An interface chip connection between capillary electrophoresis and thermal lens microscope

A thermal lens microscope (TLM) detection of capillary electrophoresis (CE) utilizing microchip technology was developed. Fused-silica capillaries with an inner diameter of 50 microm were directly connected to a microchannel in a microchip. The detection limit by TLM was estimated as 2.8 x 10(-7) absorbance by measuring pure water. The detection limit of derivatized amino acids determined by CE-TLM was estimated as 2.4 x 10(-8) M, which was 100 times lower than that of conventional absorbance detection.     

Determination of copper with neocuproine by thermal-lens spectrometry

Conditions for the spectrophotometric determination of copper with 2,9-dimethyl-l,10-phenan-throline (neocuproine) in the presence of ascorbic acid in a water-ethanol solution (9 : 1) at pH 4.5–5.0 have been found. The detection limit is 3 x 10^-6 M. The concentration range is from 4.4 x 10^-6 to 3 x 10^-4 M. Conditions for the determination of copper(I) with neocuproine by thermal lens spectrometry have been proposed. The detection limit is 4 x 10^-7 M. The concentration range is from 7 x 10^-7 to 6 x 10^-5 M. Iron(II) at concentrations as high asn x 10^-4 M does not interfere with the determination of copper. Changes in the conditions for the photometric reaction associated with passing from spectrophotometric measurements to thermal lensing are discussed.     

Violet light emitting diode-induced fluorescence detection combined with on-line sample concentration techniques for use in capillary electrophoresis

The first application of a violet light-emitting diode (LED) for fluorescence detection in capillary electrophoresis (CE) is described. The utility of violet LED (peak emission wavelength at 410 nm, approximately 2 mW) for fluorescence detection is demonstrated by examining reserpine and dopamine-labeled NDA (naphthalene-2,3-dicarboxaldehyde), respectively. The detection limit for reserpine was determined to be 2.5 x 10(-6) M by normal micellar electrokinetic capillary chromatography (MEKC) and this was improved to 2.0 x 10(-9) M and 2.0 x 10(-10) M when sweeping-MEKC and cation-selective exhaustive injection (CSEI)-sweep-MEKC techniques were applied, respectively. In addition, the detection limit of NDA-labeled dopamine was determined to be 6.3 x 10(-6) M by means of normal MEKC and this was improved to 3.0 x 10(-8) M when the sweeping-MEKC mode was applied.     

Integration of a wet analysis system on a glass chip: determination of Co(ii) as 2-nitroso-1-naphthol chelates by solvent extraction and thermal lens microscopy

The integration of a wet analysis system on a glass chip was demonstrated and determination of Co(II) was performed using this system. The Co(II) was extracted into m-xylene from aqueous solution as 2-nitroso-1-naphthol chelates, and colorimetric determination of the m-xylene phase was applied by a thermal lens microscope. The integration of the chemical operation procedures shown here leads to a considerable reduction in analyzing time. The time for extraction in the integrated system, 10 min, was about tenfold shorter than a conventional system using a separatory funnel and mechanical shaker. Moreover, troublesome operations such as phase separation necessary for the conventional system could be omitted. The determination of Co(II) in the range 2 x 10(-7)-1 x 10(-8) M, which was estimated to be 0.072-1.44 zmol, was achieved.     

A water-soluble fluorescent fluoride ion probe based on Alizarin Red S-Al(III) complex

A new water-soluble fluorescent fluoride ion signaling system has been developed based on the ligand exchange mechanism in aqueous medium. This procedure is based on the exchange of two Alizarin Red S (ARS) molecules coordinated to Al(III) by fluoride ion without interference from other common anions. The binary complex of ARS with Al(III) provides a sensitive signaling system for fluoride ion in the concentration range from 5x10(-6) to 3x10(-4) M. The ligand exchange reaction of ARS-Al(III) complex with fluoride ion has been investigated by UV-vis and fluorescence spectroscopies combined with the AM1 semi-empirical quantum chemical calculations. The pale orange fluorescence (lambdamax=575 nm) exhibited by the complex upon excitation at 435 nm decreases in intensity with fluoride addition with a detection limit of 0.1 mg L-1.     

Observations on photochemical fluorescence enhancement of the terbium(III)-sparfloxacin system.

Fluorescence of terbium(III) was sensitized when excited in the presence of sparfloxacin (SPFX) in the aqueous solution because a Tb(III)-SPFX complex was formed. The sensitized fluorescence was further enhanced when this system was exposed to 365 nm ultraviolet light. By the spectral properties and contrast experiments, it is proved that irradiation makes this system undergo photochemical reactions and a new terbium complex which is more favorable to the intramolecular energy transfer is formed. The mechanism of photochemical fluorescence enhancement of the Tb(III)-SPFX system is discussed and a new sensitive and selective photochemical fluorimetry for the determination of SPFX is established. Under the optimum conditions, the linear range is 1.0-50 x 10(-7) M for SPFX, the detection limit is 3.0 x 10(-9) M and the R.S.D. for 5.0 x 10(-7) M SPFX is 1.3% (n = 9). Without any pretreatment the recovery of SPFX in human urine was determined with satisfaction.     

Pesticide analysis by MEKC on a microchip with hydrodynamic injection from organic extract

An integrated microchip for monitoring carbamate pesticides in environmental water using continuous flow chemical processes is under development, i. e., the integration of hydrolysis, azo-derivatization, liquid-liquid extraction, electrophoretic separation, and quantification. The separation of the derivatives of four carbamate pesticides (carbaryl, carbofuran, propoxur, and bendiocarb) extracted in the continuous flow of a 1-butanol phase was studied in a silica microchip using micellar EKC. A baseline separation of four pesticide derivatives was achieved on a silica chip using hydrodynamic injection with electroosmotic gating. Detection using a thermal lens microscope showed good linearity in the concentration range of 10(-6 )-10(-5 )M with an LOD of 5 x 10(-7) M, which is superior to that of conventional CE with UV absorption detection at a level of 10(-4) M.     

Conventional and thermal lens spectrophotometric determination of p-aminobenzoic acid and arylamine diuretics previous azodye formation in a micellar medium

The determination of the diuretics hydrochlorothiazide, bendroflumethiazide and furosemide by both conventional and thermal lens spectrophotometry (TLS, 100 mW of pump power at 514.5 nm) following previous hydrolysis, diazotization and coupling with N-(naphthyl)ethylenedine (NED) in a sodium dodecyl sulphate (SDS) micellar medium of pH approximately 1 was studied. p-Aminobenzoic acid (PABA) was used as a model compound to optimize the derivatization procedures. 3-Substituted indoles, such as 5-hydroxyindole-3-acetic acid and tryptophan, gave N-nitroso derivatives which interfered with the determination of the diuretics in urine. The derivatized diuretics in urine were separated using HPLC with a Spherisorb ODS-2 C(18) column, and a 0.1M SDS mobile phase containing 5% n-propanol and 0.001M sodium dihydrogen phosphate (pH 3). The diuretics gave limits of detection (LODs) of ca. 5 x 10(-9)M for the TLS procedure. The LODs were 20-50-fold higher for the corresponding spectrophotometric procedure.     

Fluoride ion detection by 8-hydroxyquinoline-Zr(IV)-EDTA complex

A simple fluorescent detection based on the ligand exchange mechanism is proposed for the fluoride ion in aqueous media. This procedure is based on the exchange of 8-hydroxyquinoline (oxine) coordinated to Zr(IV) by fluoride ion without interference from other common anions. The ternary complex of oxine with [Zr(H(2)O)(2)EDTA].2H(2)O formed by replacing two water molecules in aqueous solution provides a sensitive signalling system for fluoride ion in the concentration range from 6 x 10(-7)M to 8 x 10(-4)M. The green fluorescence (lambda(max)=532 nm) exhibited by the complex upon excitation at 247 nm decreases in intensity with fluoride addition with a detection limit of 12 ppb. The complexation reaction between oxine and Zr(IV)-EDTA and the ligand exchange reaction with fluoride ion has been investigated by UV-vis and fluorescence spectroscopies combined with the PM3 semi-empirical quantum chemical calculations. Job's method of continuous variation and the molar ratio method ascertain a 1:1 stoichiometry composition of the chelate in aqueous media.     

Determination of aluminum in environmental and biological samples by reversed-phase high-performance liquid chromatography via pre-column complexation with morin

Morin was used as a pre-column reagent for the determination of aluminum by RP-HPLC with fluorescence detection. This method has been successfully applied to direct determination of trace Al in environmental and biological samples. The response was linear from 6 x 10(-9) to 6 x 10(-5) M with a detection limit of 2 x 10(-9) M. In addition, the different Al complexes with morin were separated by the proposed HPLC procedure and their coordination ratios were depicted by molar-ratio method. The results showed that 1:1 and 2:1 Al-morin complexes formed.     

Thermal lens detection device

A thermal lens detection device was developed to realize an easy-to-use, portable and sensitive detector for nonfluorescent molecules. Two laser diodes (658 nm for excitation and 785 nm for probe) were made coaxial in an optical unit and were coupled to a single-mode optical fiber. On a microfluidic chip, a small holder for the optical fiber was fixed, and micro-lenses (numerical aperture of 0.2) were also integrated inside the holder. The micro-lenses were designed to realize an adequate chromatic aberration (50 μm), which was essential for sensitive thermal lens detection. Compared with conventional thermal lens detection systems which required very laborious and accurate optical alignment with the microchannel, the new device needed just attachment-detachment of the optical fiber, which was important for practical application. The lower limit of detection was 10 nM for nickel(II) phthalocyaninetetrasulfonic acid tetrasodium salt solutions (model sample), and the absorbance was 9 × 10(-6) AU. The absolute number of molecules detected was less than 200 zmol. The coefficient of variance for 5-time attachment-detachment of the optical probe was as small as 3.6%. The technical development allowed integration of the thermal lens detection devices inside a microsystem (e.g. enzyme-linked immuno-sorbent assay system), and practical microsystems were realized with sensitivities several-orders higher than absorptiometry.     

Toward million-fold sensitivity enhancement by sweeping in capillary electrophoresis combined with thermal lens microscopic detection using an interface chip

This paper reports a thermal lens microscope (TLM) detection coupled with capillary electrophoresis (CE) by using an interface chip (IFChip) to achieve highly sensitive detection with high reproducibility. Fused silica capillaries with an inner diameter of 50 microm were directly connected to a microchannel on the IFChip. In comparison with an on-capillary detection method in CE-TLM, ca. 10-fold improvements in the reproducibility for peak height were obtained by using IFChips. The detection limit of an azo dye was estimated to be 3.6 x 10(-7)M (100 ppb), which was above 100-times lower than that of conventional absorbance detection. Toward further improvement of the detectability for nonfluorescent compounds, on-line sample preconcentration by sweeping was applied to the CE-TLM using the IFChip. Due to the sweeping effect, 3900000-fold increase in the sensitivity was successfully achieved.     

Optical photothermal detection in HPLC

A mode-mismatched parallel dual-beam thermal lens spectrometer with a far-field single-channel detector system was used as a detector in HPLC. An expert estimation of the measurement results was applied to optimize the optical-scheme configuration of the spectrometer to achieve the longest linear calibration range and highest repeatability under chromatographic flow conditions. Chelates with 4-(2-pyridylazo)resorcinol were separated and determined with the limits of detection of n x 10(-8)- n x 10(-7) mol L(-1); the relative standard deviation of measurements was 46%. Xylenol Orange, 4-(2-thiazolylazo)resorcinol, and dithizone were studied as post-column reagents in thermal lens detection in ion chromatography. The limits of detection were n x 10(-8)- n x 10(-7) mol L(-1); the linear calibration ranges were about three orders; the relative standard deviation of measurements was 3-7%. A combined photothermal-refractometric detector for HPLC based on a polarization interferometer is proposed. Metal complexes as 4-(pyridylazo)resorcinol chelates (limits of detection of n x 10(-8)- n x 10(-7) mol L(-1)) and sugars (limits of detection of 10-20 ng L(-1)) were investigated as model substances. Obtained results were compared with results for traditional detectors, which show that photothermal detection has higher sensitivity than photometric and other absorption detectors.     

A new spectrofluorometric method for the determination of ascorbic acid based on its activating effect on a hemoglobin-catalyzed reaction.

A spectrofluorometric method for the determination of ascorbic acid (AA) based on its activation on the hemoglobin-catalyzed reaction was proposed. The fluorescence intensity of the product was measured under the optimal experimental conditions, i.e. 4.0 x 10(-6) M H2O2, 6.0 x 10(-5) M p-cresol, 1.2 M NH3-NH4Cl (pH 10.4) and 2.0 x 10(-7) M hemoglobin. The order of additions of the reagents was also studied. The activation of AA was found to be associated with a high ammonia concentration. The linear range of the method was 9.0 x 10(-10)-3.6 x 10(-8) M of AA. The detection limit was calculated to be 3.0 x 10(-10) M. The relative standard deviation of this method is 1.6% at 7.0 x 10(-9) M for 11 determinations.     

A simple light-emitted diode-induced fluorescence detector using optical fibers and a charged coupled device for direct and indirect capillary electrophoresis methods

We constructed a simple fluorescence detector for both direct and indirect CE methods using a blue light-emitted diode (470 nm) as excitation source, a bifurcated optical fiber as a waveguide, and a CCD camera as a detector. The connection of all the components is fairly easy even for nonexperts and the use of a CCD camera improves the applicability of this detector compared to the others using PMTs because it permits the recording of 2-D electropherograms or phosphorescence measurements. This detector provides a compact, low cost, and rapid system for the determination of native fluorescence compounds which have high quantum yields by CE with direct fluorescence detection, showing an LOD of 2.6 x 10(-6) M for fluorescein; the determination of fluorescence derivative compounds by CE with direct fluorescence detection, showing an LOD of 1.6 x 10(-7) M for FITC-labeled 1,6-diaminohexane; and nonfluorescence compounds by CE with indirect fluorescence detection with an LOD of 2.7 x 10(-6) M for gallic acid.     

Study of the Fluorescence Enhancement of Eu-Y-DEM-Dibenzoylmethane-Ammonia System

Abstract

The fluorescence enhancement and solvent effect of Eu-dibenzoylmethane-ammonia system was studied. The fluorescence intensity of the system can be greatly increased by y³⁺. The maximum fluorescence intensity was obtained at pH 8.9 – 9.5. The fluorescence intensity is a linear function of Eu²⁺ in the range of 1.0x10^?9 M -4.0x10^?8 M. The detection limit is 1.1x10^?10 M. The optimized procedure is applied to the determination of europium in lanthanide oxide samples.     

Determination of agmatine in biological samples by capillary electrophoresis with optical fiber light-emitting-diode-induced fluorescence detection

A capillary electrophoresis (CE)/optical fiber light-emitting diode (LED)-induced fluorescence detection method is developed for the determination of agmatine in biological samples. The agmatine was precolumn-derivatized with fluorescence tagging reagent, fluorescein isothiocyanate (FITC). Optimal separation and determination for agmatine were obtained with an electrophoretic buffer of 20 mM sodium borate (pH 9.2). Under the optimal conditions, the determination of agmatine was achieved in less than 4 min, and the detection limit was 4.1x10(-9) M (S/N = 3). The relative standard deviation (RSD) for 11 parallel determination of agmatine was less than 3.0%. The present CE-LED induced fluorescence detection method has been applied to detect agmatine in rat brain tissue, rat stomach tissue, human serum, and human urine. The level of agmatine in human urine was quantified by CE for the first time and found to be in the range 2.5-4.1x10(-7) M.     

A continuous flow system design for simultaneous determination of heavy metals in river water samples

A new design of a continuous flow system applied to the simultaneous determination of the concentration of zinc(II), cadmium(II), lead(II), copper(II), nickel(II), cobalt(II) and chromium(VI) in river water is described. A flow cell made in the laboratory, which has been patented, based on a 'wall-jet' configuration with a three-electrode system is described. Optimum conditions for the determination of the metal ions are reported. The detection limits and relative standard deviation values were 4.01x10(-9) M and 0.078 for Zn(II), 1.76x10(-10) M and 0.056 for Cd(II), 4.69x10(-10) M and 0.134 for Pb(II), 2.29x10(-10) M and 0.138 for Cu(II), 1.61x10(-9) M and 0.093 for Ni(II), 1.91x10(-9) M and 0.113 for Co(II), and 1.35x10(-9) M and 0.081 for Cr(VI). The procedure was applied to a sample of water from the Arlanzón river and the results were compared with inductively coupled mass plasma spectrometry (ICP-MS) as reference method. The final aim of this work is to design a flow system, which can be automated.     

An optode sensor for Cu2+ with high selectivity based on porphyrin derivative appended with bipyridine.

A porphyrin derivative (fluorophore) appended with bipyridine (ionophore) has been applied for preparation of a Cu2+-sensitive optical chemical sensor, which is based on fluorescence quenching of porphyrin derivative entrapped in a poly(vinyl chloride) membrane by the energy transfer process. The sensor exhibits a linear response toward Cu2+ in the concentration range 2.0 x 10(-8) - 1.0 x 10(-5) M, with a working pH range from 6.0 to 8.0 and a high selectivity. The detection limit is 5 x 10(-9) M. The response time for Cu2+ is less than 5 min with concentrations lower than 5 x 10(-6) M. The optode can be regenerated using 0.3 M EDTA (pH 9) and acetate buffer solution. The effect of the composition of the sensor membrane was studied, and the experimental conditions were optimized. The sensor has been used for direct determination of Cu2+ in water samples with satisfied results.     

Selective fluorescent Hg(II) detection in aqueous solutions with a dye intermediate

A dye intermediate, 1-amino-8-naphthol-3,6-disulfonic acid sodium (ANDS) was first used to selectively recognize Hg(II) in aqueous solutions with its fluorescence being strong quenched. The fluorescence quenching of ANDS was attributed to the formation of an inclusion complex between Hg(II) and ANDS by 2:1 complex ratio (K=6.2 x 10(9)), which has been utilized as the basis of the fabrication of the Hg(II)-sensitive fluorescent chemosensor. The analytical performance characteristics of the proposed chemosensor were investigated. The sensor shows a linear response toward Hg(II) in the concentration range 2.9 x 10(-6) to 5.5 x 10(-5)M with a limit of detection of 5.3 x 10(-7)M, and a working pH range from 5.0 to 9.0. It shows excellent selectivity for Hg(II) over a large number of cations such as alkali, alkaline earth and transitional metal ions. The proposed method was utilized successfully for the detection of Hg(2+) in water samples.