Growth of epitaxial ZnO films on Si (1 1 1) substrates with Cr compound buffer layer by plasma-assisted molecular beam epitaxy

Single crystalline ZnO film was grown on (1 1 1) Si substrate through employing an oxidized CrN buffer layer by plasma-assisted molecular beam epitaxy. Single crystalline characteristics were confirmed from in-situ reflection high energy electron diffraction, X-ray pole figure measurement, and transmission electron diffraction pattern, consistently. Epitaxial relationship between ZnO film and Si substrate is determined to be (0 0 0 1)_ZnO‖(1 1 1)_Si and [1 1 2¯ 0]_ZnO‖[0 1 1]_Si. Full-width at half-maximums (FWHMs) of (0 0 0 2) and (1 0 1¯ 1) X-ray rocking curves (XRCs) were 1.379° and 3.634°, respectively, which were significantly smaller than the FWHMs (4.532° and 32.8°, respectively) of the ZnO film grown directly on Si (1 1 1) substrate without any buffer. Total dislocation density in the top region of film was estimated to be ∼5×10⁹ cm⁻². Most of dislocations have a screw type component, which is different from the general cases of ZnO films with the major threading dislocations with an edge component.     

Molecular beam epitaxial growth of hexagonal boron nitride on Ni(1 1 1) substrate

We demonstrate hexagonal boron nitride (h-BN) epitaxial growth on Ni(1 1 1) substrate by molecular beam epitaxy (MBE) at 890 °C. Elemental boron evaporated by an electron-beam gun and active nitrogen generated by a radio-frequency (RF) plasma source were used as the group-III and -V sources, respectively. Reflection high-energy electron diffraction revealed a streaky (1×1) pattern, indicative of an atomically flat surface in the ongoing growth. Correspondingly, atomic force microscopy images exhibit atomically smooth surface of the resulting h-BN film. X-ray diffraction characterization confirmed the crystallinity of the epitaxial film to be h-BN, and its X-ray rocking curve has a full-width at half-maximum of 0.61°, which is the narrowest ever reported for h-BN thin film. The epitaxial alignments between the h-BN film and the Ni substrate were determined to be [0 0 0 1]_h−BN∥[1 1 1]_Ni, [1 1 2¯ 0]_h−BN∥[1¯ 1 0]_Ni, and [1 1¯ 0 0]_h−BN∥[1¯ 1¯ 2]_Ni.     

One-sidewall-seeded epitaxial lateral overgrowth of a-plane GaN by metalorganic vapor-phase epitaxy

The selective regrowth of GaN during sidewall-seeded epitaxial lateral overgrowth was performed. In addition to adjusting the V/III ratio, control of offset angle of the sidewall was found to be effective for realizing one-sidewall-seeded a-plane (1 1 2¯ 0) GaN on r-plane (1 1¯ 0 2) sapphire. The number of coalescence regions on the grooves was reduced, and threading-dislocation and stacking-fault densities as low as 10⁶–10⁷ cm⁻² and 10³–10⁴ cm⁻¹, respectively, were successfully realized.     

Structural and infrared properties of zinc oxide film and nanowires

The structural and infrared properties of the highly (00.2) oriented ZnO film, randomly grown Au-catalyzed ZnO nanowires (NWs) and vertically aligned self-catalyzed ZnO NWs were compared. In the XRD analysis, (0 0 2) diffraction intensity of self-catalyzed ZnO NWs was enhanced mainly attributed to the preferential growth of NWs in [0 0 0 1] as compared to the ZnO film and the randomly grown Au-catalyzed ZnO NWs. The high UV-to-green emission ratio of self-catalyzed ZnO NWs in room temperature PL measurement indicates that they had a better crystal quality as compared to Au-catalyzed ZnO NWs and ZnO film. Infrared spectroscopy has been used to characterize these films and nanowires too. The phonon peak 407 cm⁻¹ which related to the transverse optical (TO) vibrations perpendicular to the optical axis was observed in the IR reflectivity measurements on the highly c-oriented ZnO film. The IR peaks that appeared in the 550–580 cm⁻¹ region of the spectra of the specimens could be assigned to the ZnO NWs as it was not observed in the ZnO film. These peaks were observed in the 550–580 cm⁻¹ region in both s- and p-polarized light for the randomly grown Au-catalyzed ZnO NWs. In contrast, the IR peak at 580 cm⁻¹ was clearly shown in p-polarized light but not in the s-polarized light for vertically aligned ZnO NWs. This indicated that the vibration was polarized along the vertically aligned ZnO NWs. The (00.2) orientation of the ZnO specimens could be identified by comparing the p- and s-polarized IR spectra.     

Investigation of nonpolar (1 1 2¯ 0) a-plane ZnO films grown under various Zn/O ratios by plasma-assisted molecular beam epitaxy

Structural and optical properties of nonpolar a-plane ZnO films grown with different II/VI ratios on r-plane sapphire substrates by plasma-assisted molecular beam epitaxy were investigated. Even by increasing the II/VI ratio across the stoichiometric flux condition a consistent surface morphology of striated stripes along the ZnO 〈0 0 0 1〉 direction without any pit formation was observed, which is contrary to polar c-plane ZnO films. Root mean square surface roughness, full width at half maximum values of X-ray rocking curves, defect densities, and photoluminescence were changed with the II/VI ratio. The sample grown with stoichiometric flux condition showed the lowest value of rms roughness, the smallest threading dislocation and stacking fault densities of ∼4.7×10⁸ cm⁻² and ∼9.5×10⁴ cm⁻¹, respectively, and the highest intensity of D^oX peak. These results imply that the stoichiometric flux growth condition is suitable to obtain superior structural and optical properties compared to other flux conditions.     

Electrical properties and deep traps spectra in undoped M-plane GaN films prepared by standard MOCVD and by selective lateral overgrowth

Electrical properties, deep traps spectra and structural performance were studied for m-GaN films grown on m-SiC substrates by standard metalorganic chemical vapor deposition (MOCVD) and by MOCVD with lateral overgrowth (ELO) or sidewall lateral overgrowth (SELO). Standard MOCVD m-GaN films with a very high dislocation density over 10⁹ cm⁻² are semi-insulating n-type with the Fermi level pinned near E_c−0.7 eV when grown at high V/III ratio. For lower V/III they become more highly conducting, with the electrical properties still dominated by a high density (∼10¹⁶ cm⁻³) of E_c−0.6 eV electron traps. Lateral overgrowth that reduces the dislocation density by several orders of magnitude results in a marked increase in the uncompensated shallow donor density (∼10¹⁵ cm⁻³) and a substantial decrease of the density of major electron traps at E_c−0.25 and E_c−0.6 eV (down to about 10¹⁴ cm⁻³). Possible explanations are briefly discussed.     

The effect of composition on UV-vis-NIR spectra of iron doped glasses in the systems Na2O/MgO/SiO2 and Na2O/MgO/Al2O3/SiO2

Glasses with the compositions xNa₂O · 10MgO · (90 − x)SiO₂, 10Na₂O · xMgO · (90 − x)SiO₂, 5Na₂O · 15MgO · xAl₂O₃ · (80 − x)SiO₂, xNa₂O · 10MgO · 10Al₂O₃ · (80 − x)SiO₂, 10Na₂O · 10MgO · xAl₂O₃ · (80 − x)SiO₂, 10Na₂O · 5MgO · 10Al₂O₃ · (80 − x)SiO₂ were melted and studied using UV-vis-NIR spectroscopy in the wavenumber range from 5000 to 30 000 cm⁻¹. At [Al₂O₃] > [Na₂O], the UV-cut off is strongly shifted to smaller wavenumbers and the NIR peak at around 10 000 cm⁻¹ attributed to Fe²⁺ in sixfold coordination gets narrower. Furthermore, the intensity of the NIR peak at 5500 cm⁻¹ increases. This is explained by the incorporation of iron in the respective glass structures.     

SIMS and Raman characterizations of ZnO:N thin films grown by MOCVD

Nitrogen was incorporated into ZnO films grown by metalorganic chemical vapour deposition (MOCVD) on ZnO substrates using DMZn-TEN, tert-butanol and diallylamine, respectively, as zinc, oxygen and doping sources. The carrier gas was either hydrogen or nitrogen and the partial pressure ratio (R_VI/II) was varied in order to favor the nitrogen incorporation and/or reduce carbon related defects. The ZnO films have been characterized by Micro-Raman scattering and SIMS measurements. SIMS measurements confirm the nitrogen incorporation with concentrations extending from ∼10¹⁹ cm⁻³ to ∼4×10²⁰ cm⁻³. Raman spectra show nitrogen local vibration modes in films grown at low R_VI/II ratio and using H₂ as carrier gas. However, a vibration band attributed to carbon clusters dominates the Raman spectra for films grown with N₂ carrier. The contribution of N complexes was discussed. The strain was calculated for the as-grown and annealed films and it changes from tensile to compressive after annealing.     

Chemically assisted vapour transport for bulk ZnO crystal growth

A chemically assisted vapour phase transport (CVT) method is proposed for the growth of bulk ZnO crystals. Thermodynamic computations have confirmed the possibility of using CO as a sublimation activator for enhancing the sublimation rate of the feed material in a large range of pressures (10⁻³ to 1 atm) and temperatures (800–1200 °C). Growth runs in a specific and patented design yielded single ZnO crystals up to 46 mm in diameter and 8 mm in thickness, with growth rates up to 400 μm/h. These values are compatible with an industrial production rate. N type ZnO crystals (μ=182 cm²/(V s) and n=7 10¹⁵ cm⁻³) obtained by this CVT method (Chemical Vapour Transport) present a high level of purity (10–30 times better than hydrothermal ZnO crystals), which may be an advantage for obtaining p-type doped layers ([Li] and [Al] <10⁺¹⁵ cm⁻³). Structural (HR-XRD), defect density (EPD), electrical (Hall measurements) and optical (photoluminescence) properties are presented.     

Defect reduction in nonpolar and semipolar GaN using scandium nitride interlayers

Nonpolar (1 1 2¯ 0) and semipolar (1 1 2¯ 2) GaN films were grown on sapphire by metalorganic vapour phase epitaxy using ScN interlayers of varying thicknesses. A 5 nm interlayer reduced basal plane stacking fault (BSF) densities in nonpolar films by a factor of 2 and threading dislocation (TD) densities by a factor of 100 to (1.8±0.2)×10⁹ cm⁻². An 8.5 nm interlayer reduced BSF densities in semipolar films by a factor of 5 and reduced TD densities by a factor of 200 to (1.5±0.3)×10⁸ cm⁻². Nonpolar film surface roughnesses were reduced by a factor of 20.     

Low-temperature/high-temperature AlN superlattice buffer layers for high-quality AlxGa1−xN on Si (1 1 1)

We present MOVPE-grown, high-quality Al_xGa_1−x N layers with Al content up to x=0.65 on Si (1 1 1) substrates. Crack-free layers with smooth surface and low defect density are obtained with optimized AlN-based seeding and buffer layers. High-temperature AlN seeding layers and (low temperature (LT)/high temperature (HT)) AlN-based superlattices (SLs) as buffer layers are efficient in reducing the dislocation density and in-plane residual strain. The crystalline quality of Al_xGa_1−xN was characterized by high-resolution X-ray diffraction (XRD). With optimized AlN-based seeding and SL buffer layers, best ω-FWHMs of the (0 0 0 2) reflection of 540 and 1400 arcsec for the (1 0 1¯ 0) reflection were achieved for a ∼1-μm-thick Al_0.1Ga_0.9N layer and 1010 and 1560 arcsec for the (0 0 0 2) and (1 0 1¯ 0) reflection of a ∼500-nm-thick Al_0.65Ga_0.35N layer. AFM and FE-SEM measurements were used to study the surface morphology and TEM cross-section measurements to determine the dislocation behaviour. With a high crystalline quality and good optical properties, Al_xGa_1−x N layers can be applied to grow electronic and optoelectronic device structures on silicon substrates in further investigations.     

Assessment of defect reduction methods for nonpolar a-plane GaN grown on r-plane sapphire

This work assesses the relative effectiveness of four techniques to reduce the defect density in heteroepitaxial nonpolar a-plane GaN films grown on r-plane sapphire by metalorganic vapour phase epitaxy (MOVPE). The defect reduction techniques studied were: 3D–2D growth, SiN_x interlayers, ScN interlayers and epitaxial lateral overgrowth (ELOG). Plan-view transmission electron microscopy (TEM) showed that the GaN layer grown in a 2D fashion had a dislocation and basal-plane stacking fault (BSF) density of (1.9±0.2)×10¹¹ cm⁻² and (1.1±0.9)×10⁶ cm⁻¹, respectively. The dislocation and BSF densities were reduced by all methods compared to this 2D-grown layer (used as a seed layer for the interlayer and ELOG methods). The greatest reduction was achieved in the (0 0 0 1) wing of the ELOG sample, where the dislocation density was <1×10⁶ cm⁻² and BSF density was (2.0±0.7)×10⁴ cm⁻¹. Of the in-situ techniques, SiN_x interlayers were most effective: the interlayer with the highest surface coverage that was studied reduced the BSF density to (4.0±0.2)×10⁵ cm⁻¹ and the dislocation density was lowered by over two orders of magnitude to (3.5±0.2)×10⁸ cm⁻².     

Properties of Ge-doped,high-quality bulk GaN crystals fabricated by hydride vapor phase epitaxy

We investigated the properties of Ge-doped, high-quality bulk GaN crystals with Ge concentrations up to 2.4×10¹⁹ cm⁻³. The Ge-doped crystals were fabricated by hydride vapor phase epitaxy with GeCl₄ as the dopant source. Cathodoluminescence imaging revealed no increase in the dislocation density at even the highest Ge concentration, with values as low as 3.4×10⁶ cm⁻². The carrier concentration, as determined by Hall measurement, was almost identical to the combined concentration of Ge and unintentionally incorporated Si. The electron mobilities were 260 and 146 cm² V⁻¹ s⁻¹ for n=3.3×10¹⁸ and 3.35×10¹⁹ cm⁻³, respectively; these values are markedly larger than those reported in the past for Ge-doped GaN thin films. The optical absorption coefficient was quite small below the band gap energy; it slightly increased with increase in Ge concentration. Thermal conductivity, estimated by the laser-flash method, was virtually independent of Ge concentration, maintaining an excellent value around 2.0 W cm⁻¹ K⁻¹. Thermal expansion coefficients along the a- and m-axes were approximately constant at 5.0×10⁻⁶ K⁻¹ in the measured doping concentration range.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.     

Electron microscopy analysis of dislocation behavior in HVPE-AlGaN layer grown on a stripe-patterned (0 0 0 1) sapphire substrate

Microstructures were investigated by transmission electron microscopy (TEM) and scanning electron microscopy (SEM) in order to clarify the dislocation behavior in AlGaN layers HVPE-grown on a stripe-patterned sapphire (0 0 0 1) substrate. SEM observation revealed very clearly the growth process: if AlGaN starting to grow from the side-wall of patterned substrate develops, a poly-crystalline region is formed up to the top surface of thin film. When the growth from the upper side (terrace) of patterned substrate is predominant, AlGaN becomes a single-crystalline layer with a flat surface. Threading dislocations (TDs) generated from the interface to the terrace propagate upwards, inclining to the wing regions. They are scarcely merged with one another. The AlGaN layer on the patterned substrate with a wider groove has a smaller density of dislocation to be about 1×10⁹ cm⁻². There are four types of dislocations: (1) TDs inclining toward 〈1 1¯ 0 0〉 normal to their Burgers vector B; (2) TDs inclining toward 〈2 1¯ 1¯ 0〉 on their slip-plane; (3) TDs inclining largely or horizontal dislocations (HDs) along 〈2 1¯ 1¯ 0〉 and (4) roundly curved HDs lying on (0 0 0 1) plane. Some TDs change the direction of inclination, suggesting that internal stress changed intricately during the growth.     

Structure and growth morphology of Gd2O3-doped CeO2 thin films

Gd₂O₃-doped CeO₂ (Gd_0.1Ce_0.9O_1.95, GDC) thin films were synthesized on (1 0 0) Si single crystal substrates by a reactive radio frequency magnetron sputtering technique. Structures and surface morphologies were characterized by X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and one-dimensional power spectral density (1DPSD) analysis. The XRD patterns indicated that, in the temperature range of 200–700 °C, f.c.c. structured GDC thin films were formed with growth orientations varying with temperature—random growth at 200 °C, (2 2 0) textures at 300–600 °C and (1 1 1) texture at 700 °C. GDC film synthesized at 200 °C had the smoothest surface with roughness of R_rms=0.973 nm. Its 1DPSD plot was characterized with a constant part at the low frequencies and a part at the high frequencies that could be fitted by the f^−2.4 power law decay. Such surface feature and scaling behavior were probably caused by the high deposition rate and random growth in the GDC film at this temperature. At higher temperatures (300–700 °C), however, an intermediate frequency slope (−γ₂≈−2) appeared in the 1DPSD plots between the low frequency constant part and the high frequency part fitted by f⁻⁴ power law decay, which indicated a roughing mechanism dominated by crystallographic orientation growth that caused much rougher surfaces in GDC films (R_rms>4 nm).     

Effect of NH3 flow rate on m-plane GaN growth on m-plane SiC by metalorganic chemical vapor deposition

This paper reports a study of the effect of NH₃ flow rate on m-plane GaN growth on m-plane SiC with an AlN buffer layer. It is found that a reduced NH₃ flow rate during m-plane GaN growth can greatly improve the recovery of in situ optical reflectance and the surface morphology, and narrow down the on-axis (1 0 1¯ 0) X-ray rocking curve (XRC) measured along the in-plane a-axis. The surface striation along the in-plane a-axis, a result of GaN island coalescence along the in-plane c-axis, strongly depends on the NH₃ flow rate, an observation consistent with our recent study of kinetic Wulff plots. The pronounced broadening of the (1 0 1¯ 0) XRC measured along the c-axis is attributed to the limited lateral coherence length of GaN domains along the c-axis, due to the presence of a high density of basal-plane stacking faults, most of which are formed at the GaN/AlN interface, according to transmission electron microscopy.     

Growth and Raman spectroscopic characterization of As4S4 (II) single crystals

As described by Kutoglu (1976 [16]), single crystals of As₄S₄ (II) phase have been grown using a new two-step synthesis that drastically increases the reproducibility that is attainable in synthetic experiments. First, through photo-induced phase transformation, pararealgar powder is prepared as a precursor instead of AsS melt. Then it is dissolved and recrystallized from CS₂ solvent. Results show that single crystals of the As₄S₄ (II) phase were obtained reproducibly through the dissolution–recrystallization process. Single crystals of As₄S₄ (II) obtained using this method were translucent and showed a uniform yellow-orange color. The crystal exhibits a platelet-like shape as a thin film with well-developed faces (0 1 0) and (0 1¯ 0). The grown crystals are as large as 0.50×0.50×0.01 mm. They were characterized using powder and single crystal X-ray diffraction techniques to confirm the phase identification and the lattice parameters. The As₄S₄ (II) phase crystallizes in monoclinic system with cell parameters a=11.202(4) Å, b=9.954(4) Å, c=7.142(4) Å, β=92.81(4)°, V=795.4(6) Å³, which shows good agreement with the former value. Raman spectroscopic studies elucidated the behavior of the substance and the relation among phases of tetra-arsenic tetrasulfide.     

A route to single-crystalline ZnO films with low residual electron concentration

Single-crystalline ZnO films have been grown on a-plane sapphire in plasma assisted molecular beam epitaxy by introducing a high-temperature ZnO buffer layer. The residual electron concentration of the films can be lowered to 1.5×10¹⁶ cm⁻³, comparable with the best value ever reported for ZnO films grown on a rare and costly substrate of ScAlMgO₄. A 3×3 reconstruction has been observed on the films grown in this route, which reveals that the films have very smooth surface. X-ray phi-scan spectrum of the films shows six peaks with 60° intervals, and two-dimensional X-ray diffraction datum indicates the single-crystalline nature of the films. Low temperature photoluminescence spectrum of the films shows a dominant free exciton emission and five phonon replicas, confirming the high quality of the films.     

Surface morphology,structural and optical properties of polar and non-polar ZnO thin films: A comparative study

The polar and non-polar ZnO thin films were fabricated on cubic MgO (1 1 1) and (0 0 1) substrates by plasma-assisted molecular beam epitaxy. Based on X-ray diffraction analysis, the ZnO thin films grown on MgO (1 1 1) and (1 0 0) substrates exhibit the polar c-plane and non-polar m-plane orientation, respectively. Comparing with the c-plane ZnO film, the non-polar m-plane ZnO film shows cross-hatched stripes-like morphology, lower surface roughness and slower growth rate. However, low-temperature photoluminescence measurement indicates the m-plane ZnO film has a stronger 3.31 eV emission, which is considered to be related to stacking faults. Meanwhile, stronger band tails absorbance of the m-plane ZnO film is observed in optical absorption spectrum.