Heteroepitaxial growth of InN layers on (1 1 1) silicon substrates

Indium nitride (InN) layers were grown on (1 1 1) silicon substrates by reactive magnetron sputtering using an indium target. Atomic force microscope, X-ray diffraction, and Raman spectroscopy analysis revealed that highly c-axis preferred wurtzite InN layers with very smooth surface can be obtained on (1 1 1) silicon substrates at a substrate temperature as low as 100 °C. The results indicate that the reactive sputtering is a promising growth technique for obtaining InN layers on silicon substrates at low substrate temperature with low cost and good compatibility with microelectronic silicon-based devices.     

HVPE growth of semi-polar (1 1 2¯ 2)GaN on GaN template (1 1 3)Si substrate

The hydride-vapour-phase-epitaxial (HVPE) growth of semi-polar (1 1 2¯ 2)GaN is attempted on a GaN template layer grown on a patterned (1 1 3) Si substrate. It is found that the chemical reaction between the GaN grown layer and the Si substrate during the growth is suppressed substantially by lowering the growth temperatures no higher than 900 °C. And the surface morphology is improved by decreasing the V/III ratio. It is shown that a 230-μm-thick (1 1 2¯ 2)GaN with smooth surface is obtained at a growth temperature of 870 °C with V/III of 14.     

Epitaxial NiO (1 0 0) and NiO (1 1 1) films grown by atomic layer deposition

Epitaxial NiO (1 1 1) and NiO (1 0 0) films have been grown by atomic layer deposition on both MgO (1 0 0) and α-Al₂O₃ (0 0 l) substrates at temperatures as low as 200 °C by using bis(2,2,6,6-tetramethyl-3,5-heptanedionato)Ni(II) and water as precursors. The films grown on the MgO (1 0 0) substrate show the expected cube on cube growth while the NiO (1 1 1) films grow with a twin rotated 180° on the α-Al₂O₃ (0 0 l) substrate surface. The films had columnar microstructures on both substrate types. The single grains were running throughout the whole film thickness and were significantly smaller in the direction parallel to the surface. Thin NiO (1 1 1) films can be grown with high crystal quality with a FWHM of 0.02–0.05° in the rocking curve measurements.     

Influence of substrate temperature on nitridation of (0 0 1) GaAs using RF-radical source

The mechanism of nitridation of (0 0 1) GaAs surface using RF-radical source was systematically studied with changing substrate temperature, nitridation time and supplying As molecular beam. It was found from atomic forth microscopy (AFM) measurements that supplying As is very important to suppress the re-evaporation of As atoms and to keep the surface smooth. Reflection high-energy electron diffraction (RHEED) measurements shows that surface lattice constant (SLC) of GaAs of 0.565 nm decreases with increasing the substrate temperature and that it finally relaxes to the value of c-GaN of 0.452 nm, at 570 °C in both [1 1 0] and [1¯ 1 0] directions without concerning with the supply of As molecular beam. But, in the medium temperature range (between 350 and 520 °C), SLC of [1 1 0] direction was smaller than that of [1¯ 1 0] direction. This suggests a relation between the surface structure and the relaxing mechanism of the lattice. The valence band discontinuity between the nitridated layer and the GaAs layer was estimated by using X-ray photoemission spectroscopy (XPS). It was between 1.7 and 2.0 eV, which coincides well with the reported value of c-GaN of 1.84 eV. This suggests that the fabricated GaN layer was in cubic structure.     

Epitaxial growth of tin oxide film on TiO2(1 1 0) using molecular beam epitaxy

Growth of tin oxide thin films using molecular beam epitaxy in a pyrolyzed nitrogen dioxide atmosphere on a titanium dioxide (1 1 0) substrate was investigated using X-ray photoelectron spectroscopy (XPS), electron diffraction, and atomic force microscopy (AFM). Properties of deposited films were studied for their dependence on substrate temperature and oxidation gas pressure. Analyses using XPS data revealed that tin atoms were fully oxidized to Sn⁴⁺ and SnO₂ films were grown epitaxially in deposition conditions of substrate temperatures of 627 K or higher and NO₂ pressure greater than 3×10⁻³ Pa. At a substrate temperature of 773 K, a smooth surface with atomic steps was visible in the SnO₂ films, but above or below this temperature, fine grains with crystal facets or porous structures appeared. At pressures of 8×10⁻⁴ to 3×10⁻⁴ Pa, the randomly oriented SnO phase was dominantly grown. Further decreasing the pressure, the Sn metal phase, which was epitaxially crystallized at less than 500 K, was also grown.     

Fabrication of (1 1 1)-oriented Si layers on SiO2 substrates by an aluminum-induced crystallization method and subsequent growth of semiconducting BaSi2 layers for photovoltaic application

We have prepared (1 1 1)-oriented Si layers on SiO₂ (fused silica) substrates from amorphous-Si(a-Si)/Al or Al/a-Si stacked layers using an aluminum-induced crystallization (AIC) method. The X-ray diffraction (XRD) intensity from the (1 1 1) planes of Si was found to depend significantly on growth conditions such as the thicknesses of Si and Al, deposition order (a-Si/Al or Al/a-Si on SiO₂), deposition technique (sputtering or vacuum evaporation) and exposure time of the Al layer to air before the deposition of Si. The crystal orientation of the Si layers was confirmed by θ−2θ, 2θ XRD and electron backscatter diffraction (EBSD). The photoresponse properties of semiconducting BaSi₂ films formed on the (1 1 1)-oriented Si layers by the AIC method were measured at room temperature. Photocurrents were clearly observed for photon energies greater than 1.25 eV. The external quantum efficiencies of the BaSi₂ were also evaluated.     

Characterizations of GaN films and AlGaN/GaN heterostructures on vicinal sapphire (0 0 0 1) substrates grown by MOCVD

GaN films and AlGaN/GaN heterostructures grown on vicinal sapphire (0 0 0 1) substrates by metalorganic chemical vapor deposition (MOCVD) are investigated. It is found that surface morphologies of GaN films depend on the vicinal angle, however, they are not sensitive to the inclination directions of the substrate. The optimized vicinal angle for obtaining excellent surface morphology is around 0.5°. This conclusion is also confirmed by characterizing the electrical property of two-dimensional electron gas (2DEG) in the AlGaN/GaN heterostructure.     

Influence of deposition conditions on nanocrystalline InN layers synthesized on Si(1 1 1) and GaN templates by RF sputtering

We present a detailed investigation on the influence of deposition conditions on morphological, structural and optical properties of InN films deposited on Si(1 1 1) and GaN-on-sapphire templates by reactive radio-frequency (RF) sputtering. The deposition parameters under study are nitrogen content in the sputtering gas, substrate–target distance, substrate temperature and RF power. X-ray diffraction measurements confirm the (0 0 0 1) preferred growth orientation and the wurtzite crystallographic structure of the material. For optimized deposition conditions, InN on Si(1 1 1) substrates presents smooth surface with root-mean-square roughness ∼1 nm. Surface quality of the InN films can be further improved by deposition on GaN-on-sapphire templates, achieving root-mean-square roughness as low as ∼0.4 nm, comparable to that of the underlying substrate. The room-temperature absorption edge is located at 1.70 eV. Intense low-temperature photoluminescence peaking at 1.60 eV is observed.     

Epitaxial growth of ZnO films on thin FeO(1 1 1) layers

Thin FeO(1 1 1) buffer layers prepared on Mo(1 1 0) substrate were used to grow ordered ZnO films under ultrahigh vacuum condition, and were in situ characterized by various surface analytical techniques. A chemical interaction between Zn (or ZnO) and FeO(1 1 1) can effectively lower the interfacial energy, which is in favor of an epitaxial growth of ZnO on FeO layers. Compared with the MgO(1 1 1) buffer layer used for the growth of ZnO(0 0 0 1) on sapphire (0 0 0 1) surface, the FeO(1 1 1) thin films might be a better one because it is more thermally stable. Our experimental results provide constructive information on the growth mechanism of ZnO-based materials, which is helpful for further understanding the growth mechanism of related oxide materials.     

MOVPE growth and properties of GaN on (1 1 1)Si using an AlInN intermediate layer

Using an AlInN intermediate layer, GaN was grown on (1 1 1)Si substrate by selective metalorganic vapor phase epitaxy. The variation of the surface morphology was investigated as a function of the In composition and thickness of the AlInN layer. It was found that the In composition in the AlInN layer was a function of the growth temperature and thickness. Because of the small band offset at the AlInN/Si hetero-interface, we have achieved a low series resistance of the order of 9 Ω (0.0036 Ω cm²) across the GaN/AlInN/AlN/Si layer structure.     

An ab initio-based approach to the stability of GaN(0 0 0 1) surfaces under Ga-rich conditions

Structural stability of GaN(0 0 0 1) under Ga-rich conditions is systematically investigated by using our ab initio-based approach. The surface phase diagram for GaN(0 0 0 1) including (2×2) and pseudo-(1×1) is obtained as functions of temperature and Ga beam equivalent pressure by comparing chemical potentials of Ga atom in the gas phase with that on the surface. The calculated results reveal that the pseudo-(1×1) appearing below 684–973 K changes its structure to the (2×2) with Ga adatom at higher temperatures beyond 767–1078 K via the newly found (1×1) with two adlayers of Ga. These results are consistent with the stable temperature range of both the pseudo-(1×1) and (2×2) with Ga adatom obtained experimentally. Furthermore, it should be noted that the structure with another coverage of Ga adatoms between the (1×1) and (2×2)-Ga does not appear as a stable structure of GaN(0 0 0 1). Furthermore, ghost island formation observed by scanning tunneling microscopy is discussed on the basis of the phase diagram.     

Growth of (1 0 1¯ 3¯ ) semipolar GaN on m-plane sapphire by hydride vapor phase epitaxy

The crystalline, surface, and optical properties of the (1 0 1¯ 3¯) semipolar GaN directly grown on m-plane sapphire substrates by hydride vapor phase epitaxy (HVPE) were investigated. It was found that the increase of V/III ratio led to high quality (1 0 1¯ 3¯) oriented GaN epilayers with a morphology that may have been produced by step-flow growth and with minor evidence of anisotropic crystalline structure. After etching in the mixed acids, the inclined pyramids dominated the GaN surface with a density of 2×10⁵ cm⁻², revealing the N-polarity characteristic. In the low-temperature PL spectra, weak BSF-related emission at 3.44 eV could be observed as a shoulder of donor-bound exciton lines for the epilayer at high V/III ratio, which was indicative of obvious reduction of BSFs density. In comparison with other defect related emissions, a different quenching behavior was found for the 3.29 eV emission, characterized by the temperature-dependent PL measurement.     

Influence of metal organic and inorganic precursors on spray pyrolyzed ceramic MgO (2 0 0) thin films for epitaxial over layers

The MgO (2 0 0) surface is widely used as a substrate for epitaxial growth of superconducting and ferro-electric films. Highly oriented, single crystalline, extremely flat and transparent MgO films have been successfully deposited on quartz substrates by the chemical spray pyrolysis technique using economically viable metal organic and inorganic precursors under optimized conditions at the substrate temperature of 600 °C. Thermal analysis (TGA/DTA) in the temperature range 30-600 °C with the heating rate of 10 °C/min revealed the decomposition behavior of the precursors and confirmed the suitable substrate temperature range for film processing. The heat of reaction, ΔH due to decomposition of metal organic precursor contributed additional heat energy to the substrate for better crystallization. The intensity of the (2 0 0) peak in X-ray diffraction (XRD) measurements and the smooth surface profiles revealed the dependency of precursor on film formation. The compositional purity and the metal-oxide bond formation were tested for all the films. UV-Vis-NIR optical absorption in the 200-1500 nm range revealed an optical transmittance above 80% and the absorption edge at about 238 nm corresponding to an optical band gap E_g = 5.25 eV. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) micrographs of MgO films confirmed better crystallinity with larger grain size (0.85 μm) and reduced surface roughness (26 nm), respectively.     

Growth of GaN based structures on Si(1 1 0) by molecular beam epitaxy

The growth of GaN based structures on Si(1 1 0) substrates by molecular beam epitaxy using ammonia as the nitrogen precursor is reported. The structural, optical and electrical properties of such structures are assessed and are quite similar to the ones obtained on Si(1 1 1) in-spite of the very different substrate surface symmetry. A threading dislocation density of 3.7×10⁹ cm⁻² is evaluated by transmission electron microscopy, which is in the low range of typical densities obtained on up to 2 μm thick GaN structures grown on Si(1 1 1). To assess the potential of such structure for device realization, AlGaN/GaN high electron mobility transistor and InGaN/GaN light emitting diode heterostructures were grown and their properties are compared with the ones obtained on Si(1 1 1).     

The effects of annealing on non-polar (1 1 2¯ 0) a-plane GaN films

Non-polar a-plane (1 1 2¯ 0) GaN films were grown on r-plane sapphire by metal–organic vapor phase epitaxy and were subsequently annealed for 90 min at 1070 °C. Most dislocations were partial dislocations, which terminated basal plane stacking faults. Prior to annealing, these dislocations were randomly distributed. After annealing, these dislocations moved into arrays oriented along the [0 0 0 1] direction and aligned perpendicular to the film–substrate interface throughout their length, although the total dislocation density remained unchanged. These changes were accompanied by broadening of the symmetric X-ray diffraction 1 1 2¯ 0 ω-scan widths. The mechanism of movement was identified as dislocation glide, occurring due to highly anisotropic stresses (confirmed by X-ray diffraction lattice parameter measurements) and evidenced by macroscopic slip bands observed on the sample surface. There was also an increase in the density of unintentionally n-type doped electrically conductive inclined features present at the film–substrate interface (as observed in cross-section using scanning capacitance microscopy), suggesting out-diffusion of impurities from the substrate along with prismatic stacking faults. These data suggest that annealing processes performed close to film growth temperatures can affect both the microstructure and the electrical properties of non-polar GaN films.     

The influence of the Al pre-deposition on the properties of AlN buffer layer and GaN layer grown on Si (1 1 1) substrate

The influence of Al pre-deposition on the properties of AlN buffer layer and GaN layer grown on Si (1 1 1) substrate by metalorganic chemical vapor deposition (MOCVD) has been systematically studied. Compared with the sample without Al pre-deposition, optimum Al pre-deposition time could improve the AlN buffer layer crystal quality and reduce the root mean square (RMS) roughness. Whereas, overlong Al-deposition time deteriorated the AlN crystal quality and Al-deposition patterns could be found. Cracks and melt-back etching patterns appeared in the GaN layer grown without Al pre-deposition. With suitable Al-deposition time, crack-free 2.0 μm GaN was obtained and the full-width at half-maximum (FWHM) of (0 0 2) plane measured by double crystal X-ray diffraction (DCXRD) was as low as 482 arcsec. However, overlong Al-deposition time would result in a great deal of cracks, and the crystal quality of GaN layer deteriorated. The surface of GaN layer became rough in the region where the Al-deposition patterns were formed due to overlong Al-deposition time.     

Theoretical investigation on the decomposition process of GaN(0 0 0 1) surface under a hydrogen atmosphere

The activation energies for Ga and N desorption from a GaN surface were calculated using the density functional theory to understand the detailed decomposition process of the hydrogen terminated GaN(0 0 0 1) Ga and N surfaces under a hydrogen atmosphere. It was found that the Ga atoms on the hydrogen terminated GaN(0 0 0 1) Ga surface desorbed as GaH molecules from the surface while the N atoms on the hydrogen terminated GaN(0 0 0 1) N surface desorbed as NH₃ molecules from the surface. The desorption energies of GaH and NH₃ on the hydrogen terminated surface were more consistent with the previous experimental values than those on the ideal surface. These results suggest that the initial surface structure of the GaN(0 0 0 1) surface is terminated with hydrogen.     

Influence of growth temperature on the selective area MOVPE of InAs nanowires on GaAs (1 1 1) B using N2 carrier gas

The influence of temperature on selective area (SA) InAs nanowire growth was investigated for metal-organic vapor phase epitaxy (MOVPE) using N₂ as the carrier gas and (1 1 1) B GaAs substrates. In contrast to the growth temperature range – below 600 °C – reported for hydrogen ambient, the optimal growth temperature between 650 and 700 °C was 100 K higher than the optimal ones for H₂ carrier gas. At these temperatures, nanowires with aspect ratios of about 80 and a symmetric hexagonal shape were obtained. The results found are attributed to the physical and chemical properties of the carrier gas.     

Formation of GaN nanodots on Si (1 1 1) by droplet nitridation

GaN nanodots (NDs) are obtained by Ga metallic droplet formation on Si (1 1 1) substrates followed by their nitridation. The size and density of Ga droplets and GaN NDs can be controlled by varying the growth temperature within the range 514–640 °C. Atomic force microscopy (AFM) investigation of Ga droplets shows an increase in the average diameter with temperature. The average diameter of GaN NDs increases with growth temperature while their density decreases more than one order of magnitude. In addition, the formation of a GaN crystallite rough layer on Si, in-between NDs, indicates that a spreading mechanism takes place during the nitridation process. High-resolution transmission electron microscopy (HRTEM) is used for the investigation of shape, crystalline quality and surface distribution of GaN dots. X-ray photoelectron spectroscopy (XPS) results confirm that Ga droplets that are transformed into GaN NDs spread over the sample surface during nitridation.     

Atomic ordering in GaAsSb (0 0 1) grown by metalorganic vapor phase epitaxy

Epitaxial GaAsSb (0 0 1) semiconductor alloys grown by metalorganic vapor phase epitaxy exhibit several spontaneously ordered structures. A superlattice structure with three-fold ordering in the [1 1 0] direction has been previously observed by different groups. CuAu structures with (1 0 0) and (0 1 0) ordering planes have also been reported. The physical origin of CuAu ordering in III–V semiconductors has not yet been explained. In this work we report the effect of growth conditions on CuAu ordering in GaAsSb, including miscut from (0 0 1), growth rate, bismuth surfactant concentration, and growth temperature. These data point to a surface kinetic mechanism not based on dimer strain, but possibly due to one-dimensional ordering at step edges.