Highly sensitive semi-quantitative field test for the determination of chromium (VI) in aqueous samples

A method for the semi-quantitative colorimetric determination of chromium(VI) at sub μg/L levels after sorptive preconcentration is presented. The method is based on the retention of the reaction product (preformed in liquid phase) between Cr(VI) and diphenylcarbazide on membrane embedded cation exchange material. The color intensity of the membrane can be correlated to Cr(VI) concentrations in the range 0.05–50 μg/L (i.e. almost three orders of magnitude lower than the conventional spectrophotometric procedure) with a detection limit of about 10 ng/L (using 50 mL of sample volume). Due to the visual inspection mode and comparative color detection the precision is only 30–80% rsd which, however, is regarded as sufficient for screening purposes. Analysis of real samples including different kinds of waters and extracts of soil and filter collected airborne particulate matter demonstrated the applicability of the method for fast and species selective screening. Recovery experiments generally gave reasonably good results, yet also revealed the risk of the conversion of chromium species during sample pretreatment procedures due to redox reactions.     

Highly sensitive adsorptive stripping voltammetric method for the ultra-trace determination of chromium(VI).

A rapid differential pulse adsorptive stripping voltammetric method has been developed for the ultra-trace determination of chromium using 2,2'-bipyridine. The base electrolyte used is 0.1 M NH4Cl (pH 6.0). The peak current was found to increase substantially with the addition of nitrite ions. A well-defined peak was observed at -1.3 V. Parameters, like concentration of the ligand, concentration of nitrite ion, accumulation potential, accumulation time, rest period, drop size, scan rate, pulse amplitude etc. have been optimized. Under the optimum conditions, the 3 sigma detection limit was found to be 0.02 ppb (3.8 x 10(-10) M). The method is highly selective and sensitive, and has been applied to the determination of Cr(VI) in spiked water, effluents and ore samples.     

Method for the determination of chromium (VI) as chromium (VI)-dibenzyidithiocarbamate

Dibenzyldithiocarbamic acid (DBDC) exhibits the ability to speciate between chromium(VI) and chromium(III), since only the chromium(VI) will form complexes with DBDC. The complex is then extracted into an organic solvent and assayed using an ultraviolet-visible (UV-VIS) spectrophotometer at 498.8 nm. Using 250 ml of aqueous sample detection limits less than 1 ng/ml are possible, while the linear range extends to 500 gmg/ml when working at 498.8 nm. Oxidation of the chromium(III) to chromium (VI) using cerium (IV) enables the determination of total chromium and subsequently the chromium (III) in solution. Evaluation of the method with a standard reference material produced only 4.81 part per thousand error in the determination of chromium(VI).     

Chemically selective membrane optode for Cr(VI) determination in aqueous samples

A methodology for simultaneous preconcentration and determination of Cr(VI) from aqueous samples was developed using a membrane optode formed by physical inclusion of a Cr(VI) selective chromophore 1,5-diphenylcarbazide (DPC) into a plasticized cellulose triacetate matrix. The inclusion of an anion exchanger (Aliquat-336) was found to be effective for immobilization of both DPC and Cr(VI)-DPC complex in the optode matrix itself. The proportionality in intensity of the magenta color on the optodes loaded with varying amounts of Cr(VI) suggests its potential applications for screening of Cr(VI) in aqueous samples by visual colorimetry. On loading high amounts of Cr(VI) in the membrane optode, its color changes from magenta to yellow, which indicates the possibility of using it as a threshold detector for Cr(VI). The membrane optode was optimized in terms of obtaining maximum preconcentration efficiency for Cr(VI) and subsequent stable optical response proportional to the amount of Cr(VI) in the membrane optode sample. The membrane optodes were tested for Cr(VI) determination in tap water and seawater samples. Using this optode, Cr(VI) even at levels of 13.6 ppb could be quantitatively detected. The optodes developed in the present work were found to be stable, cost effective, easy to prepare and efficient for direct preconcentration and determination of Cr(VI) in a variety of aqueous samples using spectrophotometry. However, this membrane optode is for one time use only as the reaction of Cr(VI) with DPC is irreversible.     

Single-column ion-chromatographic determination of chromium(VI) in aqueous soil and sludge extracts

Single-column ion-chromatography (SCIC) was investigated as a routine, rapid, precise and selective analytical method for the determination of chromium(VI) in aqueous extracts of soil and sewage sludge. Chromatographic parameters were optimized for determination of Cr(VI), NO(-)(3) and SO(2-)(4). A low-capacity resin-based column was used for the separation and the anions were determined by conductometric detection. p-Hydroxybenzoic acid (5mM) at pH 8.5 was used as the eluent. The limit of detection, defined as S/N = 3, was 92 mug/l. The resolution between Cr(VI) and SO(2-)(4) was 2.8, the precision ranged from 0.9% for NO(-)(3) to 2.0% for Cr(VI) with a 500-mul injection. The SCIC results for Cr(VI) agreed closely with those obtained by inductively coupled argon-plasma emission and spectrophotometry.     

Ion-chromatographic determination of chromium (VI)

Summary A simple ion-chromatographic method has been developed for the selective determination of chromium (VI) using UV-photometric detection. The anion exchanger was based on a matrix of a 2-hydroxyethyl-methacrylate copolymer; the mobile phase consisted of phosphate buffer and sodium perchlorate. The relative standard deviation was 2.26%. Application was made to waste waters of the metallurgical industry.     

Facile preparation of glutathione-stabilized gold nanoclusters for selective determination of chromium (III) and chromium (VI) in environmental water samples

A novel method for selective determination of Cr(III) and Cr(VI) in environmental water samples was developed based on target-induced fluorescence quenching of glutathione-stabilized gold nanoclusters (GSH-Au NCs). Fluorescent GSH-Au NCs were synthesized by a one-step approach employing GSH as reducing/protecting reagent. It was found that Cr(III) and Cr(VI) showed pH-dependent fluorescence quenching capabilities for GSH-Au NCs, and thus selective determination of Cr(III) and Cr(VI) could be achieved at different pHs. Addition of EDTA was able to effectively eliminate the interferences from other metal ions, leading to a good selectivity for this method. Under optimized conditions, Cr(III) showed a linear range of 25–3800 μg L⁻¹ and a limit of detection (LOD) of 2.5 μg L⁻¹. The Cr(VI) ion demonstrated a linear range of 5–500 μg L⁻¹ and LOD of 0.5 μg L⁻¹. The run-to-run relative standard deviations (n = 5) for Cr(III) and Cr(VI) were 3.9% and 2.8%, respectively. The recoveries of Cr(III) and Cr(VI) in environmental water samples were also satisfactory (76.3–116%). This method, with its simplicity, low cost, high selectivity and sensitivity, could be used as a promising tool for chromium analysis in environmental water samples.     

Selective fluorescence determination of chromium (VI) in water samples with terbium composite nanoparticles

The strong fluorescence Tb/acetyl acetone (acac)/Poly (Acrylamide) (PAM) composite nanoparticles have been prepared under ultrasonic radiation. The nanoparticles were water-soluble, stable and have extremely narrow emission bands and high internal quantum efficiencies. Based on the fluorescence quenching of Tb/acac/PAM by Cr (VI), a method for the selective determination of Cr (VI), without separation of Cr (III) in water, was developed. The reaction condition between Cr (VI) and Tb/acac/PAM were investigated in detail. Under optimal experimental conditions, the linear calibration curve was obtained over the concentration range of 5-600 ng mL(-1) with a correlation coefficient of 0.9939. The corresponding detection limit is 0.8 ng mL(-1) and the relative standard deviation is 1.5% for 0.05 microg mL(-1) (n=7). The proposed method has been applied to the selective quantification of Cr (VI) in synthetic samples and waste-water samples with the satisfactory results. The assay is characterized by short reaction time, very few interference, stable fluorescence signals, simple instrument and simplicity.     

Ion-pair chromatographic determination of chromium(VI)

Ion-pair chromatography (IPC) with conductometric detection was investigated as a precise and selective analytical method for the determination of chromium in electro-plating solutions and waste waters. Chromatographic parameters were optimized for separation of Cr(VI) and SO(2-)(4). The analytical column (100 x 6 mm) was packed with 10 mum silasorb C(18) (Czechoslovakia). Tetrabutylammonium butyrate (TBAB), at pH 7.0 in acetonitrile-water (18:82 v/v) mixture, was used as the eluent. Two samples of solution are taken for the analysis. In the first of them the amount of Cr(VI) is determined, in the second one Cr(III) is oxidized to Cr(VI) with H(2)O(2) in alkaline medium and the total amount of Cr is determined. From the difference of the two obtained results the concentration of Cr(III) is calculated. The detection limit of Cr(VI) is 0.1 mug/ml and the relative standard deviation (at the 1.0 mug/ml) is 4.0%. The IPC results for chromium agreed closely with these obtained by spectrophotometry.     

Indirect spectrophotometric determination of chromium(VI)

A new simple and sensitive spectrophotometric method for the determination of chromium(VI) is established. It relies upon the oxidation of iron(II) with the titled ion, in acidic medium, to form iron(III) which is complexed with tiron to form a stable blue color with maximum absorption at 650 nm. Adherence to Beer's law is observed in the range 10–100 μg of chromium(VI) per 25 ml, with a molar absorptivity of 5.6 × 10³ liters mol^?1 cm^?1, sensitivity index of 0.0093 μg cm^?1, relative error of ?5.0 to +0.3%, and relative standard deviation of 0.3–4.0%, depending on the concentration level. Furthermore, the reaction needs neither temperature control nor an extraction step.     

Simultaneous determination of chromium(III) and chromium(VI) in aqueous solutions by ion chromatography and chemiluminescence detection.

A method for the simultaneous determination of chromium(iii) and chromium(vi) in a flow system based on chemiluminescence was developed. A Dionex cation-exchange guard column was used to separate chromium(iii) from chromium(vi), and chromium(vi) was reduced by potassium sulfite, whereupon both species were detected by use of the luminol-hydrogen peroxide chemiluminescence system. Linear calibration for both species was established over the concentration range 1-1000 micrograms l-1. The precision at the 20 micrograms l-1 level was 3.5% for chromium(iii) and 3.3% for chromium(vi), respectively. The detection limit was 0.5 micrograms l-1 for both species. Data were in agreement with Zeeman-effect background corrected atomic absorption spectrometry measurements.     

Highly sensitive and selective electrochemical detection of sub-ppb level chromium(VI) using nano-sized gold particle

Gold nanoparticle based nanostructured electrode has been developed for the amperometric detection of ultratrace amount of toxic Cr(VI). The nano-sized Au particles have been grown on a conducting substrate modified with sol-gel-derived thiol functionalized silicate network and used for the electroanalysis of Cr(VI). The nanostructured interface show well-defined voltammetric peak for the reduction of Cr(VI) at approximately 0.4 V. The voltammetric behavior of Cr(VI) strongly depends on the coverage of nanoparticle on the electrode surface. Constant potential amperometry has been used for the detection of Cr(VI) at well below the guideline value set by World Health Organization (WHO). This electrode is highly sensitive (30+/-0.2 nA/ppb) and the detection limit (S/N=9) was 0.1 ppb. Cr(III) and coexisting other metal ions and surface active agent present in water do not interfere with the amperometric measurement of Cr(VI). This nanostructured electrode is highly stable and it can be used for continuous measurement of Cr(VI) without using any pretreatment or activation procedures. The accuracy of the measurement has been validated by measuring the concentration of Cr(VI) in the certified reference material (CRM).     

Optode for uranium(VI) determination in aqueous medium

A quantification procedure of trace elements during colloid size fractionation was developed and validated. This procedure is based on the hyphenation between Asymmetrical Flow Field-Flow Fractionation (As-Fl-FFF) and Inductively Coupled Plasma Mass Spectrometer (ICP-MS). The optimisation of the procedure was performed on a soil leachate spiked with six trace elements selected for their environmental and health impact (As, Cd, Sb, Se, Sn and Pb). The elements in the spiked sample were on-line monitored during the fractionation. The validation was carried out by comparison with a second off-line quantification procedure based on fraction collection and total element analysis by ICP-MS. This off-line one was previously validated using reference materials. Finally, the analytical performances of the two procedures were compared.     

Spectrophotometric determination of chromium(VI) with ferron

Chromium(VI) gives a pink coloured solution in chloroform in the presence of ferron when extracted from slightly acidic medium. This reaction is used for the spectrophotometric determination of chromium by measuring the absorbance at 510 nm. Beers law is obeyed in the range of 5–70 g/ml. Most of the important metal ions do not interfere. The relative standard deviation is 2.78%.     

Highly active nanoscale zero-valent iron (nZVI)-Fe3O4 nanocomposites for the removal of chromium(VI) from aqueous solutions

For the first time, nanoscale zero-valent iron (nZVI)-Fe(3)O(4) nanocomposites, prepared by an in situ reduction method, are employed for chromium(VI) removal in aqueous environment. 96.4% Cr(VI) could be removed by these novel materials within 2h under pH of 8.0 and initial Cr concentration of 20 mg L(-1), compared with 48.8% by bare nFe(3)O(4) and 18.8% by bare nZVI. Effects of several factors, including mass composition of nZVI-Fe(3)O(4) nanocomposites, initial pH and Cr(VI) concentration, were evaluated. The optimal ratio of nFe(3)O(4) to nZVI mass lies at 12:1 with a fixed nZVI concentration of 0.05 g L(-1). Low pH and initial Cr(VI) concentration could increase both the Cr(VI) removal efficiency and reaction rate. Corresponding reaction kinetics fitted well with the pseudo second-order adsorption model. Free energy change (ΔG) of this reaction was calculated to be -4.6 kJ mol(-1) by thermodynamic study, which confirmed its spontaneous and endothermic characteristic. The experimental data could be well described by the Langmuir and Freundlich model, and the maximum capacity (q(max)) obtained from the Langmuir model was 100 and 29.43 mg g(-1) at pH 3.0 and 8.0, respectively. The reaction mechanism was discussed in terms of the mutual benefit brought by the electron transfer from Fe(0) to Fe(3)O(4).     

Speciation of chromium (VI) and total chromium determination in welding dust samples by flow-injection analysis coupled to atomic absorption spectrometry

We have studied the speciation of chromium (VI) in stainless-steel welding dusts. The approach used for the analysis of Cr(VI) and total Cr relies on a flow-injection analyzer (FIA) equipped with two different sequential detectors. The system measures Cr(VI). by colorimetry (with 1,5-diphenyl carbohydrazide) and total chromium content by flame atomic absorption spectroscopy (AAS). The extraction of the samples of welding-fume dusts is achieved in a buffer solution (acetic acid and sodium acetate at pH 4). This extraction procedure gives a 96% recovery of chromium (VI). The FIA-AAS system that has been described is also more sensitive, has a lower detection limit (0.005 mug ml(-1)) and gives a better precision (< 1%) than other equivalent systems that have been previously described.     

Spectrophotometric determination of chromium (VI) with Methylene Blue

The interaction of Cr(VI) and the thiazine dye Methylene Blue has been examined. The ion-associate formed is extractable into 1,2-dichlorethane. The optimum conditions have been established, and values obtained for the conditional extraction constant K'(ex), distribution constant K'(D) and association constant beta'. A sensitive and selective method for determination of microquantities of Cr(VI) in soils and alloys is suggested.