Evaluation of volatile eluents and electrolytes for high-performance liquid chromatography-electrospray ionization mass spectrometry and capillary electrophoresis-electrospray ionization mass spectrometry of proteins. II. Capillary electrophoresis.

Peptides and proteins were separated by capillary electrophoresis (CE) in fused-silica capillaries coated with an irreversibly adsorbed monolayer of derivatized polystyrene nanoparticles. Whereas phosphate buffer, pH 3.10, enabled the highly efficient separation of basic proteins with plate counts up to 1,400,000 m-1, volatile buffer components such as formic acid or acetic acid titrated with ammonia to the desired pH had to be used for the direct coupling of CE with electrospray ionization mass spectrometry (ESI-MS). Compared to 40 mM phosphoric acid-sodium hydroxide, pH 3.10, a background electrolyte containing 125 mM formic acid-ammonia, pH 4.00, was shown to yield equivalent separation efficiency. Investigation of the influence of buffered electrolytes on the ESI-MS signal of lysozyme at pH 2.70-4.00 showed that the charge state distribution shifted to lower charge states at higher pH with a concomitant five-fold decrease in signal intensity of the most abundant signal. The presence of trifluoroacetic acid in the background electrolyte greatly increased the level of baseline noise and completely inhibited the observation of any mass signals related to proteins. Full scan spectra could be acquired from 50-500 fmol amounts of proteins during coupled CE-ESI-MS utilizing 100-125 mM formic acid-ammonia, pH 3.10. However, compared to UV detection, considerable band broadening is observed with ESI-MS detection which is mainly attributed to column overloading, band spreading in the interface, and scanning data acquisition. Finally, the major whey proteins beta-lactoglobulin A, beta-lactoglobulin B, and alpha-lactalbumin were identified in a whey drink by comparison of molecular masses determined by CE-ESI-MS to molecular masses calculated from the amino acid sequence.     

Size-exclusion chromatography--multiangle laser light scattering analysis of beta-lactoglobulin and bovine serum albumin in aqueous solution with added salt

The solution characteristics of beta-LGB (beta-lactoglobulin) and BSA (bovine serum albumin) are reported as determined by size-exclusion chromatography with on-line multiangle laser light scattering, differential refractive index and UV detection. The order of the three in series placed detectors as well as the interdetector volumes have been carefully pointed out. At concentrations below 2.5 mg/ml and at different values of pH the weight-average molecular mass of both proteins have been obtained. They indicate the appearance of monomers, dimers and higher order multimers. For beta-LGB the growth of self-associates could be observed at the isoelectric point over a period of days. The range of applicability of the method is discussed.     

Analysis of bovine whey proteins in soybean dairy-like products by capillary electrophoresis

The simultaneous separation of bovine whey proteins [alpha-lactalbumin and beta-lactoglobulin (A+B)] and soybean proteins was performed, for the first time, by capillary electrophoresis. Different experimental conditions were tested. The most suitable consisted of 0.050 M phosphate buffer (pH 8) with 1 M urea and 1.2 mg/ml methylhydroxyethylcellulose, UV detection at 280 nm, 15 kV applied voltage, and 30 degrees C temperature. Quantitation of bovine whey proteins in a commercial powdered soybean milk manufactured by adding bovine whey to its formulation was performed using the calibration method of the external standard. Direct injection of a solution of the powdered soybean milk only enabled quantitation of alpha-lactalbumin in the commercial sample. Detection of beta-lactoglobulin (A+B) required acid precipitation of the solution of the sample in order to concentrate bovine whey proteins in the supernatant prior to the analysis of this protein in the whey obtained. Since alpha-lactalbumin could also be quantitated from the injection of the whey, the simultaneous determination of alpha-lactalbumin and beta-lactoglobulin (A+B) was possible upon acid precipitation of the powdered soybean milk solution. Detection limits obtained were 14 microg/g sol. for alpha-lactalbumin and 52 microg/g sol. for beta-lactoglobulin (A+B) which represent protein concentrations about 60 microg/100 g sample for alpha-lactalbumin and 100 microg/100 g sample for beta-lactoglobulin (A+B).     

Protein determination by microchip capillary electrophoresis using an asymmetric squarylium dye: noncovalent labeling and nonequilibrium measurement of association constants

In response to a growing interest in the use of smaller, faster microchip (mu-chip) methods for the separation of proteins, advancements are proposed that employ the asymmetric squarylium dye Red-1c as a noncovalent label in mu-chip CE separations. This work compares on-column and precolumn labeling methods for the proteins BSA, beta-lactoglobulin B (beta-LB), and alpha-lactalbumin (alpha-LA). Nonequilibrium CE of equilibrium mixtures (NECEEM) represents an efficient method to determine equilibrium parameters associated with the formation of intermolecular complexes, such as those formed between the dye and proteins in this work, and it allows for the use of weak affinity probes in protein quantitation. In particular, nonequilibrium methods employing both mu-chip and conventional CE systems were implemented to determine association constants governing the formation of noncovalent complexes of the red luminescent squarylium dye Red-1c with BSA and beta-LB. By our mu-chip NECEEM method, the association constants K(assoc) for beta-LB and BSA complexes with Red-1c were found to be 3.53 x 10(3) and 1.65 x 10(5) M(-1), respectively, whereas association constants found by our conventional CE-LIF NECEEM method for these same protein-dye systems were some ten times higher. Despite discrepancies between the two methods, both confirmed the preferential interaction of Red-1c with BSA. In addition, the effect of protein concentration on measured association constant was assessed by conventional CE methods. Although a small decrease in K(assoc) was observed with the increase in protein concentration, our studies indicate that absolute protein concentration may affect the equilibrium determination less than the relative concentration of protein-to-dye.     

Characterization of quantum dot bioconjugates by capillary electrophoresis with laser-induced fluorescent detection

In this paper, we present a universal, highly efficient and sensitive method for the characterization of quantum dot (QD) bioconjugates based on capillary electrophoresis with laser-induced fluorescent (LIF) detection. We first prepared CdTe QDs in aqueous phase by a chemical route with mercaptopropionic acid as a ligand, and then were coupled to certain proteins using bifunctional linkage reagent or electrostatic attraction. The QD bioconjugates were characterized by capillary electrophoresis with LIF detection. We found that QD bioconjugates were efficiently separated with free QDs by the optimization of buffer pH. Furthermore, we found that ultrafiltration was an effective and simple approach to purify QD conjugates with bovine serum albumin (BSA). Due to their broad absorption spectra and size dependent emission wavelength tunability, QDs can be excited to emit different colour fluorescence using a single wavelength laser source, and therefore, we believe that CE with LIF detection will become a universal and efficient tool for the characterization of QD bioconjugates.     

Thermal Aggregation of Bovine Serum Albumin in Conventional Buffers: An Insight into Molecular Level Interactions

We have studied the effect of some conventional buffers, which are used frequently for biological research, on the thermal aggregation behavior of bovine serum albumin (BSA). The aggregation kinetics of BSA in buffer solutions were investigated by using UV–Vis spectroscopy. The buffers include sodium phosphate buffer, TRIS buffer and imidazole buffer at physiological pH (7.4). Dynamic light scattering and scanning electron microscopy have been employed to illustrate the size and morphology of protein aggregates. The molecular level interactions of buffer molecules with BSA was probed by various spectroscopic techniques, including UV–Vis, fluorescence, and circular dichroism. The results of this study reveal that the strong interactions of the buffers with protein’s folded/unfolded structures lead to stabilization/destabilization of BSA. We have also explored the possible binding sites of BSA for these buffers using a molecular docking technique.     

Enhanced detection of porphyrins by capillary electrophoresis-laser induced fluorescence

A highly sensitive technique for the analysis of urinary porphyrins using capillary electrophoresis (CE) coupled with laser-induced fluorescence (LIF) detection is reported. Separation of mesoporphyrin IX, coproporphyrin, uroporphyrin and the penta-, hexa- and heptacarboxylic acid porphyrins was achieved in 11 min using a 10 mM 2-(N-cyclohexylamino)ethanesulfonic acid (CHES, pH 10) -75 mM sodium dodecyl sulfate (SDS) buffer. Migration time and peak area repeatability were less than 1 and 5% relative standard deviation (RSD), respectively. Limits of detection of 20 pM (2 x 10(-11) M) were achieved employing the recently introduced Nichia violet diode laser for excitation at 400 nm. This represents an enhancement in sensitivity of over two orders of magnitude compared to previous reports. This high sensitivity for urinary porphyrins was demonstrated through the quantification of coproporphyrin and uroporphyrin in urine samples after up to a 100-fold dilution.     

Recent advances in affinity capillary electrophoresis

Use of the specificity of (bio)interactions can effectively overcome the selectivity limitation faced in capillary electrophoresis (CE), and the resulting technique usually is referred to as affinity capillary electrophoresis (ACE). Despite the high selectivity of ACE, several important problems still need to be addressed. A major issue in all CE separations, including ACE, is the concentration detection limit. Using UV detection, this is usually in the order of 10(-6) M whereas laser-induced fluorescence (LIF) detection can provide detection limits down to the sub-10(-10) M range. However, a marked disadvantage of LIF is that labeling of the analytes is usually required, which might change the interaction behavior of the solutes under investigation. Additionally, labeling reactions at sub-10(-10) M concentration levels are certainly not trivial and often difficult to perform quantitatively. Alternative and universal detection approaches, particularly mass spectrometric (MS) detection, look very promising but (A) CE-MS techniques are still far from routine application. Important future progress in sensitive detection strategies is likely to increase the use of ACE in the future.     

High-sensitivity laser-induced fluorescence detection of native proteins in capillary electrophoresis.

A highly sensitive laser-induced (LIF) detection scheme for native, tryptophan- or tyrosine-containing proteins in capillary electrophoresis (CE) has been demonstrated. The 275.4 nm line from an argon-ion laser is used to excite native protein fluorescence. A limit of detection (LOD) (S/N = 2) of 1 x 10(-10) M for conalbumin represents a 140-fold improvement over earlier reports. With stacking at injection, the LOD is 3 x 10(-12) M. Linear dynamic ranges of at least 5 and 4 orders of magnitude for, respectively, tryptophan and bovine serum albumin are found. The practical performance and blueprint of an easily constructed, rugged, compact and user-friendly LIF detector for CE are shown.     

Capillary electrophoresis with a UV light-emitting diode source for chemical monitoring of native and derivatized fluorescent compounds

We report the utilization of a high power UV light-emitting diode for fluorescence detection (UV-LED-IF) in CE separations. CE-UV-LED-IF allows analysis of a range of environmentally and biologically important compounds, including PAHs and biogenic amines, including neurotransmitters, amino acids, proteins, and peptides, that have been derivatized with UV-excited fluorogenic labels, e.g., o-phthalic dicarboxaldehyde/beta-mercaptoethanol (OPA/beta-ME). The 365 nm UV-LED was used as a stable, low cost source for detection of UV-excited fluorescent compounds. UV-LED-IF was used with both zonal CE separations and MEKC. Native fluorescence detection of PAHs was accomplished with detection limits ranging from 10 nM to 1.3 microM. Detection limits for OPA/beta-ME-labeled glutamic acid and aspartic acid were 11 and 10 nM, respectively, for off-line labeling, and 47 and 47 nM, respectively, for on-line labeling, comparable to UV-laser-based systems. Analysis of OPA/beta-ME-labeled proteins and peptides was performed with 28 and 47 nM detection limits for BSA and myoglobin, respectively.     

Sensitive, label-free protein assay using 1-ethyl-3-methylimidazolium tetrafluoroborate-supported microchip electrophoresis with laser-induced fluorescence detection

Based on the dimer-monomer equilibrium movement of the fluorescent dye Pyronin Y (PY), a rapid, simple, highly sensitive, label-free method for protein detection was developed by microchip electrophoresis with LIF detection. PY formed a nonfluorescent dimer induced by the premicellar aggregation of an anionic surfactant, SDS, however, the fluorescence intensity of the system increased dramatically when proteins such as BSA, bovine hemoglobin, cytochrome c, and trypsin were added to the solution due to the transition of dimer to fluorescent monomer. Furthermore, 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF4) instead of PBS was applied as running buffers in microchip electrophoresis. Due to the excellent properties of EMImBF4, not only nonspecific protein adsorption was more efficiently suppressed, but also approximately ten-fold higher fluorescence intensity enhancement was obtained than that using PBS. Under the optimal conditions, detection limits for BSA, bovine hemoglobin, cytochrome c, and trypsin were 1.00x10(-6), 2x10(-6), 7x10(-7), and 5x10(-7) mg/mL, respectively. Thus, without covalent modification of the protein, a protein assay method with high sensitivity was achieved on microchips.     

Protein labeling with red squarylium dyes for analysis by capillary electrophoresis with laser-induced fluorescence detection

Two new red luminescent asymmetric squarylium dyes (designated "Red-1c and Red-3") have been shown to exhibit absorbance shifts to longer wavelengths upon the addition of protein, along with a concomitant increase in fluorescence emission. Specifically, the absorbance maxima for Red-1c and Red-3 dyes are 607 and 622 nm, respectively, in the absence of HSA, and 642 and 640 nm in the presence of HSA, making the excitation of their protein complexes feasible with inexpensive and robust diode lasers. Fluorescence emission maxima, in the presence of HSA, are 656 and 644 nm for Red-1c and Red-3, respectively. Because of the inherently low fluorescence of the dyes in their free state, Red-1c and Red-3 were used as on-column labels (that is, with the dye incorporated into the separation buffer), thus eliminating the need for sample derivatization prior to injection and separation. A comparison of precolumn and on-column labeling of proteins with these squarylium dyes revealed higher efficiencies and greater sensitivities for on-column labeling, which, when conducted with a basic, high-salt content buffer, permitted baseline resolution of a mixture of five model proteins. LOD for model proteins, such as transferrin, alpha-lactalbumin, BSA, and beta-lactoglobulin A and B, labeled with these dyes and analyzed by CE with LIF detection (CE-LIF) were found to be dependent upon dye concentration and solution pH, and are as low as 5 nM for BSA. Satisfactory linear relationships between peak height (or peak area) and protein concentration were obtained by CE-LIF for this on-column labeling method with Red-3 and Red-1c.     

Capillary Electrophoresis Based Immunoassay for Monoclonal Antibody with Diode Laser Induced Fluorescence Detection

ABSTRACT

A capillary electrophoresis based immunoassay (CEIA) for monoclonal antibody using diode laser induced fluorescence (LIF) detection was described. A direct assay for monoclonal anti-BSA in mouse serum was used as a model. BSA was labeled with Cy5 and used as the immunoreagent. The 635 nm line of a diode laser was used as the excitation source for LIF detection. The calibration curve for anti-BSA in mouse serum had a linear dynamic range of 4-40 nM. The concentration limit of detection (LOD) was 1.2 nM. Incubation time and CE conditions such as buffer concentration, pH and separation voltage were optimized, and the performances of different lasers as excitation sources were also compared.     

Studying protein-drug interaction by microfluidic chip affinity capillary electrophoresis with indirect laser-induced fluorescence detection

We developed a microfluidic chip-affinity CE method based on indirect LIF detection to study protein-drug interactions. The interaction between heparin and BSA was quantitatively studied, as a model system. In our method, sodium fluorescein was chosen as background, and redistilled water as marker to monitor EOF. The electrophoretic mobility changes of BSA were measured, with various concentrations of heparin added to the running buffer. Each run was completed within 80 s. The binding constant was determined to be (1.24 +/- 0.05) x 10(3) M(-1), which was in good agreement with that reported in the literature.     

A fresh look into background electrolyte selection for capillary electrophoresis‐laser induced fluorescence of peptides and proteins

This study reports a reinvestigation of background electrolyte selection strategy for performance improvement in CE‐LIF of peptides and proteins. This strategy is based on the employment of high concentrations of organic species in BGE possessing high buffer capacity and low specific conductivity in order to ensure excellent stacking preconcentration and separation resolution of fluorescently tagged peptides and proteins. Unlike universal UV detection, the use of such BGEs at high concentrations does not lead to degradation of LIF detection signals at the working excitation and emission wavelengths. At the same buffer ionic strength, pH and electric field, an “inorganic‐species‐free” BGE (or ISF BGE) for CE‐LIF of fluorescently labeled beta amyloid peptide Aβ 1–42 (a model analyte) offered a signal intensity and peak efficiency at least three‐times higher than those obtained with a conventional BGE normally used for CE‐LIF, while producing an electric current twice lower. Good peak performance (in terms of height and shape) was maintained when using ISF BGEs even with samples prepared in high‐conductivity phosphate buffer saline matrix. The advantageous features of such BGEs used at high concentrations over conventional ones in terms of high separation resolution, improved signal intensities, tuning of EOF magnitudes and minimization of protein adsorption on an uncoated fused silica capillary are demonstrated using Alexa‐488‐labelled trypsin inhibitor. Such BGE selection approach was applied for investigation of separation performance for CE‐LIF of ovalbumin labelled with different fluorophores.     

System Peaks of Cyclodextrins in Capillary Electrophoresis

Using a running buffer containing cyclodextrins (CDs) and 2‐[N‐cyclohexylamino]‐ethanesulfonic acid (CHES), positive system peaks were observed in the analysis of a ganglioside mixture by CE‐UV. These system peaks were related to CDs in the running buffer because these peaks were also detected when a plug of solution devoid of CDs but having the same CHES concentration and pH as the running buffer was injected. Neutral CDs were separated owing to the formation of inclusion complexes with the anionic CHES ion. One possible explanation for the positive system peaks is that the anionic CD‐CHES inclusion complex is displaced by co‐ions with higher UV absorptivity.     

Comprehensive two-dimensional separation system by coupling capillary reverse-phase liquid chromatography to capillary isoelectric focusing for peptide and protein mapping with laser-induced fluorescence detection

A comprehensive two-dimensional (2-D) separation system, coupling capillary reverse-phase liquid chromatography (cRPLC) to capillary isoelectric focusing (CIEF), is described for protein and peptide mapping. cRPLC, the first dimension, provided high-resolution separations for salt-free proteins. CIEF, the second dimension with an orthogonal mechanism to cRPLC afforded excellent resolution capability for proteins with efficient protein enrichment. Since all sample fractions in cRPLC effluents could be transferred to the CIEF dimensions, the combination of the two high-efficiency separations resulted in maximal separation capabilities of each dimension. Separation effectiveness of this approach was demonstrated using complex protein/peptide samples, such as yeast cytosol and a BSA tryptic digest. A peak capacity of more than 10 000 had been achieved. A laser-induced fluorescence (LIF) detector, developed for this system, allowed for high-sensitive detection, with a fmol level of peptide detection for the BSA digest. FITC and BODIPY maleimide were used to tag the proteins, and the latter was found better both for separation and detection in our 2-D system.     

Simultaneous separation and quantitation of the major bovine whey proteins including proteose peptone and caseinomacropeptide by reversed-phase high-performance liquid chromatography on polystyrene-divinylbenzene

A precise, sensitive and reliable RP-HPLC method was developed to enable not only unequivocal determination of alpha-lactalbumin and beta-lactoglobulin in bovine whey samples, but also simultaneous measurement of proteose peptone, caseinomacropeptide, bovine serum albumin and immunoglobulin G. The optimised method on the Resource RPC column allowed separation of the proteins in 30 min and could be applied to the analysis of soluble proteins in a variety of commercial and laboratory whey products. Furthermore, some qualitative information on protein heterogeneity and quality could be derived from the RP-HPLC analyses with additional data available from on-line electrospray mass spectrometry. Within- and between-day repeatability over a wide range of concentrations was excellent (RSD< or =5%) for all proteins except immunoglobulin G and bovine serum albumin where RSD was 7-10%. Analysis of grouped data from whey protein concentrate and whey protein isolate samples gave a limit of detection of < or =0.3% powder mass and a limit of quantitation of < or =1.0% powder mass for all proteins except immunoglobulin G. Limits of detection and quantitation were 0.6% and 2.0%, respectively, for this protein. Quantitative data obtained by the RP-HPLC method compared very favourably with data obtained by alternative methods of whey protein analysis.     

Improved method for the simultaneous determination of whey proteins, caseins and para-kappa-casein in milk and dairy products by capillary electrophoresis

A capillary electrophoresis method for the simultaneous determination of whey proteins, caseins and their degradation products, such as para-kappa-casein, was proposed. The effect of several parameters (pH, ionic strength and concentration of urea in the electrophoresis buffer and applied voltage) on the analysis time and on the separation efficiency of the major milk proteins was studied. Using a hydrophilically coated capillary, in combination with electrophoresis buffer 0.48 M citric acid-13.6 mM citrate-4.8 M urea at pH 2.3, and a separation voltage of 25 kV, a complete separation of beta-lactoglobulin and para-kappa-casein was achieved, permitting the quantification of both components.     

Method Development of Enantiomer Separations by Affinity Capillary Electrophoresis,Cyclodextrin Electrokinetic Chromatography and Capillary Electrophoresis-Mass Spectrometry

 Capillary electrophoresis (CE) has become a powerful tool for enantiomer separations during the last decade. Since 1993, the author has investigated enantiomer separations by affinity capillary electrophoresis (affinity CE) with some proteins and by cyclodextrin electrokinetic chromatography (CDEKC) with some charged cyclodextrins (CDs). Many successful enantiomer separations are demonstrated from our study in this review article. In the enantiomer separations by affinity CE, the deterioration of detection