Growth of epitaxial ZnO films on Si (1 1 1) substrates with Cr compound buffer layer by plasma-assisted molecular beam epitaxy

Single crystalline ZnO film was grown on (1 1 1) Si substrate through employing an oxidized CrN buffer layer by plasma-assisted molecular beam epitaxy. Single crystalline characteristics were confirmed from in-situ reflection high energy electron diffraction, X-ray pole figure measurement, and transmission electron diffraction pattern, consistently. Epitaxial relationship between ZnO film and Si substrate is determined to be (0 0 0 1)_ZnO‖(1 1 1)_Si and [1 1 2¯ 0]_ZnO‖[0 1 1]_Si. Full-width at half-maximums (FWHMs) of (0 0 0 2) and (1 0 1¯ 1) X-ray rocking curves (XRCs) were 1.379° and 3.634°, respectively, which were significantly smaller than the FWHMs (4.532° and 32.8°, respectively) of the ZnO film grown directly on Si (1 1 1) substrate without any buffer. Total dislocation density in the top region of film was estimated to be ∼5×10⁹ cm⁻². Most of dislocations have a screw type component, which is different from the general cases of ZnO films with the major threading dislocations with an edge component.     

ZnO growth on Si with low-temperature ZnO buffer layers by ECR-assisted MBE

High-quality ZnO films were grown on Si(1 0 0) substrates with low-temperature (LT) ZnO buffer layers by an electron cyclotron resonance (ECR)-assisted molecular-beam epitaxy (MBE). In order to investigate the optimized buffer layer temperature, ZnO buffer layers of about 1.1 μm were grown at different growth temperatures of 350, 450 and 550 °C, followed by identical high-temperature (HT) ZnO films with the thickness of 0.7 μm at 550 °C. A ZnO buffer layer with a growth temperature of 450 °C (450 °C-buffer sample) was found to greatly enhance the crystalline quality of the top ZnO film compared to others. The root mean square (RMS) roughness (3.3 nm) of its surface is the smallest, compared to the 350 °C-buffer sample (6.7 nm), the 550 °C-buffer sample (7.4 nm), and the sample without a buffer layer (6.8 nm). X-ray diffraction (XRD), photoluminescence (PL) and Raman scattering measurements were carried out on these samples at room temperature (RT) in order to characterize the crystalline quality of ZnO films. The preferential c-axis orientations of (0 0 2) ZnO were observed in the XRD spectra. The full-width at half-maximum (FWHM) value of the 450 °C-buffer sample was the narrowest as 0.209°, which indicated that the ZnO film with a buffer layer grown at this temperature was better for the subsequent ZnO growth at elevated temperature of 550 °C. Consistent with these results, the 450 °C-buffer sample exhibits the highest intensity and the smallest FWHM (130 meV) of the ultraviolet (UV) emission at 375 nm in the PL spectrum. The ZnO characteristic peak at 438.6 cm⁻¹ was found in Raman scattering spectra for all films with buffers, which is corresponding to the E₂ mode.     

Growth of high-quality ZnO single crystals by seeded CVT using the newly designed ampoule

The high-quality ZnO single crystals were grown by seeded chemical vapor transport (CVT) in a newly designed ampoule using carbon as a transport agent. The well-faceted crystal of about 5×5×5 mm³ can be grown reproducibly. Secondary ion mass spectroscopy (SIMS) analysis, X-ray rocking curve (XRC) and photoluminescence (PL) measurements demonstrate that the grown single crystal is of high purity and high crystallinity.     

Synthesis and optical properties of Ce-doped ZnO hexagonal nanoplatelets

Single crystalline Ce-doped ZnO hexagonal nanoplatelets are successfully synthesized. Zinc acetate, cerium nitrate, potassium hydroxide and poly vinyl alcohol were mixed together and transferred to a 100 mL Teflon-lined stainless steel autoclave kept at 150 °C for 24 h. The obtained precipitant is calcined at 600 °C. The morphology and microstructure were determined by field emission scanning electron microscopy (FE-SEM), X-ray diffraction transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX) and photoluminescence (PL) spectroscopy. The investigation confirmed that the products were of the wurtzite structure of ZnO. The doped hexagonal nanoplatelets have edge length 25 nm and thickness 11 nm. EDX result showed that the amount of Ce in the product is about 15%. Photoluminescence of these doped hexagonal nanoplatelets exhibits a blue shift and weak ultraviolet (UV) emission peak, compared with pure ZnO, which may be induced by Ce-doping. The growth mechanism of the doped hexagonal nanoplatelets was also discussed.     

在Si(100)上以AlN作过渡层低温外延生长ZnO薄膜

采用脉冲激光沉积(PLD)方法在Si(100)上成功生长了高度c轴取向的AlN薄膜,并以此为衬底,实现了ZnO薄膜的低温准外延生长.通过X射线衍射(XRD)、原子力显微镜(AFM)以及荧光分光光度计表征ZnO薄膜的结构、表面形貌和发光性能.结果表明,ZnO薄膜能在AlN过渡层上沿c轴准外延生长,采用AlN过渡层后,其荧光强度也有大幅提高.     

Epitaxial growth of ZnO films on thin FeO(1 1 1) layers

Thin FeO(1 1 1) buffer layers prepared on Mo(1 1 0) substrate were used to grow ordered ZnO films under ultrahigh vacuum condition, and were in situ characterized by various surface analytical techniques. A chemical interaction between Zn (or ZnO) and FeO(1 1 1) can effectively lower the interfacial energy, which is in favor of an epitaxial growth of ZnO on FeO layers. Compared with the MgO(1 1 1) buffer layer used for the growth of ZnO(0 0 0 1) on sapphire (0 0 0 1) surface, the FeO(1 1 1) thin films might be a better one because it is more thermally stable. Our experimental results provide constructive information on the growth mechanism of ZnO-based materials, which is helpful for further understanding the growth mechanism of related oxide materials.     

Growth and characterization of GaAs layers on polished Ge/Si by selective aspect ratio trapping

Epitaxial GaAs layers have been deposited on polished Ge film grown on exactly (0 0 1) oriented Si substrate by metal-organic chemical vapor deposition (MOCVD) via aspect ratio trapping (ART) method. Double-crystal X-ray diffraction shows that the full-width at half-maximum (FWHM) of the (4 0 0) reflection obtained from 1 μm GaAs is 140 arcsec. Scanning electron microscopy (SEM) of the GaAs layer surface shows that the amount of antiphase domain defects (APD) raised from GaAs/Ge interface using Ge ART on Si is dramatically reduced compared to GaAs layers grown on exact (0 0 1) Ge substrate. Defect reduction and Ge diffusion at vicinal GaAs/Ge interface were investigated via cross-section transmission electron microscopy (X-TEM) and secondary ion mass spectrometry (SIMS). Film morphology and optical properties were evaluated via SEM and room temperature photoluminescence (PL).     

MOVPE growth of InN buffer layers on sapphire

We report on the MOCVD growth of InN buffer layers on sapphire substrate for InN growth. The approach used assumes that an optimized InN buffer layer has to exhibit at least the same crystalline quality and sapphire surface coverage than the GaN buffer layers allowing to grow high crystalline quality GaN on sapphire. The buffer layers were characterized by AFM and GID measurements. Sapphire nitridation was investigated: it has a strong influence on in-plane crystalline quality. Two kinds of buffer layers were optimized according to the GaN buffer layer specifications: one of them only presented In droplets at its surface. It was shown that the small amount of In droplets increases the adatoms mobility of the main layer overgrown, leading to a 25% decrease of its in-plane mosaicity, compared to InN films directly grown on sapphire. To achieve a same improvement on InN buffer layer free of In droplets, the InN main layer growth temperature had to be increased from 550 °C. to 600 °C.     

Influence of amorphous buffer layers on the crystallinity of sputter-deposited undoped ZnO films

Undoped ZnO films were deposited by radio frequency (RF) magnetron sputtering on amorphous buffer layers such as SiO_x, SiO_xN_y, and SiN_x prepared by plasma enhanced chemical vapor deposition (PECVD) for dielectric layer in thin film transistor (TFT) application. ZnO was also deposited directly on glass and quartz substrate for comparison. It was found that continuous films were formed in the thickness up to 10 nm on all buffer layers. The crystallinity of ZnO films was improved in the order on quartz>SiO_x >SiO_xN_y>glass>SiN_x according to the investigated intensities of (0 0 2) XRD peaks. The crystallite sizes of ZnO were in the order of SiO_x～glass >SiN_x. Stable XRD parameters of ZnO thin films were obtained to the thickness from 40 to 100 nm grown on SiO_x insulator for TFT application. Investigation of the ZnO thin films by atomic force microscope (AFM) revealed that grain size and roughness obtained on SiN_x were larger than those on SiO_x and glass. Hence, both nucleation and crystallinity of sputtered ZnO thin films remarkably depended on amorphous buffer layers.     

Structural and optical properties of single-crystal ZnMgO thin films grown on sapphire and ZnO substrates by RF magnetron sputtering

High-quality ZnMgO films were grown by the radio frequency (RF) magnetron sputtering technique in pure oxygen ambient. Single-crystal films were obtained, when the Mg concentration was Zn_0.87Mg_0.13O or lower in the case of ZnMgO/Al₂O₃ and when it was Zn_0.65Mg_0.35O or lower in the case of ZnMgO/ZnO. Polycrystalline films were obtained when the growth temperature was lower than 500 °C, regardless of the Mg concentration. Position of the photoluminescence (PL) ultraviolet (UV) peak of the ZnMgO film shifted with the addition of Mg, from 3.33 eV (ZnO) to 3.51 eV (Zn_0.87Mg_0.13O) and 3.70 eV (Zn_0.65Mg_0.35O). It was also observed that growth of the ZnMgO films at higher temperature resulted in higher band-gap energy. It was proposed that this phenomenon is because concentration of the substitutional Mg atoms occupying Zn site is increased as the growth temperature increases.     

Growth of ZnO crystal by self-flux method using Zn solvent

Zinc oxide (ZnO) single crystal was grown, for the first time, by the self-flux method using a high-purity zinc solvent saturated with oxygen. ZnO crystals were successfully grown in the solvent by moving a growing crystal slowly, at about 17 mm/day along a temperature gradient (1.5 °C/mm) in a furnace, from 1050 to 500 °C. Hexagonal single crystals 1–3 mm in length and 0.5–1 mm in thickness were obtained. Energy-dispersive X-ray diffraction, secondary ion mass spectrometry, and photoluminescence confirmed that the purity and crystallinity of the ZnO crystals grown in this work were high.     

Fabrication of (1 1 1)-oriented Si layers on SiO2 substrates by an aluminum-induced crystallization method and subsequent growth of semiconducting BaSi2 layers for photovoltaic application

We have prepared (1 1 1)-oriented Si layers on SiO₂ (fused silica) substrates from amorphous-Si(a-Si)/Al or Al/a-Si stacked layers using an aluminum-induced crystallization (AIC) method. The X-ray diffraction (XRD) intensity from the (1 1 1) planes of Si was found to depend significantly on growth conditions such as the thicknesses of Si and Al, deposition order (a-Si/Al or Al/a-Si on SiO₂), deposition technique (sputtering or vacuum evaporation) and exposure time of the Al layer to air before the deposition of Si. The crystal orientation of the Si layers was confirmed by θ−2θ, 2θ XRD and electron backscatter diffraction (EBSD). The photoresponse properties of semiconducting BaSi₂ films formed on the (1 1 1)-oriented Si layers by the AIC method were measured at room temperature. Photocurrents were clearly observed for photon energies greater than 1.25 eV. The external quantum efficiencies of the BaSi₂ were also evaluated.     

In-situ and ex-situ ZnO nanorod growth on ZnO homo-buffer layers

Vertically well-aligned ZnO nanorods were fabricated in-situ and ex-situ on ZnO homo-buffer layers using catalyst-free metal-organic chemical vapor deposition. Field-emission electron microscopy measurements demonstrated that the nanorods were well aligned and had a uniform diameter of 70–100 nm depending on the growth temperature, irrespective of growth conditions, in-situ and ex-situ. X-ray diffraction measurements demonstrated that the ZnO nanorods and the ZnO buffer layers had a wurtzite structure, and that the crystal quality of the nanorods grown on a smooth surface was better than that of the nanorods grown on a rough surface. Field-emission transmission electron microscopy measurements revealed the presence of a disordered layer at the interface of the nanorod and the buffer layer.     

High-resolution X-ray diffraction analysis on HVPE-grown thick GaN layers

The threading dislocation density of hydride vapor phase epitaxy (HVPE)-grown thick GaN layers was measured by high-resolution X-ray diffraction (HR-XRD). Three models were compared, namely mosaic model, Kaganer model and modified Kaganer model. X-ray rocking curves (XRC) of (0 0 0 2), (1 0 1¯ 5), (1 0 1¯ 4), (1 0 1¯ 3), (1 0 1¯ 2), (1 0 1¯ 1) and (1 0 1¯ 0) planes were recorded for quantitative analysis. The screw-, edge-, and mixed-type threading dislocation densities were simulated from the XRD line profile by using the three models. The dislocation density was also measured by atomic force microscopy (AFM), wet chemical etching and cathodoluminescence (CL). The results showed that the Kaganer model was more physically precise and well explained the rocking curve broadening for HVPE-grown high-quality GaN compared with the mosaic model. Assuming a randomly distributed threading dislocation configuration, we modified the Kaganer model. Based on the modified Kaganer model, the edge and screw threading dislocation densities in HVPE-grown GaN thick films ranging from 20 μm up to 700 μm were analyzed. It was shown that screw-type dislocation density decreased more rapidly than edge-type dislocation with increase in film thickness.     

Sol–gel preparation and photoluminescence properties of Ce-activated Y3Al5O12 nano-sized powders

Trivalent cerium-doped yttrium aluminum garnet (YAG:Ce³⁺) nanoparticles were successfully prepared by a facile sol–gel technique. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and photoluminescence (PL) spectroscopy were used to characterize the as-prepared phosphors. Well-crystallized fine nanoparticles were obtained at 1000 °C. Single-crystal nanoparticles with irregular shapes were obtained, with crystallite sizes ranging between 20 and 60 nm. PL intensity of the particles increased monotonically with decreasing Ce doping concentration and showed the maximum value at 0.1 at%.     

GaN-based nitride semiconductor films deposited on nitrified HfO2/Si substrate by molecular beam epitaxy

Nitrified HfO₂/Si substrate was used to grow GaN-based film with molecular beam epitaxy. Four-period InGaN/GaN layered structure and p/n junction were deposited on the nitrified HfO₂/Si. X-ray photoelectron spectroscopy (XPS) result shows that N was effectively incorporated into the HfO₂. The crystallographic relationship of the GaN/HfO₂/Si is GaN(0 0 0 2)∥HfO₂(1 1 1)∥Si(1 1 1). Temperature-dependent photoluminescence (PL), PL peak wavelength, PL peak intensity, and PL full-width at half-maximum of the p/n junction were investigated. Light-emitting diode was fabricated from the p/n junction. Red light was emitted at low voltage and yellow light was emitted when increasing the voltage.     

High intense UV-luminescence of nanocrystalline ZnO thin films prepared by thermal oxidation of ZnS thin films

High quality zinc oxide (ZnO) films were obtained by thermal oxidation of high quality ZnS films. The ZnS films were deposited on a Si substrate by a low-pressure metalorganic chemical vapor deposition technique. X-ray diffraction spectra indicate that high quality ZnO films possessing a polycrystalline hexagonal wurtzite structure with preferred orientation of (0 0 2) were obtained. A fourth order LO Raman scattering was observed in the films. In photoluminescence (PL) measurements, a strong PL with a full-width at half-maximum of 10 nm around 380 nm was obtained for the samples annealed at 900°C at room temperature. The maximum PL intensity ratio of the UV emission to the deep-level emission is 28 at room temperature, providing evidence of the high quality of the nanocrystalline ZnO films.     

Chemically assisted vapour transport for bulk ZnO crystal growth

A chemically assisted vapour phase transport (CVT) method is proposed for the growth of bulk ZnO crystals. Thermodynamic computations have confirmed the possibility of using CO as a sublimation activator for enhancing the sublimation rate of the feed material in a large range of pressures (10⁻³ to 1 atm) and temperatures (800–1200 °C). Growth runs in a specific and patented design yielded single ZnO crystals up to 46 mm in diameter and 8 mm in thickness, with growth rates up to 400 μm/h. These values are compatible with an industrial production rate. N type ZnO crystals (μ=182 cm²/(V s) and n=7 10¹⁵ cm⁻³) obtained by this CVT method (Chemical Vapour Transport) present a high level of purity (10–30 times better than hydrothermal ZnO crystals), which may be an advantage for obtaining p-type doped layers ([Li] and [Al] <10⁺¹⁵ cm⁻³). Structural (HR-XRD), defect density (EPD), electrical (Hall measurements) and optical (photoluminescence) properties are presented.     

Suppression of phase separation in InGaN layers grown on lattice-matched ZnO substrates

Sapphire and SiC are typical substrates used for GaN growth. However, they are non-native substrates and result in highly defective materials. The use of ZnO substrates can result in perfect lattice-matched conditions for 22% indium InGaN layers, which have been found to suppress phase separation compared to the same growths on sapphire. InGaN layers were grown on standard (0 0 0 2) GaN template/sapphire and (0 0 0 1) ZnO substrates by metalorganic chemical vapor deposition. These two substrates exhibited two distinct states of strain relaxation, which have direct effects on phase separation. InGaN with 32% indium exhibited phase separation when grown on sapphire. Sapphire samples were compared with corresponding growths on ZnO, which showed no evidence of phase separation with indium content as high as 43%. Additional studies in Si-doping of InGaN films also strongly induced phase separation in the films on sapphire compared with those on ZnO. High-resolution transmission electron microscopy results showed perfectly matched crystals at the GaN buffer/ZnO interface. This implied that InGaN with high indium content may stay completely strained on a thin GaN buffer. This method of lattice matching InGaN on ZnO offers a new approach to grow efficient emitters.     

Low-temperature/high-temperature AlN superlattice buffer layers for high-quality AlxGa1−xN on Si (1 1 1)

We present MOVPE-grown, high-quality Al_xGa_1−x N layers with Al content up to x=0.65 on Si (1 1 1) substrates. Crack-free layers with smooth surface and low defect density are obtained with optimized AlN-based seeding and buffer layers. High-temperature AlN seeding layers and (low temperature (LT)/high temperature (HT)) AlN-based superlattices (SLs) as buffer layers are efficient in reducing the dislocation density and in-plane residual strain. The crystalline quality of Al_xGa_1−xN was characterized by high-resolution X-ray diffraction (XRD). With optimized AlN-based seeding and SL buffer layers, best ω-FWHMs of the (0 0 0 2) reflection of 540 and 1400 arcsec for the (1 0 1¯ 0) reflection were achieved for a ∼1-μm-thick Al_0.1Ga_0.9N layer and 1010 and 1560 arcsec for the (0 0 0 2) and (1 0 1¯ 0) reflection of a ∼500-nm-thick Al_0.65Ga_0.35N layer. AFM and FE-SEM measurements were used to study the surface morphology and TEM cross-section measurements to determine the dislocation behaviour. With a high crystalline quality and good optical properties, Al_xGa_1−x N layers can be applied to grow electronic and optoelectronic device structures on silicon substrates in further investigations.