Non-extraction flow injection determination of cationic surfactants using eriochrome black-T

A new, rapid, sensitive, non-extraction batch, and flow injection spectrophotometric method for the determination of cationic surfactants (CSs) such as cetyltrimethyl ammonium bromide (CTAB), tetra-n-butyl ammonium chloride (TBAC) and cetylpyridinium chloride (CPC) is proposed. The method is based on the interaction of cationic surfactants with eriochrome black-T to form an ion-association complex. This complex has strong absorbance at 708 nm. The effects of chemical parameters and FIA variables on the determination of cationic surfactants were studied in detail, especially for CTAB. Under optimum conditions, the two linear calibration ranges of the method are 3.0 × 10⁻⁶ to 5.0 × 10⁻³ mol L⁻¹ CTAB, CPB and DTAB for the batch spectrophotometric method and 2.0 × 10⁻⁶ to 2.0 × 10⁻⁴ mol L⁻¹ CTAB, CPB and TBC for the flow injection spectrophotometric method. The sample throughput was 35 ± 5 samples h⁻¹ at room temperature. The relative standard deviations for 10 replicates of analysis of (2.0, 0.6 and 0.2) × 10⁻⁴ mol L⁻¹ CTAB were 1.2, 1.3, and 0.8%, respectively. In addition, the influence of potential interfering substances on the determination of cationic surfactants was studied. The proposed method is simple and rapid, using no toxic organic solvents. It was applied to the determination of trace CS in industrial wastewater with satisfactory results.     

Application of a Glassy Carbon Electrode Modified with Poly(Glutamic Acid) in Caffeic Acid Determination

Glassy carbon electrodes were coated with films of poly(glutamic acid) (PG), and the modified electrode proved to be very effective in the oxidation of caffeic acid. The performance of the film was also tested with ascorbic acid, coumaric acid, ferulic acid, sinapic acid and chlorogenic acid. At pH 5.6, all the hydroxycinnamic acids yield a higher peak current intensity when oxidized after incorporation in the PG-modified electrode, and only the oxidation of ascorbic acid exhibits overpotential reduction. At pH 3.5 only caffeic and chlorogenic acid are incorporated in the modified electrode and exhibit a well-defined oxidation wave at +0.51 V and +0.48 V, which is the base for their determination. Linear calibration graphs were obtained from 9 × 10⁻⁶ mol L⁻¹ to 4 × 10⁻⁵ mol L⁻¹ caffeic acid by linear voltammetric scan and from 4 × 10⁻⁶ mol L⁻¹ to 3 × 10⁻⁵ mol L⁻¹ by square wave voltammetric scan. The method was successfully applied to the determination of caffeic acid in red wine samples without interference from other hydroxycinnamic acids or ascorbic acid.     

Fluorescence enhancement effect for the determination of DNA with calcein-cetyl trimethyl ammonium bromide system

A new spectrofluorimetric method was developed for the determination of trace amounts of DNA using the calcein as a fluorescent probe. In the presence of appropriate amounts of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB), the anionic dye calcein dimerizes. The weak fluorescence intensity of the dimer was enhanced by adding DNA at pH 6–7. The interaction between calcein–CTAB and DNA was studied on the basis of this behavior and a new method was developed for determining DNA. Under the optimal conditions, the enhanced fluorescence intensity was in proportion to the concentration of DNA in the range of 4.0 × 10⁻⁶ to 8.0 × 10⁻⁵ g L⁻¹ for fsDNA and thermally denatured ctDNA (4.5 × 10⁻⁶ to 9.0 × 10⁻⁵ g L⁻¹). The detection limits (S/N = 3) were 2.0 × 10⁻⁶ and 2.2 × 10⁻⁶ g L⁻¹, respectively. This method was used for determining the concentration of DNA in synthetic samples with satisfactory results.     

Potentiometric Membrane Sensor for Determination of Saccharin

A potentiometric poly(vinyl chloride) membrane sensor for determination of saccharin is described. It is based on the use of Aliquat 336S-saccharinateion-pair as an electroactive material in plasticized PVC membranes with o-nitrophenyloctylether or dioctylphthalate. The sensor is conditioned for at least two days in 0.1 mol L⁻¹ sodium saccharinate before use. It exhibits fast, stable and Nernstian response for saccharinate ions over the concentration range of 1.0 × 10⁻¹–5.0 × 10⁻⁵ mol L⁻¹ and pH range of 4.5–11. The sensor is used for determination of saccharin in some dosage forms. Results with an average recovery of 101% and a mean standard deviation of 0.2% are obtained which is compared favourably with data obtained using the British pharmacopoeia method. The sensor shows reasonable selectivity towards saccharin in presence of many anions and natural sweeteners.     

Electrocatalytic Oxidation and Direct Determination of L-Tyrosine by Square Wave Voltammetry at Multi-wall Carbon Nanotubes Modified Glassy Carbon Electrodes

The electrochemical behavior of L-tyrosine was investigated at a multi-wall carbon nanotubes modified glassy carbon electrode. L-tyrosine itself showed a poor electrochemical response at the bare glassy carbon electrode; however, a multi-wall carbon nanotubes film fabricated on the glassy carbon electrode can directly enhance the electrochemical signal of L-tyrosine when applying cyclic voltammetry and square wave stripping voltammetry without any mediator. Cyclic voltammetry was carried out to study the electrochemical oxidation mechanism of L-tyrosine, which shows a totally irreversible process and an oxidation potential of 671 mV at the modified electrode and 728 mV at the bare electrode, ΔE_p = 57 mV. The anodic peak current linearly increases with the square root of scan rate in the low range, suggesting that the oxidation of L-tyrosine on the multi-wall carbon nanotubes modified electrode is a diffusion-controlled process. The square wave stripping voltammetry currents of L-tyrosine at the multi-wall carbon nanotubes modified electrodes increased linearly with the concentration in the range of 2.0 × 10⁻⁶–5.0 × 10⁻⁴ mol L⁻¹. The detection limit was 4.0 × 10⁻⁷ mol L⁻¹. The method is simple, quick, sensitive and accurate.     

Luminescent CuS nanotubes as silver ion probes

CuS nanotubes (NTs) made up of nanoparticles were successfully prepared in large quantities in an O/W microemulsion system under low temperature. Based on the characteristics of synchronous fluorescence spectroscopy (SFS), a new method with high sensitivity and selectivity was developed for rapid determination of silver ion with functional copper sulphide (CuS) nanotubes as a fluorescence probe. Under optimal conditions, functional copper sulphide displayed a calibration response for silver ion over a wide concentration range from 1.0 × 10⁻¹⁰ to 1.0 × 10⁻⁸ mol L⁻¹. The limit of detection was 0.5 × 10⁻¹⁰ mol L⁻¹ and the relative standard deviation of eight replicate measurements for the highest concentration (1 × 10⁻⁸ mol L⁻¹) was 3%. Compared with several fluorescence methods, the proposed method had a wider linear range and improved the sensitivity. Furthermore, the concentration dependence of the synchronous fluorescence intensity is effectively described by a Langmuir-type binding isotherm.     

Electrochemical characterization of cationic surfactants’ adsorption on a disturbed n-alkanethiolate self-assembled monolayer-modified polycrystalline gold electrode

The adsorption of cetyltrimethylammonium bromide (CTAB) on disturbed n-alkanethiolate self-assembled monolayers (SAMs) was investigated by electrochemical methods with potassium ferricyanide [K₃Fe(CN)₆] as a probe. Compared with the completely restrained signal at ordinary compact n-alkanethiolate SAMs, the electrochemical response of K₃Fe(CN)₆ at the disturbed n-alkanethiolate SAMs was partly restored and became progressively reversible in the presence of increasing concentrations of CTAB, which was employed to characterize the adsorption of cationic surfactants on hydrophobic SAMs. The effect of CTAB concentration on electrochemical impedance spectroscopy (EIS) plots indicated that CTAB experienced two different types of adsorptive behavior at the disturbed n-alkanethiolate SAMs: monomer adsorption at low concentrations below 1×10^–6 M and monolayer adsorption at CTAB concentrations above 1×10^–5 M. The adsorption of a series of cationic surfactants with similar structures to CTAB on disturbed n-alkanethiolate SAMs was also explored. These surfactants had similar adsorptive behavior and showed nearly linear adsorption characteristics with the length of their hydrophobic tails.     

Study on the fluorescence system Be-rutin-SDS-Triton X-100 and the determination of rutin

Summary It was found that rutin forms a fluorescent complex with Be²⁺, the fluorescence intensity of which can be increased thirty-one times in a mixed medium of sodium dodecyl sulfonate (SDS) and Triton X-100. A linear relationship is obtained between the fluorescence intensity and the rutin concentration in the range of 1.2×10^–6 to 4.8×10^–5 mol·l^–1. The detection limit is 5.9×10^–7 mol·l^–1. Rutin traces were determined in drugs using the standard addition method. The luminescence mechanism of the system is discussed.     

Influence of the surfactant bromide of cetyltrimetyl ammonium in the determination of chlorogenic acid in instant coffee and mate tea samples

In this study, two quantitative differential-pulse polarography (DPP) and square-wave voltammetry (SWV) methods were developed to determine total chlorogenic acid (CGA). Studies on this compound involve its reduction at a hanging mercury drop electrode in micellar media—a simple, fast, reliable, and sensitive method. The use of surfactant cationic cetyltrimethylammonium bromide (CTAB) was pivotal to the development of these methods, allowing for satisfactory changes in CGA reduction. The supporting electrolyte which provided the best-defined CGA determination was 0.04-mol L⁻¹ phosphate buffer at pH 6.0 in the presence of CTAB. Based on this use and under optimized conditions, the two new DPP and SWV methods for CGA analysis had detection limits of 2.36 × 10⁻⁷ and 1.34 × 10⁻⁹ mol L⁻¹, respectively, for a pure standard. Analysis of the standard in the presence of treated instant coffee and mate tea samples allowed for good average recovery rates, ranging from 97.06% to 105.90%.     

Flow injection determination of cationic surfactants by using N-bromosuccinimide and N-chlorosuccinimide as new oxidizing agents for luminol chemiluminescence

Two highly sensitive chemiluminescence (CL) systems are described. The method is based on the CL generated during the oxidation of luminol by N-bromosuccinimide (NBS) and N-chlorosuccinimide (NCS) in alkaline medium. The emission intensity is reduced by the presence of some surfactants at concentrations lower than critical micelle concentration (cmc).A new, simple, rapid and selective flow injection CL method for the determination of cationic surfactants such as dodecyltrimethylammonium bromide (DTAB), cetyltrimethylammonium bromide (CTAB) and cetylpyridinium chloride (CPC) is proposed. Their determinations are based on the reducing effect on the emission intensity of NBS-luminol and NCS-luminol chemiluminescent reactions. The effect of analytical and flow injection analysis (FIA) variables on these CL systems and on the determination of the cationic surfactants are discussed. The optimum parameters for the determination of cationic surfactants were studied and were found to be the following: luminol, 1×10⁻⁶ M; NBS and NCS both, 5×10⁻² M; NaOH, 5×10⁻² M and flow rate, 3.5 ml min⁻¹.     

Determination of trace europium by use of the new fluorescence system europium–sparfloxacin–1,10-phenanthroline–sodium dodecyl sulfate

A new lanthanide-sensitized luminescence system: europium–sparfloxacin–1,10-phenanthroline–sodium dodecyl sulfate has been discovered. The spectrofluorimetric properties of the system were studied. The effect of experimental conditions on the fluorescence intensity was defined. Under the optimum conditions, the fluorescence intensity of the system is a linear function of the concentration of europium in the range 5.0×10^–9–1.0×10^–6 mol L^–1 and the detection limit is 1.0×10^–10 mol L^–1. The system was used for the determination of trace amounts of europium in rare earth samples with satisfactory results.     

Simultaneous determination of hydroquinone and catechol at PASA/MWNTs composite film modified glassy carbon electrode

A poly-amidosulfonic acid and multi-wall carbon nanotubes composite (PASA/MWNTs) modified electrode has been constructed by electropolymerization on glassy carbon electrode (GCE). The electrochemical behaviors of hydroquinone (HQ) and catechol (CC) were investigated using cyclic and differential pulse voltammetries (DPVs) at the prepared electrode. Separation of the reductive peak potentials for HQ and CC was about 120 mV in pH 6.0 phosphate buffer solution (PBS), which makes it suitable for simultaneous determination of these compounds. In the presence of 1.0 × 10⁻⁴ mol L⁻¹ isomer, the reductive peak currents of DPV are proportional to the concentration of HQ in the range of 6.0 × 10⁻⁶ to 4.0 × 10⁻⁴ mol L⁻¹, and to that of CC in the range of 6.0 × 10⁻⁶ to 7.0 × 10⁻⁴ mol L⁻¹. When simultaneously changing the concentration of both HQ and CC, the linear concentration range of HQ (or CC) is 6.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ (or 6.0 × 10⁻⁶ to 1.8 × 10⁻⁴ mol L⁻¹), and the corresponding detection limits are 1.0 × 10⁻⁶ mol L⁻¹. The proposed method has been applied to simultaneous determination of HQ and catechol in water sample, and the results are satisfactory.     

The New Fluorescence Enhancement System Eu<Superscript>3+</Superscript>-ARADE-HMTM-Al<Superscript>3+</Superscript> and its Analytical Application

A new bis-Schiff base ligand, N,N-bis-(4-N-aminothiourea-2-amylidene)-4,4-diaminodiphenyl ether (ARADE), was synthesized. Its complex with Eu³⁺ in DMF emits the intrinsic fluorescence of Eu³⁺. The fluorescence intensity of the Eu³⁺-ARADE system was enhanced about 60-fold by the addition of hexamethylene tetramine (HMTM) and potash alum. This is a new fluorescence enhancement phenomenon. The excitation and emission wavelengths are 375nm and 615nm, respectively. Under optimal conditions, the fluorescence intensities vary linearly with the concentration of Eu³⁺ in the range of 7.8×10^–9–1.75×10^–5mol·L^–1 with a detection limit of 5.2×10^–9mol·L^–1, or with the concentration of Al³⁺ in the range of 3.1×10^–7–9.7×10^–5mol·L^–1 with a detection limit of 2.7×10^–7mol·L^–1. The interferences of some rare earth metals and other inorganic ions were described. This method was applied to the determination of Eu³⁺ in high purity yttrium oxide and the analysis of Al³⁺ in alloy steel standard samples. The mechanism of fluorescence enhancement was also studied.     

Synthesis and characterization of the water-soluble silica-coated ZnS:Mn nanoparticles as fluorescent sensor for Cu ions

Silica-coated ZnS:Mn nanoparticles were synthesized by coating hydrophobic ZnS:Mn nanoparticles with silica shell through microemulsion. The core–shell structural nanoparticles were confirmed by X-ray diffraction (XRD) patterns, high-resolution transmission electron microscope (HRTEM) images and energy dispersive spectroscopy (EDS) measurements. Results show that each core–shell nanoparticle contains single ZnS:Mn nanoparticle within monodisperse silica nanospheres (40 nm). Photoluminescence (PL) spectroscopy and UV–vis spectrum were used to investigate the optical properties of the nanoparticles. Compared to uncoated ZnS:Mn nanoparticles, the silica-coated ZnS:Mn nanoparticles have the improved PL intensity as well as good photostability. The obtained silica-coated ZnS:Mn nanoparticles are water-soluble and have fluorescence sensitivity to Cu²⁺ ions. Quenching of fluorescence intensity of the silica-coated nanoparticles allows the detection of Cu²⁺ concentrations as low as 7.3 × 10⁻⁹ mol L⁻¹, thus affording a very sensitive detection system for this chemical species. The possible quenching mechanism is discussed.     

Bifunctional sensor of nitric oxide and oxygen based on hematite nanotubes embedded in chitosan matrix

A novel hybrid bifunctional sensing platform for simultaneous determination of NO and O₂ has been developed, whereby hematite nanotubes are immobilized into the chitosan matrix onto a gold electrode (labeled as HeNTs-Chi/Au). The HeNTs distributed in porous-structured chitosan matrix not only offer abundant active sites for bifunctional sensing of NO and O₂, but also facilitate oxidation of NO and reduction of O₂ dramatically. Straight calibration curves are achieved in analyte concentration ranges of 5.0 × 10⁻⁸ to 1.25 × 10⁻⁶ mol L⁻¹ for NO and 2.5 × 10⁻⁷ to 6.0 × 10⁻⁶ mol L⁻¹ for O₂. Also, the detection limits are low of 8.0 × 10⁻⁹ mol L⁻¹ for NO and 5.0 × 10⁻⁸ mol L⁻¹ for O₂. Such an efficient bifunctional sensor for NO and O₂ offers great potential in quantitation of NO levels in biological and medical systems, since NO level is highly regulated by various reactive oxygen species.     

Micro-pumping flow system for spectrophotometric determination of anionic surfactants in water

A novel procedure has been developed for spectrophotometric determination of anionic surfactants in water using a solenoid micro-pump as fluid-propulsion device. The proposed method is based on substitution of methyl orange (MO) by anionic surfactants in the formation of an ion-pair with the cetyl pyridine ion (CPC⁺) at pH 5.0. The flow network comprised four solenoid micro-pumps which, under microcomputer control, enabled sample and reagent introduction, and homogenisation in the reaction zone. The system is flexible and simple to operate and control, and sensitive and precise. The analytical plot for the anionic surfactant was linear between 1.43×10^–6 and 1.43×10^–5 mol L^–1 (0.5 to 5.0 mg L^–1; R=0.997, n=5). The relative standard deviation was 0.8% (n=11) for a sample containing 5.74×10^–6 mol L^–1 (2 mg L^–1) surfactant. The limit of detection was 9.76×10^–8 mol L^–1 (0.034 mg L^–1) and the sampling throughput was 60 determinations per hour. The results obtained for washing-water samples were comparable with those obtained by use of the reference method, and no significant differences at the 95% confidence level were observed.     

Novel lipoate-selective membrane sensor for the flow injection determination of alpha-lipoic acid in pharmaceutical preparations and urine

A potentiometric lipoate-selective sensor based on mercuric lipoate ion-pair as a membrane carrier is reported. The electrode was prepared by coating the membrane solution containing PVC, plasticizer, and carrier on the surface of graphite electrode. Influences of the membrane composition, pH, and possible interfering anions were investigated on the response properties of the electrode. The sensor exhibits significantly enhanced response toward lipoate ions over the concentration range 1 × 10⁻⁷ mol L⁻¹ to 1 × 10⁻² mol L⁻¹ with a lower detection limit of (LDL) of 9 × 10⁻⁸ mol L⁻¹ and a slope of −29.4 mV decade⁻¹, with S.D. of the slope is 0.214 mV. Fast and stable response, good reproducibility, long-term stability, applicability over a pH range of 8.0–9.5 is demonstrated. The sensor has a response time of ≤12 s and can be used for at least 6 weeks without any considerable divergence in its potential response. The proposed electrode shows good discrimination of lipoate from several inorganic and organic anions. The CGE was used in flow injection potentiometry (FIP) and resulted in well defined peaks for lipoate ions with stable baseline, excellent reproducibility and reasonable sampling rate of 30 injections per hour. The proposed sensor has been applied for the direct and FI potentiometric determination of LA in pharmaceutical preparations and urine; and has been also utilized as an indicator electrode for the potentiometric titration of LA.     

Studies on Intramolecular Charge Transfer Fluorescence Probe and DNA Binding Characteristics

An intramolecular charge transfer fluorescence probe of 4′-N,N-dimethylamino-4-amino-chalcone(DMAC) exhibits characteristics clearly correlated with the polarity of solvents. The interaction of this fluorescence probe with calf thymus DNA has been investigated. Generally, DMAC bound to DNA shows marked changes in fluorescence and absorbance properties compared to the spectral characteristics of the free form in solution phase. In the presence of DNA the fluorescence intensity of DMAC is greatly increased with a large bathochromic shift of excitation and emission wavelengths. A hypochromism in absorption spectrum was also observed. The absorption and fluorescence spectra, salt concentration effect, and KI quenching experiments demonstrate that DMAC molecule as an intercalator is inserted into the base-stacking domain of DNA double helix, and the interaction of the nucleobases with DMAC molecule causes the increase of fluorescence intensity and hypochromism in absorption spectrum. The intrinsic binding constant and the binding site number were estimated to be 7.04 × 10⁶ mol L⁻¹ in base pairs and 0.065, respectively. The I/I₀ vs DNA concentration plot shows a linear range covering 1.98 × 10⁻⁶ to 2.08 × 10⁻⁴ mol L⁻¹ in base pairs which can be used for determining DNA with a detection limit of 6.0 × 10⁻⁷ mol L⁻¹ in base pairs (0.6 μg ml⁻¹).     

Fluorescence-detecting cationic surfactants using luminescent CdTe quantum dots as probes

A novel fluorescence quenching method for the determination of cationic surfactants (CS), specifically cetyltrimethylammonium bromide (CTAB), dodecyltrimethylammonium bromide (DTAB), and cetylpyridinium chloride (CPC), has been developed using water-soluble luminescent CdTe quantum dots (QDs) modified with thioglycolic acid (TGA). The possible interference from heavy and transition metals (HTM) has been efficiently eliminated through simple sample treatment with mercapto cotton made in-house. Under optimum conditions, the extent of fluorescence quenching of CdTe QDs is linearly proportional to the concentration of CS from 2.0 × 10⁻⁷ to 7.0 × 10⁻⁶ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁸ mol L⁻¹. The relative standard deviation for 1.0 × 10⁻⁶ mol L⁻¹ CTAB is 2.5% (n = 6). The proposed method exhibits high sensitivity and selectivity and furthermore avoided the use of toxic organic solvents and tedious solvent extraction procedures. It has been applied to the determination of trace CS in natural river water and commodity samples with satisfactory results. Potential interference from heavy and transition metals is eliminated during photoluminescence detection of CS through simple sample pre-treatment with mercapto cotton     

Electrochemical Behavior and Determination of Uric Acid at Single-Walled Carbon Nanotube Modified Gold Electrodes

The voltammetric behavior of uric acid was studied at a single-walled carbon nanotube (SWNT) modified gold electrode. Uric acid can effectively accumulate at this electrode and produce an anodic peak at about 0.45 V (vs. SCE) in pH 5.0 sodium acetate buffer solutions (HAc-NaAc). The experimental parameters, such as solution pH, accumulation time, and amount of SWNT, were optimized for determination. Under the optimum conditions, the anodic peak current is linear to the uric acid concentration over the range of 1.0×10⁻⁷ M to 2.5×10⁻⁵ M with a correlation coefficient of 0.998. The detection limit was 5.0×10⁻⁸ M for 60 s accumulation. The electrode could be easily regenerated and exhibited good stability. A 5.0×10⁻⁶ M uric acid solution was measured ten times using the same electrode, and the relative standard deviation of the peak current was 1.3%. This method was successfully applied to the determination of uric acid in human urine samples, and the recovery was 97–99%. The feasibility for simultaneous determination of xanthine, ascorbic acid and uric acid was discussed. These species did not interfere with each other in a certain concentration range. The influence of some surfactants on the anodic peak was also examined.