收的峰强度提高了2个数量级。对于转铁蛋白、蓖麻毒素,其线性范围分别为2～200 mg/L和2～100 mg/L,检出限分别为0.33和0.37 mg/L。将该方法成功地应用于第一届蓖麻毒素国际实验室间比对测试的部分样品,含量测定结果满意。     

Catalytic kinetic spectrophotometric determination of trace amounts of palladium with dahlia violet after separation and preconcentration on sulphydryl dextran gel

A sensitive and selective kinetic catalytic spectrophotometric method has been described for the determination of trace amounts of palladium(II). The method is based on the catalytic effects of palladium(II) on the reduction reactions of Dahlia Violet with sodium dihydrogen hypophosphite (NaH₂PO₂) in a sulfuric acid medium. Under optimal conditions, trace amounts of palladium(II) can be determined. A good linear range has been obtained in the concentration range of Pd(II) over 0.001–0.028 μg/mL with a detection limit of 5.9 × 10⁻¹⁰ g/mL. The method has been successfully applied to the determination of palladium(II) in ore and soil samples. The relative standard deviation was less than 5.0% (n = 11). The coexisting ions were eliminated by preconcentration and separation on sulphydryl dextran gel with satisfactory results. The text was submitted by the authors in English.     

Adsorption behavior and mechanism of Cu(II) onto carbonate-substituted hydroxyapatite in the presence of humic acid

In this study, adsorption behavior and mechanism of Cu(II) onto carbonate-substituted hydroxyapatite (CHAP) in the absence and presence of humic acid (HA) were studied in batch experiments. The results showed that carbonate incorporation in HAP could significantly enhance the adsorption of Cu(II). In ternary systems, the presence of HA led to an increase in Cu(II) adsorption, dependent on HA concentration. Kinetic studies showed that pseudo-second-order kinetic model better described the adsorption process of Cu(II) onto CHAP and equilibrium data were best described by Sips models. The order of addition sequences of substrates was found to have a noticeable effect on Cu(II) adsorption onto CHAP. The general trend with respect to Cu(II) adsorption being: (CHAP–Cu)–HA?>?(CHAP–HA)–Cu?>?(Cu–HA)–CHAP. The present findings were important for estimating and optimizing the removal of Cu(II) ions by using CHA as a potential adsorbent.     

Simultaneous spectrophotometric determination of Sn(II) and Sn(IV) by mean centering of ratio kinetic profiles and partial least squares methods

Two spectrophotometric methods are described for the simultaneous determination of binary mixtures of Sn(II) and Sn(IV) in water samples and fruit juice samples, without prior separation steps, using the mean centering of ratio kinetic profiles and partial least squares (PLS) methods. The methods are based on the difference in the rate of the reactions of Sn(II) and Sn(IV) with pyrocatechol violet at pH 4.0. The methods allow rapid and accurate determination of Sn(II) and Sn(IV). The analytical characteristics of the methods for the simultaneous determination of binary mixtures of Sn(II) and Sn(IV) were calculated. The results showed that the methods were capable to simultaneous determination of 0.1–1.80 mg L⁻¹ each of cations. The proposed methods were successfully applied to the simultaneous determination of Sn(II) and Sn(IV)in an orange juice sample.     

Selective spectrophotometric determination of palladium(II) with 2(5-nitro-2-pyridylazo)-5-(N-propyl-N-3-sulfopropylamino)phenol(5-NO(2).PAPS) and tartaric acid with 5-NO(2).PAPS-niobium(V) complex

Spectrophotometric determinations of palladium(II) and tartaric acid were respectively investigated by using the color reactions between 2(5-nitro-2-pyridylazo)-5-(N-propyl-N-3-sulfopropylamino)phenol(5-NO₂.PAPS) and palladium(II) in strong acidic media, and between 5-NO₂.PAPS, niobium(V) tartaric acid in weak acidic media. The calibration graphs were linear in the range of 0–25 μg/10 ml palladium(II), with an apparent molecular coefficient () of 6.2×10⁴ l mol⁻¹ cm⁻¹ at 612 nm, and 0–23 μg/10 ml tartaric acid with =1.08×10⁶ l mol⁻¹ cm⁻¹ at 612 nm, respectively. The proposed methods were selective and sensitive in comparison with other chelating pyridylazo dyes–palladium(II) or metavanadic acid–tartaric acid method, and the effect of foreign ions such as copper(II) was negligible for the assay of palladium(II) with 5-NO₂.PAPS.