Formation of superlattices via blending of block copolymers

Block copolymers are well‐known for their large number of microphase morphologies on mesoscopic length scales. After a short review of the different morphologies observed in binary block copolymers and ternary triblock copolymers, the self‐assembling in blends of different block copolymers into common superlattices is discussed in detail. Besides similar morphologies known for pure triblock and diblock copolymers, the blends can also show new morphologies. Examples of such new morphologies are periodic non‐centrosymmetric lamellae and multiple gyroid interface structures. The discussion of the superlattices is primarily based on investigations by transmission electron microscopy (TEM), which are supplemented in a few cases by small angle X‐ray scattering (SAXS) or results from computer simulations.     

Pattern formation and ordering in thin films of crystallisable block copolymers

We show that tapping-mode atomic force microscopy provides real-space and time-resolved observations of morphology and pattern formation resulting from crystallisation of annealed thin films of polyethelenoxide or microphase-separated low-molecular-weight hydrogenated poly(butadiene-b-ethyleneoxide) diblock copolymers. Differences in viscoelastic properties allow distinguishing crystalline and molten (amorphous) areas with a nanometer resolution.     

In-plane and out-of-plane defectivity in thin films of lamellar block copolymers

We investigate the ordering of poly(styrene-b-methyl methacrylate) (PS-PMMA) lamellar copolymers (periodicity L₀ = 46 nm) confined between a free surface and brushed poly(styrene-r-methyl methacrylate) silicon substrate. The processing temperature was selected to eliminate wetting layers at the top and bottom interfaces, producing approximately neutral boundaries that stabilize perpendicular domain orientations. The PS-PMMA film thickness (t = 0.5L₀ − 2.5L₀) and brush grafting density (Σ = 0.2–0.6 nm⁻²) were systematically varied to examine their impacts on in-plane and out-of-plane ordering. Samples were characterized with a combination of high-resolution microscopy, X-ray reflectivity, and grazing-incidence small-angle X-ray scattering. In-plane order at the top of the film (quantified through calculation of orientational correlation lengths) improved with tⁿ, where the exponent n increased from 0.75 to 1 as Σ decreased from 0.6 to 0.2 nm⁻². Out-of-plane defects such as tilted domains were detected in all films, and the distribution of domain tilt angles was nearly independent of t and Σ. These studies demonstrate that defectivity in perpendicular lamellar phases is three-dimensional, comprised of in-plane topological defects and out-of-plane domain tilt, with little or no correlation between these two types of disorder. Strong interactions between the block copolymer and underlying substrate may trap both kinds of thermally generated defects. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 339–352     

Control of the microdomain orientation in block copolymer thin films with homopolymers for lithographic application

Block copolymer lithography is a promising method for fabricating periodical nanopatterns of less than 20 nm by self-assembly and can be applicable for fabricating patterned magnetic media with a recording density over 1 Tb/in.2. We found a simple technique to control the orientation of cylindrical microdomains in thin films. Simply by mixing polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) diblock copolymers with the homopolymer (PS or PMMA) of the major component, we could align the cylindrical microdomains perpendicular to the film surface. The added homopolymer induces conformational entropic relaxation of the block chains in microdomain space and stabilizes the perpendicular orientation of hexagonally packed cylindrical microdomains. Thus formed perpendicular cylinders can be readily aligned in a regular array with a grating substrate.     

Nanoparticle directed domain orientation in thin films of asymmetric block copolymers

We investigated the thin film morphology of two different asymmetric block copolymers (BCP), polystyrene-block-poly(4-vinylpyridine) (PS-b-P4VP) and poly(n-pentyl methacrylate)-block-poly(methyl methacrylate) (PPMA-b-PMMA), loaded with pre-synthesized iron oxide nanoparticles (NP). The chemical composition of the BCP constituents determines the strength of the interaction between polymer chains and nanoparticles. In the case of NP/PS-b-P4VP system, the nanoparticles interact preferentially with the P4VP block and hence localize selectively in the P4VP cylindrical microdomains. However, for the NP/PPMA-b-PMMA system, the nanoparticles have no significant preference for the copolymer blocks and segregate at the polymer/substrate interface. Interestingly, this changes the effective substrate surface energy and hence leads to a remarkable change in domain orientation from parallel to perpendicular with respect to the substrate. These results clearly demonstrate the importance of both enthalpic and entropic factors which determine spatial distribution of NP in BCP films and influence domain orientation.     

Dendritic homopolymers and block copolymers: Tuning the morphology and properties

The synthesis and characterization of dendritic homopolymers and block copolymers of ?‐caprolactone and lactide (L ‐lactide and racemic lactide) were performed with multifunctional initiators in combination with living polymerization and the selective placement of branching junctures in a divergent growth strategy. A hexahydroxy‐functional 2,2‐bis(hydroxymethyl) propionic acid derivative was used as an initiator for the stannous‐2‐ethylhexanoate‐catalyzed living ring‐opening polymerization of ?‐caprolactone, L ‐lactide, and racemic L ,D ‐lactide. Branching junctions at the chain ends were introduced with benzylidene‐protected 2,2‐bis(hydroxymethyl) propionic acid. Subsequent generations were then polymerized, after deprotection, from these star‐shaped macroinitiators. Successive chain end capping and initiation produced three generations of polymers with molecular weights in excess of 130,000 g/mol and narrow polydispersities (<1.20). It was possible to prepare diblock and triblock copolymers with phase‐separated morphologies, and with L ‐lactide or D ,L ‐lactide, semicrystalline and amorphous morphologies were demonstrated. The polymers were characterized by ¹H NMR, ¹³C NMR, size exclusion chromatography, and differential scanning calorimetry. The compositions of the block copolymers and the conformational structures of the optically active polymers were also confirmed by optical rotation measurements. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1174–1188, 2004     

Monte-Carlo simulation of ternary blends of block copolymers and homopolymers

We perform a theoretically informed coarse grain Monte-Carlo simulation in the nPT-ensemble and the Gibbs ensemble on symmetric ternary mixtures of AB-diblock copolymers with the corresponding homopolymers. We study the lamellar period by varying the length and amount of homopolymers. The homopolymer distribution within the lamellar morphology is determined as is the maximum amount of homopolymer within the lamellae. Gibbs ensemble simulations are used to locate the three-phase coexistence between two homopolymer-rich phases and a lamellar phase.     

Synthesis, post-modification and self-assembled thin films of pentafluorostyrene containing block copolymers

Block copolymers consisting of a pentafluorostyrene (PFS) block and a hydrophilic block were synthesized by RAFT polymerisation. The hydrophilic blocks consist of methacrylate derivatives, 4-hydroxystyrene or 4-vinylpyridine monomers. The block copolymers were obtained with narrow molecular weight distributions and the molecular weights were in good agreement with the theoretical values. In addition, a model thiol was reacted with the PFS moieties of the block copolymers. This polymer–analogous reaction was performed under ambient conditions in high yields resulting quantitatively in para-substitution of the pentafluorophenyl rings. Finally, thin films consisting of block copolymers that showed strong phase-segregation behaviour and ordered nanostructured surfaces consisting of both blocks were obtained.     

Phase separation in thin films of end‐grafted block copolymers

An atomic force microscopy investigation was carried out on various thick (30–120 nm) polymethyl methacrylate‐b‐polystyrene and poly(2‐(dimethyl amino)ethyl methacrylate)‐b‐polystyrene films prepared via a grafting‐from method. The structure of the films was examined with both topographic and phase imaging. Several different morphologies were observed including a perforated lamellar phase with irregular perforations. In addition, complementary small‐angle X‐ray scattering and reflectometry results measurements on a non‐grafted polymer are presented. Copyright © 2009 John Wiley & Sons, Ltd.     

Phase behavior in thin films of cylinder-forming ABA block copolymers: experiments

We experimentally establish a phase diagram of thin films of concentrated solutions of a cylinder forming polystyrene-block-polybutadiene-block-polystyrene triblock copolymer in chloroform. During annealing the film forms islands and holes with energetically favored values of film thickness. The thin film structure depends on the local thickness of the film and the polymer concentration. Typically, at a thickness close to a favored film thickness parallel orientation of cylinders is observed, while perpendicular orientation is formed at an intermediate film thickness. At high polymer concentration the cylindrical microdomains reconstruct to a perforated lamella structure. Deviations from the bulk structure, such as the perforated lamella and a wetting layer are stabilized in films thinner than approximately 1.5 domain spacings.     

Phase behavior in thin films of cylinder-forming ABA block copolymers: mesoscale modeling

The phase behavior of cylinder-forming ABA block copolymers in thin films is modeled in detail using dynamic density functional theory and compared with recent experiments on polystyrene-block-polybutadiene-block-polystyrene triblock copolymers. Deviations from the bulk structure, such as wetting layer, perforated lamella, and lamella, are identified as surface reconstructions. Their stability regions are determined by an interplay between surface fields and confinement effects. Our results give evidence for a general mechanism governing the phase behavior in thin films of modulated phases.     

Grazing-incidence transmission small angle X-ray scattering from thin films of block copolymers

Thin films of lamellar and cylindrical block copolymers are popular systems for low-cost nanolithography. To be useful as nanoscale templates, the lamellae or cylinders must be oriented perpendicular to the substrate. Domain orientations are usually characterized by microscopy measurements of the film surface, but these techniques cannot detect tilted, bent, or tortuous domains in the film interior. We report a simple method to quantify out-of-plane disorder in thin films of block copolymers based on a variant of grazing-incidence small angle X-ray scattering (GI-SAXS). A typical GI-SAXS experiment illuminates the center of a substrate-supported film at a grazing angle of incidence (near the film/substrate critical angle), and the strong reflected signal is interpreted with the distorted-wave Born approximation. In a new approach, the beam footprint is moved to the far edge of the sample, allowing the acquisition of a transmission pattern. The grazing-incidence transmission data are interpreted with the simple Born approximation, and out-of-plane defects are quantified through analysis of crystal truncation rods and partial Debye-Scherrer rings. Significantly, this study demonstrates that grazing-incidence transmission small angle X-ray scattering can detect and quantify the buried defect structure in thin films of block copolymers. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Highly ordered nanoporous thin films by blending of PSt‐b‐PMMA block copolymers and PEO additives as structure directing agents

Herein, we present a simple method for producing nanoporous templates with a high degree of lateral ordering by self‐assembly of block copolymers. A key feature of this approach is control of the orientation of polymeric microdomains through the use of hydrophilic additives as structure directing agents. Incorporation of hydrophilic poly(ethylene oxide) (PEO) moieties into poly(styrene‐b‐methyl methacrylate) (PSt‐b‐PMMA) diblock copolymers gives vertical alignment of PMMA cylinders on the substrate after solvent annealing. Because of the miscibility between PEO and PMMA, PEO additives were selectively positioned within PMMA microdomains and by controlling the processing conditions, it was found that ordering of PSt‐b‐PMMA diblock copolymers could be achieved. The perpendicular orientation of PMMA cylinders was achieved by increasing the molecular size of the PEO additives leading to an increased hydrophilicity of the PMMA domains and consequently to control the orientation of microdomains in PSt‐b‐PMMA block copolymer thin films. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8041–8048, 2008     

Robust control of microdomain orientation in thin films of block copolymers by zone casting

Block copolymers with chemically immiscible segments exhibit a variety of microphase-separated nanostructures on the scale of 10-100 nm. Controlling the orientation of these microphase separated nanostructures is vital in many applications such as lithography, membranes, data storage, and so forth. Typical strategies involve the use of external fields or patterned substrates. Here, we report a robust zone casting technique to achieve highly ordered thin films of block copolymers on centimeter-scale substrates. The robustness of this technique is its powerful control on diverse morphologies and exceptional tolerance on versatility of block copolymer chemistry as well as allowance of a wide spectrum of substrates. We demonstrate that perpendicular orientations with respect to the surface are achieved for block copolymers with both lamellar and cylindrical morphologies by controlling solution casting rate, temperatures, and block copolymer chemical structures. Thin films of both noncrystalline and crystalline block copolymers exhibit excellent orientational order and lateral order. However, the lateral order in the thin films of crystalline block copolymers shows dependence on casting temperature and melting temperature of the crystalline segment. Remarkably, all the ordering is independent of the substrates on which the block copolymer films are cast.     

Crazing in thin films of styrene–butadiene–styrene block copolymers

The mechanism of craze initiation and growth and its relationship to mechanical properties has been studied in thin films of styrene–butadiene–styrene (SBS) block copolymers. Optical microscopy and transmission electron microscopy were used to examine three copolymers which has a spherical rubber domain morphology but varied in rubber content from 20 to 50%. With increasing rubber content, the crazes became longer and less numerous. Widening of the crazes was at least partially responsible for the higher strains achieved in the copolymers, especially for the composition with the highest rubber content where the crazes widened to form micronecks. Transmission electron microscopy revealed that craze initiation and growth at the craze tip occurred by cavitation in the polystyrene phase. Cavitation of the continuous phase rather than the rubber domains was attributed to the concentration of chain-end flaws in the polystyrene. Crazes in the block copolymers followed a meandering pathway and the boundaries between crazed and uncrazed material were indistinct. Incorporation of fibrillated rubber particles into the craze fibrils strengthened the craze. At higher rubber content, the craze widened in the stress direction by voiding and fibrillation, which produced a cellular morphology.     

Synthesis and characterization of biodegradable homopolymers and block copolymers based on adipic anhydride

Homopolymers of adipic anhydride (AA) and block copolymers of ϵ-caprolactone (ϵ-CL) and AA have been synthesized with aluminum triisopropoxide as an initiator. Homopolymerization was studied at 20°C in toluene and methylene chloride (CH₂Cl₂). The end-group analysis agrees with a coordination insertion mechanism based on the acyl-oxygen cleavage of the AA ring. Living poly(ϵ-caprolactone) (PCL) chains are very efficient macro-initiators for the polymerization of AA, with formation of diblock copolymers of a narrow molecular weight distribution. At our best knowledge, low molecular weight ω-aluminum alkoxide PCL macroinitiators (M_n < 1000) allow the first valuable synthesis of PAA with a molecular weight as high as 58,000 and a quite narrow polydispersity (M_w/M_n = 1.2). Size-exclusion chromatography (SEC) and ¹³C NMR confirm the blocky structure of the copolymers, in agreement with DSC that shows two melting endotherms and two glass transitions characteristic of the crystalline and amorphous phases of PCL and PAA, respectively. Block copolymers of ϵ-CL and AA are also sensitive to hydrolysis, which makes them possible candidates for biomedical applications. Initiation of the AA polymerization in bulk with aluminum triisopropoxide in the presence of various ligands is also discussed. © 1997 John Wiley & Sons, Inc.     

Self‐assembly of metallo‐supramolecular block copolymers in thin films

The self‐assembly of a metallo‐supramolecular PS‐[Ru]‐PEO block copolymer, where ‐[Ru]‐ is a bis‐2,2′:6′,2″‐terpyridine‐ruthenium(II) complex, in thin films was investigated. Metallo‐supramolecular copolymers exhibit a different behavior as compared to their covalent counterparts. The presence of the charged complex at the junction of the two blocks has a strong impact on the self‐assembly, effecting the orientation of the cylinders and ordering process. Poly(ethylene oxide) cylinders oriented normal to the film surface are obtained directly regardless of the experimental conditions over a wide range of thicknesses. Exposure to polar solvent vapors can be used to improve the lateral ordering of the cylindrical microdomains. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4719–4724, 2008     

Defect evolution in block copolymer thin films via temporal phase transitions

We study the details of the defect dynamics in thin films of a cylinder-forming polystyrene-block-polybutadiene (SB) diblock copolymer melt. The high temporal resolution of in-situ scanning force microscopy (SFM) uncovers elementary dynamic processes of structural rearrangements on time scales not accessible so far. Short-term interfacial undulations and the formation of transient phases (spheres, perforated lamellae, and lamellae) are observed. We demonstrate that the well-known structural defects are annihilated by short-term phase transitions into what may be considered excited states. These temporary phase transitions are reproduced in simulations based on dynamic self-consistent field theory. We discuss the role of the observed structural evolution in the context of the equilibrium phase behavior in SB thin films.     

Effect of substrate and molecular weight on the stability of thin films of semicrystalline block copolymers

The thermal stability of the thin film morphology of two symmetric oxyethylene/oxybutylene block copolymers (E76B38 and E114B56) on mica and silicon was investigated via atomic force microscopy (AFM). It is found that morphological transition of EmBn thin films during melting is strongly dependent on the molecular weight of the diblock copolymers and their interaction with the substrate. For E76B38 on mica, a single-layered structure transforms into a double-layered structure upon melting, but the same polymer on silicon retains a single-layered structure after melting and spreads quickly to wet-out the silicon surface. Conversely a longer polymer, E114B56, has a thin film on mica that does not change much after melting of the crystalline E block. A mechanism was proposed to explain the relative stability of E76B38 and E114B56 thin films upon melting. Internal stress is produced during melting and can be released along two directions. The release along the vertical direction is restricted by the energy barrier related to the segregation strength, and the release along the horizontal direction is dependent on the mobility of block copolymer related to the interaction between the block copolymer and the substrate. Domain size affects the release rate of the internal stress along the horizontal direction and thus the thermal stability of EmBn thin films. Switching between horizontal and vertical releases can be realized by controlling the domain size of the thin films.