Synthesis and characterization of submicron size particles of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by microemulsion route

Among the various positive electrode materials investigated for Li-ion batteries, spinel LiMn₂O₄ is one of the most important materials. Small particles of the active materials facilitate high-rate capability due to large surface to mass ratio and small diffusion path length. The present work involves the synthesis of submicron size particles of LiMn₂O₄ in a quaternary microemulsion medium. The precursor obtained from the reaction is heated at different temperatures in the range from 400 to 900 °C. The samples heated at 800 and 900 °C are found to possess pure spinel phase with particle size <200 nm, as evidenced from XRD, SEM, and TEM studies. The electrochemical characterization studies provide discharge capacity values of about 100 mAh g⁻¹ at C/5 rate, and there is a moderate decrease in capacity by increasing the rate of charge–discharge cycling. Studies also include charge–discharge cycling and ac impedance studies in temperature range from −10 to 40 °C. Impedance data are analyzed with the help of an equivalent circuit and a nonlinear least squares fitting program. From temperature dependence of charge-transfer resistance, a value of 0.62 eV is obtained for the activation energy of Mn³⁺/Mn⁴⁺ redox process, which accompanies the intercalation/deintercalation of the Li⁺ ion in LiMn₂O₄.     

Effects of Ni-ion doping on electrochemical characteristics of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> powders prepared by a spray-drying method

Spinel LiMn_2−x Ni _x O₄ compounds doped with a range of Ni (x=0–0.06) were synthesized by a spray-drying method. The structure and morphology characteristics of the powders were studied in detail by means of X-ray diffraction (XRD), scanning electron microscopy, and transmission electron microscopy. The XRD data reveal that all the samples have well-defined spinel structure, but, with the increase in Ni content, the doped lithium manganese spinels have smaller lattice constant. The undoped and doped spinel LiMn₂O₄ particles are fine, narrowly distributed, and well crystallized. The electrochemical characteristics of the samples are measured in the coin-type cells in a potential range of 3.2–4.35 V vs Li/Li⁺. All cyclic voltammogram curves exhibit two pairs of redox reaction peaks, but, among them, there are some differences about the peak split. With the increase in the Ni content, the specific capacities of the samples decrease slightly, but their cyclic ability increases.     

A novel method to fabricate lithium-ion polymer batteries based on LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>/NG electrodes

A novel method to fabricate lithium-ion polymer batteries (LiPBs) has been developed. The LiPBs was fabricated without microporous polyolefin separators, taking spinel lithium manganese oxide (LiMn₂O₄) and natural graphite (NG) as the electrodes. The thicknesses of the cathodes and the anodes are 190 and 110 μm, respectively. The NG anode was coated with a microporous composite polymer film (20 μm thick) which composed of polymer and ultrafine particles. The coating process was effective and simple to be used in practical application, and ensured the composite polymer film to act as a good separator in the LiPB. The LiPBs assembled with the coated NG anodes and pristine LiMn₂O₄ cathodes presented better electrochemical performances than liquid lithium-ion battery counterparts, proving that the microporous composite polymer film can improve the performance of the coated NG anode. In this paper, the spinel LiMn₂O₄/(coated)NG-based LiPBs exhibited high rate capability, compliant temperature reliability, and significantly, excellent cycling performance under the elevated temperature (55°C).     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.     

Analysis of the temperature dependence of the high-frequency EMR spectra of Mn ions in the lithium-ion battery material LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>

This paper deals with the analysis of the temperature dependence of high-frequency EMR (HF-EMR) spectra due to Mn³⁺ and Mn⁴⁺ ions in the lithium manganese spinel LiMn₂O₄. A range of powder samples obtained by the sol-gel method with calcinations in several temperature ranges were prepared for this study. Based on the initial characterization carried out by a number of techniques, the physicochemical and structural properties of the samples were earlier determined. Independently, temperature magnetization and HF-EMR measurements were carried out. The EMR spectra vary strongly between samples, indicating possible structural or chemical changes. Quantitative analysis of the temperature dependence of the HF-EMR spectra due to Mn³⁺ and Mn⁴⁺ ions in LiMn₂O₄ is presented in this paper. The spectral analysis concerns the line shape, linewidth, intensity and g-factors. Fittings using the Lorentzian spectral shape and, to a certain extent, the Gaussian spectral shape have been carried out in order to parameterize the temperature dependence of the HF-EMR spectra. This parameterization of the HF-EMR experimental data enables a deeper characterization of the samples. Subsequently, a better insight into the role of the Mn³⁺ and Mn⁴⁺ ions in accounting for the characteristics most suitable for application of LiMn₂O₄ as a cathode material may be gained.     

Preparation and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>composite particles

Using Fe₃O₄ nano-particles as seeds, a new type of Fe₃O₄/Au composite particles with core/shell structure and diameter of about 170 nm was prepared by reduction of Au³⁺ with hydroxylamine in an aqueous solution. Particle size analyzer and transmission electron microscope were used to analyze the size distribution and microstructure of the particles in different conditions. The result showed that the magnetically responsive property and suspension stability of Fe₃O₄ seeds as well as reduction conditions of Au³⁺to Au⁰are the main factors which are crucial for obtaining a colloid of the Fe₃O₄/Au composite particles with uniform particle dispersion, excellent stability, homogeneity in particle sizes, and effective response to an external magnet in aqueous suspension solutions. UV-Vis analysis revealed that there is a characteristic peak of Fe₃O₄/Au fluid. For particles with d(0.5)=168 nm, the λmax is 625 nm.     

Comparative study of the synthesis of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> in silica through the polymerized complex route of the sol–gel method

In this work the synthesis of CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ nanocomposites was studied via the sol–gel method, using the polymerized complex route. The polymerized precursors obtained by the reaction of citric acid, ethylene glycol, tetraethylorthosilicate, ferric nitrate, and cobalt nitrate or nickel chloride were characterized by nuclear magnetic resonance (NMR) and infrared (IR) spectroscopy. NMR and IR spectra of the precursors, without and with metallic ions, show the formation of polymeric chains with ester and ether groups and complexes of metal-polymeric precursor. The nanocomposites were obtained by the thermal decomposition of the organic fraction and characterized by X-ray diffraction (XRD) and vibrating sample magnetometry (VSM). XRD patterns show the formation of CoFe₂O₄ and NiFe₂O₄ in an amorphous silica matrix above 400 °C in both cases. When the calcination temperature was 800 °C the particle size of the crystalline phases, calculated using the Scherrer equation, reached ∼35 nm for the two oxides. VSM plots show the ferrimagnetic behavior that is expected for this type of magnetic material; the magnetization at 12.5 KOe of the CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ compounds was 29.5 and 17.4 emu/g, respectively, for samples treated at 800 °C.     

Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Electrochemical properties of nano-crystalline LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> synthesized by polymer-pyrolysis method

LiNi_0.5Mn_1.5O₄ powders were prepared through polymer-pyrolysis method. XRD and TEM analysis indicated that the pure spinel structure was formed at around 450 °C due to the very homogeneous intermixing of cations at the atomic scale in the starting precursor in this method, while the well-defined octahedral crystals appeared at a relatively high calcination temperature of 900 °C with a uniform particle size of about 100 nm. When cycled between 3.5 and 4.9 V at a current density of 50 mA/g, the as prepared LiNi_0.5Mn_1.5O₄ delivered an initial discharge capacity of 112.9 mAh/g and demonstrated an excellent cyclability with 97.3% capacity retentive after 50 cycles.     

Preparation and electrochemical properties of V<Subscript>2</Subscript>O<Subscript>5</Subscript> submicron-belts synthesized by a sol–gel H<Subscript>2</Subscript>O<Subscript>2</Subscript> route

One-dimensional (1D) submicron-belts of V₂O₅ have been prepared by a sol–gel route using V₂O_5, H₂O₂ and aniline as starting materials. Thermogravimetric and differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy were employed to characterize the samples. Electrochemical behaviors as cathode material in rechargeable lithium-ion batteries were investigated by galvanostatic charge–discharge measurement and cyclic voltammeter. The results showed that the synthesized V₂O₅ appeared to be submicron-belts and orthorhombic structure. The V₂O₅ submicron-belts exhibited a high initial discharge capacity of 346 mAh/g and stayed 240 mAh/g after 20 cycles at 0.1 C discharge rate in the potential region 1.8–4.0 V.     

Modeling the active centers of V<Subscript>2</Subscript>O<Subscript>5</Subscript>/SiO<Subscript>2</Subscript> and V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> supported catalysts. DFT theoretical analysis of optical properties

Within the framework of the density functional theory (DFT), the electronic structure of monooxodioxovanadium functional groups in tetrahedral coordination, which model the active centers (ACs) of fine supported catalysts V₂O₅/SiO₂ and V₂O₅/TiO₂, has been analyzed. The optimal structures of three ACs as possible models of monomeric and polymeric oxovanadium forms on the carriers with low vanadium content were determined. The modified DFT method involving the time dependence of Kohn-Sham equation (TDDFT) was used for the adopted AC models to calculate the energies of the excited states, and optical spectra of the absorption in 25000–60000 cm^?1 region were reconstructed on their base. The spectrum in this region is due to O → V charge transfer. The features of electronic spectra with the charge transfer for V₂O₅/SiO₂ and V₂O₅/TiO₂ catalysts and the vibrational spectra of three AC models corresponding to the monomeric and dimeric oxovanadium forms of the supported catalysts V₂O₅/SiO₂ and V₂O₅/TiO₂ were defined. The detailed interpretation of normal vibration frequencies is given. The frequencies typical of the monomeric and dimeric oxovanadium forms on the carrier surface were identified.     

Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Au composite nano-particles and their optical properties

Fe₃O₄/Au composite particles with core/shell structure were prepared by reduction of Au³⁺ with hydroxylamine in the presence of an excess of Fe₃ O₄ as seeds. The resultant colloids, with an average diameter of less than 100 nm, were obtained; the remaining non-reacted Fe₃O₄ seeds can be removed by treatment with diluted HCl solution. The Fe₃O₄/Au colloids exhibit a characteristic peak of UV-visible spectra, which largely depend on the size of the particle and the suspension medium. The localized surface plasmon resonance peaks red shift and broaden with increased nanoparticle diameter or increased solvent ionic strength. The optical property is very important in the establishment of means for the detection of biomolecules.     

Enhanced electrochemical performance of submicron LiCoO<Subscript>2</Subscript> synthesized by polymer pyrolysis method

Submicron LiCoO₂ was synthesized by a polymer pyrolysis method using LiOH and Co(NO₃)₂ as the precursor compounds. Experimental results demonstrated that the powders calcined at 800 °C for 12 h appear as well-crystallized, uniform submicron particles with diameter of about 200 nm. As a result, the as-prepared LiCoO₂ electrode displayed excellent electrochemical properties, with an initial discharge capacity of 145.5 mAh/g and capacity retention of 86.1% after 50 cycles when cycled at 50 mA/g between 3.5 and 4.25 V. When cycled between 3.5 and 4.5 V, the discharge capacity increased to 177.9 mAh/g with capacity retention of 85.6% after 50 cycles.     

Lithium AlPO<Subscript>4</Subscript> composite polymer battery with nanostructured LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode

The borate ester plasticized AlPO₄ composite solid polymer electrolytes (SPE) have been synthesized and studied as candidates for lithium polymer battery (LPB) application. The electrochemical and thermal properties of SPE were shown to be suitable for practical LPB. Nanostructured LiMn₂O₄ with spherical particles was synthesized via ultrasonic spray pyrolysis technique and has shown a superior performance to the one prepared via conventional methods as cathode for LPB. Furthermore, the AlPO₄ addition to the polymer electrolyte has improved the polymer battery performance. Based on the AC impedance spectroscopy data, the performance improvement was suggested as being due to the cathode/polymer electrolyte interface stabilization in the presence of AlPO₄. The Li/composite polymer electrolyte/nanostructured LiMn₂O₄ electrochemical cell showed stable cyclability during the various current density tests, and its performance was found to be quite acceptable for practical utilities at ambient temperature and showed remarkable improvements at 60 °C compared with the solid state reaction counterpart.     

Preparation of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>-C18 nano-magnetic composite materials and their cleanup properties for organophosphorous pesticides

Magnetic Fe₃O₄-C18 composite nanoparticles of approximately 5–10 nm in size were synthesized and characterized by IR spectroscopy, atomic absorption spectroscopy, X-ray diffraction, and transmission electron microscopy. The magnetic Fe₃O₄-C18 composite nanoparticles were applied for cleanup and enrichment of organophosphorous pesticides. Comparative studies were carried out between magnetic Fe₃O₄-C18 composite nanoparticles and common C18 materials. Residues of organophosphorous pesticides were determined by gas chromatography in combination with a nitrogen/phosphorus detector. The cleanup and enrichment properties of magnetic Fe₃O₄-C18 composite nanoparticles are comparable with those of common C18 materials for enrichment of organophosphorous pesticides, but the cleanup and enrichment are faster and easier to perform. Figure Presumed mechanism for the adhesion of the OPs to the Fe₃O₄-C18 magnetic nanoparticles     

Phase relations in the CoO–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system in subsolidus area

Thermal properties of Co₂FeV₃O₁₁ have been reinvestigated. It has been proved that this compound does not exhibit polymorphism. It melts incongruently at the temperature of 770±5°C and the phase with lyonsite type structure is the solid product of this melting. Phase relations in the whole subsolidus area of the CoO–V₂O₅–Fe₂O₃ system have been determined. The solidus area projection onto the component concentration triangle plane of this system has been constructed using the DTA and XRD methods. 15 subsidiary subsystems can be distinguished in this system.     

2-pyrrolidone - capped Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocrystals

Water-soluble Mn₃O₄ nanocrystals have been prepared through thermal decomposition in a high temperature boiling solvent, 2-pyrrolidone. The final product was characterized with XRD, SEM, TEM, FTIR and Zeta Potential measurements. Average crystallite size was calculated as ∼15 nm using XRD peak broadening. TEM analysis revealed spherical nanoparticles with an average diameter of 14±0.4 nm. FTIR analysis indicated that 2-pyrrolidone coordinates with the Mn₃O₄ nanocrystals only via O from the carbonyl group, thus confining their growth and protecting their surfaces from interaction with neighboring particles.      

Preparation and characterization of LiFePO<Subscript>4</Subscript> from NH<Subscript>4</Subscript>FePO<Subscript>4</Subscript>·H<Subscript>2</Subscript>O under different microwave heating conditions

Olivine-type LiFePO₄ is a very promising polyanion-type cathode material for lithium-ion batteries. In this work, LiFePO₄ with high specificity capacity is obtained from a novel precursor NH₄FePO₄·H₂O via microwave processing. The grains grow up in the duration of sintering until they reach the decomposition temperature. The apparent conductivity of the samples rises rapidly with the irradiation time and influences the electrochemical performance of the material greatly at high current density. As a result, the LiFePO₄ cathode material obtained with a sintering time of 15 min has good electrochemical performance. Between 2.5 and 4.2 V versus Li, a reversible capacity is as high as 156 mAh g⁻¹ at 0.05 C.     

Temperature dependence of the polarization resistance of the O<Subscript>2</Subscript>,Au/La<Subscript>0.88</Subscript>Sr<Subscript>0.12</Subscript>Ga<Subscript>0.82</Subscript>Mg<Subscript>0.18</Subscript>O<Subscript>2.85</Subscript> electrode system

The impedance of a porous gold electrode in contact with solid electrolyte La_0.88Sr_0.12Ga_0.82Mg_0.18O_2.85 and the effect of the manufacture conditions on its polarization resistance are studied at 600–800°C in air. The overall oxygen reaction rate on a gold electrode is described as the sum of two partial constituents, namely, the oxygen exchange at the gas/electrolyte interface at the gold/gas/electrolyte triple-phased boundary.Translated from Elektrokhimiya, Vol. 41, No. 2, 2005, pp. 190–197.Original Russian Text Copyright © 2005 by Shkerin, Sokolova, Khlupin, Beresnev.This revised version was published online in April 2005 with corrections to the article note and article title and cover date.