温度及pH敏感性共聚物水凝胶的合成及其对辅酶A的控制释放

以N-乙烯基吡咯烷酮(NVP)和甲基丙烯酸-N,N-二甲胺乙酯(DMAEMA)为单体,采用自由基聚合法合成了NVP与DMAEMA的共聚物及其水凝胶。研究发现共聚物的水溶液具有温度及pH双重敏感特性。相分离温度随DMAEMA含量的增加和水溶液浓度的降低而升高,随pH值的增大而减小且相变敏锐。通过对水凝胶溶胀率的考察,发现共聚凝胶在适当的单体浓度及交联剂浓度下,有较敏感的溶胀-退胀行为。在碱性条件下,共聚凝胶随温度的升高迅速退胀。pH=9时,改变温度,对辅酶A有很好的控制释放;而在酸性条件下,则无退胀行为,对辅酶A不能释放。     

N-异丙基丙烯酰胺-丙烯酰胺热敏凝胶的溶胀特性

制备并表征了N-异丙基丙烯酰胺-丙烯酰胺热敏凝胶(NIPAm-Am),研究了单体配比、引发剂、交联剂用量和温度对其溶胀特性的影响。结果表明：NIPAm-Am热敏凝胶是由亲水和疏水基团组成的非晶高聚物。mAm／mNIPAm越大,凝胶的平衡溶胀率越大;增加交联剂的用量,凝胶的溶胀率减小,当引发剂的质量分数为0．008时溶胀率达最大值;温度的增加会使凝胶的溶胀率减小,在相转变温度时,溶胀率的变化最大。     

丙烯酸β-羟丙酯/乙烯基吡咯烷酮水凝胶的合成和热敏行为的研究

用自由基共聚法合成了一系列 β -羟丙酯 ( β -HPAT)和乙烯基吡咯烷酮 (NVP)的共聚物及其水凝胶。发现共聚物的水溶液有敏锐的温敏行为 ,最低汇溶温度 (LCST)随NVP含量的增加而升高 ,随着反应单体总浓度的增加 ,相变敏锐性下降且LCST也随之下降。通过考察水凝胶的溶胀率 (SR) ,发现共聚凝胶在适当的单体浓度 ,交联剂浓度和较宽的单体浓度配比范围内 ,有较灵敏的温敏行为。     

侧链含不同功能性羟基的温敏性N-异丙基丙烯酰胺共聚物微凝胶的制备及性能比较

选择含有活性羟基的亲水单体多缩乙二醇单甲基丙烯酸酯(PEGMA)、甲基丙烯酸羟乙酯(HEMA),分别和N-异丙基丙烯酰胺(NIPAM)交联共聚,制备了侧链含有功能性羟基、链长不同的温敏性微凝胶.研究发现,亲水单体HEMA和PEGMA的引入对微凝胶的去溶胀性能有不同的影响,PEGMA的引入使得微凝胶的体积相转变温度升高,微凝胶的去溶胀比随着PEGMA投料比的增加而降低.而HEMA的引入使得微凝胶的体积相转变温度降低;微凝胶的去溶胀比随着HEMA投料比的增加先是增加然后降低,当HEMA的投料比为8mol%时,去溶胀比达到最大.     

P(AMPS-co-HEMA)凝胶的合成与吸银性能研究

以2-丙烯酰胺基-2-甲基丙磺酸(AMPS)和甲基丙烯酸羟乙酯(HEMA)为单体,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,过硫酸钾(KPS)为引发剂,采用自由基水溶液聚合法制备P(AMPS-co-HEMA)共聚凝胶,通过傅里叶红外光谱(FT-IR)对材料结构进行了表征.研究单体配比、交联剂的用量、引发剂的用量对共聚凝胶吸水性能的影响,并在此基础上对凝胶的溶胀、吸银及消溶胀性能进行研究.结果表明,当单体摩尔比n(AMPS)∶n(HEMA)=2∶1,交联剂用量ω(MBA)=0.6％,引发剂用量ω(KPS)=0.8％,所制得的凝胶吸水性能最好;凝胶在蒸馏水中的溶胀过程属于松弛平衡扩散;凝胶在AgNO3溶液中60min左右达到消溶胀平衡,且当AgNO3溶液的浓度为0.05mol/L时,银离子吸附量最大,为0.04g/g,消溶胀速率最快.     

手性温敏凝胶Poly(NIPAM-co-AAc-L-Trp)的制备及性能

利用L-色氨酸(L-Trp)为手性源,经酯化、缩合等反应制备手性单体AAc-L-Trp,进而在交联剂N,N’-亚甲基双丙烯酰胺(MBAA)和引发剂偶氮二异丁腈(AIBN)的作用下,与N-异丙基丙烯酰胺(NIPAM)发生自由基共聚制备了一种可用于手性拆分的新型手性温敏水凝胶Poly(NIPAM-co-AAc-L-Trp),其结构经IR确证.通过对其温敏性研究发现,相比于PNIPAM凝胶,疏水性手性单体的引入使Poly(NIPAM-co-AAc-L-Trp)凝胶的温敏性下降,LCST随着手性单体含量的增加而降低.以DL-苯丙氨酸为模型药物对其手性识别和拆分性能进行研究,结果表明,手性温敏凝胶可选择性地吸附D-型对映体,且吸附量随着手性单体含量增加而增加;提高温度(45°C)有利于手性温敏凝胶对DL-苯丙氨酸的拆分.     

聚丙烯酰胺-g-聚苯胺的导电水凝胶的制备及性能研究

通过两步聚合得到既具有良好力学强度又具有优良导电性能的聚丙烯酰胺-g-聚苯胺复合水凝胶.首先,丙烯酰胺和N-(4-氨苯基)丙烯酰胺在钴源γ-射线辐照下共聚形成聚丙烯酰胺水凝胶;然后,苯胺在具有微观多孔结构的聚丙烯酰胺凝胶中吸附,在过硫酸铵的作用下与凝胶的苯胺侧基发生接枝聚合,得到聚丙烯酰胺-g-聚苯胺水凝胶,并形成聚苯胺连续导电通道.改变辐照时间和辐照剂量率,所获得的聚丙烯酰胺水凝胶的凝胶分数随着辐照剂量的增加逐渐增大,而溶胀率随着辐照剂量的增加呈先增后减的趋势,表明凝胶的交联程度随辐照剂量呈规律性变化;辐照交联聚合的单体浓度对凝胶的性能,如溶胀率、微观结构和机械性能等也有影响.酸掺杂后,聚丙烯酰胺-g-聚苯胺复合凝胶的电导率达到9 S/m.     

疏水改性pH响应型智能水凝胶P(HEMA-NaAA-DiAC16)的制备及其溶胀性能

以二烯丙基胺和1-溴代十六烷为原料合成了疏水单体N,N-二烯丙基正十六烷胺(DiAC16),用FTIR、1H NMR 和元素分析对其进行了表征。 以2-羟基甲基丙烯酸乙酯(HEMA)、丙烯酸(AA)和N,N-二烯丙基正十六烷胺为共聚单体,N,N′-亚甲基双丙烯酰胺(BIS)为交联剂,十二烷基硫酸钠(SDS)为表面活性剂,过硫酸铵-四甲基乙二胺(TMEDA)为引发体系,制得的疏水改性智能水凝胶P(HEMA-NaAA-DiAC16)具有pH敏感特性。 研究了DiAC16、NaAA、BIS用量及pH值和离子强度等因素对水凝胶P(HEMA-NaAA-DiAC16)溶胀性能的影响。 结果表明,凝胶在水中的平衡溶胀率(为78.9～163.91),随DiAC16、BIS用量的增加和NaAA用量的减少而减少,n值(一般在0.5~1.0之间)随DiAC16、NaAA和BIS用量的增加而增加,为非Fickian扩散。 水凝胶的吸水溶胀是放热过程,ΔHm在-2.09～-3.64 kJ/mol,ΔHm的绝对值随DiAC16用量的减少、NaAA用量和BIS用量的增加而增大,聚合物与水的亲和力逐渐增强。 随离子强度的增强,平衡溶胀率下降。     

疏水改性pH敏感水凝胶P(HEMA-NaAA-DiAC_(16))的制备及其溶胀性能

以二烯丙基胺和1-溴代十六烷为原料合成了疏水单体N,N-二烯丙基正十六烷胺(DiAC16),用FTIR、1H NMR和元素分析对其进行了表征。以2-羟基甲基丙烯酸乙酯(HEMA)、丙烯酸(AA)和N,N-二烯丙基正十六烷胺为共聚单体,N,N'-亚甲基双丙烯酰胺(BIS)为交联剂,十二烷基硫酸钠(SDS)为表面活性剂,过硫酸铵-四甲基乙二胺(TMEDA)为引发体系,制得的疏水改性智能水凝胶P(HEMA-NaAA-DiAC16)具有pH敏感特性。研究了DiAC16、NaAA、BIS用量及pH值和离子强度等因素对水凝胶P(HEMA-NaAA-DiAC16)溶胀性能的影响。结果表明,凝胶在水中的平衡溶胀率(为78.9~163.91),随DiAC16、BIS用量的增加和NaAA用量的减少而减少,n值(一般在0.5~1.0之间)随DiAC16、NaAA和BIS用量的增加而增加,为非Fickian扩散。水凝胶的吸水溶胀是放热过程,ΔH m在-2.09~-3.64 kJ/mol,ΔH m的绝对值随DiAC16用量的减少、NaAA用量和BIS用量的增加而增大,聚合物与水的亲和力逐渐增强。随离子强度的增强,平衡溶胀率下降。     

基于改性多糖交联的生物可降解水凝胶的合成及其释药性

在4-二甲氨基吡啶(DMAP)的催化下,天然高分子海带多糖(Lam)与甲基丙烯酸缩水甘油酯(GMA)发生亲核取代反应,制备出一种新型水溶性生物可降解交联剂——甲基丙烯酸缩水甘油酯接枝海带多糖(Lam-GMA)。以Lam-GMA为交联剂,与丙烯酰胺(AM)单体共聚制备水凝胶。在生理条件与脂肪酶的作用下,对凝胶的溶胀特性和降解行为进行研究。以牛血清白蛋白(BSA)为模型高分子药物,包埋在水凝胶中,研究其降解释药行为。结果表明,GMA接枝到Lam链的反应转化率很高,并且接枝率可控;交联剂用量越大,水凝胶降解所需时间越长;随着水凝胶的降解BSA缓慢释放。     

利用手持技术改进测定乙醇分子结构实验

利用压强传感器代替排水集气法,改进测定乙醇分子结构实验的仪器装置,并探索最佳反应条件。另外,设计两个空白实验,结合压强变化曲线对实验误差进行相关讨论。     

光谱仪测试范围的扩展

由于石化行业的生产需要，其材质的使用具有多样性和广泛性，经常会出现顾客委托的测试样品的一个或几个元素跨越光谱仪现有测试程序测量范围的情况。本法通过对光谱仪测试原理的认识，根据光谱仪的测试能力及标样的采集，实现了一个或几个元素测量范围的扩展，并对其测量的影响因素进行了研究。     

Influence of viscosity of medium on processes of oxygen quenching of excited states of mesoporphyrin

The oxygen quenching rate constants for singlet and triplet excited states of the dimethyl ester of mesoporphyrin IX increase with decreasing viscosity of the medium and reach a maximum at a viscosity of approximately 0.4 mPa·sec, after which the rate constants begin to decrease. The drop in rate constant with increasing fluidity of the medium may be related to a nonequilibrium character of the elementary act in the interaction of the reactants in the solvent cage. In viscous media such as isopropyl alcohol, isobutyl alcohol, and isoamyl alcohol, the reaction radius is greater than the sum of the radii of the reacting particles. The long-range character of these processes is due to the relatively weak dependence of the quenching probability on distance.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 2, pp. 161–167, March–April, 1989.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

物质分配系数的测定实验改进

实验教学目的是从解决实际问题出发,以实验技术训练和实验设计思想培养为目标。介绍了将单一的物质分配系数测定实验改进为综合实验,提高了实验效果及实验资源利用率。     

Neutral diterpenoids of oleoresins of five species of conifers of Transcarpathia

The compositions of the neutral diterpenoids of the oleoresins of five species of conifers growing in the Transcarpathia have been studied. It has been found that the oleoresins ofAbies alba M.,Larix decidua M., andPicea excelsa L. contain more than 50% of neutral diterpenoids. The group and qualitative compositions of the oxygen-containing diterpenoids have been determined. In the oleoresins ofAbies alba,Picea excelsa, andPicea abies tertiary alcohols — cis-abienol and isocembrol — predominate, while inLarix decidua the main component is the hydroxy ester larixyl acetate. Primary alcohols related to the resin acids have been found in all the oleoresins investigated. Features of the distribution of diterpenoids according to the species of conifers have been revealed. The results obtained are necessary for the chemotaxonomy of conifers of the family Pinceae.Novosibirsk Institute of Organic Chemistry, Siberian Branch, Academy of Sciences of the USSR. Translated from Khimiya Prirodynkh Soedinenii, No. 6, pp. 812–816, November–December, 1988.     

Calculation of enthalpies of hydrogenation of hydrocarbons

Sets of hydrogen molecule equivalents have been developed which permit the calculation of hydrogenation of different types of carbon-carbon bonds from ab initio total energies (3-21G and 6-31G* basis sets, and, to a more limited extent, for MP2/6-31G* data) of reactants and products. The calculated enthalpies of hydrogenation are in good agreement with experiment for unstrained molecules, with average errors on the order of 2 kcal/mol. The 6-31G* equivalents allow the enthalpies for strained molecules to be calculated accurately, but the 3-21G equivalents do not. The equivalents for both basis sets have been tested by calculating the enthalpies of hydrogenation of carbon-carbon bonds in nitrogen- and oxygen-containing organic molecules, free radicals, and classical carbocations. The results are in good agreement with experiment in most cases.