首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
GaN films were grown by metal organic chemical vapor deposition on TaC substrates that were created by pulsed laser deposition of TaC onto (0 0 0 1) SiC substrates at ∼1000 °C. This was done to determine if good quality TaC films could be grown, and if good quality GaN films could be grown on this closely lattice matched to GaN, conductive material. This was done by depositing the TaC on on-axis and 3° or 8° off-axis (0 0 0 1) SiC at temperatures ranging from 950 to 1200 °C, and examining them using X-ray diffraction, scanning electron microscopy, atomic force microscopy, and transmission electron microscopy. The GaN films were grown on as-deposited TaC films, and films annealed at 1200, 1400, or 1600 °C, and examined using the same techniques. The TaC films were polycrystalline with a slight (1 1 1) texture, and the grains were ∼200 nm in diameter. Films grown on-axis were found to be of higher quality than those grown on off-axis substrates, but the latter could be improved to a comparable quality by annealing them at 1200–1600 °C for 30 min. TaC films deposited at temperatures above 1000 °C were found to react with the SiC. GaN films could be deposited onto the TaC when the surface was nitrided with NH3 for 3 min at 1100 °C and the low temperature buffer layer was AlN. However, the GaN did not nucleate easily on the TaC film, and the crystallites did not have the desired (0 0 0 1) preferred orientation. They were ∼10 times larger than those typically seen in films grown on SiC or sapphire. Also the etch pit concentration in the GaN films grown on the TaC was more than 2 orders of magnitude less than it was for growth on the SiC.  相似文献   

2.
The hydride-vapour-phase-epitaxial (HVPE) growth of semi-polar (1 1 2¯ 2)GaN is attempted on a GaN template layer grown on a patterned (1 1 3) Si substrate. It is found that the chemical reaction between the GaN grown layer and the Si substrate during the growth is suppressed substantially by lowering the growth temperatures no higher than 900 °C. And the surface morphology is improved by decreasing the V/III ratio. It is shown that a 230-μm-thick (1 1 2¯ 2)GaN with smooth surface is obtained at a growth temperature of 870 °C with V/III of 14.  相似文献   

3.
We have obtained single-crystal aluminum nitride (AlN) layers on diamond (1 1 1) substrates by metalorganic vapor-phase epitaxy (MOVPE). When the thermal cleaning temperature of the substrate and growth temperature of the AlN layer were below 1100 °C, the AlN layer had multi-domain structures mainly consisting of rotated domains. An interface layer, consisting of amorphous carbon and poly-crystal AlN, was formed between the AlN layer and the diamond substrate. On the other hand, when the thermal cleaning temperature and growth temperature were above 1200 °C, a single-crystal AlN layer was grown and no interface layer was formed. Therefore, we attribute the multi-domain structures to the interface layer. Even at the growth temperature of 1100 °C, by performing the thermal cleaning at 1200 °C, the single-crystal AlN layer was obtained, indicating that the thermal cleaning temperature of the substrate is a critical factor for the formation of the interface layer. The epitaxial relationship between the single-crystal AlN layer and the diamond (1 1 1) substrate was determined to be [0 0 0 1]AlN∥[1 1 1]diamond and [1 0 1¯ 0]AlN∥[1 1¯ 0]diamond. The AlN surface had Al polarity and no inversion domains were observed in the AlN layer.  相似文献   

4.
A crack-free aluminum nitride (AlN) template layer was grown on a (0 0 0 1) sapphire substrate at 1450 °C using a thin (100 nm) protective AlN layer grown at 1065 °C by hydride vapor-phase epitaxy (HVPE). Full-width at half-maximum (FWHM) values of X-ray rocking curves (XRCs) for (0 0 0 2) and (1 0 1¯ 0) planes of the AlN layer were 378 and 580 arcsec, respectively. The formation of voids was observed at the interface between the thin protective AlN layer and the sapphire substrate due to decomposition reaction of sapphire during heating up to 1450 °C. The voids relaxed the tensile stress in the AlN layer, which resulted in the suppression of cracks.  相似文献   

5.
Void formation at the interface between thick AlN layers and (0 0 0 1) sapphire substrates was investigated to form a predefined separation point of the thick AlN layers for the preparation of freestanding AlN substrates by hydride vapor phase epitaxy (HVPE). By heating 50–200 nm thick intermediate AlN layers above 1400 °C in a gas flow containing H2 and NH3, voids were formed beneath the AlN layers by the decomposition reaction of sapphire with hydrogen diffusing to the interface. The volume of the sapphire decomposed at the interface increased as the temperature and time of the heat treatment was increased and as the thickness of the AlN layer decreased. Thick AlN layers subsequently grown at 1450 °C after the formation of voids beneath the intermediate AlN layer with a thickness of 100 nm or above self-separated from the sapphire substrates during post-growth cooling with the aid of voids. The 79 μm thick freestanding AlN substrate obtained using a 200 nm thick intermediate AlN layer had a flat surface with no pits, high optical transparency at wavelengths above 208.1 nm, and a dislocation density of 1.5×108 cm−2.  相似文献   

6.
InN films have been successfully grown on sapphire substrates by MOVPE using trimethylindium (TMIn) and 1,1-dimethylhydrazine (DMHy) with N2 carrier. DMHy is an advantageous precursor of N as it decomposes efficiently at relatively low temperature (T50=420 °C) compatible with the InN growth. The reactor is specially designed so as to avoid parasitic reaction between TMIn and DMHy occurring at room temperature. The growth feature was studied by varying growth temperature, V/III ratio, TMIn flow and reactor pressure. The InN films were obtained at 500–570 °C and 60–200 Torr with a V/III ratio optimized to 100–200. The In droplets are seen on the grown surfaces, indicating an excess supply of TMIn. It is demonstrated that the InN films grows on the sapphire substrate in a single domain with an epitaxial relationship, [1 01¯ 0]InN//[1 1 2¯ 0]sapphire.  相似文献   

7.
A thick AlN layer was grown on a trench-patterned AlN/sapphire template by low-presssure hydride vapor phase epitaxy (LP-HVPE). Compared with the AlN layer grown on a flat AlN/sapphire template, the AlN layer grown on the trench-patterned AlN/sapphire template had a crack-free and smooth surface. The typical full-widths at half-maximum (FWHMs) of X-ray rocking curves (XRC) for the (0 0 0 2), (1 0 1¯ 2), and (1 0 1¯ 0) diffractions of the AlN layer on the trench-patterned AlN/sapphire template were 132, 489, and 594 arcsec, respectively. In addition, atomic steps were observed on the AlN layer on the trench-patterned AlN/sapphire template, and the root-mean-square (RMS) roughness of the AlN layer was determined to be 0.602 nm by atomic force microscopy (AFM).  相似文献   

8.
We fabricated one-dimensional GaN nanorods on AlN/Si (1 1 1) substrates at various temperatures, and carrier gas flow amount, using the hydride vapor phase epitaxy (HVPE) method. An AlN buffer layer of 50 nm thickness was deposited by RF sputtering for 25 min. Stalagmite-like GaN nanorods formed at a growth temperature of 650 °C. The diameters and lengths of GaN nanorods increase with growth time, whereas the density of nanorods decreases. And we performed the experiments by changing the carrier gas flow amount at a growth temperature of 650 °C and HCl:NH3 flow ratio of 1:40. GaN nanorods, with an average diameter of 50 nm, were obtained at a carrier gas flow amount of 1340 sccm. The shape, structures, and optical characteristics of the nanorods were investigated by field-emission scanning electron microscopy, X-ray diffraction, and photoluminescence.  相似文献   

9.
This study demonstrates a pure c-plane AlGaN epilayer grown on a γ-LiAlO2 (1 0 0) (LAO) substrate with an AlN nucleation layer grown at a relatively low temperature (LT-AlN) by metal-organic chemical vapor deposition (MOCVD). The AlGaN film forms polycrystalline film with m- and c-plane when the nucleation layer grows at a temperature ranging from 660 to 680 °C. However, a pure c-plane AlGaN film with an Al content of approximately 20% can be obtained by increasing the LT-AlN nucleation layer growth temperature to 700 °C. This is because the nuclei density of AlN increases as the growth temperature increases, and a higher nuclei density of AlN deposited on LAO substrate helps prevent the deposition of m-plane AlGaN. Therefore, high-quality and crack-free AlGaN films can be obtained with a (0 0 0 2) ω-rocking curve FWHM of 547 arcsec and surface roughness of 0.79 nm (root-mean-square) using a 700-°C-grown LT-AlN nucleation layer.  相似文献   

10.
Large and thick AlN bulk single crystals up to 43 mm in diameter and 10 mm in thickness have been successfully grown on 6H-SiC (0 0 0 1) substrates by the sublimation method using a TaC crucible. Raman spectrum indicates that the polytype of the grown AlN single crystals is a Wurtzite-2H type structure, and the crystals do not include any impurity phases. The quality at the top of the crystal improves as crystal thickness increases along the 〈0 0 0 1〉 direction during growth: a low etch pit density (7×104 cm−2) and a small full width at half maximum for a 0002 X-ray rocking curve (58 arcsec) have been achieved at a thickness of ∼8 mm. The possible mechanism behind the improvement in the AlN crystal quality is also discussed.  相似文献   

11.
AlGaN growth using epitaxial lateral overgrowth (ELO) by metalorganic chemical vapor deposition on striped Ti, evaporated GaN on sapphire, has been investigated. AlGaN/AlN films growth on GaN/AlGaN superlattices (SLs) structure on the Ti masks, with various SLs growth temperature (1030, 1060 and 1090 °C) were grown. With increasing the growth temperature, AlGaN surface became flat. The AlGaN film had a cathodoluminescence peak around 345 nm. However, in secondary ion mass spectrometry (SIMS) measurement, Ti signal was detected on the top of AlGaN surface when GaN/AlGaN SLs was grown on Ti striped masks. By inserting the AlN blocking layer on SLs, Ti diffusion was stopped at the AlN layer, and the AlGaN crystalline quality was improved.  相似文献   

12.
Non-polar (1 1 2¯ 0) a-plane GaN films have been grown by low-pressure metal-organic vapor deposition on r-plane (1 1¯ 0 2) sapphire substrate. We report on an approach of using AlN/AlGaN superlattices (SLs) for crystal quality improvement of a-plane GaN on r-plane sapphire. Using X-ray diffraction and atomic force microscopy measurements, we show that the insertion of AlN/AlGaN SLs improves crystal quality, reduces surface roughness effectively and eliminates triangular pits on the surface completely.  相似文献   

13.
To improve crystal quality of InN, an in-situ cyclic rapid pulse annealing during growth was carried out using infrared-lamp-heated molecular beam epitaxy. A cycle of 4 min growth of InN at 400 °C and 3 s pulse annealing at a higher temperature was repeated 15 times on AlN on Si substrate. Annealing temperatures were 550, 590, 620, and 660 °C. The back of Si was directly heated by lamp irradiation through a quartz rod. A total InN film thickness was about 200 nm. With increasing annealing temperature up to 620 °C, crystal grain size by scanning electron microscope showed a tendency to increase, while widths of X-ray diffraction rocking curve of (0 0 0 2) reflection and E2 (high) mode peak of Raman scattering spectra decreased. A peak of In (1 0 1) appeared in X-ray diffraction by annealing higher than 590 °C, and In droplets were found on the surface by annealing at 660 °C.  相似文献   

14.
We demonstrate hexagonal boron nitride (h-BN) epitaxial growth on Ni(1 1 1) substrate by molecular beam epitaxy (MBE) at 890 °C. Elemental boron evaporated by an electron-beam gun and active nitrogen generated by a radio-frequency (RF) plasma source were used as the group-III and -V sources, respectively. Reflection high-energy electron diffraction revealed a streaky (1×1) pattern, indicative of an atomically flat surface in the ongoing growth. Correspondingly, atomic force microscopy images exhibit atomically smooth surface of the resulting h-BN film. X-ray diffraction characterization confirmed the crystallinity of the epitaxial film to be h-BN, and its X-ray rocking curve has a full-width at half-maximum of 0.61°, which is the narrowest ever reported for h-BN thin film. The epitaxial alignments between the h-BN film and the Ni substrate were determined to be [0 0 0 1]h−BN∥[1 1 1]Ni, [1 1 2¯ 0]h−BN∥[1¯ 1 0]Ni, and [1 1¯ 0 0]h−BN∥[1¯ 1¯ 2]Ni.  相似文献   

15.
Indium nitride (InN) layers were grown on (1 1 1) silicon substrates by reactive magnetron sputtering using an indium target. Atomic force microscope, X-ray diffraction, and Raman spectroscopy analysis revealed that highly c-axis preferred wurtzite InN layers with very smooth surface can be obtained on (1 1 1) silicon substrates at a substrate temperature as low as 100 °C. The results indicate that the reactive sputtering is a promising growth technique for obtaining InN layers on silicon substrates at low substrate temperature with low cost and good compatibility with microelectronic silicon-based devices.  相似文献   

16.
We have obtained high-quality, crack-free AlN wafers using a convex thermal field inside the growth chamber. Free-standing AlN boules of 15 mm in height and 15 mm in diameter were grown. The carbon concentration was found to be similar in all parts of the boule (∼8×1018 cm−3) while the initial O concentration was higher (∼1×1019 cm−3) and slightly decreased during growth. It was found that O incorporated differently on different crystallographic faces. High resolution XRD showed a continuous improvement in crystal quality as a function of boule length. The full width at half maximum (FWHM) of the double crystal rocking curves decreased from 78 in at the beginning of growth to 13 in at the growth end. To the best of our knowledge, this is the first report on impurity incorporation on different crystallographic facets obtained from the same boule.  相似文献   

17.
Non-polar a-plane GaN film with crystalline quality and anisotropy improvement is grown by use of high temperature AlN/AlGaN buffer, which is directly deposited on r-plane sapphire by pulse flows. Compared to the a-plane GaN grown on AlN buffer, X-ray rocking curve analysis reveals a remarkable reduction in the full width at half maximum, both on-axis and off-axis. Atomic force microscopy image exhibits a fully coalesced pit-free surface morphology with low root-mean-square roughness (∼1.5 nm). Photoluminescence is carried out on the a-plane GaN grown on r-plane sapphire. It is found that, at low temperature, the dominant emission at ∼3.42 eV is composed of two separate peaks with different characteristics, which provide explanations for the controversial attributions of this peak in previous studies.  相似文献   

18.
A combination of experimental and computational fluid dynamics-based reactor modeling studies were utilized to study the effects of process conditions on GaN nanowire growth by metalorganic chemical vapor deposition (MOCVD) in an isothermal tube reactor. The GaN nanowires were synthesized on (0 0 0 1) sapphire substrates using nickel thin films as a catalyst. GaN nanowire growth was observed over a furnace temperature range of 800–900 °C at V/III ratios ranging from 33 to 67 and was found to be strongly dependent on the position of the substrate relative to the group III inlet tube. The modeling studies revealed that nanowire growth consistently occurred in a region in the reactor where the GaN thin-film deposition rate was reduced and the gas phase consisted primarily of intermediate species produced by the reaction and decomposition of trimethylgallium–ammonia adduct compounds. The GaN nanowires exhibited a predominant [1 1 2¯ 0] growth direction. Photoluminescence measurements revealed an increase in the GaN near-band edge emission intensity and a reduction in the deep-level yellow luminescence with increasing growth temperature and V/III ratio.  相似文献   

19.
Neodymium phosphate single crystals, NdPO4, have been grown by a flux growth method using Li2CO3-2MoO3 as a flux. The as-grown crystals were characterized by X-ray powder diffraction(XRPD), differential thermal analysis (DTA) and thermogravimetric analysis (TG) techniques. The results show that the as-grown crystals were well crystallized. The crystal was stable over the temperature range from 26 to 1200 °C in N2. The specific heat of NdPO4 crystal at room temperature was 0.41 J/g °C. The absorption and the fluorescence spectra of NdPO4 crystal were also measured at room temperature.  相似文献   

20.
Dichlorosilane (DCS), silane and trisilane have been investigated as Si precursors for low temperature (<700 °C) Si reduced pressure chemical vapor deposition. DCS and silane are limited to growth temperatures higher than 600–650 and 500 °C, respectively. At lower temperatures, absence of either Cl or H desorption from the surface impedes Si growth with acceptable growth rate (>5 Å/min). Trisilane permits the growth of Si at lower temperatures below 350 °C due to a specific growth mechanism enhancing H desorption. Layers grown at temperatures lower than 500 °C are defective, irrespective of the carrier gas, pressure and precursor flow used.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号