Determination of water soluble trace metals in airborne particulate matter using a dynamic extraction procedure with on-line inductively coupled plasma optical emission spectrometric detection

A novel continuous-flow system for the dynamic extraction of water soluble metal fractions in airborne particulate matter (APM) with subsequent inductively coupled plasma optical emission spectrometric (ICP-OES) analysis of derived extracts is presented. The fully automated extraction system with on-line multi-element detection offers enhanced sensitivity when compared to batch-wise counterparts; additionally it provides information about the extraction process. With the developed procedure detection limits in the order of 1.5 (Ba) to 8.0 (Ni) ng extractable mass per investigated sample could be achieved, which translates to method detection limits for soluble metal concentrations in APM ranging from 0.2 ng m⁻³ (Ba) to 0.9 ng m⁻³ (Fe). Reproducibility of analysis was determined by replicate measurement (n = 6) of an APM sample with an aerodynamic diameter ≤10 μm (PM10), derived results varied between 3.5% (Mn) and 12.1% (Ni) relative standard deviation. Method validation was accomplished by comparison of extracted soluble and remaining non-soluble fractions with the total metal contents of the investigated PM10 samples, showing an excellent mass balance for all elements. Application of the developed procedure for the analysis of water soluble metal fractions in PM10 samples (n = 16) from Linz (Austria) indicated a high variability of extractable fractions ranging from 11.7 ± 7.2% (Fe) to 48.8 ± 15.4% (Mn) of the total metal contents.     

Inductively coupled plasma atomic emission spectrometric determination of 27 trace elements in table salts after coprecipitation with indium phosphate

The coprecipitation method using indium phosphate as a new coprecipitant has been developed for the separation of trace elements in table salts prior to their determination using inductively coupled plasma atomic emission spectrometry (ICP-AES). Indium phosphate could quantitatively coprecipitate 27 trace elements, namely, Be, Ti, Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd, Pb, Sc, Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, and Lu, in a table salt solution at pH 10. The rapid coprecipitation technique, in which complete recovery of the precipitate was not required in the precipitate-separation process, was completely applicable, and, therefore, the operation for the coprecipitation was quite simple. The coprecipitated elements could be determined accurately and precisely by ICP-AES using indium as an internal standard element after dissolution of the precipitate with 5 mL of 1 mol L⁻¹ nitric acid. The detection limits (three times the standard deviation of the blank values, n = 10) ranged from 0.001 μg (Lu) to 0.11 μg (Zn) in 300 mL of a 10% (w/v) table salt solution. The method proposed here could be applied to the analyses of commercially available table salts.     

无滤共沉淀富集-等离子体原子发射光谱法测定痕量稀土元素

以编结反应器 (KR)作为反应场所,用NH3～NH4NO3缓冲溶液在线沉淀、富集,电感耦合等离子体原子发射光谱法(ICP-AES)检测稀土元素,系统地研究了稀土元素在线沉淀及溶解的最佳条件.实验结果表明:在80 ℃时,稀土离子与pH 9.0的NH3～NH4NO3缓冲溶液在线混合后经2 m KR富集120 s,用1 mol/L HNO3以1.0 mL/min流速洗脱时富集效果最好,富集倍数可达52～76倍,进样频率为10/h.同时考察了共存离子的干扰及其消除方法.方法的稀土元素的检出限为0.07～1.23 μg/L,精密度RSD在1.7%～4.3%之间(n=6),线性范围2～10 μg/L.应用于标准样品中痕量稀土元素的测定,其测定值与标准值吻合.     

Determination of water-soluble and insoluble compounds in size classified airborne particulate matter

The elemental composition of water soluble and acid soluble size-fractionated airborne particulate matter (APM) was investigated. PM2.5 and PM2.5-10 samples were collected every three days from October 2006 to October 2007 in Buenos Aires, Argentina. The collection was performed on Nucleopore® filters using a GENT sampler. Samples containing fine and coarse particles were subjected to an aqueous leaching to obtain information on the dissolution behaviors of ions, metal and metalloids. Key elements namely, Al, Ba, Ca, Cr, Cu, Fe, Mg, Mn, Pb, Se, Ti and Zn were determined in each fraction by inductively coupled plasma optical emission spectrometry (ICP OES). In the aqueous fractions, Cl⁻, SO₄²⁻, Na⁺ and NH₄⁺ were determined by high performance liquid chromatography (HPLC). A (6:2:5) mixture of nitric, hydrochloric and perchloric acids was used for leaching metals from the residual filters. For validation of the extraction procedure, the ICP OES measurements the Standard Reference Material NIST 1648 (Urban particulate matter) was subjected to the same analytical procedure that the samples loaded with APM. Total analyte concentration varied from 333.2 μg g^− 1 (equivalent to 3.7 ng m^− 3) for Ti to 692 mg g^− 1 (equivalent to 2.47 μg m^− 3) for Ca.     

Multi-element analysis of airborne particulate matter by various spectrometric methods after microwave digestion

A microwave digestion procedure in combination of the measurement of various spectrometric methods including atomic absorption spectrometry, inductively coupled plasma atomic emission spectrometry and inductively coupled plasma mass spectrometry was developed for the multi-element analysis of airborne particulate matter collected on PTFE filters by a dichotomous sampler. In order to achieve more sensitive and rapid multi-element analyses, special PTFE-lined digestion vessels were used. It was found that complete digestion of airborne particulates with an acid mixture of HNO₃-HClO₄-HF (3:7:1, v/v) can be achieved in the microwave-irradiated closed vessel system and direct spectroscopic measurement of the digested sample after appropriate dilution. A recovery study was conducted using a multi-element standard and NIST Standard Reference Material 1648 Urban Particulate. Sixteen major, minor, and trace elements in airborne particulate matter were determined.     

Analysis of nickel-niobium alloys by inductively coupled plasma optical emission spectrometry

Inductively coupled plasma optical emission spectrometry (ICP-OES) was applied to the analysis of major and minor elements of Ni-Nb alloys obtained by aluminothermic reduction process. Digestion of samples was made using a mixture of HF+HNO₃. Minor and trace elements were determined without matrix separation. The precision for all constituents was <3%. Recoveries for the analyte-spiked samples were 95%.     

ICP-AES 法测定硅铁中痕量元素

采用电感耦合等离子原子发射光谱法测定硅铁中的痕量元素,研究了 Fe 基体对被测元素的影响,并选择了最佳工作条件.被测元素的检测限为 0 .60～76.2 ng/mL,样品加标回收率为 92%～108%,RSD(n=8)<3%.     

Inductively coupled plasma optical emission spectrometric determination of trace elements in sediments after sequential selective extraction: effects of reagents and major elements on the analytical signal

The interfering effects due to the reagents and matrix elements associated with a four step sequential extraction procedure on ICPOES determination of trace elements were investigated in a systematic way. The emission lines were selected in order to include the most interesting elements for environmental studies (Zn, Pb, Ni, Cr, V and Cu) and the concentrations ranged according with the values occurring in the real samples. In order to distinguish between chemical and physical interfering effects, the Mg 280.270–Mg 285.213 line intensity ratio was measured, in each condition. Both pneumatic and ultrasonic nebulization were considered for comparison. It was found that both the elements which constitute the sample and the reagents which are added during the sample preparation steps significantly influence the emission intensity of all the analytes, depending on the analytical concentration and the nebulization system. Generally, the signal variations were higher with ultrasonic nebulization. Concerning the interference mechanism, it was found that the effect of the major elements (Na, K, Mg, Ca, Al and Fe) is essentially related to a change of the aerosol generation and transport processes. Differently, acetic acid, ammonium acetate and hydroxylamine hydrochloride significantly improved the plasma excitation conditions, depending on their concentration. A change of the sample introduction efficiency due to the presence of these reagents was also evident. On the contrary, the effect of hydrochloric and nitric acid emerged to be related only to the processes occurring in the sample introduction system.     

Determination of trace elements in human serum by inductively coupled plasma atomic emission spectrometry with flow injection

An analytical method for the simultaneous determination of some trace elements (Au, Fe, Mg, Li, Sr, Zn) in human serum by inductively coupled plasma atomic emission spectrometry (ICP-AES) with flow injection is described. Physical interference caused by the change of sample viscosity is discussed. When 100 μl of serum was injected, the relevant recoveries of > 99% for Li, > 98% for Cu and Mg, > 95% for Fe were obtained for an NIST SRM with R.S.D. > 1.3% using optimized flow injection parameters. The prepared lyophilized control serum for routine analysis in clinical laboratories was analyzed and verified for the validity of the technique employed in this experiment using NIST SRM 909 as a primary reference material.     

Trace element determination using static high-sensitivity inductively coupled plasma optical emission spectrometry (SHIP-OES)

A low-flow air-cooled inductively coupled plasma (ICP) design for optical emission spectrometry (OES) with axial plasma viewing is described and an evaluation of its analytical capabilities in trace element determinations is presented. Main advantage is a total argon consumption of 0.6 L min⁻¹ in contrast to 15 L min⁻¹ using conventional ICP sources.The torch was evaluated in trace element determinations and studied in direct comparison with a conventional torch under the same conditions with the same OES system, ultrasonic nebulization (USN) and single-element optimization. A variety of parameters (x-y-position of the torch, rf power, external air cooling, gas flow rates and USN operation parameters) was optimized to achieve limits of detection (LOD) which are competitive to those of a conventional plasma source.Ionic to atomic line intensity ratios for magnesium were studied at different radio frequency (rf) power conditions and different sample carrier gas flows to characterize the robustness of the excitation source. A linear dynamic range of three to five orders of magnitude was determined under compromise conditions in multi-element mode. The accuracy of the system was investigated by the determination of Co, Cr, Mn, Zn in two certified reference materials (CRM): CRM 075c (Copper with added impurities), and CRM 281 (Trace elements in rye grass). With standard addition values of 2.44 ± 0.04 and 3.19 ± 0.21 μg g⁻¹ for Co and Mn in the CRM 075c and 2.32 ± 0.09, 81.8 ± 0.4, 32.2 ± 3.9 for Cr, Mn and Zn, respectively, were determined in the samples and found to be in good agreement with the reported values; recovery rates in the 98-108% range were obtained. No influence on the analysis by the matrix load in the sample was observed.     

Direct multielement trace analyses of silicon carbide powders by spark ablation simultaneous inductively coupled plasma optical emission spectrometry

A procedure for the direct analysis of silicon carbide powders (SiC) by simultaneous detection inductively coupled plasma optical emission spectrometry using a Spectro-CIROS™ spectrometer (CCD-ICP-OES) and a novel spark ablation system Spectro-SASSy (SA) as sample introduction technique is described. The sample preparation procedure for SA of non-conducting material is based on mixing the sample powders with a conducting matrix, in this case copper and briquetting pellets. Pressing time, pressure and mixing ratio are shown to be important parameters of the pelleting technique with respect to their mechanical stability for the reliability of the analysis results. A mixing ratio of 0.2 g +0.6 g for SiC and Cu, a pressure of 10 t cm^− 2 and a pressing time of 8 min have been found optimum. It has also been shown that the spark parameters selected are crucial for uniform volatilization. Electron probe micrographs of the burning spots and the analytical signal magnitude showed that a rather hard spark at 100 Hz was optimum. The determination of trace elements in silicon carbide powders is demonstrated using a calibration based on the addition of standard solutions. For Al, Ti, V, Mn and Fe detection limits in the lower µg g^− 1 range can be achieved. Internal standardization with Y in combination with the addition of standard solutions allows relative standard deviations in the range of 4 to 24% for concentration levels of the order of 3 to 350 µg g^− 1.     

电感耦合等离子体-发射光谱分析中硫酸基体效应及抑制

研究了电感耦合等离子体-发射光谱分析中的硫酸基体效应及克服干扰的有效方法。对2%~20%范围内4种不同体积分数H2SO4溶液中30种元素的基体效应进行了观察,发现H2SO4对各元素的谱线发射强度均存在明显的抑制作用。实验证实体积分数5%乙酸可有效抑制H2SO4的基体效应,并建立了H2SO4溶液中痕量元素的电感耦合等离子体-发射光谱分析法。     

微波消解-电感耦合等离子体质谱同时测定普里兹湾沉积物中微量元素

以HNO3-H2O2为消解体系,采用微波对沉积物进行消解,建立了普里兹湾沉积物中微量元素的电感耦合等离子体质谱(ICP-MS)测定方法。从样品分析数据可以看出:8个站位10种元素总量变化范围为493.41～1481.02μg/g,总量最大值是最小值的3.00倍。元素Ba、Mn在总量中占了很大比例,V次之,而As、Mo、Ag、Cd的含量很少。大部分元素检出限可达ng/L,仅Co、Mo 2种元素的检出限稍高;各元素线性良好,相关系数r2≥0.9997。方法的RSD<5.0%,适用于普里兹湾沉积物中微量元素的定量分析。     

Multiple small volume microwave-assisted digestions using conventional equipment for multielemental analysis of human breast biopsies by inductively coupled plasma optical emission spectrometry

A multiple microwave-assisted digestion procedure using small PTFE closed vials (6 mL capacity) inserted into conventional microwave digestion vessels has been developed as a fast, efficient and clean methodology for multielemental analysis of human breast biopsies by inductively coupled plasma optical emission spectrometry. This small volume strategy allows drastically diminishing the volume of acid needed for digestion, and in turn, a decrease in sample dilution and an increase in sample throughput is achieved. A 2_IV^4-1 fractional factorial design was used for screening optimization of four variables that can influence the digestion efficiency: (A) nitric acid volume, (B) pre-digestion step, (C) microwave power, and (D) digestion time. A validation study included linearity, precision, detection and quantification limits. Validation against different biological certified reference materials (CRMs) was also performed.The digestion method is suitable for the determination of Al, Ca, Cu, Fe, K, Mg, Mn, P, S and Zn in small size biological samples such as breast biopsies (<30 mg dry mass). Forty-seven biopsies from 39 women were analyzed: 20 samples from healthy women corresponding to mammoplasties and 27 samples from patients suffering from cancer pathology (19 corresponded to tumour and 8 to adjacent normal tissue). A significant accumulation of Al, Ca, Cu, K, Mg, Mn, P and Zn was found in tumour as compared to healthy tissues. When this comparison is made for tumour and adjacent tissues, a significant accumulation of Al, Mg, P and Zn in tumour tissues was observed. Finally, only Ca significantly accumulates in the adjacent tissues as compared to healthy tissues.     

电感耦合等离子体原子发射光谱法（ICP-AES）测定RoHS指令聚合物中的铅和镉

本文引入微波技术消解聚合物塑料样品,使用电感耦合等离子体原子发射光谱仪（ICP-AES）测定聚合物中的铅（Pb）和镉（Cd）含量,并建立了优化的样品消解程序和测定方法,得到满意的测定结果。[摘要应包括目的、方法、结果、结论,请修改,同时修改英文]该方法具有效率高、污染小的优点。检测结果具有良好的精密度。     

Determination of impurities in magnesium niobate by slurry introduction axially viewed inductively coupled plasma optical emission spectrometry

A simple preparation scheme is described for the quantitative analysis of a magnesium niobate sample using slurry introduction axially viewed inductively coupled plasma optical emission spectrometry. Relationships between the stability of slurries and the conditions, such as particle size, pH, dispersant and amount of dispersant, were investigated experimentally. The MgNb₂O₆ slurry sample was prepared by adding the dispersant sodium polyacrylate and agitation in an ultrasonic bath to ensure good dispersion. Under optimization of pH and amount of dispersant, an analysis of minor and trace impurities (Ba, Ca, Cr, Cu, Fe, Mn, Ni, Pb) in magnesium niobate was accomplished. Applying a paired t test, we showed that the results were in agreement at a 95% confidence level with the reference values obtained by a fusion method for a magnesium niobate sample, which verified that the calibration curves could be established by aqueous standards. Analytical results demonstrate that the factors that affected the accuracy of determination for MgNb₂O₆ are mainly the particle size of the sample and the stability of slurry.     

On-line preconcentration of some rare earth elements in water samples using C18-cartridge modified with l-(2-pyridylazo) 2-naphtol (PAN) prior to simultaneous determination by inductively coupled plasma optical emission spectrometry (ICP–OES)

The on-line column preconcentration technique with inductively coupled plasma optical emission spectroscopy (ICP–OES) has been developed using a cartridge filled with octadecyl silica modified by l-(2-pyridylazo) 2-naphtol (PAN). The aim of this method was to determine some rare earth elements (REEs) (Ce, Dy, La, Sm, and Y) and uranium in water samples. Sample solutions were passed through the C₁₈-modified column. The adsorbed cations were subsequently eluted from the column and transferred into the plasma with nitric acid solution for simultaneous determination of them. Sample pH, amount of PAN as a complexing agent, sampling and eluting flowrates and concentration of the eluent were optimized. Detection limits based on three times of standard deviations of blank by 10 replicates were in the range of 11 ng l⁻¹ for Dy to 69 ng l⁻¹ for U. Sample throughput was 10 samples h⁻¹. The proposed method was applied to determine REEs in natural water samples. Recoveries of the REEs from natural water samples were between 95 and 106% with percent relative standard deviation (%R.S.D.) of 1.0–7.9%.     

Direct determination of impurities in high purity silicon carbide by inductively coupled plasma optical emission spectrometry using slurry nebulization technique

A novel method for the determination of Al, Ca, Cr, Cu, Fe, Mg, Mn, Ni and Ti in high purity silicon carbide (SiC) using slurry introduction axial viewed inductively coupled plasma optical emission spectrometry (ICP-OES) was described. The various sizes of SiC slurry were dispersed by adding dispersant polyethylene imine (PEI). The stability of slurry was characterized by zeta potential measurement, SEM observation and signal stability testing. The optimal concentration of PEI was found to be 0.5 wt% for the SiC slurry. Analytical results of sub-μm size SiC by the slurry introduction were in good accordance with those by the alkaline fusion method which verified that determination could be calibrated by aqueous standards. For μm size SiC, results of most elements have a negative deviation and should be calibrated by the Certified Reference Material slurry. Owing to a rather low contamination in the sample preparation and stability of the slurry, the limits of detection (LODs), which are in the range of 40-2000 ng g⁻¹, superior to those of the conventional nebulization technique by ICP-OES or ICP-MS.     

A study of uniformity of elements deposition on glass fiber filters after collection of airborne particulate matter (PM-10), using a high-volume sampler

A study was conducted to evaluate the homogeneity of the distribution of metals and metalloids deposited on glass fiber filters collected using a high-volume sampler equipped with a PM-10 sampling head. The airborne particulate matter (APM)-loaded glass fiber filters (with an active surface of about 500 cm²) were weighed and then each filter was cut in five small discs of 6.5 cm of diameter. Each disk was mineralized by acid-assisted microwave (MW) digestion using a mixture of nitric, perchloric and hydrofluoric acids. Analysis was performed by axial view inductively coupled plasma optical emission spectrometry (ICP OES) and the elements considered were: Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Sb, Ti and V. The validation of the procedure was performed by the analysis of the standard reference material NIST 1648, urban particulate matter. As a way of comparing the possible variability in trace elements distribution in a particular filter, the mean concentration for each element over the five positions (discs) was calculated and each element concentration was normalized to this mean value. Scatter plots of the normalized concentrations were examined for all elements and all sub-samples. We considered that an element was homogeneously distributed if its normalized concentrations in the 45 sub-samples were within ±15% of the mean value ranging between 0.85 and 1.15. The study demonstrated that the 12 elements tested showed different distribution pattern. Aluminium, Cu and V showed the most homogeneous pattern while Cd and Ni exhibited the largest departures from the mean value in 13 out of the 45 discs analyzed. No preferential deposition was noticed in any sub-sample.     

Analytical evaluation of electrothermal vaporization/low-pressure inductively coupled plasma atomic emission spectrometry for trace elemental analysis in microliter samples

A novel method for the determination of trace elements in microliter samples using the tantalum filament electrothermal vaporization/low-pressure inductively coupled plasma (ETV/LP-ICP) atomic emission spectrometry has been developed. An improved tantalum filament ETV was directly coupled with LP-ICP system for efficient vaporization of microliter samples and further quantitative analysis. The experimental parameters including ETV current, rf power and mass flow rate of argon carrier gas were optimized using the copper emission signal produced by 5 μl of standard solution (5 μg/ml). Under the optimized condition, the analytical performances including linearity, precision and detection limit for the developed system were investigated. Absolute detection limits in the range of 22–391 pg for selected eight elements (Fe, Cu, Cr, Mn, Pb, K, Zn and Mg) were obtained with satisfactory precision (<8.9% RSD). The feasibility of the developed system has been demonstrated by analyzing wheat gluten NIST standard sample.