非定常空化流动涡旋运动及其流体动力特性

采用大涡模拟方法对绕水翼云状空化的水动力特性和非定常流场结构进行研究. 基于实验结果对数值方法进行验证,分析空化与流场内部涡旋结构之间的相互作用以及对水翼动力特性的影响. 研究结果表明:大涡模拟方法可以准确模拟绕水翼流动的非定常过程. 在无空化条件下,升阻力系数存在斯特劳哈数St = 0.85 的主频波动,这是由水翼尾部涡旋结构的发展脱落引起的;在云状空化条件下,升阻力系数存在St = 0.34 的高能量密度低频波动,这是由大规模云状空泡团的发展和脱落引起的;云状空化阶段的升阻力系数在St = 0.5~1.5 的范围内都存在较高的波动,这是由于空化现象对水翼尾缘涡旋结构的发展和脱落产生影响,在不同发展阶段,空化现象不同程度地降低尾缘涡旋结构脱落频率.      

摆动水翼绕流的数值研究

鱼类经常采用垂直流向的摆动进行游动, 这种摆动可以用行进波来表示. 应用浸入边界方法模拟了低雷诺数条件下水翼NACA65-010在水中摆动时的流场,并研究了雷诺数对水生动物推进效率的影响. 结果表明:随着雷诺数的增大,推力系数和推进效率增大,而功率系数减小;在Re<20时,推力系数,推进效率和功率系数的变化尤为剧烈. 随雷诺数增加,由于水翼摆动诱导的流场变化也更加复杂,水翼后缘处的涡量场强度逐渐增强. 摆动诱导反卡门涡街产生推力.      

基于GIS与确定性系数分析方法的汶川地震滑坡易发性评价

鱼类经常采用垂直流向的摆动进行游动, 这种摆动可以用行进波来表示. 应用浸入边界方法模拟了低雷诺数条件下水翼NACA65-010在水中摆动时的流场,并研究了雷诺数对水生动物推进效率的影响. 结果表明：随着雷诺数的增大,推力系数和推进效率增大,而功率系数减小;在Re<20时,推力系数,推进效率和功率系数的变化尤为剧烈. 随雷诺数增加,由于水翼摆动诱导的流场变化也更加复杂,水翼后缘处的涡量场强度逐渐增强. 摆动诱导反卡门涡街产生推力.     

电磁极宽度对圆柱绕流场影响的数值分析

在雷诺数Re=200的情况,利用Maxwell方程直接数值计算表面包覆电极与磁极圆柱体产生的电磁力分布,将其加入到动量方程中,在各种电磁力作用参数和电磁极宽度的组合下,对表面覆盖电磁极圆柱体在弱电解质中的绕流场结构及其升阻力特性进行了数值模拟与分析.结果表明,当电磁极宽度较小时,圆柱体绕流场的分离点越容易接近后驻点,而电磁力对总阻力的影响并不明显,但对压差和摩擦阻力均有明显影响.当电磁极宽度较大时,圆柱体尾部区域越容易产生射流现象,而且总阻力随电磁力作用参数和电磁极宽度增大而减小.在电磁力尚不足以完全抑制周期性涡脱落的情况下,升力幅值随电磁力作用参数增大而减小,但随电磁极宽度则先减小后略有增加,升力脉动频率则均随电磁力作用参数和电磁极宽度增大而增加.研究表明,电磁力可以有效地改善圆柱体绕流场结构,达到减小圆柱体阻力并抑制其脉动升力之目的,因此是圆柱型结构的一种有效流动控制手段.     

初始驱动角对半主动拍动翼能量获取的影响

运用浸入边界法研究初始驱动角θ0对半主动拍动翼能量获取性能的影响。半主动拍动翼的运动包括外部力主动驱动的正弦式摆动θ(t)和流体动力被动驱动的垂直运动h(t)。以雷诺数Re=1000下的二维NACA0015翼型为研究对象,数值计算了摆动角振幅θmax=75°和摆动衰减频率f*=0.16下初始驱动角对半主动拍动翼能量获取性能的影响。首先将初始驱动角θ0=0°时不同网格划分下的升力系数演化与已有文献结果进行了对比,得到二者结果相吻合,验证了数值算法的有效性。然后研究了不同的初始驱动角θ0对能量获取性能的影响,研究发现:θ0≤30°时的升力值远小于θ0≥45°的值,θ0≤30°时拍动翼向下运动,而θ0≥45°时升力值快速增大,拍动翼向下做微小运动后快速反弹向上运动;还发现相对于θ0=0°时的能量获取效率为31.22%,在θ075°范围内增大初始驱动角无益于提高能量获取效率,但是在θ0=75°时得到的能量获取效率高达39.21%;同时结果还显示θ0=60°时对净功率的输出最有利。     

鲤鱼尾鳍实时三维姿态测量及运动特性分析

为了实现鱼鳍三维运动特性的精确测量, 研究尾鳍的动态瞬时特性, 定量分析其连续变化过程, 建立了基于栅线投影和高速摄像的测量系统和与之对应的分析方法. 以自主游动的鲤鱼为实验对象, 将一组正弦光栅投射在其尾鳍表面, 产生包含三维信息的光栅条纹并由高速摄像机实时采集尾鳍摆动过程的序列图像; 对其中的每一帧图像作二维傅里叶变换、频谱滤波、逆傅里叶变换及三维位相展开等处理后, 重建尾鳍的瞬时三维形态, 再现尾鳍的连续运动过程; 据此测量结果分析研究尾鳍的运动特征及运动学参数. 结果表明, 鲤鱼游速为0.5L/s时, 尾鳍的摆动频率为1.42Hz; 鲤鱼巡游过程中尾鳍的主要运动为侧向摆动, 尾鳍的形状周期性地循环外展和内收, 且尾鳍上叶叶尖的平均摆幅比尾鳍下叶叶尖的平均摆幅约大15.6%.      

绕栅中水翼空化流动的数值和实验研究

采用数值计算和实验研究的方法研究了绕水翼和栅中水翼的非定常空化流动. 实验采用高速录像技术分别观察了绕水翼和栅中水翼云状空化形态随时间的变化, 测量了升阻力, 并对测量数据进行了频率分析. 计算时空化模型选用了能比较准确描述旋涡空化非定常特性的Kubota模型, 湍流模型采用能准确捕捉流场非定常特性的FBM模型. 计算模型的可靠性用实验结果进行验证. 结果表明, 计算与实验的结果基本一致, 相比绕单个水翼的空化流动, 绕栅中水翼的空穴厚度比较薄, 翼型近壁处的逆压梯度较小, 反向射流的速度较小, 且水汽混合区速度梯度较小, 空穴的脱落周期变长, 平均升阻力系数较小      

多段翼型缝翼流动速度的定常和非定常特性研究

用热线风速仪研究多段翼型前缘缝翼在不同条件下流动速度的定常性和非定常性。结合多段翼型定常流动Navier-Stokes方程数值模拟的结果,分析了迎角、后缘襟翼参数(偏角、缝道宽度、搭接量)对缝翼定常和非定常流动速度的影响规律。研究结果表明:在缝翼后缘处,流动分为缝道加速流动区、缝翼尾流区、缝翼上表面以上的主流区;缝翼尾流区流动速度非定常性主要表现在中低频率范围(2k Hz以下),而缝道加速流动区和缝翼上表面以上的主流区流动非定常性常表现出高频特性(2k Hz以上);在失速前随迎角增加,或者当襟翼偏角从20°向30°增加时,缝道流动加速,槽区涡减小;缝翼槽区涡形成和振荡是中低频率范围流动非定常性的机理,而缝翼鼻尖脱落涡是缝翼槽区涡振荡的激励因素。     

流向振荡圆柱绕流的格子Boltzmann方法模拟

用一种新近发展起来的格子Boltzmann方法(LBM)在相对较小的雷诺数(Re \le 200)条件下模拟了不可压缩的流向振荡圆柱绕流问题, 考查了涡脱落模态和升阻力特性. 通过模拟, 在近尾流区发现了实验研究中已经发现的对称/反对称的涡脱落模态, 包括有些传统数值方法未发现的模态. 研究了频率锁定区域的范围及其与振幅的关系, 发现振幅越大, 发生锁定的频率区域越宽. 此外还对升阻力进行了定量意义的模拟,研究了振荡频率和振幅与升阻力的关系.      

圆柱附加旋转整流罩表面压力分布及气动力特性

对圆柱附加固定整流罩的已有研究表明,它在降低升阻力和抑制涡激振动方面有优良的效果。但固定整流罩具有方向敏感性,当来流方向改变后效果会受到显著影响,甚至起到增加升阻力和加剧涡激振动的反作用。本文给圆柱附加了圆弧直径为40mm,形状夹角α分别为30°、45°、60°、75°和90°五种尺寸的旋转整流罩,并进行了风洞实验。其中整流罩可以自由地围绕圆柱轴线旋转。实验结果表明:旋转整流罩在流体力产生的力矩作用下,旋转至一个偏离尾流中心线固定角度的动态平衡位置,而平衡位置偏转角δ随着形状夹角α的增大而增大。附加旋转整流罩后,相对单圆柱能够提高尾迹区域压力,并能使时均阻力和脉动升力分别在α=30°和α=75°时获得最大43.5%和67.0%的降低。此外,对于小α(α≤60°)情况,漩涡脱落频率明显高于单圆柱情况,而对于大α(α≥75°)情况,则与单圆柱情况相接近。所有旋转整流罩升力主频的幅值较之单圆柱有了很大程度的降低,可见旋转整流罩在抑制漩涡脱落方面有很好的效果。     

基于涡量矩理论的绕振荡水翼涡动力学分析

文章采用标准k-ω SST湍流模型和动网格技术, 实现了绕俯仰振荡NACA66水翼非定常流动结构与水动力特性的数值模拟, 并基于有限域涡量矩理论定量表征了局部旋涡结构对水翼动力特性的影响. 研究结果表明: 在水翼升程阶段, 当攻角较小时, 层流向湍流的转捩点由水翼尾缘向前缘移动; 在较大攻角时, 顺时针尾缘涡?TEV在水翼吸力面上生成并向前缘发展, 同时与吸力面上的顺时针前缘涡?LEV融合发展为附着在整个吸力面上的新前缘涡?LEV, 新的?LEV与逆时针尾缘涡+TEV相互作用直至完全脱落, 直接导致了水翼的动力失速, 在回程阶段, 绕振荡水翼的流场结构逐渐由湍流转变为层流. 基于有限域涡量矩理论的定量分析发现, 有限域内附着的?LEV和?TEV提供正升力, 当?LEV发展覆盖整个吸力面时对升力的贡献最大, 占总升力近50%, 而+TEV提供负升力. 同时发现, 有限域内各旋涡内部的不同区域提供的升力有正有负; 而逸出有限域的旋涡内部不同区域提供的升力方向均保持一致, 其中顺时针涡提供正升力, 而逆时针涡提供负升力. 在失速阶段, 域外旋涡整体对升力贡献较小且存在小幅波动, 体现了流动的非定常性.      

Influences of Lorentz force on the hydrofoil lift

In this paper, Lorentz forces are proved to be able to suppress separation in flows over hydrofoils. Furthermore, a differential equation of pressure distributions on the hydrofoil surface is derived, from which it is found that BVF （boundary vortex flux） σ is a suitable criterion for describing the lift coefficient variations during the electromagnetic control process. According to our numerical results, the periodic variations of lift for a hydrofoil at an attack angle of 17 ° are analyzed and its inherent mechanism is discussed in detail with the concept of BVE On the other hand, the effects of Lorentz force on the hydrofoil＇s lift are investigated both experimentally and numerically for different magnitudes and locations.     

Effects of unsteady deformation of flapping wing on its aerodynamic forces

Effects of unsteady deformation of a flapping model insect wing on its aerodynamic force production are studied by solving the Navier-Stokes equations on a dynamically deforming grid.Aerodynamic forces on the flapping wing are not much affected by considerable twist,but affected by camber deformation.The effect of combined camber and twist deformation is similar to that of camber deformation.With a deformation of 6% camber and 20°twist(typical values observed for wings of many insects),lift is increased bv 10%～20%and lift-to-drag ratio by around 10%compared with the case of a rigid flat-plate wing.As a result.the deformation can increase the maximum lift coefficient of an insect.and reduce its power requirement for flight.For example,for a hovering bumblebee with dynamically deforming wings(6?mber and 20°twist),aerodynamic power required is reduced by about 16%compared with the case of rigid wings.     

昆虫拍翼方式的非定常流动物理再探讨

基于提出的理论模化方法来探讨昆虫拍翼方式的非定常流动物理. 以悬停飞行为 例,通过对拍翼运动的分析,不仅解释了昆虫利用高频拍翼的方式为何能够克服低雷诺数带 来的气动局限性(St \gg 1/Re),而且还指出高升力产生和调节的3个流动 控制因素：(1) 由于拍翼的变速运动即时引起了流体动力响应,这种附加惯性效应 可产生瞬时的高升力; (2) 保持前缘涡不脱离翼面有助于减少升力的下降; (3) 增大后缘涡的强度并加速其脱离后缘能够有效地提高升力.     

Power extraction efficiency improvement of a fully-activated flapping foil: With the help of an auxiliary rotating foil

The power extraction efficiency improvement of a fully-activated flapping foil with the help of an auxiliary rotating foil is numerically examined in this work. A NACA0015 airfoil is placed in a two-dimensional laminar flow and synchronously performs the imposed pitching and plunging motions. An auxiliary smaller foil, which rotates about its center, is arranged below the flapping foil. As a consequence, the vortex interaction between the flapping foil and the rotating foil occurs. At a Reynolds number of 1100 and the position of the pitching axis at one-third chord, the effects of the distance between the flapping foil and the auxiliary foil, the phase difference between the rotating motion and the flapping motion as well as the frequency of flapping motion on the power extraction performance are systematically investigated. It is found that compared to the single flapping foil, the efficiency of power extraction for the flapping foil with an auxiliary device can be improved. Based on the numerical analysis, it is indicated that the enhanced plunging contribution, which is caused by the increased lift force owing to the vortex interaction, directly helps the efficiency improvement.     

电磁力控制翼型绕流分离的增升减阻效率研究

电磁力可有效对流体流动进行控制,增升减阻,抑制流动分离,制约其推广应用的瓶颈为控制效率问题.为提高其控制效率,基于翼型绕流的电磁力控制,对电磁力增升减阻的控制效率问题进行数值研究. 根据能量守恒定律,推导电磁力控制能耗的比,基于升力和阻力计算节省能量. 定义电磁力的控制效率为能量节省与电磁力控制所需能耗的比值,研究不同工况下电磁力增升减阻的控制效率. 发现在控制开始阶段,电磁力能量主要消耗在增加边界层流体的动能上,电磁力控制效率非常低,但电磁力控制效率会随着电磁力工作时间的增长而增加;电磁力控制效率随着来流速度的增加呈指数下降;通过增加电磁力激活板的输入能量可增强电磁力的控制效果,但无法明显增加其控制效率.      

翼型绕流的电磁力控制

将表面包覆电磁激活板的翼型,按一定的攻角,置于流动的弱电介质溶液中,电磁激活板可产生作用于流体的切向电磁力(Lorentz力),从而改变流体边界层的结构. 在转动水槽中,对翼型绕流及电磁力控制下的绕流形态进行了实验研究. 结果表明,未加电磁力时,前缘涡的脱落点是不确定的,与流场具体条件有关,而后缘涡仅在尖角处脱落. 前缘涡与后缘涡相互影响,并周期性的脱体,在尾部形成涡街. 施加电磁力后,当力的方向与流动方向相同时,可以在一定程度上抑制分离,消除涡街,其效果与减小攻角类似. 加反向电磁力时,则相当于加大攻角,在翼型体的背风面形成涡街.      

Hydrodynamics of flow over a transversely oscillating circular cylinder beneath a free surface

In this paper, hydrodynamic force coefficients and wake vortex structures of uniform flow over a transversely oscillating circular cylinder beneath a free surface were numerically investigated by an adaptive Cartesian cut-cell/level-set method. At a fixed Reynolds number, 100, a series of simulations covering three Froude numbers, two submergence depths, and three oscillation amplitudes were performed over a wide range of oscillation frequency. Results show that, for a deeply submerged cylinder with sufficiently large oscillation amplitudes, both the lift amplitude jump and the lift phase sharp drop exist, not accompanied by significant changes of vortex shedding timing. The near-cylinder vortex structure changes when the lift amplitude jump occurs. For a cylinder oscillating beneath a free surface, larger oscillation amplitude or submergence depth causes higher time-averaged drag for frequency ratio (=oscillation frequency/natural vortex shedding frequency) greater than 1.25. All near-free-surface cases exhibit negative time-averaged lift the magnitude of which increases with decreasing submergence depth. In contrast to a deeply submerged cylinder, occurrences of beating in the temporal variation of lift are fewer for a cylinder oscillating beneath a free surface, especially for small submergence depth. For the highest Froude number investigated, the lift frequency is locked to the cylinder oscillation frequency for frequency ratios higher than one. The vortex shedding mode tends to be double-row for deep and single-row for shallow submergence. Proximity to the free surface would change or destroy the near-cylinder vortex structure characteristic of deep-submergence cases. The lift amplitude jump is smoother for smaller submergence depth. Similar to deep-submergence cases, the vortex shedding frequency is not necessarily the same as the primary-mode frequency of the lift coefficient. The frequency of the induced free surface wave is exactly the cylinder oscillation frequency. The trends of wave length variation with the Froude number and frequency ratio agree with those predicted by the linear theory of small-amplitude free surface waves.     

Motion of a slender body near the free surface of a compressible fluid

An analytic solution to the problem of motion of a slender rigid body in a semi-infinite domain of a compressible fluid is obtained for the case when the body moves in parallel to the free surface at a constant velocity. This problem is similar to the problem of motion of a hydrofoil ship whose wing-like device allows it to lift its hull above the water surface and to decrease the friction and drag forces limiting the speed of usual ships. During its motion in water, a hydrofoil produces a lift force. The obtained analytic solution allows one to derive explicit expressions for the drag force and for the lift force in the limiting cases of relatively small and large depths. When depth is small, the drag force is greater than that in an infinite medium, since the wave drag is additionally evolved. When the velocity increases and approaches the sound velocity, the forces exerted on the body increase without limit, which is typical for a linear formulation of the problem.