过滤成膜制备氧化铝中空纤维超滤膜

 介绍了在α－Al2O3中空纤维微滤膜上采用过滤成膜技术制备γ－Al2O3超滤膜的方法．应用热重分析、差热分析、X射线衍射和扫描电子显微镜等测试手段对膜的热稳定性、结构及形貌进行了表征．扫描电子显微镜结果表明，采用过滤成膜方式制备的担载中空纤维超滤膜表面无针孔，无裂纹．气体渗透实验进一步表明，所得中空纤维超滤膜完整、无缺陷，具有一定的气体选择性．经700℃焙烧后的膜在0．3和0．4MPa条件下对氮／氩的分离因子分别为1．133和1．139，说明气体通过膜的扩散以Knudsen扩散传质为主．用等温氮气吸附实验测定了非担载膜的孔径大小和分布，其比表面积为228．9m2／g，最可几孔径约为4．5nm．     

Phase Development in Sol Derived Microporous Membranes for Gas Permselectivity

A sol-gel route has been used to produce a nanoporous membrane for the separation of greenhouse gases from power plants at elevated temperatures (700–900 K). The membrane has a controlled pore size distribution and is multiphasic, in order to prevent grain growth and pore coarsening. The alumina/titania diphasic ceramic was obtained from alkoxide precursors with additional magnesium or lanthanum doping to stabilize low temperature phases and to provide possible chemisorption of CO2. It was found that both Mg and La stabilized the -alumina phase to higher temperature by as much as 200 K, although Mg is less effective.     

Development of Anti-Reflection (AR) Coating on Plastic Panels for Display Applications

Traditionally, various vacuum-based processes have been used for producing interference-type anti-reflection (AR) coatings on large area substrates for different commercial applications. In this paper, the development of sol-gel derived AR coating on large plastic substrates for display application is presented. The sol-gel dip coating process was used to deposit thin films on large size plastic panels. By developing sols with different refractive indices, multi-layer thin-film AR coating stacks were designed and fabricated. These coatings possess good uniformity and meet stringent automotive specifications. This technology has been commercialized successfully for dashboard instrument panel application in Toyota's new hybrid engine car, named Prius.In this paper, AR coatings prepared by the sol-gel process are reviewed. The basic design concept for an AR coating, the coating preparation procedure, and important parameters of the solution coating process are discussed. Optical constants of the coating materials were characterized by using spectroscopic ellipsometry. Optical, mechanical and environmental tests were performed on the sol-gel derived AR coating stack. The sol-gel derived AR coating possesses equivalent or superior properties when compared to the major commercially available AR coating products.     

Silica Coating on Colloidal Maghemite Particles

Maghemite colloidal particles are coated with a silica layer using a silicon alkoxide as silica precursor. The coating process is studied by electrophoresis, quasi-elastic light scattering, nitrogen adsorption, and infrared spectrometry analyses. The conditions of complete coverage of the iron oxide particles by silica and the nature of the maghemite–silica interface are discussed.     

Sol–Gel Coating of Thin Display Glasses - Problems and Remedy

Evaporation cooling is an inevitable but often neglected concomitant effect of sol–gel dip coating and related techniques, which is responsible for occasional coating problems. The phenomenon, however, emerges mostly for thin substrates of less than 1 mm thickness as the heat capacity of the substrate - the main source of heat for the evaporation - is reduced. The cooling of the substrate results in a reduced evaporation rate and an increased humidity in the surroundings of the film, leading to demixing of liquid components and an uncontrolled hydrolysis. The resulting coatings exhibit a hazy and cloudy appearance with crater-like structures in the micron range and consequently, functional properties such as the electrical conductivity of ATO coatings (antimony-doped tin oxide, SnO₂:Sb) are unsatisfactory. Among a variety of measures to overcome this cooling problem, a moderate heating of the coating liquid to only 25_°C was found to be the method of choice to obtain high quality sol–gel thin films on substrates with a thickness down to 0.4 mm as required for display applications. This slight modification of the dip coating processing helps to reduce the susceptibility of the wet film to humidity and to improve the coating quality and the reproducibility in general - both on thin and thick substrates.     

金属基体上铝溶胶涂层的制备

 以拟薄水铝石为原料,采用HNO3胶溶法制备了铝溶胶,研究了制备条件对胶体性质的影响. 结果表明,拟薄水铝石的含量和HNO3的加入量是影响胶体粒度大小、粒径分布以及胶体稳定性的重要因素. 当拟薄水铝石的含量为4.5%~5.5%、酸加入量为［H+］/［AlOOH］=0.08~0.1(摩尔比)时,可以得到颗粒度小(平均粒径≤19.3 nm),粒径分布范围窄(4.1~53 nm)和稳定性好的胶体溶液. 以该胶体为过渡涂层涂覆在金属基体上. 在能形成稳定胶体的前提下,酸度相同时,胶体的浓度越大,粘度越大,涂覆到基体上的量就越多; 但是过渡涂层的牢固度似乎与胶体的浓度关系不大. 金属基体的前处理条件也是一个重要的因素,它不仅影响过渡层的涂覆量,也影响涂层的牢固度.     

Polymerized Lyotropic Liquid Crystal Assemblies for Membrane Applications

Cross‐linked lyotropic liquid crystal (LLC) assemblies represent a new class of polymer materials for membrane applications. These materials are formed by the phase‐segregation and self‐assembly of polymerizable amphiphiles in water into condensed ordered ensembles that can be cross‐linked in situ with retention of microstructure. The resulting LLC polymer networks have ordered, nanometer‐scale aqueous and cross‐linked organic domains, which can be used to affect gas solubility and diffusivity through the polymer to help separate molecules via the solution–diffusion mechanism. The open aqueous domains can also be used for pore transport and size exclusion with resolution on the molecular size level. The use and application potential of cross‐linked LLC assemblies as gas separation membranes, selective vapor barrier materials, and water nanofiltration and desalination membranes are presented.

     

混合导电型陶瓷透氧膜材料的化学稳定性

考察了Sr-Co -Fe -O系列和Bi-Sr-Fe -O系列混合导电型无机透氧膜材料在氧分压小于 1.0 13Pa的气氛中 ,在 850℃和 950℃高温下加热 2 4～ 10 0h前后结构的变化。发现Bi -Sr -Fe-O系列透氧膜材料具有良好的化学稳定型 ,可以用于还原气氛下的催化反应。     

Modified Silica Sol Coatings for Water-Repellent Textiles

The preparation of water repellent textiles by coating with different modified silica sols has been investigated. For this, pure and with 3-glycidoxypropyl triethoxysilane co-condensed silica sols were modified by three types of additives: alkyltrialkoxysilanes, polysiloxane derivatives and a fluorine containing silane. Hydrophobic properties of the coated fabrics of polyamide and of polyester mixed with cotton were determined using contact angle measurements. The hydrophobicity increases with increasing concentration of the alkylsilane additive in the silica sol and the length of the alkyl chain but with high additive concentrations plateau values in hydrophobicity were reached. Analogously textile coatings with high hydrophobicity were gained using hydrophobic polysiloxane or fluorine containing silicon compounds. The comparison of the different variants reveals that high wash-out stabilities were reached only by silica sols containing fluorine compoundsand hexadecylsilane additives. Therefore long-chain alkyltrialkoxysilane compounds could be used as substitutes for fluorine compounds for the surface modification of textiles in some practical applications.     

介孔氧化硅膜在多孔陶瓷载体上的组装

采用过滤成膜方式结合溶剂挥发诱导自组装方法在多孔氧化铝中空纤维上制备了介孔氧化硅膜。XRD、TEM和N₂吸附脱附实验结果显示非担载膜具有有序的六方介孔结构。通过对中空纤维担载膜的XRD分析进一步确认介孔氧化硅膜的形成。SEM和EDS线扫描结果显示制备的担载膜表面完整、无缺陷,膜层和载体界面之间结合紧密。在此基础上对介孔膜在多孔陶瓷载体上的形成机理进行了探讨。     

Formation of Superhydrophobic Alumina Coating Films with High Transparency on Polymer Substrates by the Sol-Gel Method

Transparent, superhydrophobic coating films have been prepared on polymer substrates at low temperatures through the sol-gel method. Al₂O₃ gel films were prepared on poly(ethylene terephthalate) substrates from Al(O-sec-C₄H₉)₃ chemically modified with ethyl acetoacetate. A small roughness of about 20–50 nm was found to form on the surface of the Al₂O₃ gel films dried at room temperature and then immersed in hot water at 60°C. The electron diffraction measurements have shown that this roughened surface consists of pseudoboehmite nanocrystals. The coating of hydrolyzed fluoroalkyltrimethoxysilane on the Al₂O₃ gel films with the small roughness produced transparent, superhydrophobic films with contact angle for water larger than 150°.     

金属有机框架材料在质子交换膜燃料电池中的潜在应用

金属有机框架亦称作多孔配位网状结构,是一种多孔晶态材料,具有结构可设计、孔壁可功能化修饰、高度晶态化、比表面积大及优良的导电性等诸多优点,使其在能源转换及储存方面备受关注。本文详细介绍了新型金属有机框架质子导体及电催化剂在燃料电池方面的相关研究;综述了国内外近年来在金属有机框架质子交换膜和氧还原电催化领域所取得的一些重要进展,例如金属有机框架质子交换膜电导率可高达1.82 S·cm^-1（70℃,90% RH）,金属有机框架电催化剂作为阴极在膜电极测试中可产生0.91 W·cm^-2（0.6 V）的峰值功率密度;并指出了金属有机框架在质子交换膜和电催化剂研究中存在的问题,这为今后开发高电导性质子交换膜和高催化活性电催化提供了新思路。     

Thermal Behaviour of a TiO2—ZrO2 Microcomposite Prepared by Chemical Coating

A microcomposite powder in the system TiO₂—ZrO₂ as a precursor of zirconium titanate (ZT) materials has been studied by thermal methods (DTA-TG) and X-ray diffraction (XRD). The microcomposite powder has been prepared by chemical processing of crystalline TiO₂ (rutile, 10 mass% anatase),as inner core, coated with in situ precipitated amorphous hydrated zirconia gel, asouter core. The morphology and chemical composition of the resultant powders has been examined by SEM-EDX (Scanning electron microscopy-energy dispersive X-ray spectroscopy). Thermal behaviour of the microcomposite powder was reported, showing the dehydration and dehydroxylation of the zirconia gel, the crystallization into metastable cubic/tetragonal zirconia at temperatures 400—470°C, and the feasibility of preparing ZT powder materials by progressive reaction of TiO₂ and ZrO₂ at higher temperatures (1400°C).This revised version was published online in November 2005 with corrections to the Cover Date.     

TiO2微粒功能化多孔Al2O3膜的光电化学研究

用恒电位法制备了多孔Al2O3薄膜,通过在Al2O3薄膜孔内水蒸汽水解钛酸异丙酯生成了锐钛矿型TiO2微粒,制备出了Al2O3与TiO2微粒的复合薄膜．用XRD,SEM,光电化学方法进行了研究．实验表明：该复合薄膜具有光电转换特性,在光催化、光电化学太阳能转换中具有应用价值．     

稀土对WC颗粒增强铁基体复合涂层组织结构的影响

采用氩弧熔覆技术在45号钢表面制备一层稀土WC颗粒增强铁基体耐磨复合涂层。通过扫描电镜(SEM)、X射线衍射(XRD)和能谱仪(EDS)等测试分析手段研究了稀土的引入对复合涂层中基体组织及碳化物的影响,并与未加稀土进行了比较。结果表明:引入稀土后,一方面优化了熔覆层组织中碳化物颗粒分布,降低了熔覆层组织中碳化物颗粒的团聚、桥接,且颗粒分布均匀;另一方面改善了熔覆层的组织,细化晶粒,减弱了熔覆过程中产生的树状晶,抑制了WC颗粒的溶解和鱼骨状碳化物的生成。在熔覆层组织中碳化物颗粒相主要有三种存在形式:原始未熔WC颗粒、与基体形成的复式碳化物及在凝固过程中重新结晶的W2C(或WC)。     

Effect of Nd-doping on the Thermal Stability and Pore-structure of Al2O3 Membranes

Unsupported Nd-doped Al2O3 membranes have been prepared with a sol-gel treatnt by using aiuminium isopropoxide and Nd(NO3)3 as the main raw materials. The properties of Nd-doped Al2O3 membranes were characterized by XRD, DTA-TG, IR and N2 adsorption. The effects of Nd-doping on the phase composition, thermal stability as well as applications of porestructure of Nd-doped Al2O3 membranes at high temperature were discussed. The results show that Nd-doping can raise the transition temperature rom γ-Al203 to α-Al2O3, enhance the thermal stability of Al2O3 membranes, and evidently improve the pore-structural parameters of Al2O3 membranes applied at higher temperatures.     

Optical Viscometry of Spinning Sol Coatings

Optical interferometric monitoring of spin coating (optospinography) has allowed close observation of the temporal evolution of a thin silicate sol film (typically at 2000 rpm, 100 Hz data acquisition). The kinematic viscosity data obtained, using a simple analytical model, are validated with those from a mineral oil standard, with agreement well within the experimental uncertainties. For spin coating in open air, the influence of variations in refractive index, rheological properties and air flow are discussed. Inflections in the temporal evolution of the optical thickness of silicate sol films are analyzed, which indicate the usefulness of optospinography, particularly when applied in the proximity of the rotation axis and evaporation is minimized, to monitor time variations in the kinematic viscosity of these sols during spin coating.     

Coating of oxide powders with alkoxide derived zirconia

Coating of alumina powders with tetragonal zirconia grains in the nanometric size range was obtained from a modified zirconium n-propoxide sol.Powder sedimentation observations and washing experiments were performed to show modifications of particles surface. Amorphous precursor film formation and crystalline zirconia coating were characterized by transmission electron microscopy. Crystallographic relationships between zirconia and alumina particles were also observed.     

均分散氧化铜胶体粒子制备的研究

近年来,对均分散体系即分散相粒子大小形状均一体系的研究有了飞速发展.本文报道用几种铜盐制备均匀的氧化铜胶体微粒所需的条件,并对胶体粒子生成过程进行了探讨. 1 实验部分 1.1试剂与仪器 所有药品均为分析纯,水是二次蒸馏水,所配制的溶液都经4号玻璃砂漏斗过滤后使用.JEOL型电镜为日本电气公司产品.     

Self‐assembly of Carbon Particles as a Heat Sink Coating to Promote Radiative Cooling

Novel composite carbon particles are developed that can self‐assemble as a coating on a substrate without a binder. These carbon particles were used as a coating to enhance thermal dissipation and their thermal conductivity, surface emissivity and cooling performance were measured. Carbon particles with both thiol and epoxy functional groups self‐assembled to form a coating on the surface of a heat sink without a binder, which greatly improved the thermal conductivity of the coating. Coating a heat sink with the carbon particles yielded a higher thermal conductivity and emissivity than could be obtained with the addition of binder in the conventional approach, and significantly enhanced the cooling performance. In addition, the cooling performance of the carbon nanotube outperformed all other particles when coated on a substrate, because it had the highest thermal conductivity and good radiation emissivity. We developed an equation to describe the various parameters affecting the cooling performance of the thermally dissipative coating. This equation was confirmed by the experimental data.