Multi-class pesticide analysis in human hair by gas chromatography tandem (triple quadrupole) mass spectrometry with solid phase microextraction and liquid injection

A method for the simultaneous detection and quantification of 22 pesticides from different chemical classes was developed using solid-phase microextraction (SPME) and gas chromatography tandem (triple quadrupole) mass spectrometry. Pesticides were extracted from 50 mg of pulverized hair with acetonitrile. The extract was submitted to two successive steps of direct immersion-SPME at 30 °C and 90 °C or to a liquid injection without SPME in order to obtain optimized conditions for each of the 22 analytes investigated. Validation parameters were significantly influenced by both the injection mode (SPME vs liquid injection) and the temperature of SPME. Limits of quantification ranged from 0.05 pg mg⁻¹ for trifluralin to 10 pg mg⁻¹ for pentachlorophenol. The application of the validated method to the analysis of samples collected from non-occupationally exposed volunteers demonstrated the presence of pesticides in all the samples tested. Altogether, 13 different analytes were detected at concentration above the limit of quantification.     

Determination of pesticides in water samples by solid phase extraction and gas chromatography tandem mass spectrometry

A multiresidue method for the determination of more than 80 pesticides in water has been developed and validated. The proposed method is based on SPE followed by GC coupled to MS/MS. Different variables affecting SPE procedure, such as cartridges, sample volume and solvents were studied, and mass spectrometric conditions were optimised in order to increase selectivity and sensitivity. Calibration curves were linear over the range of 0.03-0.5 microg/L. Recoveries were in the range of 70-110% and repeatability was below 20% for the lowest calibration point. LODs ranged from 0.001 to 0.025 microg/L and LOQs from 0.003 to 0.076 microg/L. Finally, the method was successfully applied to the analysis of water samples from southeast of Spain.     

Comparison of hollow fiber liquid phase microextraction and dispersive liquid-liquid microextraction for the determination of organosulfur pesticides in environmental and beverage samples by gas chromatography with flame photometric detection

Two methods based on hollow fiber liquid phase microextraction (HF-LPME) and dispersive liquid-liquid microextraction (DLLME), have been critically compared for the analysis of organosulfur pesticides (OSPs) in environmental and beverage samples by gas chromatography-flame photometric detection (GC-FPD). Experimental conditions including extraction solvent, solvent volume, extraction time, temperature and ionic strength have been investigated for both HF-LPME and DLLME. Under the optimal conditions, the limits of detection for the six target OSPs (malathion, chlorpyrifos, buprofezin, triazophos, carbosulfan and pyridaben) obtained by HF-LPME-GC-FPD and DLLME-GC-FPD were ranged from 1.16 microg/L to 48.48 microg/L and 0.21 microg/L to 3.05 microg/L, respectively. The relative standard deviations (RSDs, n=5) were in the range of 3.4-8.0% and 8.5-13.7%with the enrichment factors (EFs) of 27-530 and 176-946 folds for HF-LPME-GC-FPD and DLLME-GC-FPD, respectively. Both methods were found to be simple, fast, efficient, and inexpensive. Compared with HF-LPME, the advantages of DLLME technique were less extraction time, suitable for batches of samples pretreatment simultaneously, a higher extraction capacity when analyzing simple samples such as water samples. While for the analysis of complicated matrix samples such as soil and beverage samples, HF-LPME was demonstrated to be more robust and more suitable. Both methods were applied to the analysis of six OSPs in different waters, soil and beverage samples, and no target OSPs was found in these samples. For analysis of the spiked samples, the recovery of 81.7-114.4% with RSDs of 0.6-9.6% were obtained for HF-LPME, and the recovery of 78.5-117.2% with RSDs of 0.6-11.9% were obtained for DLLME.     

Comparison of ultra-performance liquid chromatography and high-performance liquid chromatography for the determination of priority pesticides in baby foods by tandem quadrupole mass spectrometry

Determination of 16 priority pesticides and transformation products specified in the EU Baby Food Directive 2003/13/EC has been compared using high-performance liquid chromatography (HPLC) and ultra-performance liquid chromatography (UPLC) coupled to tandem quadrupole mass spectrometry (MS/MS). Prior to analysis, co-extractives were removed from acetonitrile extracts using dispersive solid-phase extraction (SPE) with primary secondary amine (50 mg). Extracts spiked with pesticides at 1 microg kg(-1) yielded average recoveries in the range 85-119%, with relative standard deviations less than 17%. The HPLC-MS/MS and UPLC-MS/MS multi-residue methods developed are simple, rapid and suitable for the quantification and confirmation of the 16 priority pesticides in fruit-, potato- and cereal-based baby food at 1 microg kg(-1). The major advantages of UPLC, using 1.7 microm particles, over HPLC are the speed of analysis, the narrower peaks (giving increased signal-to-noise ratio) and improved confirmation for the targeted pesticides in the analyses of baby foods.     

Multiresidue analysis of pesticides in animal liver by gas chromatography using triple quadrupole tandem mass spectrometry

Two methods for extracting organochlorine (OCs) and organophosphorus (OPs) pesticides from animal liver have been developed. The determination was carried out by gas chromatography with electron impact ionization tandem mass spectrometry (GC-(EI-)MS/MS) using a triple quadrupole (QqQ) analyzer. First, a liquid-solid extraction performed with a high-speed homogenizer (Polytron) using ethyl acetate as solvent, and a subsequent clean-up by gel permeation chromatography (GPC) was applied, determining 34 pesticides. Secondly, a matrix solid phase dispersion (MSPD) extraction with octadecylsilyl (C(18)) sorbent combined with a Florisil clean-up and ethyl acetate elution was performed, analyzing 25 compounds. These methodologies have been tested and compared in the sample pre-treatment due to the fatty nature of the matrix. The GPC method was finally selected and validated, yielding recoveries in the range 70-115%, with precision values expressed as relative standard deviation (RSD) lower or equal to 20%, at the spiking levels of 25 and 50 microg kg(-1), and limits of quantification (LOQs) lower than the maximum residue levels (MRLs) set by the European Union in animal products, except for isofenphos. Linearity was also studied ranging between 5 and 300 microg kg(-1) for most of pesticides. This method was applied to the analysis of real liver samples of chicken, pork and lamb.     

Multi-residue determination of 130 multiclass pesticides in fruits and vegetables by gas chromatography coupled to triple quadrupole tandem mass spectrometry

A multi-residue method has been developed and validated for the simultaneous quantification and confirmation of around 130 multiclass pesticides in orange, nectarine and spinach samples by GC-MS/MS with a triple quadrupole analyzer. Compounds have been selected from different chemical families including insecticides, herbicides, fungicides and acaricides. Three isotopically labeled standards have been used as surrogates in order to improve accurate quantitation. Samples were extracted by using accelerated solvent extraction (ASE) with ethyl acetate. In the case of spinach, an additional clean-up step by gel permeation chromatography was applied. Determination was performed by GC-MS/MS in electron ionization mode acquiring two MS/MS transitions for each analyte. The intensity ratio between quantitation transition (Q) and identification transition (q) was used as confirmatory parameter (Q/q ratio). Accuracy and precision were evaluated by means of recovery experiments in orange, nectarine, and spinach samples spiked at two concentration levels (0.01 and 0.05 mg/kg). Recoveries were, in most cases, between 70% and 120% and RSD were below 20%. The limits of quantification objective for which the method was satisfactorily validated in the three samples matrices were for most pesticides 0.01 mg/kg. Matrix effects over the GC-MS/MS determination were tested by comparison of reference standards in pure solvent with matrix-matched standards of each matrix. Data obtained showed enhancement of signal for the majority of analytes in the three matrices investigated. Consequently, in order to reduce the systematic error due to this effect, quantification was performed using matrix-matched standard calibration curves. The matrix effect study was extended to other food matrices such as raisin, paprika, cabbage, pear, rice, legume, and gherkin, showing in all cases a similar signal enhancement effect.     

Simultaneous enantioselective determination of six pesticides in aqueous environmental samples by chiral liquid chromatography with tandem mass spectrometry

A robust and sensitive method was developed for the enantiomeric analysis of six chiral pesticides (including metalaxyl, epoxiconazole, myclobutanil, hexaconazole, napropamide, and isocarbophos) in aquatic environmental samples. The optimized chromatographic conditions for the quantification of all the 12 enantiomers were performed with Chiralcel OD‐RH column using mobile phase consisting of 0.1% aqueous formic acid and acetonitrile operated under reversed‐phase conditions and then analyzed using liquid chromatography with tandem mass spectrometry. Twelve enantiomers were detected in multiple reaction monitoring mode. Solid‐phase extraction and dispersive liquid–liquid microextraction were employed in this study. Response surface methodology was applied to assist in the dispersive liquid–liquid microextraction optimization. Under the optimum conditions, recoveries of pesticides enantiomers varied from 83.0 to 103.2% at two spiked levels with relative standard deviation less than 11.5%. The concentration factors were up to 1000 times. Method detection and quantification limits varied from 0.11 to 0.48 ng/L and from 0.46 to 1.49 ng/L, respectively. Finally, this method was used to determination of the enantiomers composition of the six pesticides in environmental aqueous matrices, which will help better understand the behavior of individual enantiomer and make accurate risk assessment to ecosystems.     

Headspace solid-phase microextraction gas chromatography tandem mass spectrometry for the determination of brominated flame retardants in environmental solid samples

A headspace solid-phase microextraction gas chromatography coupled with tandem mass spectrometry (HSSPME-GC-MS-MS) methodology for determination of brominated flame retardants in sediment and soil samples is presented. To the best of our knowledge, this is the first time that SPME has been applied to analyze polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in environmental solid samples. Analyses were performed using 0.5-g solid samples moisturized with 2 mL water, employing a polydimethylsiloxane (PDMS) fiber coating, exposed to the headspace at 100 °C for 60 min. Several types of environmental solid samples were included in this study and the extraction efficiency was related to the organic matter content of the sample. Calibration was performed using real samples, and the method showed good linearity over a wide concentration range, precision, and afforded quantitative recoveries. The obtained detection limits were in the sub-ng g⁻¹ for all the target analytes in both samples. The proposed procedure was applied to several marine and river sediments and soils, some of which were found to contain PBDEs at concentrations in the ng g⁻¹ level; BDE-47, BDE-100, and BDE-99 were the major congeners detected. The proposed method constitutes a rapid and low-cost alternative for the analysis of the target brominated flame retardants in environmental solid samples, since the clean-up steps, fractionation, and preconcentration of extracts inherent to the classical multi-step solvent extraction procedures are avoided.      

Combined use of liquid chromatography triple quadrupole mass spectrometry and liquid chromatography quadrupole time-of-flight mass spectrometry in systematic screening of pesticides and other contaminants in water samples

As a suitable way for routine screening of pesticides and control of other organic contaminants in water, the combination of liquid chromatography triple quadrupole tandem mass spectrometry (LC–QqQ-MS/MS) and liquid chromatography–hybrid quadrupole time-of-flight mass spectrometry (LC–QTOF-MS) has been applied to the analysis of 63 surface and waste water samples after conventional solid-phase extraction (SPE). The extracts were screened for 43 pesticides or degradation products by LC–QqQ-MS/MS achieving limits of detection (LOD) ranged from 0.04 to 2 ng L⁻¹. Of the 43 selected pesticides, 33 were detected in water samples. The ESI–QTOF MS instrument was run using two simultaneous acquisition functions with low and high collision energy (MS^E approach) and acquiring the full mass spectra. A home-made database containing more than 1100 organic pollutants was used for substance identification. Around 250 of these compounds were available at the laboratory as reference standards. Five pesticides and 3 of their degradation products, different to those selected in the QqQ method, were detected by QqTOF-MS. Thirteen pharmaceuticals and two drugs of abuse were also identified in the samples. In practice, the sample preparation proved to be suitable for both techniques and for a wide variety of substances with different polarity. Mutual confirmation and evidence of co-occurrence of several other organic contaminants were the main advantages of the combination of both techniques.     

Solid-phase microextraction combined with gas chromatography/triple quadrupole tandem mass spectrometry for determination of nitrated polycyclic aromatic hydrocarbons in sediments

Nitro-polycyclic aromatic hydrocarbons have been detected in various environmental media. However, determination in sediment matrix is challenging due to the lack of a suitable method. In this study, a reliable method for determining 15 nitro-polycyclic aromatic hydrocarbons in sediments was developed based on accelerated solvent extraction and solid-phase microextraction coupled with gas chromatography–tandem mass spectrometry. The accelerated solvent extraction and solid-phase microextraction are sample pre-treatment techniques that have advantages, such as rapid operation and minimal sample volume. Initially, the solid-phase microextraction was optimized using five commercial fibers and from that 65 μm polydimethylsiloxane/divinylbenzene fiber was selected as the best fiber. Further, the accelerated solvent extraction conditions were optimized by Taguchi experimental design, such as extraction temperature (120℃), extraction solvent (dichloromethane), number of cycles (two), static extraction period (4 min), and rinse volume (90%). The method parameters, such as limits of quantitation, and intraday and interday accuracy and precision, were in the range of 0.067–1.57 ng/g, 75.2–115.2%, 69.9–115.4%, and 1.0–16.5%, respectively. Upon meeting all the quality criteria, the method was applied successfully to analyze real sediment samples. Therefore, our study creates a new prospect for the future application of direct immersion solid-phase microextraction in sediment analysis.     

Automated polyvinylidene difluoride hollow fiber liquid-phase microextraction of flunitrazepam in plasma and urine samples for gas chromatography/tandem mass spectrometry

A new polyvinylidene difluoride (PVDF) hollow fiber (200 μm wall thickness, 1.2 mm internal diameter, 0.2 μm pore size) was compared with two other polypropylene (PP) hollow fibers (200, 300 μm wall thickness, 1.2 mm internal diameter, 0.2 μm pore size) in the automated hollow fiber liquid-phase microextraction (HF-LPME) of flunitrazepam (FLNZ) in biological samples. With higher porosity and better solvent compatibility, the PVDF hollow fiber showed advantages with faster extraction efficiency and operational accuracy. Parameters of the CTC autosampler program for HF-LPME in plasma and urine samples were carefully investigated to ensure accuracy and reproducibility. Several parameters influencing the efficiency of HF-LPME of FLNZ in plasma and urine samples were optimized, including type of porous hollow fiber, organic solvent, agitation rate, extraction time, salt concentration, organic modifier, and pH. Under optimal conditions, extraction recoveries of FLNZ in plasma and urine samples were 6.5% and 83.5%, respectively, corresponding to the enrichment factor of 13 in plasma matrix and 167 in urine matrix. Excellent sample clean-up was observed and good linearities (r² = 0.9979 for plasma sample and 0.9995 for urine sample) were obtained in the range of 0.1–1000 ng/mL (plasma sample) and 0.01–1000 ng/mL (urine sample). The limits of detection (S/N = 3) were 0.025 ng/mL in plasma matrix and 0.001 ng/mL in urine matrix by gas chromatography/mass spectrometry/mass spectrometry.     

Isolation, preconcentration and determination of rhamnolipids in aqueous samples by dispersive liquid-liquid microextraction and liquid chromatography with tandem mass spectrometry

An analytical method based on liquid chromatography-tandem mass spectrometry (LC-MS-MS) was developed for the determination of rhamnolipids. A dispersive liquid-liquid microextraction (DLLME) procedure was used to isolate and concentrate target compounds from aqueous samples collected from surface water, sewage treatment plant effluent and cultivation of microbial culture. Development of the DLLME procedure included optimization of several important parameters such as kind and volume of extracting and dispersing solvents as well as sample pH. Under optimized conditions a two-step extraction with sonication was used. Chloroform was applied as the extracting and acetone as the dispersing solvent. The recoveries of the analytes were 70-87%. Matrix effects investigated for the analytes revealed existence of ionization enhancement for both mono- and dirhamnolipids.     

Determination of pesticides in aqueous samples by solid-phase microextraction in-line coupled to gas chromatography—mass spectrometry

A multiresidue method was developed for the determination of nitrogen- and phosphorous-containing pesticides (amines, anilides, phosphorothioates, and triazines) by solid-phase microextraction (SPME) in-line coupled to gas chromatography—mass spectrometry (GC/MS). The 85-µm polyacrylate fiber was first dipped into the aqueous sample for a given time and then directly introduced into the heated injector of the gas chromatography—mass spectrometer, where the analytes are thermally desorbed. The method was evaluated with respect to the limit of detection, linearity, and precision. The limit of detection [selected ion monitoring (SIM) mode] depends on the compound and varies from 5 to 90 ng/L. The method is linear over at least 3 orders of magnitude with coefficients of correlation usually ≥0.996. In general, the coefficient of variation (precision) is <10%. The partitioning of the analyte between the aqueous phase and the polymeric phase depends on the hydrophobicity of the compound as expressed by the octanol—water partitioning coefficient P _ow. The addition of sodium chloride has a strong effect on the extraction efficiency. This effect increases with decreasing hydrophobicity (increasing polarity) of the compound. The triazines atrazine, simazine, and terbuthylazine were first identified and quantified in water samples from the effluent of sewage plants by SPME-gas chromatography—nitrogen—phosphorus detection (GC/NPD). For such a complex matrix GC/NPD is not sufficiently selective for an unambiguous identification at low levels (<1 ppb) of pesticides. Selectivity may be enhanced by using SMPE-GC/MS in the SIM mode with three characteristic ions for each pesticide. This method allows an unequivocal identification and quantification at low levels of pesticides in environmental samples. At a target limit of detection below 100 ng/L, SPME-GC/MS represents a very simple, fast, selective, and solvent-free multimethod for the extraction and determination of these nitrogen- and phosphorous-containing pesticides from aqueous samples.     

Determination of priority pesticides in baby foods by gas chromatography tandem quadrupole mass spectrometry

A gas chromatography-tandem quadrupole mass spectrometry (GC-MS/MS) method for the determination of twelve priority pesticides, and transformation products (e.g. metabolites) specified in the EU Baby Food Directive 2003/13/EC is described. Prior to GC-MS/MS analysis, co-extractives were removed from acetonitrile extracts using dispersive solid phase extraction with octadecyl (200 mg) and primary secondary amine (50 mg) sorbents. The clean up proved essential for the satisfactory long-term chromatographic performance during the analysis of a range of representative commercially pre-prepared baby food samples. Extracts spiked with pesticides at 1-8 microg kg(-1), yielded average recoveries in the range 60-113% with relative standard deviations less than 28%.     

Simultaneous determination of toxins in algae and water samples by high-performance liquid chromatography with triple quadrupole mass spectrometry

A facile method based on liquid chromatography coupled with electrospray ionization tandem triple quadrupole mass spectrometry working in selected reaction monitoring mode has been established to analyze toxins in the algae and water samples. Twelve types of toxins (anatoxin, cylindrospermopsin, dinophysistoxin-1, nodularin, okadaic acid, microcystins) were efficiently separated under optimized liquid chromatography coupled with mass spectrometry conditions in the selected reaction monitoring mode. Correlation coefficients of the calibration curves, all felt in the range of 0.9958-0.9998, indicated good linearity. The detection limits of toxins in this method were all lower than 0.20 ng/mL and the quantification limits were in the range from 0.04 to 0.60 ng/mL. Except for anatoxin, cylindrospermopsin, and nodularin, the other toxins' recoveries varied from 55.45 to 140.85%. And the relative standard deviations of interday and intraday precision were at 8.61% (n = 5). The high-performance liquid chromatography (HPLC)/electrospray ionization (ESI)-mass spectrometery (MS) method was also successfully applied to analyze the algae and water samples. Owing to its exclusive selectivity and excellent sensitivity, the developed method is a tool for comprehensive analyses of the 12 types of toxins at nanogram levels.     

Separation and determination of seleno amino acids using gas chromatography hyphenated with inductively coupled plasma mass spectrometry after hollow fiber liquid phase microextraction

A new derivatization–extraction method for preconcentration of seleno amino acids using hollow fiber liquid phase microextraction (HF‐LPME) was developed for the separation and determination of seleno amino acids in biological samples by gas chromatography–inductively coupled plasma mass spectrometry (GC–ICP‐MS). Derivatization was performed with ethyl chloroformate (ECF) to improve the volatility of seleno amino acids. Parameters influencing microextraction, including extraction solvent, pH of sample solution, extraction time, stirring speed, and inorganic salt concentration have been investigated. Under the optimal conditions, the limits of detection (LODs) obtained for Se‐methyl‐selenocysteine (SeMeCys), selenomethionine (SeMet), and selenoethionine (SeEth) were 23, 15, and 11 ng Se l⁻¹, respectively. The relative standard deviations (RSDs) were 14.6%, 16.4%, and 19.4% for SeMeCys, SeMet, and SeEth (c = 1.0 ng ml⁻¹, n = 7), respectively, and the RSDs for SeMeCys, SeMet could be improved obviously if SeEth was utilized as the internal standard. The proposed method was applied for the determination of seleno amino acids in extracts of garlic, cabbage, and mushroom samples, and the recoveries for the spiked samples were in the range of 96.8–108% and 93.4–115% with and without the use of SeEth as internal standard. The developed method was also applied to the analysis of SeMet in a certified reference material of SELM‐1 yeast and the determined value is in good agreement with the certified value. Copyright © 2008 John Wiley & Sons, Ltd.     

Solid-phase extraction followed by liquid chromatography quadrupole time-of-flight tandem mass spectrometry for the selective determination of fungicides in wine samples

In this work, a reliable and selective procedure for the determination of thirteen fungicides in red and white wine samples is proposed. Solid-phase extraction (SPE) and liquid chromatography (LC) tandem mass spectrometry (MS/MS), based on a hybrid quadrupole time-of-flight (QTOF) system, were used as sample preparation and determination techniques, respectively. Extraction and purification of target analytes was carried out simultaneously by using a reversed-phase Oasis HLB (200mg) SPE cartridge combined with acetonitrile as elution solvent. Fungicides were determined operating the electrospray source in the positive ionization mode, with MS/MS conditions adjusted to obtain at least two intense product ions per compound, or registering two transitions per species when a single product was noticed. High selective MS/MS chromatograms were extracted using a mass window of 20 ppms for each product ion. Considering external calibration as quantification technique, the overall recoveries (accuracy) of the procedure ranged between 81% and 114% for red and white wine samples (10-20 mL), spiked at different concentrations between 5 and 100 ng mL(-1). Relative standard deviations of the above data stayed below 12% and the limits of quantification (LOQs) of the method, calculated for 10 mL of wine, varied between 0.1 ng mL(-1) for cyprodinil (CYP) and 0.7 ng mL(-1) for myclobutanil (MYC). The optimized method was applied to seventeen commercial wines produced in Spain and obtained from local supermarkets. Nine fungicides were determined, at levels above the LOQs of the method, in the above samples. The maximum concentrations and the highest occurrence frequencies corresponded to metalaxyl (MET) and iprovalicarb (IPR).     

Determination of polychlorodibenzo-p-dioxins and polychlorodibenzofurans by gas chromatography/tandem mass spectrometry and gas chromatography/triple mass spectrometry in a quadrupole ion trap

The determination of tetra- to octachlorodibenzo-p-dioxins and tetra- to octachlorodibenzofurans (PCCD/Fs) by high-resolution gas chromatography/tandem mass spectrometry (HRGC/MS/MS) and high-resolution gas chromatography/triple mass spectrometry (HRGC/MS(3)) in a quadrupole ion trap, equipped with an external ion source, is presented. MS/MS involves a typical four-step process, namely ionization, parent ion isolation, collision-induced dissociation (CID) and mass analysis of the daughter ions. For the MS(3) experiment, the MS/MS scan function is used with the addition of selected daughter ion isolation, their CID and the mass analysis of second-generation product ions called 'grand-daughter ions.' For both methods, the energies necessary for the CID of the 17 PCDD/Fs were determined and optimized using multiple scan functions with different CID amplitudes. The CID efficiency, defined as the signal ratio of fragment ions detected from the major dissociation channels to molecular ions isolated, was 1.15-2.40 V for parent ion dissociation (MS/MS) and 1.05-1.50 V for daughter ion dissociation (MS(3)) and for all the chloro congeners. The same sensitivity (1 pg microl(-1)) can be reached with both the MS/MS and MS(3) methods and linear responses were obtained between 1 and 100 pg microl(-1) injected.     

Single solid phase extraction method for the simultaneous analysis of polar and non-polar pesticides in urine samples by gas chromatography and ultra high pressure liquid chromatography coupled to tandem mass spectrometry

A new multiresidue method has been developed and validated for the simultaneous extraction of more than two hundred pesticides, including non-polar and polar pesticides (carbamates, organochlorine, organophosphorous, pyrethroids, herbicides and insecticides) in urine at trace levels by gas and ultra high pressure liquid chromatography coupled to ion trap and triple quadrupole mass spectrometry, respectively (GC-IT-MS/MS, UHPLC-QqQ-MS/MS). Non-polar and polar pesticides were simultaneously extracted from urine samples by a simple and fast solid phase extraction (SPE) procedure using C₁₈ cartridges as sorbent, and dichloromethane as elution solvent. Recovery was in the range of 60-120%. Precision values expressed as relative standard deviation (RSD) were lower than 25%. Identification and confirmation of the compounds were performed by the use of retention time windows, comparison of spectra (GC-amenable compounds) or the estimation of the ion ratio (LC-amenable compounds). For GC-amenable pesticides, limits of detection (LODs) ranged from 0.001 to 0.436 μg L⁻¹ and limits of quantification (LOQs) from 0.003 to 1.452 μg L⁻¹. For LC-amenable pesticides, LODs ranged from 0.003 to 1.048 μg L⁻¹ and LOQs ranged from 0.011 to 3.494 μg L⁻¹. Finally, the optimized method was applied to the analysis of fourteen real samples of infants from agricultural population. Some pesticides such as methoxyfenozide, tebufenozide, piperonyl butoxide and propoxur were found at concentrations ranged from 1.61 to 24.4 μg L⁻¹, whereas methiocarb sulfoxide was detected at trace levels in two samples.