Shear-induced aggregation and break up of fibril clusters close to the percolation concentration

To probe the behaviour of fibrillar assemblies of ovalbumin under oscillatory shear, close to the percolation concentration, c_p (7.5%), rheo-optical measurements and Fourier transform rheology were performed. Different results were found close to c_p (7.3%), compared to slightly further away from c_p (6.9 and 7.1%). For 6.9 and 7.1%, a decrease in complex viscosity, and a linear increase in birefringence, n, with increasing strain was observed, indicating deformation and orientation of the fibril clusters. For 7.3%, a decrease in complex viscosity was followed by an increase in complex viscosity with increasing strain, which coincided with a strong increase in n, dichroism, n, and the intensity of the normalized third harmonic (I₃/I₁). This regime was followed by a second decrease in complex viscosity, where n,n and I₃/I₁ decreased. In the first regime where the viscosity was decreasing with increasing strain, deformation and orientation of existing clusters takes place. At higher oscillatory shear, a larger deformation occurs and larger structures are formed, which is most likely aggregation of the clusters. Finally, at even higher strains, the clusters break up again. An increase in complex viscosity, n, n and I₃/I₁ was observed when a second strain sweep was performed 30 min after the first. This indicates that the shear-induced cluster formation and break up are not completely reversible, and the initial cluster size distribution is not recovered after cessation of flow.     

The chaotic response of a fluttering panel: The influence of maneuvering

The influence of maneuvering on the chaotic response of a fluttering buckled plate on an aircraft has been studied. The governing equations, derived using Lagrangian mechanics, include geometric non-linearities associated with the occurrence of tensile stresses, as well as coupling between the angular velocity of the maneuver and the elastic degrees of freedom. Numerical simulation for periodic and chaotic responses are conducted in order to analyze the influence of the pull-up maneuver on the dynamic behavior of the panel. Long-time histories phase-plane plots, and power spectra of the responses are presented. As the maneuver (load factor) increases, the system exhibits complicated dynamic behavior including a direct and inverse cascade of subharmonic bifurcations, intermittency, and chaos. Beside these classical routes of transition from a periodic state to chaos, our calculations suggest amplitude modulation as a possible new mode of transition to chaos. Consequently this research contributes to the understanding of the mechanisms through which the transition between periodic and strange attractors occurs in, dissipative mechanical systems. In the case of a prescribed time dependent maneuver, a remarkable transition between the different types of limit cycles is presented.Nomenclature a plate length - a _r u _r /h - D plate bending stiffness - E modulus of elasticity - g acceleration due to gravity - h plate thickness - j₁,j₂,j₃ base vectors of the body frame of reference - K spring constant - M Mach number - n 1 + ₀/g - N ₁ applied in-plane force - p–p aerodynamic pressure - P pa ⁴/Dh - q ₀/2 - Q _r generalized Lagrangian forces - R rotation matrix - R ₄ N, a ²/D - t time - kinetic energy - u plate deflection - u displacement of the structure - u _r modal amplitude - v₀ velocity - x coordinates in the inertial frame of reference - z coordinates in the body frame of reference - Ka/(Ka+Eh) - - elastic energy - 2qa ³/D - a/_mh - Poisson's ratio - material coordinates - air density - _m plate density - - _r prescribed functions - _r sin(r z/a) - angular velocity - a/v₀ - skew-symmetric matrix form of the angular velocity     

Flow in porous media III: Deformable media

Stokes flow in a deformable medium is considered in terms of an isotropic, linearly elastic solid matrix. The analysis is restricted to steady forms of the momentum equations and small deformation of the solid phase. Darcy's law can be used to determine the motion of the fluid phase; however, the determination of the Darcy's law permeability tensor represents part of the closure problem in which the position of the fluid-solid interface must be determined.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A ^* interfacial area of the- interface contained within a unit cell, m² - A _e ^* area of entrances and exits for the-phase contained within a unit cell, m² - E Young's modulus for the-phase, N/m² - e i unit base vectors (i = 1, 2, 3) - g gravity vector, m²/s - H height of elastic, porous bed, m - k unit base vector (=e ₃) - characteristic length scale for the-phase, m - L characteristic length scale for volume-averaged quantities, m - n unit normal vector pointing from the-phase toward the-phase (n = -n ) - p pressure in the-phase, N/m² - P p – g·r, N/m² - r ₀ radius of the averaging volume, m - r position vector, m - t time, s - T total stress tensor in the-phase, N/m² - T ⁰ hydrostatic stress tensor for the-phase, N/m² - u displacement vector for the-phase, m - V averaging volume, m₃ - V volume of the-phase contained within the averaging volume, m³ - v velocity vector for the-phase, m/s Greek Letters V /V, volume fraction of the-phase - mass density of the-phase, kg/m³ - shear coefficient of viscosity for the-phase, Nt/m² - first Lamé coefficient for the-phase, N/m² - second Lamé coefficient for the-phase, N/m² - bulk coefficient of viscosity for the-phase, Nt/m² - T –T ⁰ , a deviatoric stress tensor for the-phase, N/m²     

Transport in ordered and disordered porous media V: Geometrical results for two-dimensional systems

In this paper we continue the geometrical studies of computer generated two-phase systems that were presented in Part IV. In order to reduce the computational time associated with the previous three-dimensional studies, the calculations presented in this work are restricted to two dimensions. This allows us to explore more thoroughly the influence of the size of the averaging volume and to learn something about the use of anon-representative region in the determination of averaged quantities.

Nomenclature

Roman Letters A interfacial area of the– interface associated with the local closure problem, m² - a _i i=1, 2, gaussian probability distribution used to locate the position of particles - l unit tensor - characteristic length for the-phase particles, m - ⁰ reference characteristic length for the-phase particles, m - characteristic length for the-phase, m - _i i=1,2,3 lattice vectors, m - m convolution product weighting function - m _V special convolution product weighting function associated with a unit cell - n _i i=1, 2 integers used to locate the position of particles - n unit normal vector pointing from the-phase toward the-phase - r _p position vector locating the centroid of a particle, m - r gaussian probability distribution used to determine the size of a particle, m - r ₀ characteristic length of an averaging region, m - V averaging volume, m³ - V volume of the-phase contained in the averaging volume,V, m³ - x position of the centroid of an averaging area, m - x ₀ reference position of the centroid of an averaging area, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters V /V, volume average porosity - _{a i} standard deviation ofa _i - _r standard deviation ofr - intrinsic phase average of      

Effect of measuring volume length on two-component laser velocimeter measurements in a turbulent boundary layer

The effects of finite measuring volume length on laser velocimetry measurements of turbulent boundary layers were studied. Four different effective measuring volume lengths, ranging in spanwise extent from 7 to 44 viscous units, were used in a low Reynolds number (Re=1440) turbulent boundary layer with high data density. Reynolds shear stress profiles in the near-wall region show that u v strongly depends on the measuring volume length; at a given y-position, u v decreases with increasing measuring volume length. This dependence was attributed to simultaneous validations on the U and V channels of Doppler bursts coming from different particles within the measuring volume. Moments of the streamwise velocity showed a slight dependence on measuring volume length, indicating that spatial averaging effects well known for hot-films and hot-wires can occur in laser velocimetry measurements when the data density is high.List of symbols time-averaged quantity - u wall friction velocity, ( _w /)^1/2 - v kinematic viscosity - d _p pinhole diameter - l _eff spanwise extent of LDV measuring volume viewed by photomultiplier - l ⁺ non-dimensional length of measuring volume, l _eff u /v - y ⁺ non-dimensional coordinate in spanwise direction, y u /v - z ⁺ non-dimensional coordinate in spanwise direction, z u /v - U ⁺ non-dimensional mean velocity, /u - u instantaneous streamwise velocity fluctuation, U &#x2329;U - v instantaneous normal velocity fluctuation, V–V - u RMS streamwise velocity fluctuation, u ^21/2 - v RMS normal velocity fluctuation, v ^21/2 - Re Reynolds number based on momentum thickness, U 0/v - R _uv cross-correlation coefficient, u v/u v - R₁₂(0, 0, z) two point correlation between u and v with z-separation, <u(0, 0, 0) v (0, 0, z)>/<u(0, 0, 0) v (0, 0, 0)> - N rate at which bursts are validated by counter processor - T Taylor time microscale, u (dv/dt²)^–1/2     

On natural convection from a vertical plate with a prescribed surface heat flux in porous media

This paper presents a theoretical and numerical investigation of the natural convection boundary-layer along a vertical surface, which is embedded in a porous medium, when the surface heat flux varies as (1 +x ²)), where is a constant andx is the distance along the surface. It is shown that for > -1/2 the solution develops from a similarity solution which is valid for small values ofx to one which is valid for large values ofx. However, when -1/2 no similarity solutions exist for large values ofx and it is found that there are two cases to consider, namely < -1/2 and = -1/2. The wall temperature and the velocity at large distances along the plate are determined for a range of values of .Notation g Gravitational acceleration - k Thermal conductivity of the saturated porous medium - K Permeability of the porous medium - l Typical streamwise length - q _w Uniform heat flux on the wall - Ra Rayleigh number, =gK(q _w /k)l/(v) - T Temperature - Too Temperature far from the plate - u, v Components of seepage velocity in the x and y directions - x, y Cartesian coordinates - Thermal diffusivity of the fluid saturated porous medium - The coefficient of thermal expansion - An undetermined constant - Porosity of the porous medium - Similarity variable, =y(1+x ) ^/3/x ^1/3 - A preassigned constant - Kinematic viscosity - Nondimensional temperature, =(T – T )Ra^1/3 k/qw - Similarity variable, = =y(log_e x)^1/3/x ^2/3 - Similarity variable, =y/x ^2/3 - Stream function     

LDA measurements in low Reynolds number turbulent boundary layer

LDA measurements of the mean velocity in a low Reynolds number turbulent boundary layer allow a direct estimate of the friction velocity U from the value of /y at the wall. The trend of the Reynolds number dependence of / is similar to the direct numerical simulations of Spalart (1988).     

On the cross-effects of coupled macroscopic transport equations in porous media

In this paper, the derivation of macroscopic transport equations for this cases of simultaneous heat and water, chemical and water or electrical and water fluxes in porous media is presented. Based on themicro-macro passage using the method of homogenization of periodic structures, it is shown that the resulting macroscopic equations reveal zero-valued cross-coupling effects for the case of heat and water transport as well as chemical and water transport. In the case of electrical and water transport, a nonsymmetrical coupling was found.Notations b mobility - c concentration of a chemical - D rate of deformation tensor - D molecular diffusion coefficient - D _ij ^eff macroscopic (or effective) diffusion tensor - electric field - E ₀ initial electric field - k _ij molecular tensor - j, j ^*, current densities - K _ij macroscopic permeability tensor - l characteristic length of the ERV or the periodic cell - L characteristic macroscopic length - L _ijkl coupled flows coefficients - n _i unit outward vector normal to - p pressure - q _t ,q _t ⁺ , heat fluxes - q _c ,q _c ⁺ , chemical fluxes - s specific entropy or the entropy density - S entropy per unit volume - t time variable - t _ij local tensor - T absolute temperature - v _i velocity - V ₀ initial electric potential - V electric potential - x macroscopic (or slow) space variable - y microscopic (or fast) space variable - _i local vectorial field - _i local vectorial field - electric charge density on the solid surface - , bulk and shear viscosities of the fluid - _ij local tensor - _ij local tensor - _i local vector - _ij molecular conductivity tensor - _ij ^eff effective conductivity tensor - homogenization parameter - fluid density - ₀ ion-conductivity of fluid - _ij dielectric tensor - _i ¹ , _i ² , _i ³ local vectors - ⁴ local scalar - _S solid volume in the periodic cell - _L volume of pores in the periodic cell - boundary between _S and _L - ^s rate of entropy production per unit volume - total volume of the periodic cell - _l volume of pores in the cell On leave from the Politechnika Gdanska; ul. Majakowskiego 11/12, 80-952, Gdask, Poland.     

On forced vibration of anisotropic cylinders

Summary The dynamic response of a circular cylinder with thick walls of transverse curvilinear isotropy subjected to a uniformly distributed pressure varying periodically with time is analyzed by means of the Laplace transformation, and the exact solution is obtained in closed form. The previously obtained solutions for forced vibrations with isotropy, and free vibrations with transverse curvilinear isotropy are included as special cases of the general results reported here.Nomenclature t time - r, , z cylindrical coordinates - _ii components of normal strain - _ii components of normal stress - u radial displacement - c _ij elastic constant - mass density - c ² c ₁₁/ - ² c ₂₂/c ₁₁ - a, b inner, outer radius of the cylinder - , A, B constants - forced angular frequency - function defined by (9) - p, real, complex variables - constant defined by (14) - real number - , Lamé elastic constants - J (x) Bessel function of first kind - Y (x) Bessel function of second kind - I (x) modified Bessel function of first kind - K (x) modified Bessel function of second kind     

Transcendentally small transversality in the rapidly forced pendulum

The rapidly forced pendulum equation with forcing sin((t/), where =<₀^p,p = 5, for ₀, sufficiently small, is considered. We prove that stable and unstable manifolds split and that the splitting distanced(t) in the ( ,t) plane satisfiesd(t) = sin(t/) sech(/2) +O( ₀ exp(–/2)) (2.3a) and the angle of transversal intersection,, in thet = 0 section satisfies 2 tan/2 = 2S _s = (/2) sech(/2) +O(( ₀ /) exp(–/2)) (2.3b) It follows that the Melnikov term correctly predicts the exponentially small splitting and angle of transversality. Our method improves a previous result of Holmes, Marsden, and Scheuerle. Our proof is elementary and self-contained, includes a stable manifold theorem, and emphasizes the phase space geometry.     

Optical co-ordinates in general relativity 2 — the problem of distance

Summary Let denote the congruence of null geodesics associated with a given optical observer inV ₄. We prove that determines a unique collection of vector fieldsM₍₎ ( =1, 2, 3) and ₍₀₎ overV ₄, satisfying a weak version of Killing's conditions.This allows a natural interpretation of these fields as the infinitesimal generators of spatial rotations and temporal translation relative to the given observer. We prove also that the definition of the fieldsM₍₎ and ₍₀₎ is mathematically equivalent to the choice of a distinguished affine parameter f along the curves of, playing the role of a retarded distance from the observer.The relation between f and other possible definitions of distance is discussed.

---

Sommario Sia la congruenza di geodetiche nulle associata ad un osservatore ottico assegnato nello spazio-tempoV ₄. Dimostriamo che determina un'unica collezione di campi vettorialiM₍₎ ( =1, 2, 3) e ₍₀₎ inV ₄ che soddisfano una versione in forma debole delle equazioni di Killing. Ciò suggerisce una naturale interpretazione di questi campi come generatori infinitesimi di rotazioni spaziali e traslazioni temporali relative all'osservatore assegnato. Dimostriamo anche che la definizione dei campiM₍₎, ₍₀₎ è matematicamente equivalente alla scelta di un parametro affine privilegiato f lungo le curve di, che gioca il ruolo di distanza ritardata dall'osservatore. Successivamente si esaminano i legami tra f ed altre possibili definizioni di distanza in grande.

---

---

Work performed in the sphere of activity of: Gruppo Nazionale per la Fisica Matematica del CNR.     

Flow in porous media I: A theoretical derivation of Darcy's law

Stokes flow through a rigid porous medium is analyzed in terms of the method of volume averaging. The traditional averaging procedure leads to an equation of motion and a continuity equation expressed in terms of the volume-averaged pressure and velocity. The equation of motion contains integrals involving spatial deviations of the pressure and velocity, the Brinkman correction, and other lower-order terms. The analysis clearly indicates why the Brinkman correction should not be used to accommodate ano slip condition at an interface between a porous medium and a bounding solid surface.The presence of spatial deviations of the pressure and velocity in the volume-averaged equations of motion gives rise to aclosure problem, and representations for the spatial deviations are derived that lead to Darcy's law. The theoretical development is not restricted to either homogeneous or spatially periodic porous media; however, the problem ofabrupt changes in the structure of a porous medium is not considered.Roman Letters A interfacial area of the - interface contained within the macroscopic system, m² - A _e area of entrances and exits for the -phase contained within the macroscopic system, m² - A interfacial area of the - interface contained within the averaging volume, m² - A ^* interfacial area of the - interface contained within a unit cell, m² - Ae area of entrances and exits for the -phase contained within a unit cell, m² - B second order tensor used to represent the velocity deviation (see Equation (3.30)) - b vector used to represent the pressure deviation (see Equation (3.31)), m^–1 - d distance between two points at which the pressure is measured, m - g gravity vector, m/s² - K Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the -phase (see Figure 2), m - characteristic length scale for the -phase (see Figure 2), m - n unit normal vector pointing from the -phase toward the -phase (n =–n ) - n _e unit normal vector for the entrances and exits of the -phase contained within a unit cell - p pressure in the -phase, N/m² - p intrinsic phase average pressure for the -phase, N/m² - p –p , spatial deviation of the pressure in the -phase, N/m² - r ₀ radius of the averaging volume and radius of a capillary tube, m - v velocity vector for the -phase, m/s - v phase average velocity vector for the -phase, m/s - v intrinsic phase average velocity vector for the -phase, m/s - v –v , spatial deviation of the velocity vector for the -phase, m/s - V averaging volume, m³ - V volume of the -phase contained within the averaging volume, m³ Greek Letters V/V, volume fraction of the -phase - mass density of the -phase, kg/m³ - viscosity of the -phase, Nt/m² - arbitrary function used in the representation of the velocity deviation (see Equations (3.11) and (B1)), m/s - arbitrary function used in the representation of the pressure deviation (see Equations (3.12) and (B2)), s^–1     

Experimental investigation of the creeping motion of a drop in a vertical tube

New experimental data regarding the motion of a drop along the axis of a vertical tube, filled with another highly viscous liquid, are obtained. The experiments are realised with sufficiently large drops for an internal circulation to develop and also for different pairs of fluids; the preponderant role of the gravity on the drop shape and consequently on its terminal velocity is pointed out. Moreover, by means of a visualization technique, details on the flow both inside and outside the drop are given.List of symbols g gravity acceleration - r distance from the drop center - R equivalent radius of the drop, i.e. the radius of the sphere having the same volume as the drop - R _EQ radius of the equatorial section of the drop - R _T tube radius - L _AX half length of the drop - U ₀ terminal velocity of the drop - P _s Poiseuille number= U _{0 e} /4 g R ² - Fr Fronde number = U ₀ ² _e /2 g R - Re Reynolds number = 2 U ₀ R _e / _e - E _o Eötvös number = 4g R ²/ - deformation parameter = _e U ₀/ - apparent density of the suspended liquid= | _i – _e | - _i viscosity of the suspended liquid - _e viscosity of the suspending liquid - drop-to-tube radius ratio = R/R _T - _EQ equatorial drop-to-tube radius ratio = R EQ/R _T - interfacial tension     

Transport in ordered and disordered porous media IV: Computer generated porous media for three-dimensional systems

In the method of volume averaging, the difference between ordered and disordered porous media appears at two distinct points in the analysis, i.e. in the process of spatial smoothing and in the closure problem. In theclosure problem, the use of spatially periodic boundary conditions isconsistent with ordered porous media and the fields under consideration when the length-scale constraint,r ₀L is satisfied. For disordered porous media, spatially periodic boundary conditions are an approximation in need of further study.In theprocess of spatial smoothing, average quantities must be removed from area and volume integrals in order to extractlocal transport equations fromnonlocal equations. This leads to a series of geometrical integrals that need to be evaluated. In Part II we indicated that these integrals were constants for ordered porous media provided that the weighting function used in the averaging process contained thecellular average. We also indicated that these integrals were constrained by certain order of magnitude estimates for disordered porous media. In this paper we verify these characteristics of the geometrical integrals, and we examine their values for pseudo-periodic and uniformly random systems through the use of computer generated porous media.

Nomenclature

Roman Letters A interfacial area of the- interface associated with the local closure problem, m² - A _e area of entrances and exits for the-phase contained within the averaging system, m² - a _i i=1, 2, 3 gaussian probability distribution used to locate the position of particles - I unit tensor - L general characteristic length for volume averaged quantities, m - L characteristic length for , m - L characteristic length for , m - characteristic length for the -phase particles, m - ⁰ reference characteristic length for the-phase particles, m - characteristic length for the-phase, m - _i i=1, 2, 3 lattice vectors, m - m convolution product weighting function - m _v special convolution product weighting function associated with the traditional volume average - n _i i=1, 2, 3 integers used to locate the position of particles - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - r _p position vector locating the centroid of a particle, m - r gaussian probability distribution used to determine the size of a particle, m - r ₀ characteristic length of an averaging region, m - r position vector, m - r _m support of the weighting functionm, m - averaging volume, m³ - V volume of the-phase contained in the averaging volume,, m³ - x positional vector locating the centroid of an averaging volume, m - x ₀ reference position vector associated with the centroid of an averaging volume, m - y position vector locating points relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - /L, small parameter in the method of spatial homogenization - standard deviation ofa _i - _r standard deviation ofr - _r intrinsic phase average of      

The stokes problems for a conducting fluid with a suspension of particles

The Stokes problems of an incompressible, viscous, conducting fluid with embedded small spherical particles over an infinite plate, set into motion in its plane by impulse and by oscillation, in the presence of a transverse magnetic field, are studied. The velocities of the fluid and of the particles and the wall shear stress are obtained. The stress is found to increase due to the particles and the magnetic field, with the effect of the particles diminishing as the field strength is increased.Nomenclature H ₀ strength of the imposed magnetic field - k density ratio of particles to fluid (per unit volume of flow field) - m _e ² H ₀ ² / - t time - y co-ordinate normal to the plate - u fluid velocity - v particle velocity - _e magnetic permeability of the fluid - kinematic viscosity of the fluid - electric conductivity of the fluid - fluid density - particle relaxation time - frequency of oscillation of the plate     

An experimental study on vortex breakdown in a differentially-rotating cylindrical container

The vortex breakdown phenomenon in a closed cylindrical container with a rotating endwall disk was reproduced. Visualizations were performed to capture the prominent flow characteristics. The locations of the stagnation points of breakdown bubbles and the attendant global flow features were in excellent agreement with the preceding observations. Experiments were also carried out in a differentially-rotating cylindrical container in which the top endwall rotates at a relatively high angular velocity _t, and the bottom endwall and the sidewall rotate at a low angular velocity _sb. For a fixed cylinder aspect ratio, and for a given relative rotational Reynolds number based on the angular velocity difference _t–_sb, the flow behavior is examined as |_sb/_t| increases. For a co-rotation (_sb/_t>0), the breakdown bubble is located closer to the bottom endwall disk. However, for a counter-rotation (_sb/_t<0), the bubble is seen closer to the top endwall disk. For sufficiently large values of _sb, the bubble ceases to exist for both cases.     

Stability characteristics of condensate films

The linear stability theory is used to study stability characteristics of laminar condensate film flow down an arbitrarily inclined wall. A critical Reynolds number exists above which disturbances will be amplified. The magnitude of the critical Reynolds number is in all practical situations so small that a laminar gravity-induced condensate film can be expected to be unstable. Several stabilizing effects are acting on the film flow; at an inclined wall these effects are due to surface tension, gravity and condensation mass transfer.

---

Zusammenfassung Mit Hilfe der linearen Stabilitätstheorie werden die Stabilitätseigenschaften laminarer Kondensatfilme an einer geneigten Wand untersucht. Es zeigt sich, daß Kondensatfilme in jedem praktischen Fall ein unstabiles Verhalten aufweisen. Der stabilisierende Einfluß von Oberflächenspannung, Schwerkraft und Stoffübertragung durch Kondensation bewkkt jedoch, daß Störungen in bestimmten Wellenlängenbereichen gedämpft werden.

---

Nomenclature c=c^*/u₀ complex wave velocity, celerity, dimensionless - c^*=c _r ^* + i c _i ^* complex wave velocity, celerity, dimensional - c_p specific heat at constant pressure - g gravitational acceleration - h_fg latent heat - k thermal conductivity of liquid - p^* pressure - p=p^*/u₀ ² dimensionless pressure - Pe=Pr Re^* Peclet number - Pr Prandtl number - Re^*=u₀ / Reynolds number (defined with surface velocity) - S temperature perturbation amplitude - t^* time - t=t^* u₀/ dimensionless time - T temperature - T_s saturation temperature - T_w wall temperature - T=T_s-T_w temperature drop across liquid film - u^*, v^* velocity components - u=u^*/u₀ dimensionless velocity components - v=v^*/u₀ dimensionless velocity components - u₀ surface velocity of undisturbed film flow - v _g ^* vapor velocity - x^*, y^* coordinates - x=x^*/ dimensionless coordinates - y=y^*/ dimensionless coordinates Greek Symbols =^* wave number, dimensionless - ^*=2 /^* wave number dimensional - ^* wave length, dimensional - =^*/ wave length, dimensionless - local thickness of undisturbed condensate film - kinematic viscosity, liquid - density, liquid - _g density vapor - surface tension - = (1 +) film thickness of disturbed film, Fig. 1 - stream function perturbation amplitude - angle of inclination Base flow quantities are denoted by^–, disturbance quantities are denoted by.     

Peristaltic pumping of a second-order fluid in a planar channel

The peristaltic motion of a non-Newtonian fluid represented by the constitutive equation for a second-order fluid was studied for the case of a planar channel with harmonically undulating extensible walls. A perturbation series for the parameter ( half-width of channel/wave length) obtained explicit terms of 0(²), 0(²Re²) and 0(₁Re²) respectively representing curvature, inertia and the non-Newtonian character of the fluid. Numerical computations were performed and compared to the perturbation analysis in order to determine the range of validity of the terms.Presented at the second conference Recent Developments in Structured Continua, May 23–25, 1990, in Sherbrooke, Québec, Canada     

The very slow flow of a Powell-Eyring fluid around a sphere

Summary The very slow flow of a Powell-Eyring type non-Newtonian fluid around a sphere is investigated by a variational technique. The result, a correction factor that is applied to the Stokes' equation, is given as a plot and as an equation which is empirically fit to the plot. Also, a comparison of the very slow flows of a simplified viscoelastic Oldroyd fluid and the Powell-Eyring fluid is made which indicates that in a certain restricted region of the very slow flows, both models give essentially the same results. The Oldroyd and Powell-Eyring model parameters are interrelated by forcing both models to fit the same tube flow viscosity data.Nomenclature B dimensionless quantity, v /R - C dimensionless second invariant - c ₁ constant determined by variational method - D dimensionless variational integral - D _2j , D _j+k position-independent variables used in specification of trial functions - E _2j , E _j+k position-independent variables used in specification of trial functions - f friction factor - f _corr friction factor correction - F _drag drag force on sphere - g, g ₀, g ₁ general trial function; first and second terms in the general trial function - G, H terms in the expression for C - j index - J variational integral - k index - K term in the expression for C - p, q integers - r integer, radial coordinate - R radius of sphere - Re Reynolds number - Re ₀ Reynolds number at point of zero shear rate - Re Reynolds number at infinite distance from sphere - Re _NN Reynolds number based on variable part of viscosity - u, v dimensionless position coordinates - V volume considered - v _i ith velocity component - v _r , v , v _z velocity components in the r, , and z-directions - v approach velocity of the fluid - x/ parameter in Powell-Eyring model - x _i i-position coordinate - parameter in Powell-Eyring model - rate of deformation - , _c , _N , ₀ coefficient of viscosity; cross viscosity; parameter in Powell-Eyring model; viscosity in limit of zero shear rate - spherical coordinate - , _ij rate of deformation tensor; ij-component of rate of deformation tensor - ₁, ₂ parameters in Oldroyd model - Newtonian viscosity - ₁, ₂ parameters in Oldroyd model - dimensionless radial coordinate, r/R - second invariant - fluid density - spherical coordinate - stream function     

Flow about a circular cylinder with a single large-scale surface perturbation

An experimental study of the flow around a cylinder with a single straight perturbation was conducted in a wind tunnel. With this bluff body, positioned in a uniform crossflow, the vortex shedding frequency and other flow characteristics could be manipulated.The Strouhal number has been shown to be a function of the perturbation angular position, _p , as well as the perturbation size and Reynolds number. As much as a 50% change in Strouhal number could be achieved, simply by changing _p by 1°. The perturbation size compared to the local boundary layer thickness, , was varied from approximately 1 to about 20 . The Reynolds number was varied from 10,000 to 40,000. For perturbation sizes approximately 5 to 20 and Reynolds numbers of 20,000 to 40,000, a consistent Strouhal number variation with _p was observed.A detailed investigation of the characteristic Strouhal number variation has shown that varying _p had a significant influence on the boundary layer separation and transition to turbulence. These significant changes occurring in the boundary layer have been shown to cause variations in the spacing between the shear layers, base pressure, drag, lift, and the longitudinal spacing between the vortices in the vortex street.List of Symbols a longitudinal spacing of vortices in the vortex street - C _d drag coefficient - C _dc drag coefficient corrected for blockage effect - C _l lift coefficient - C _p pressure coefficient, p _i –p /q - C _pb base pressure coefficient - C _pbc base pressure coefficient corrected for blockage effect - d perturbation diameter - d ^* spacing between the shear layers; defined as conditionally averaged spacing between points in the shear layers corresponding to 0.99u _max/U - D cylinder diameter; diameter of the circumscribing circle for a cable - f _v vortex shedding frequency - H wind tunnel test section cross-sectional width - L spanwise length of the cylinder - p _i tap pressure - p free stream static pressure - q free stream dynamic pressure - Re Reynolds number based on cylinder diameter - rms root-mean-square - S Strouhal number, f _v D/U - S _max maximum value of S - S _min minimum value of S - t time - u _c vortex convection velocity - u _max maximum velocity in the shear layer - U free stream velocity - U _c free stream velocity, corrected for blockage effect - x streamwise dimension referenced from the back of the cylinder - z lateral wake dimension, i.e., perpendicular to the free stream velocity vector and cylinder axis, referenced from the cylinder axis - x spacing between two hot wire probes aligned streamwise - phase difference between two hot wire probes aligned streamwise - boundary layer thickness - angle from stagnation point in degrees - _p perturbation angular position - _{b p} where S drops back to about the S of a cylinder - _c critical angle, angular position where S drops steeply with 1° change in - _{m p} where S was minimum - _{r p} after S recovers from drop in value - _{t p} where S starts to increase from about the S of a cylinder