Growth and characterization of green GaInN-based light emitting diodes on free-standing non-polar GaN templates

We demonstrate homoepitaxial growth of GaInN/GaN-based green (500–560 nm) light emitting diodes (LEDs) on a-plane and m-plane quasi-bulk GaN prepared by hydride vapor phase epitaxy (HVPE). We find that in order to achieve an emission peak wavelength beyond 500 nm, a minimum InN-fraction of ∼14% is needed for both, a- and m-plane quantum wells (QWs), while ∼8% are enough for c-plane-oriented QWs. Besides increasing the InN-fraction in these non-polar QWs, widening the QW also proves to effectively shift the emission to longer wavelengths without loosing efficiency with the benefit of maintaining a low InN-fraction.     

Surface morphology,structural and optical properties of polar and non-polar ZnO thin films: A comparative study

The polar and non-polar ZnO thin films were fabricated on cubic MgO (1 1 1) and (0 0 1) substrates by plasma-assisted molecular beam epitaxy. Based on X-ray diffraction analysis, the ZnO thin films grown on MgO (1 1 1) and (1 0 0) substrates exhibit the polar c-plane and non-polar m-plane orientation, respectively. Comparing with the c-plane ZnO film, the non-polar m-plane ZnO film shows cross-hatched stripes-like morphology, lower surface roughness and slower growth rate. However, low-temperature photoluminescence measurement indicates the m-plane ZnO film has a stronger 3.31 eV emission, which is considered to be related to stacking faults. Meanwhile, stronger band tails absorbance of the m-plane ZnO film is observed in optical absorption spectrum.     

Spectrometric and ellipsometric studies of (1 − x)TiO2 · xLn2O3 (Ln = Nd, Sm, Gd, Er, Yb) thin films

Spectrometric and ellipsometric studies of (1 − x)TiO₂ · xLn₂O₃ (Ln = Nd, Sm, Gd, Er, Yb; x = 0.33, 0.5) thin films at room temperature were performed. The obtained dispersion dependences of refractive indices are successfully described by the optical-refractometric relation. The dependence of optical pseudogap and refractive indices on composition and molar mass of the films is investigated. The influence of compositional disordering on the energy width of the exponential absorption edge is studied.     

Influence of metal organic and inorganic precursors on spray pyrolyzed ceramic MgO (2 0 0) thin films for epitaxial over layers

The MgO (2 0 0) surface is widely used as a substrate for epitaxial growth of superconducting and ferro-electric films. Highly oriented, single crystalline, extremely flat and transparent MgO films have been successfully deposited on quartz substrates by the chemical spray pyrolysis technique using economically viable metal organic and inorganic precursors under optimized conditions at the substrate temperature of 600 °C. Thermal analysis (TGA/DTA) in the temperature range 30-600 °C with the heating rate of 10 °C/min revealed the decomposition behavior of the precursors and confirmed the suitable substrate temperature range for film processing. The heat of reaction, ΔH due to decomposition of metal organic precursor contributed additional heat energy to the substrate for better crystallization. The intensity of the (2 0 0) peak in X-ray diffraction (XRD) measurements and the smooth surface profiles revealed the dependency of precursor on film formation. The compositional purity and the metal-oxide bond formation were tested for all the films. UV-Vis-NIR optical absorption in the 200-1500 nm range revealed an optical transmittance above 80% and the absorption edge at about 238 nm corresponding to an optical band gap E_g = 5.25 eV. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) micrographs of MgO films confirmed better crystallinity with larger grain size (0.85 μm) and reduced surface roughness (26 nm), respectively.