Formation of TiO2 Sols,Gels and Nanopowders from Hydrolysis of Ti(OiPr)4 in AOT Reverse Micelles

Titania sols, gels and nanopowders have been produced by the controlled hydrolysis of tetraisopropyltitanate (TPT) in sodium bis(2-ethylhexyl)sulfosuccinate (AOT) reverse micelles. Particle formation and aggregation have been investigated by photon correlation spectroscopy, the crystal phases by FT-Raman spectroscopy, and the crystallite dimensions of the precipitates by transmission electron microscopy. Nanoparticles could be produced at relatively high Ti(IV) concentrations (up to 0.05 mol dm^–3). These nanoparticles aggregated into sols, with colloid sizes of 20–300 nm, eventually forming gelatinous precipitates. The kinetics of particle formation and aggregation were controlled by varying the primary process parameters [TPT], [H₂O]/[AOT] (w₀), and [H₂O]/[Ti(IV)] (R), yielding a range of products including stable, transparent sols, precipitates and monolithic gels. The aggregation kinetics and physical properties of the sols depended strongly on w₀. Different titania phases were produced, depending on w₀; w₀ 6 yielded amorphous particles, while w₀ 10 produced anatase. The dimensions of the crystallites were comparable to those of the parent reverse micelles. A model was developed to interpret the effect of the primary process parameters on colloidal stability: (1) nucleation to form primary crystallites occurs by rapid hydrolysis and condensation reactions within the reverse micelle and (2) subsequent colloidal growth by aggregation occurs by reverse micellar exchange, where the rate of growth is governed by electrostatic and steric stability factors which increase as [AOT]/[TPT] (S) and residual [H₂O]/[AOT] (w_r) increase.     

Specific interactions in reversed micelles: Oxidation of Fe(bpy)32+ by S2O82− in AOT-oil-water microemulsions

The oxidation of Fe(bpy)₂²⁺ by peroxodisulphate (bpy = 2,2′-bipyridine) has been studied in a variety of sodium bis(2-ethylhexyl)sulfosuccinate(aerosol-OT or AOT)-oil-water microemulsions by changing the nature of the oil phase, the surfactant concentration, and the molar ratio w = [H₂O]/[AOT]. Kinetic results show that the influence of surfactant concentration is due to a dilution effect. On the other hand, the comparison between the reaction rate in conventional aqueous solution with that in AOT w/o microemulsions seems to indicate that the iron(II) species is distributed between the aqueous phase and the interphase. © 1995 John Wiley & Sons, Inc.     

Rheological Measurements in Titania Gels Synthesized from Reverse Micelles

Abstract

TiO₂ sol and gel systems have been synthesized by hydrolysis of titanium butoxide in microemulsions W/O. Different systems compositions were prepared at constant W _o = [H₂O]/[AOT] and changing R = [H₂O]/[Ti(BuO)₄]. Experimental measurements show a progressive increase of the viscosity with time, characteristic of a sol-gel transition. The rheology of the transition was studied by following the behavior of viscoelastic parameters (G′, G″ and η?) as a function of time at different frequencies.

The possibility to apply standard percolation theory was discussed. The application of two alternative growth models-either “fractal growth model” or “nearly linear growth model”-has been analysed.     

Conformational studies of the oligomers of L-lysine in reversed micelles

The effect of the chain length on the conformation of oligo-L-lysines (Lys-n, n= 9, 12 and 15) was examined in the reversed micelles of bis(2-ethylhexyl)sodium sulfosuccinate (AOT) in octane by the circular dichroism (CD) measurements. These oligomers seem to take a-structure in these systems. The structure-inducing effect of the reversed micelles is enhanced as the molar ratio of water to AOT (w₀=[H₂O]/[AOT]) becomes smaller. On the other hand, in the aqueous solutions the oligomers having 12 and 15 residues show the conformational transition from random coil to-helical structure by the addition of AOT, but the short oligomer of 9 residues does not show such a conformational transition.     

Conformational studies of basic poly (α-amino acid)s in reversed micelles

The conformation of various basic poly (-amino acid)s was investigated by CD measurements in aqueous solutions containing bis (2-ethylhexyl)sodium sulfosuccinate (AOT) as well as in the AOT reversed micelles. The addition of AOT into an aqueous solution of poly(L-lysine) induces the conformational transition from coil to ordered structure, followed by aggregation. On the other hand, poly(L-lysine) assumes-structure in the reversed micelles at low w_ovalue (w_o=[H₂O]/[AOT]). Similarly to poly(L-lysine), poly(L-ornithine) takes an ordered structure in the aqueous solution containing AOT and-structure in the reversed micelles. In this case, however, these ordered structures are not so stable, compared with that of poly(L-lysine). Poly(L-arginine) undergoes the conformational transition from coil to helix by addition of AOT into the aqueous solution. Further addition of AOT allows transformation into-structure. Copoly(L-lysyl-L-leucine) with 63% leucine residue was shown to take a stable helical conformation even in pure water. In the reversed micelles, however, this ordered structure is significantly changed probably because the hydrophobic interaction among the leucyl residues is lowered in the reversed micelles.     

Conformational studies of poly(N5-Ω-hydroxyalkyl-L-glutamine)s in reversed micelles

The molecular conformations of poly(N⁵-dihydroxyethylaminopropyl-L-glutamine) and poly(N⁵-dihydroxyethyl-L-glutamine) were investigated in reversed micelles of AOT as well as in aqueous solutions. Both poly(-amino acid)s assume disordered structures in pure water. The conformation of poly(N⁵-dihydroxyethylaminopropyl-L-glutamine) transits into-helix in the reversed micelles as the molar ratio of water to AOT (w₀=[H₂O]/[AOT]) becomes smaller. A similar conformational transition was also observed in aqueous solutions when a certain amount of AOT was added. Under these conditions, however, poly(N⁵-dihydroxyethyl-L-glutamine) did not undergo a conformational transition into-helix.     

Structural and catalytic aspects of cutinase in w/o microemulsions

 Structural and catalytic properties of cutinase were studied in bis(2-ethylhexyl) sodium sulfo-succinate (AOT)-isooctane microemulsion systems. The effect of the water content of the microemulsions on the cutinase activity on an esterification reaction of lauric acid with pentanol showed that cutinase followed a bell-shaped profile presenting a maximum at w _o=9, with w _o=[H₂O]/[AOT]. Kinetic studies allowed the determi-nation of the apparent parameters K _m and V _max. Electron paramagnetic resonance (EPR) spectroscopy studies of active site labeled cutinase in microemulsions with varying w _o values showed that in all microemulsions, the mobility of the label is higher than in the aqueous solution. Furthermore, it was found that the maximum of the enzyme activity did not correspond to a reduced active site mobility. Up to w _o=9 there was an increase of both activity and active site mobility. As the water content of the system became higher, the mobility of the bound spin label further increased whereas the enzymatic activity dropped considerably. Received: 20 December 1996 Accepted: 24 February 1997     

Volumetric and transport properties of aerosol-OT reversed micelles containing light and heavy water

Densities and viscosities of sodium bis(2-ethylhexyl) sulfosuccinate (AOT in-heptane system containing light and heavy water, as a function of the molar ratio R (R=[H₂O or D₂O]/[AOT]) were measured at 0, 5, 25 and 40°C. At low R values, the apparent molar volume of deuterium oxide is smaller than that of light water. The difference is related to the strength of the hydrogen bonding H₂O and D₂O. The viscosities of both H₂O-AOT-n-heptane and D₂O-AOT-n-heptane systems were explained in terms of intermicellar interactions mainly governed by hydration of the head groups of AOT.     

The ligand effect in Ti‐mediated living radical styrene polymerizations initiated by epoxide radical ring opening. 1. Alkoxide and bisketonate Ti complexes

Bisketonate and alkoxide Ti(III) complexes derived from Zn reduction of Ti(IV) precursors were evaluated as catalysts for the living radical polymerization (LRP) of styrene initiated by Ti‐catalyzed epoxide radical ring opening and mediated by reversible termination with Ti(III). No polymerization occurred with tris(2,2,6, 6‐tetramethyl‐3,5‐heptanedionato)titanium (III), whereas dichlorobis(2,2,6,6‐tetramethyl‐3,5‐heptanedionato)titanium (IV) affords only a free radical polymerization. Preliminary living features were displayed by (ⁱPrO)₂TiCl₂. Investigations of the effect of epoxide/Ti/Zn ratios, temperature, and nature of the epoxide demonstrated that (ⁱPrO)₃TiCl provides a linear dependence of M_n on conversion over a wide range of conditions with an optimum for [Sty]/[epoxide group]/[Ti]/[Zn] = 50/1/2/4 at 90 °C. However, the polydispersity could not be reduced below 1.4–1.5, with an initiator efficiency of 0.15. These results were rationalized in terms of a combination of decreased Ti oxophilicity and ligand exchange. The lowered oxophilicity decreases the initiation rate and broadens M_w/M_n. The fast alkoxide exchange promotes a weak dependence of the polymerization on reaction conditions and generates macromolecular Ti species with reduced ability to mediate LRP. Thus, while monofunctional epoxides provide homogeneous polymerizations and narrower M_w/M_n, difunctional initiators may lead to gel formation at high conversion. Nonetheless, all polymerizations were light gray to colorless and afforded white polymer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6028–6038, 2005     

Comparison of activities of homogeneous Ti-based catalysts in the presence of methylaluminoxane (MAO) for synthesis of syndiotactic polystyrene by UV/visible spectroscopic study

The catalytic activities in syndiospecific polymerization of styrene in hydrocarbon using homogeneous Ti-based catalysts in the presence of methylaluminoxane (MAO) were investigated through UV/visible spectroscopic analysis. A strong UV absorption band of CpTiCl₃, itself, incipiently appeared at λ_max = 400 nm in toluene, followed by a bathochromic shift with its remarkable decrease by the addition of MAO. The absorption band intensity at λ_max = 400 nm arising from delocalization of π-electrons on the cyclopentadienyl ring decreased by methylation in the presence of MAO with regard to the mechanism for production of an active center (“cation-like”), for example, the change of the ionic nature. The intensity decrease at λ_max = 400 nm was suppressed over 2000 of the [Al]/[Ti] ratio. In the case of Ti(OC₄H₉)₄ having a σ-ligand, new and broad UV absorption bands were developed at λ_max = 340 nm and 410 nm in the presence of MAO in contrast with the CpTiCl₃/MAO system. Comparison between the relative absorption intensities at λ_max = 340 nm and 410 nm led to the determination of a maximum catalytic activity of Ti(OC₄H₉)₄ in the presence of MAO related to the polymerization yield. The maximum polymerization yield was observed with regard to the relative maximum value of the absorption intensity at λ_max = 410 nm with the [Al]/[Ti] ratio (500). From observation for polymorphism of the final products via differential scanning calorimetric analysis (DSC), the thermally unstable β-form seemed to be produced by the CpTiCl₃/MAO system independent of the MAO concentration, the Ti(OC₄H₉)₄/MAO system produced a thermally stable α-form in the low MAO concentration (up to 100 of the [Al]/[Ti] ratio), and a mixture of α- and/or β-forms over 200 of the [Al]/[Ti] ratio under our experimental conditions. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1733–1741, 1998     

Complexation of Al(III) by 8-Hydroxyquinoline and Drastic Fluorescence Enhancement in Reverse Micelles

Complexation of Al^IIIby 8-hydroxyquinoline and fluorescence behavior of the quinolinate(s) were studied in reverse micellar systems at low water content, and compared to aqueous media. Two surfactants were used: one was cationic (CTAC: cetyltrimethylammonium chloride) and the other was anionic (AOT: sodium bis(2-ethylhexyl)sulfosuccinate). The results obtained in the CTAC/dichloromethane system (W= [H₂O]/[surfactant] = 0.9) showed that complexation occurred very likely in the oil phase and no micellar effect was observed. On the contrary, in the presence of AOT, specific micellar effects were observed due to the presence of the anionic polar heads: stabilization of the positively charged 1:1 and 1:2 chelates, at the expense of the neutral water-insoluble 1:3 chelate which is formed in aqueous solutions under similar conditions;drastic fluorescence enhancement factorsof 120 and 100 in AOT/heptane (W= 1.5) and AOT/dichloromethane (W= 1.6), respectively. Such factors have never been reported so far in either hydroorganic or direct micellar systems. In return, the length of time for the production of the complex(es) is increased because of the microheterogeneity of the medium and the small sizes of the water pools.     

Spectrophotometric determination of traces of hydrogen peroxide with the Ti(IV)-xylenol orange and the Ti(IV)-chromazurol S reagents

The formation of mixed ligand complexes in Ti(IV)-xylenol orange (XO)-H₂O₂ and Ti(IV)-chromazurol S (CAS)-H₂O₂ systems was studied by spectrophotometry. The former system gave constant absorbance (λ_max = 562 nm) under the condition of [XO]/[Ti(IV)] = 1 in the pH 2–4 region. In the latter system, a distinct maximum at 557 nm was observed when [CAS]/[Ti(IV)] = 4 in the pH range of 4.5–5.2. In both cases, the absorbance at λ_max was stable for a long time and proportional to the concentration of hydrogen peroxide. From those facts, the usefulness of the mixtures of Ti(IV)-XO and Ti(IV)-CAS as the colorimetric reagents for the determination of hydrogen peroxide can be expected. The conditions for the use of the Ti(IV)-XO and the Ti(IV)-CAS reagents were examined in detail, and both reagents were found to be available for trace analysis of hydrogen peroxide with high sensitivity.     

Triglyceride hydrolysis and stability of a recombinant cutinase fromFusarium solani in AOT-iso-octane reversed micelles

A recombinant cutinase fromFusarium solani was encapsulated in AOT reversed micelles. Physicochemical parameters of the system were optimized relative to triolein hydrolysis. Kinetic studies of triglyceride hydrolysis showed a decrease in specificity with increase of the acyl chain length. Stability of cutinase in the system under study is lower than in aqueous solution and decreases with increase in the water content in the system (W₀ = [H₂O]/[AOT]). The products of triolein hydrolysis had little effect on the cutinase stability. Although glycerol did not alter the stability, oleic acid decreases the enzyme stability. The increase in log P of solvent (fromiso-octane ton-dodecane) decreased the stability. Deactivation profiles were fitted with the Henley and Sadana model (1).     

Hyperbranch-polyethyleniminated functional polymers II: effect of polyethyleniminated polyoxypropylenediamines on copper nanoparticle formation in aqueous solution

Colloidal aqueous solution of zerovalent copper (Cu(0)) nanoparticles were prepared from the Cu²⁺ ions coordinated with polyethyleniminated polyoxypropylenediamines (D400(EI) _x ) followed by chemical reduction of NaBH₄. Aqueous solution of copper clusters formed in the presence of D400(EI)₈ with a loading ratio of [EI]/[Cu²⁺] = 3 were stable without precipitation for standing more than 1 month. The protective effects of D400(EI) _x and the particle size of the resulted Cu nanoparticle are regulated by the attachments of ethylenimine (EI) groups per polymer backbone and the normality ratio of [EI]/[Cu²⁺] used. It is found that the more EI-content per polymer backbone results in the smaller particle size and the narrower size dispersity of the colloidal Cu(0) particles, and the average particle size of 5.07 nm with standard deviation of 0.86 nm was obtained in the presence of D400(EI)₈ with the ratio of [EI]/[Cu²⁺] = 3. As the polymer concentration of D400(EI)₈ increases (the increase of [EI]/[Cu²⁺]), the average particle size of the prepared Cu(0) nanoparticle slightly changes, but interestingly, the size dispersity gradually decreases, where the standard deviation for the concentration at [EI]/[Cu²⁺] = 5 is 0.82 nm approaching that for monodispersed nanoparticles (0.5 nm).     

Synthesis of Ni/Al2O3 catalysts via alkaline polyol method and hydrazine reduction method for the partial oxidation of methane

Nickel catalysts supported on γ-Al₂O₃ were synthesized in the presence of polyvinylpyrrolidone (PVP) using both alkaline polyol method and hydrazine reduction method while fixing the weight ratio of [(PVP)]/[Ni(CH₃COO)₂·4H₂O] at 2. The effects of hydrazine [N₂H₅OH]/[Ni] and [NaOH]/[Ni] molar ratios on the structural properties of the catalysts were characterized by transmission electron microscopy (HRTEM) and by X-ray diffraction (XRD). The average of monodispersed Ni nanoparticles ranged between 8.0 and 13.0 nm. The catalytic tests were performed for the partial oxidation of methane in the temperature range of 600–800 °C under a flow rate of 157,500 L kg^–1 hr^–1 with CH₄/O₂= 2. At the molar ratio of [NaOH]/[Ni] = 2, the resultant nickel nanoparticles on alumina was established completely without impurities; thus, it demonstrated the highest catalytic activity, 88% for CH₄ conversion, and H₂ selectivity, 90.60%. The optimum [N₂H₅OH]/[Ni] ratio was determined as 4.1, which means a good catalytic performance and 89.35% selectivity to H₂ for the partial oxidation of methane.     

Influence of Confined Water on the Photophysics of Dissolved Solutes in Reverse Micelles

The photophysical parameters of two probes with largely different hydrophobic character, namely, coumarin 1 and coumarin 343, are investigated in sodium bis‐(2‐ethylhexyl)sulfosuccinate (AOT)/hexane/water reverse micelles at various water/AOT molar ratio w₀. Correlation of photophysical parameters such as fluorescence quantum yield, fluorescence lifetime, and emission maxima with w₀ indicate distinctly different trends below and above w₀≈7 for both probes. The variation of the average rotational correlation times obtained from fluorescence anisotropy decays for both probes in reverse micelles further corroborate the above observation. Similar studies were also performed in nonaqueous reverse micelles with acetonitrile as polar solvent. Similar to aqueous reverse micelles, breaks in the photophysical parameters with increasing acetonitrile/AOT molar ratios w′₀ were also observed in these cases, although at a much lower w′₀ value of 3. The present results indicate that around w₀≈7 for aqueous reverse micelles (and around w′₀≈3 for nonaqueous reverse micelles) a distinct change occurs in the probe microenvironment, which is rationalized on the basis of the relative populations of interfacial and core water. We propose that until the ionic head groups and counterions are fully solvated by polar solvents, that is, up to w₀≈7 (or w′₀≈3), the interfacial water population dominates. Above these molar ratios coalescence of excess water molecules with each other to form truncated H‐bonded water clusters leads to a sizable population of core water. This is further substantiated by changes in the IR absorption spectra for the O? D stretching mode of diluted D₂O in reverse micelles with varying w₀. Critical comparison of the present results with relevant literature reports provide clear support for the proposals made on water structure in reverse micelles. The role of relative size of the probe and the reverse micelles for differences in polar solvent to AOT ratios (w₀=7 and w′₀=3) in the observed breaks in the two types of reverse micelles is also discussed.     

Solvatochromic equilibria of cobalt(II) chloride in binary mixtures of dipolar aprotic solvents with water

The visible absorption spectra of CoCl₂ in binary mixtures of acetone, dmf, dma and dmso with H₂O show the existence of configuration equilibria between tetrahedral (T) and octahedral (O) species. Linear correlations between the values of log K (K = [O]/[T]) and the mole fraction of H₂O, _w, have been observed in all the systems under study; their slopes decrease linearly with an increase of the donor number, DN, of the organic component of the mixture. The formation of octahedral species is enthalpy favoured but entropy disfavoured. It was found that both H and S values change linearly with _w and the slopes of these relationships depend clearly on the DN values.     

Micellar solubilization of biopolymers in hydrocarbon solvents. I. a structural model for protein-containing reverse micelles

Three proteins (horse liver alcohol dehydrogenase, ribonuclease, lysozyme) were solubilized in hydrocarbon with the help of reverse micelles formed by aqueous di(2-ethyl-hexyl) sodium sulfosuccinate (AOT). Sedimentation and diffusion coefficients of the micellar aggregates were measured with an analytical ultracentrifuge. Partial specific volumes were also evaluated from density measurements. The molecular weight of the protein-containing reverse micelles (M _t ) could thus be determined for each protein system at various w₀ values (w₀ - [H₂O]/[AOT]). For horse liver alcohol dehydrogenase at w₀ = 46.4, for example,M _t is ca. 2,670,000 Daltons; for lysozyme at wo = 22.5,M _t is ca. 323,000 Daltons and increases by increasing w₀. On the basis of these experimentally determined molecular weights, a structural model for the protein-containing reverse micelle is proposed. The model is based upon the assumption that the protein is confined in the water pool of a spherical micelle, and that the inner core volume is the sum of the protein volume and the volume of all water molecules present in a micelle. It is possible then to calculate the micellar structure at each w₀ value. For example, in the case of ribonuclease at w₀ = 20, the inner core radius is ca. 37.5 A, and a layer of water of ca. 22 A separates the protein surface from the surfactant layer. The possible implications of this model for the reactivity of enzymes solubilized in hydrocarbons by reverse micelles are discussed.     

Synthesis of polyisobutylene with arylamino terminal group by combination of cationic polymerization with alkylation

The controlled cationic polymerization of isobutylene (IB) initiated by H₂O as initiator and TiCl₄ as coinitiator was carried out in n‐Hexane/CH₂Cl₂ (60/40, v/v) mixture at −40 °C in the presence of N,N‐dimethylacetamide (DMA). Polyisobutylene (PIB) with nearly theoretical molecular weight (M_n = 1.0 × 10⁴ g/mol), polydispersity (M_w/M_n) of 1.5 and high content (87.3%) of reactive end groups (tert‐Chlorine and α‐double bond) was obtained. The Friedel‐Crafts alkylation of triphenylamine (TPA) with the above reactive PIB was further conducted at different reactions, such as [TPA]/[PIB], solvent polarity, alkylation temperature, and time. The resultant PIBs with arylamino terminal group were characterized by ¹H NMR, UV, and GPC with RI/UV dual detectors. The experimental results indicate that alkylation efficiency (A_eff) increased with increases in [TPA]/[PIB], reaction temperature, and reaction time and with a decrease in solvent polarity. The alkylation efficiency could reach 81.0% at 60/40(v/v) mixture of n‐Hex/CH₂Cl₂ with [TPA]/[PIB] of 4.49 at 50 °C for 54 h. Interestingly, the synthesis of PIB with arylamino terminal group could also be achieved in one pot by combination of the cationic polymerization of IB initiated by H₂O/TiCl₄/DMA system with the successive alkylation by further introduction of TPA. Mono‐, di‐ or tri‐alkylation occurred experimentally with different molar ratio of [TPA]/[PIB]. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 936–946, 2008     

Kinetic Study of the Reaction of Leuco Methylene Blue with 2,6-Dimethyl-<Emphasis Type="Italic">p</Emphasis>-benzoquinone in a Reverse Micellar System

The kinetics of the reaction of leuco methylene blue (MBH) with 2,6-dimethyl-p-benzoquinone (DMBQ) were studied in a heptane/bis(2-ethylhexyl)-sulfosuccinate (AOT)/water reverse micellar system. The pseudo-first-order rate constant (k _obsd) obtained in the presence of excess of DMBQ was found to be proportional to the initial concentration of DMBQ for W ₀=3, 5, 10, 15 and 20 (W ₀=[H₂O]/[AOT]). The second-order rate constant (k ₂=k _obsd/[DMBQ]₀) increased with an increase in the W ₀ value, but was almost independent of the concentration of the water pool. A mechanism involving the distribution of DMBQ between the reverse micellar interface and bulk organic solvent was proposed to explain these findings.