Electrochemical Cholesterol Sensor Based on Tin Oxide‐Chitosan Nanobiocomposite Film

A chitosan (CS)‐tin oxide (SnO₂) nanobiocomposite film has been deposited onto an indium‐tin‐oxide glass plate to immobilize cholesterol oxidase (ChOx) for cholesterol detection. The value of the Michaelis–Menten constant (K_m) obtained as 3.8 mM for ChOx/CS‐SnO₂/ITO is lower (8 mM) than that of a ChOx/CS/ITO bioelectrode revealing enhancement in affinity and/or activity of ChOx towards cholesterol and also revealing strong binding of ChOx onto CS‐SnO₂/ITO electrode. This ChOx/CS‐SnO₂/ITO cholesterol sensor retains 95% of enzyme activity after 4–6 weeks at 4 °C with response time of 5 s, sensitivity of 34.7 μA/mg dL^?1 cm² and detection limit of 5 mg/dL.     

Direct Electrochemistry of Cholesterol Oxidase Immobilized on a Conducting Polymer: Application for a Cholesterol Biosensor

Direct electrochemistry of cholesterol oxidase (ChOx) immobilized on the conductive poly‐3′,4′‐diamine‐2,2′,5′,2″‐terthiophene (PDATT) was achieved and used to create a cholesterol biosensor. A well‐defined redox peak was observed, corresponding to the direct electron transfer of the FAD/FADH₂ of ChOx, and the rate constant (k_s) was determined to be 0.75 s^?1. Glutathione (GSH) covalently bonded with PDATT was used as a matrix for conjugating AuNPs, ChOx, and MP, simultaneously. MP co‐immobilized with ChOx on the AuNPs‐GSH/PDATT exhibited an excellent amperometric response to cholesterol. The dynamic range was from 10 to 130 μM with a detection limit of 0.3±0.04 μM.     

Amperometric Biosensor Based on Enzymatic Reactor for Choline Determination in Flow Systems

A simple, selective and stable biosensor with the enzymatic reactor based on choline oxidase (ChOx) was developed and applied for the determination of choline (Ch) in flow injection analysis with amperometric detection. The enzyme ChOx was covalently immobilized with glutaraldehyde to mesoporous silica powder (SBA‐15) previously covered by NH₂‐groups. This powder was found as an optimal filling of the reactor. The detection of Ch is based on amperometric monitoring of consumed oxygen during the enzymatic reaction, which is directly proportional to Ch concentration. Two arrangements of an electrolytic cell in FIA, namely wall‐jet cell with working silver solid amalgam electrode covered by mercury film and flow‐through cell with tubular detector of polished silver solid amalgam were compared. The experimental parameters affecting the sensitivity and stability of the biosensor (i. e. pH of the carrier solution, volume of reactor, amount of the immobilized enzyme, the detection potential, flow rate, etc.) were optimized. Under the optimized conditions, the limit of detection was found to be 9.0×10^?6 mol L^?1. The Michaelis‐Menten constant for covalently immobilized ChOx on SBA‐15 was calculated. The proposed amperometric biosensor with the developed ChOx‐based reactor exhibits good repeatability, reproducibility, long‐term stability, and reusability. Its efficiency has been confirmed by the successful application for the determination of Ch in two commercial pharmaceuticals.     

Study on the thermodynamic properties of cholesterol

The standard molar enthalpy of combustion of cholesterol was measured at constant volume. According to value of Δ_r U _m^θ(−14358.4±20.65 kJ mol⁻¹), Δ_r H _m^θ(−14385.7 kJ mol⁻¹) of combustion reaction and Δ_f H _m^θ(2812.9 kJ mol⁻¹) of cholesterol were obtained from the reaction equation. The enthalpy of combustion reaction of cholesterol was also estimated by the average bond enthalpies. By design of a thermo-chemical recycle, the enthalpy of combustion of cholesterol were calculated between 283.15∼373.15 K. Besides, molar enthalpy and entropy of fusion of cholesterol was obtained by DSC technique.     

Fabrication of a Sensitive Cholesterol Biosensor Based on Cobalt‐oxide Nanostructures Electrodeposited onto Glassy Carbon Electrode

Electrodeposited cobalt oxide (CoOx) nanomaterials are not only used for immobilization of cholesterol oxidase (ChOx) but also as electron transfer mediator for oxidation of H₂O₂ generated in the enzymatic reaction. Voltammetry and flow injection analysis (FIA) were used for determination of cholesterol. FIA determination of cholesterol with biosensors yielded a calibration curve with the following characteristics: linear range up to 50 μM, sensitivity of 43.5 nA μM^?1 cm^?2 and detection limit of 4.2 μM. The apparent Michaelis‐Menten constant and the response time of the biosensor are 0.49 mM and 15 s, respectively. This biosensor also exhibits good stability, reproducibility and long life time.     

Zinc oxide nanoparticles-chitosan composite film for cholesterol biosensor

Zinc oxide nanoparticles (NanoZnO) uniformly dispersed in chitosan (CHIT) have been used to fabricate a hybrid nanocomposite film onto indium-tin-oxide (ITO) glass plate. Cholesterol oxidase (ChOx) has been immobilized onto this NanoZnO-CHIT composite film using physiosorption technique. Both NanoZnO-CHIT/ITO electrode and ChOx/NanoZnO-CHIT/ITO bioelectrode have been characterized using Fourier transform-infrared (FTIR), X-ray diffraction (XRD), cyclic voltammetry (CV), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS) techniques, respectively. The ChOx/NanoZnO-CHIT/ITO bioelectrode exhibits linearity from 5 to 300 mg dl⁻¹ of cholesterol with detection limit as 5 mg dl⁻¹, sensitivity as 1.41 × 10⁻⁴ A mg dl⁻¹ and the value of Michaelis-Menten constant (K_m) as 8.63 mg dl⁻¹. This cholesterol biosensor can be used to estimate cholesterol in serum samples.     

A novel paper-based device coupled with a silver nanoparticle-modified boron-doped diamond electrode for cholesterol detection

A novel paper-based analytical device (PAD) coupled with a silver nanoparticle-modified boron-doped diamond (AgNP/BDD) electrode was first developed as a cholesterol sensor. The AgNP/BDD electrode was used as working electrode after modification by AgNPs using an electrodeposition method. Wax printing was used to define the hydrophilic and hydrophobic areas on filter paper, and then counter and reference electrodes were fabricated on the hydrophilic area by screen-printing in house. For the amperometric detection, cholesterol and cholesterol oxidase (ChOx) were directly drop-cast onto the hydrophilic area, and H₂O₂ produced from the enzymatic reaction was monitored. The fabricated device demonstrated a good linearity (0.39 mg dL⁻¹ to 270.69 mg dL⁻¹), low detection limit (0.25 mg dL⁻¹), and high sensitivity (49.61 μA mM⁻¹ cm⁻²). The precision value for ten replicates was 3.76% RSD for 1 mM H₂O₂. In addition, this biosensor exhibited very high selectivity for cholesterol detection and excellent recoveries for bovine serum analysis (in the range of 99.6–100.8%). The results showed that this new sensing platform will be an alternative tool for cholesterol detection in routine diagnosis and offers the advantages of low sample/reagent consumption, low cost, portability, and short analysis time.     

Nanostructured Iron Oxide Platform for Impedimetric Cholesterol Detection

A nanostructured iron oxide (NanoFe₃O₄, particle size ca. 25 nm and roughness ca. 21 nm) film deposited onto a hydrolyzed indium‐tin‐oxide (ITO) coated glass plate has been used to immobilize cholesterol oxidase (ChOx) to fabricate an impedimetric cholesterol sensor. Electrochemical studies reveal that surface charged Fe₃O₄ nanoparticles provide better conformation for ChOx loading resulting in enhanced electron transfer between ChOx and the electrode. Impedimetric response studies of the ChOx/NanoFe₃O₄/ITO bioelectrode exhibit improved linearity (2.5–400 mg/dL), low detection limit (0.25 mg/dL), fast response time (25 s), high sensitivity (86 Ω/mg dL^?1/cm^?2) and a low value of the Michaelis‐Menten constant (K_m, 0.8 mg/dL) with a regression coefficient of 0.997.     

Hemin Functionalized Multiwalled Carbon Nanotubes as a Matrix for Sensitive Electrogenerated Chemiluminescence Cholesterol Biosensor

Based on hemin‐MWCNTs nanocomposite and hemin‐catalyzed luminol‐H₂O₂ reaction, a sensitive electrogenerated chemiluminescence (ECL) cholesterol biosensor was proposed in this paper. Firstly, hemin‐MWCNTs was prepared via π–π stacking and modified on the surface of GCE. Subsequently, cholesterol oxidase (ChOx) was adsorbed on the modified electrode to achieve a cholesterol biosensor. Hemin‐MWCNTs nanocomposite provided the electrode with a large surface area to load ChOx, and endowed the nanostructured interface on the electrode surface to enhance the performance of biosensor. The biosensor responded to cholesterol in the linear range from 0.3 µM to 1.2 mM with a detection limit of 0.1 µM (S/N=3).     

Electrochemical Study of Chitosan‐SiO2‐MWNT Composite Electrodes for the Fabrication of Cholesterol Biosensors

We report a novel composite electrode made of chitosan‐SiO₂‐multiwall carbon nanotube (CHIT‐SiO₂‐MWNT) composite coated on the indium‐tin oxide (ITO) glass substrate. Cholesterol oxidase (ChOx) was covalently immobilized on the CHIT‐SiO₂‐MWNT/ITO electrode that resulted in a ChOx/CHIT‐SiO₂‐MWNT/ITO cholesterolactive bioelectrode. The CHIT‐SiO₂‐MWNT/ITO and ChOx/CHIT‐SiO₂‐MWNT/ITO electrodes were characterized with Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The influence of various parameters was investigated, including the applied potential, pH of the medium, and the concentration of the enzyme on the performance of the biosensor. The cholesterol bioelectrode exhibited a sensitivity of 3.4 nA/ mgdL^?1 with a response time of five seconds. The biosensor using ChOx/CHIT‐SiO₂‐MWNT/ITO as the working electrode retained its original response after being stored for six months. The biosensor using ChOx/CHIT‐SiO₂‐MWNT/ITO as the working electrode showed a linear current response to the cholesterol concentration in the range of 50–650 mg/dL.     

Silk Mat as Bio-matrix for the Immobilization of Cholesterol Oxidase

Cholesterol oxidase (ChOx) was covalently immobilized onto the woven silk fiber (silk mat) produced by Antheraea assamensis. The immobilization was done using N-ethyl-N’-(3-dimethylaminopropyl) carbodimide and N-hydroxysuccinimide ligand chemistry. The attachment of ChOx to the silk mat was demonstrated by scanning electron microscopy and activity study. The kinetic studies of the immobilized ChOx were performed by using a biological oxygen monitor. The enzyme loading was found to be 0.046 U cm^?2 of silk mat and the enzyme loading efficiency of the silk mat was estimated to be 70%. Remarkably high storage and operational stability (t_1/2 of initial activities) corresponding to 13 months and 25 numbers of assay (for a period of 6 h), respectively, of the fabricated ChOx electrode were demonstrated.     

Determination of enzyme activity inhibition by FTIR spectroscopy on the example of fructose bisphosphatase

A mid-infrared enzymatic assay for label-free monitoring of the enzymatic reaction of fructose-1,6-bisphosphatase with fructose 1,6-bisphosphate has been proposed. The whole procedure was done in an automated way operating in the stopped flow mode by incorporating a temperature-controlled flow cell in a sequential injection manifold. Fourier transform infrared difference spectra were evaluated for kinetic parameters, like the Michaelis–Menten constant (K _M) of the enzyme and V _max of the reaction. The obtained K _M of the reaction was 14 ± 3 g L⁻¹ (41 μM). Furthermore, inhibition by adenosine 5′-monophosphate (AMP) was evaluated, and the K _M^App value was determined to be 12 ± 2 g L⁻¹ (35 μM) for 7.5 and 15 μM AMP, respectively, with V _max decreasing from 0.1 ± 0.03 to 0.05 ± 0.01 g L⁻¹ min⁻¹. Therefore, AMP exerted a non-competitive inhibition.     

A Single Drop Fabrication of the Cholesterol Biosensor Based on Synthesized NiFe2O4NPs Dispersed on PDDA‐CNTs

A cholesterol biosensor based on cholesterol oxidase‐poly(diallyldimethylammonium chloride)‐carbon nanotubes‐nickel ferrite nanoparticles (ChOx‐PDDA‐CNTs‐NiFe₂O₄NPs) solution is easily fabricated by using a single dropping step on a glassy carbon electrode (GCE) surface. This technique is an alternative way to reduce complexity, cost and time to produce the biosensor. The uniformly dispersed materials on the electrode surface enhance the catalytic reaction of cholesterol oxidase and electron transfer from the oxidation of hydrogen peroxide in the system. The nickel ferrite nanoparticles were synthesized by co‐precipitation and calcination at various temperatures. These nanoparticles were then characterized using field emission scanning electron microscopy (FE‐SEM), energy‐dispersive X‐ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR), cyclic voltammetry (CV) and X‐ray diffraction (XRD). The synthesized material calcined at 700 °C was well defined and presented the octahedral metal stretching with cubic NiFe₂O₄NPs phase. In cyclic voltammetric study, the ChOx‐PDDA‐CNTs‐NiFe₂O₄NPs/GCE showed 0.43 s⁻¹ charge transfer rate constant (K _s), 7.79×10⁻⁶ cm² s⁻¹ diffusion coefficient value (D ), 0.13 mm² electroactive surface area (A _e) and 3.58×10⁻⁸ mol cm⁻² surface concentration ( ). This modified electrode exhibits stability in term of percent relative standard deviation (%RSD=0.62 %, n=10), reproducibility (%RSD=0.81, n=10), high sensitivity (25.76 nA per mg L⁻¹ cm⁻²), linearity from 1 to 5,000 mg L⁻¹ (R²=0.998) with a low detection limit (0.50 mg L⁻¹). Its Michaelis‐Menten constant (K _m) was 0.14 mM with 0.92 μA maximum current (I _max) and demonstrated good selectivity without the effects of electroactive species such as ascorbic acid, glucose and uric acid. The cholesterol biosensor was successfully applied to determine cholesterol levels in human blood samples, showing promise due to its simplicity and availability.     

Amperometric cholesterol biosensor based on immobilized cholesterol esterase and cholesterol oxidase on conducting polypyrrole films

Fabrication of an amperometric cholesterol biosensor by co-immobilization of cholesterol esterase (ChEt) and cholesterol oxidase (ChOx) onto conducting polypyrrole (PPY) films using electrochemical entrapment technique is described. Electrochemical polymerization was carried out using a two-electrode cell configuration at 0.8 V. Characterization of resulting amperometric biosensor for the estimation of cholesterol has been experimentally determined in terms of linear response range, optimum pH, applied potential, temperature, and shelf-life. These PPY/ChEt/ChOx electrodes can be used for cholesterol ester estimation from 1 to 8 mM and have shelf-life of about 4 weeks at 4 °C during which about 15 estimations of cholesterol ester could be made. The sensitivity of PPY/ChEt/ChOx electrode has been found to be 0.15 μA/mM and the apparent K_m value for this electrode is 9.8 mM. Conductivity of the polymer films found to be about 3×10⁻³ S/cm.     

Biosensor for total cholesterol estimation using N-(2-aminoethyl)-3-aminopropyltrimethoxysilane self-assembled monolayer

Cholesterol oxidase (ChOx), cholesterol esterase (ChEt), and horseradish peroxidase (HRP) have been co-immobilized covalently on a self-assembled monolayer (SAM) of N-(2-aminoethyl)-3-aminopropyltrimethoxysilane (AEAPTS) deposited on an indium–tin–oxide (ITO) glass surface. These enzyme-modified (ChOx-ChEt-HRP/AEAPTS/ITO) biosensing electrodes have been used to estimate cholesteryl oleate from 10 to 500 mg dL⁻¹. The sensitivity, K _m value, and shelf-life of these ChEt-ChOx-HRP/AEAPTS/ITO biosensing electrodes have been found to be 124 nA mg⁻¹ dL, 95.098 mg dL⁻¹ (1.46 mmol L⁻¹), and ten weeks, respectively. The ChEt-ChOx-HRP/AEAPTS/ITO bio-electrodes have been used to estimate total cholesterol in serum samples. Figure Covalent immobilization of enzymes onto AEAPTS/ITO surface using EDC/NHS chemistry Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Polypyrrole/multiwalled carbon nanotubes‐based biosensor for cholesterol estimation

The nanocomposite electrode comprising of polypyrrole (PPY) and carboxy functionalized multiwalled carbon nanotubes (MWCNT) has been electrochemically fabricated onto indium–tin–oxide (ITO) electrode using p‐toluene sulfonic acid (PTS). Cholesterol oxidase (ChOx) and cholesterol esterase (ChEt) have been immobilized onto this PPY– MWCNT/ITO nanocomposite electrode using N‐ethyl‐N‐(3‐dimethylaminopropyl) carbodiimide and N‐hydroxy succinimide chemistry for estimation of esterified cholesterol. The ChEt–ChOx/PPY–MWCNT/PTS/ITO bioelectrode has been characterized using Fourier transform infrared spectroscopy, electrochemical techniques, and scanning electron microscope. This ChEt–ChOx/PPY–MWCNT/PTS/ITO nanobioelectrode has a response time of about 9 s, linearity of 4 × 10^?4 to 6.5 × 10^?3 M/l of cholesterol oleate concentration, K_m of 0.02 mM, and thermal stability of upto 45°C. This electrode exhibits improved biosensing characteristics compared with other total cholesterol electrodes reported in literature till date and can be used to estimate cholesterol in blood serum samples. Copyright © 2011 John Wiley & Sons, Ltd.     

Poly(pyrrole) versus poly(3,4-ethylenedioxythiophene): amperometric cholesterol biosensor matrices

Two conducting polymers, poly(pyrrole) (PPy) and poly(3,4-ethylenedioxythiophene) (PEDOT) were used as immobilization matrices for cholesterol oxidase (ChOx). The amperometric responses of the enzyme electrodes were measured by monitoring oxidation current of H₂O₂ at +0.7 V in the absence of a mediator. Kinetic parameters, such as K _m and I _max, operational and storage stabilities, effects of pH and temperature were determined for both entrapment supports. K _m values are found as 7.9 and 1.3 mM for PPy and PEDOT enzyme electrodes, respectively; it can be interpreted that ChOx immobilized in PEDOT shows higher affinity towards the substrate.     

Sol–gel derived nanoporous cerium oxide film for application to cholesterol biosensor

Cholesterol oxidase (ChOx) has been immobilized onto sol–gel derived nano-structured cerium oxide (NS-CeO₂) film deposited on indium-tin-oxide (ITO) coated glass substrate. Phase identification of sol–gel NS-CeO₂ film carried out using X-ray diffraction (XRD) yields reflection peak at 29.4° corresponding to (1 1 1) plane with oriented crystallite (34 nm) along c-axis normal to the substrate. Electrochemical studies reveal that NS-CeO₂ provides electroactive surface for the loading of ChOx and enhances electron transfer rate in the ChOx/NS-CeO₂/ITO bioelectrode. The low value of Michaelis–Menten constant (K_m) obtained as 2.08 mM indicates enhanced ChOx affinity to cholesterol. The observed results show application of sol–gel derived NS-CeO₂ for biosensing without any functionalization.     

Langmuir-Blodgett film based on MEH-PPV for cholesterol biosensor

Cholesterol oxidase (ChOx) has been immobilized onto conducting poly[2-methoxy,5-(2′-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV)/stearic acid (SA) Langmuir-Blodgett film transferred onto octadecanethiol (ODT) modified gold plate. The ChOx/MEH-PPV/SA LB film bioelectrode exhibits has been characterized by FT-IR, contact angle, and atomic force microscopy. The response of the ChOx/MEH-PPV/SA LB film bioelectrode carried out using differential pulse voltammetry (DPV) studies reveal linearity from 1.29 to 12.91 mM of cholesterol concentration and response time as 30 s. This ChOx/MEH-PPV/SA bioelectrode exhibits values of correlation coefficient as 0.9939, standard deviation as 0.0029 μA and limit of detection as 1.66 mM. UV-visible spectrophotometer studies reveal that 5.2 × 10⁻³ U of ChOx are actively working per cm² area of ChOx/MEH-PPV/SA LB film bioelectrode and this bioelectrode is thermally stable upto 55 °C with reusability of about 60 times.     

Carbon Nanotubes‐Based Amperometric Cholesterol Biosensor Fabricated Through Layer‐by‐Layer Technique

A carbon nanotubes‐based amperometric cholesterol biosensor has been fabricated through layer‐by‐layer (LBL) deposition of a cationic polyelectrolyte (PDDA, poly(diallyldimethylammonium chloride)) and cholesterol oxidase (ChOx) on multi‐walled carbon nanotubes (MWNTs)‐modified gold electrode, followed by electrochemical generation of a nonconducting poly(o‐phenylenediamine) (PPD) film as the protective coating. Electrochemical impedance measurements have shown that PDDA/ChOx multilayer film could be formed uniformly on MWNTs‐modified gold electrode. Due to the strong electrocatalytic properties of MWNTs toward H₂O₂ and the low permeability of PPD film for electroacitve species, such as ascorbic acid, uric acid and acetaminophen, the biosensor has shown high sensitivity and good anti‐interferent ability in the detection of cholesterol. The effect of the pH value of the detection solution on the response of the biosensor was also investigated. A linear range up to 6.0 mM has been observed for the biosensor with a detection limit of 0.2 mM. The apparent Michaelis‐Menten constant and the maximum response current density were calculated to be 7.17 mM and 7.32 μA cm^?2, respectively.