SO42-/ZrO2的制备工艺对催化橡胶籽油裂解油酯化的影响

以SO₄^2-/ZrO₂为催化剂对橡胶籽油裂解油进行甲酯化。研究了锆源、焙烧温度及焙烧时间对催化剂活性的影响,分别采用氨气吸附程序升温脱附(NH₃-TPD)和吡啶红外(Py-IR)对固体酸SO₄^2-/ZrO₂的酸性和酸型进行分析。实验结果表明,以ZrOCl₂为锆源,550℃焙烧4 h所得固体酸SO₄^2-/ZrO₂的催化活性最好,性能较稳定。对酯化产物的组成及性能进行了考察,结果表明,酯化产物的各项性能均优于传统工艺制备的生物燃油,且与0^#柴油相近。     

固体酸SO42-/ZrO2-CeO2催化小桐子油脂肪酸制备生物柴油的实验研究

用沉淀浸渍法制备了固体酸催化剂SO₄^2-/ZrO₂-CeO₂,用于催化小桐籽油脂肪酸与甲醇酯化制备生物柴油。考察了焙烧温度和CeO₂负载量对催化剂活性的影响,并进行了单因素实验和动力学研究。研究表明,SO₄^2-/ZrO₂-CeO₂有较高的催化活性,当甲醇与脂肪酸体积比 2∶1,反应温度150 ℃,催化剂用量为脂肪酸质量的8%,反应60 min时,脂肪酸转化率可达0.9403。动力学计算表明,该酯化反应的表观活化能为45.31 kJ/mol,动力学模型为-dc_A/dt=38371e^-45310/RTc_A^1.44。     

焙烧温度对微乳液法负载铂制备的Pt-S2O82-/ZrO2-Al2O3催化剂异构化性能的影响

过微乳液法负载Pt制备了Pt-S₂O₈^2-/ZrO₂-Al₂O₃(Pt-SZA-X) 催化剂,并采用XRD、BET、FT-IR、TPR、TEM等手段对催化剂进行了表征。以正戊烷异构化反应为探针,考察了焙烧温度对催化剂异构化性能的影响。结果表明,焙烧温度对Pt-SZA-X的还原温度影响不大,但催化剂表面S含量随着焙烧温度的升高而下降;焙烧温度为600~650℃时形成O=S=O结构,此时S与催化剂载体结合比较稳定;焙烧温度为650℃时,可得到单一的ZrO₂四方晶相,焙烧温度高于650℃时,比表面积迅速降低,催化剂表面S⁶⁺流失严重。在不同温度下焙烧得到的催化剂中,经650℃焙烧的催化剂具有适宜的超强酸位和比表面积,异构化活性最高。在反应温度为230℃、反应压力2.0 MPa、氢烃物质的量比4:1、质量空速1.0 h^-1时,催化异戊烷产率达到60.8%。     

钨含量对固体超强酸催化剂Pd-SO42-/ZrO2-WO3异构化性能的影响

为了研究Pd-SO₄^2-/ZrO₂-WO₃型固体超强酸催化剂的异构化性能,以正戊烷异构化为探针反应, 考察了钨(W)含量对催化剂异构化性能的影响。采用X射线衍射(XRD)、FT-IR、H₂-TPR、比表面积测定(BET)、热重-差热分析(TG-DTA)和氨-程序升温脱附(NH₃-TPD)手段对催化剂进行了表征,分析了WO₃含量对催化剂酸性、比表面积、氧化还原能力以及晶体结构的影响。结果表明,当WO₃的质量分数为13%焙烧温度为600℃时, Pd-SO₄^2-/ZrO₂-WO₃固体超强酸催化剂的催化活性最好。在反应温度260℃,压力2.0MPa,质量空速1.0h^-1,氢油比为4.0时,异物烷产率为40.1%。在80h内异戊烷收率可稳定在38%左右,选择性在95.3％以上。     

SO42-/ZrO2和SO42-/Al2O3-ZrO2催化剂上的正戊烷反应

研究了添加Al对SO₄^2-/ZrO₂超强酸样品的晶化、比表面、硫含量、超强酸性和正戊烷反应性能的影响,考察了活化温度、反应温度、Al含量和载Pt对催化剂活性和选择性的影响.SO₄^2-/Al₂O₃ZrO₂催化剂的酸强度与SO₄^2-/ZrO₂基本相当,但超强酸位比后者多,未载Pt时正戊烷反应活性和稳定性明显高于后者.负载Pt后,正戊烷异构化选择性和稳定性大大提高,但Pt/SO₄^2-/Al₂O₃ZrO₂催化剂的反应活性与Pt/SO₄^2-/ZrO₂相近,Al的促进作用不明显.     

Pd含量对SO42-/ZrO2-WO3固体超强酸催化剂其异构化性能的影响

制备了Pd-SO₄^2-/ZrO₂-WO₃型固体超强酸催化剂,并采用XRD、FT-IR、TPR、XPS、BET和TG-DTA等表征手段对催化剂进行了表征。以正戊烷异构化为探针反应,考察了Pd含量对催化剂异构化活性的影响。结果表明,Pd可以明显地降低催化剂的还原温度,提高催化剂中SO₄^2-的分解温度,从而提高了催化剂热稳定性。当Pd质量分数为0.05%时,Pd-SO₄^2-/ZrO₂-WO₃固体超强酸催化剂的催化活性最好。该催化剂在反应温度260℃、反应压力2.0 MPa、质量空速为1.0 h^-1、氢油比为4.0时,异戊烷收率和液收率为40.1%和93.9%。     

双酸体系下有序介孔SO42-/ZrO2-SiO2材料的合成

采用一锅合成法通过调变自组装过程中硫酸和盐酸的体积比,成功制备了系列介孔SO₄^2-/ZrO₂-SiO₂固体酸材料(Zr/Si物质的量为1.1).XRD、UV-Vis DRS、HR-TEM等表征结果表明,所得材料均具有高度有序的二维介孔结构及四方相氧化锆的晶体结构.氮吸附和FT-IR表征结果进一步发现,通过改变硫酸/盐酸体积比可有效调变材料比表面积、孔容、孔径及表面L酸与B酸的相对强度.与纯硅介孔分子筛SBA-15不同,此系列SO₄^2-/ZrO₂-SiO₂固体酸材料均在正戊烷的异构化反应中表现出较高的催化活性和稳定性.其原因在于,在合成过程中硫酸的加入不仅促使了酸基的形成,而且稳定了催化剂的晶体结构;盐酸的存在则保持了有序的介孔结构.由此可见,混酸合成体系有望制备出结构有序、酸性可调、催化性能优越的新型催化材料,并在众多酸催化反应中取得应用.     

Al含量对Pt-S2O82-/ZrO2-Al2O3型固体超强酸催化剂异构化性能的影响

通过向S₂O₈^2-/ZrO₂催化剂中同时引入适量的Pt和Al₂O₃, 制备出了具有较高催化性能和高稳定性的Pt-S₂O₈^2-/ZrO₂-Al₂O₃型固体超强酸催化剂. 以正戊烷异构化反应为探针, 考察了Al含量对催化剂的异构化性能的影响, 并采用XRD, BET, FTIR, TPR, TG-DTA, NH₃-TPD和ICP手段对催化剂进行了表征. 结果表明, Al能够延迟ZrO₂的晶化温度, 抑制硫的分解; Al能够增加催化剂的比表面积, 增强硫氧键的结合, 提高催化剂的还原性能, 增加催化剂的酸强度和酸总量. 当Al₂O₃质量分数为2.5%时, Pt-S₂O₈^2-/ZrO₂-Al₂O₃固体超强酸催化剂的催化活性最高, 正戊烷异构化收率可达60.02%, 选择性在98.2％以上.     

高酸值生物柴油原料甘油酯化脱酸研究

利用共沉淀-浸渍法制备了Al改性固体酸催化剂SO₄^2-/ZrO₂,考察了催化剂在甘油酯化脱酸制备生物柴油原料反应中的催化活性、重复利用性和再生性能,并对使用前后的催化剂进行了红外光谱分析。研究表明,添加适量Al(1%,以Al₂O₃的质量分数计)不但提高了催化剂的活性,还改善了催化剂的重复利用性和再生性能。添加Al使ZrO₂上SO₄^2-的量增加,SO₄^2-结合强度增强,减少了在酯化脱酸反应过程中SO₄^2-的流失。在SO₄^2-/ZrO₂-Al₂O₃催化剂用量为7％、甘油与酸物质的量比为6:1、反应温度为140 ℃、反应时间为4 h的条件下,酯化率可达91%以上,可将高酸值油脂的酸值从31 mg_KOH/g降低到2.8 mg_KOH/g以下,可满足生物柴油原料的要求。     

SO42-/MxOy型固体超强酸催化剂研究(Ⅰ)

合成了一种新的SO₄^2-/M_xO_y型固体超强酸-SO₄^2-/ZrO₂-Fe₂O₅,研究了它对正戊烷反应的活性与选择性;制备并测定了SO₄^2-/TiO₂固体超强酸对正戊烷的异构化活性与裂解活性及其某些物性;重复合成了文献报导的SO₄^2-/ZrO₂固体超强酸并测定了它对正戊烷异构化的催化性能,表明所采用的测定方法与所得结果可与文献值相比较。     

固体超强酸SO2-4/ZrO2的制备及其催化性能研究

以氧氯化锆为锆原,氨水为沉淀剂,硫酸溶液为浸渍液,通过沉淀-浸渍法制备SO2-4/ZrO2(SZ)酯化催化剂,其结构经BET、X-射线衍射(XRD)、傅立叶变换红外光谱(FT-IR)及扫描电子显微镜(SEM)表征.结果表明:随着焙烧温度升高,催化剂的比表面积依次降低,孔径增大,氧化锆的晶态由无定形态转化为四方晶态再转化为单斜晶态;于600℃焙烧时,催化剂形成的S=O键红外吸收峰最强;于700℃焙烧时,催化剂结构被破坏.在丙烯酸与十八醇的酯化反应中对催化剂进行活性测试.结果表明:600℃焙烧的催化剂产率最高(96.4%).     

The Effect of Sulfate Ion on the Isomerization of n-Butane to iso-Butane

The effect of sulfate ion (SO42-) loading on the properties of Pt/SO42- -ZrO2 and on the catalytic isomerization of n-butane to iso-butane was studied. The catalyst was prepared by impregnation of Zr(OH)4 with H2SO4 and platinum solution followed by calcination at 600℃. Ammonia TPD and FT-IR were used to confirm the distribution of acid sites and the structure of the sulfate species. Nitrogen physisorption and X-ray diffraction were used to confirm the physical structures of Pt/SO42--ZrO2. XRD pattern showed that the presence of sulfate ion stabilized the metastable tetragonal phase of zirconia and hindered the transition of amorphous phase to monoclinic phase of zirconia. Ammonia TPD profiles indicated the distributions of weak and medium acid sites observed on 0.1 N and 1.0 N sulfate in the loaded catalysts. The addition of 2.0 N and 4.0 N sulfate ion generated strong acid site and decreased the weak and medium acid sites. However, the XRD results and the specific surface area of the catalysts indicated that the excessive amount of sulfate ion collapsed the structure of the catalyst. The catalysts showed high activity and stability for isomerization of n-butane to iso-butane at 200℃under hydrogen atmosphere. The conversion of n-butane to iso-butane per specific surface area of the catalyst increased with the increasing amount of sulfate ion owing to the existence of the bidentate sulfate and/or polynucleic sulfate species ((ZrO)2SO2), which acts as an active site for the isomerization.     

纯四方相硫化氧化锆催化剂的制备及其生物柴油合成应用研究

将过硫酸铵浸渍于直接合成的纳米氧化锆晶体表面,经300-500℃高温焙烧处理获得硫化氧化锆催化剂。采用X射线衍射（XRD）、氮气吸附-脱附、氨气程序升温脱附（NH₃-TPD）、傅里叶红外光谱（FT-IR）、扫描电镜（SEM）和能谱仪（EDS）等分析手段对催化剂的结构性能进行了表征。结果表明,所有的催化剂均展现出纯四方相结构和高的结晶度。其中,经500℃热处理获得的催化剂拥有最高的硫含量和酸性位,将其应用于大豆油与甲醇酯交换反应合成生物柴油,获得了脂肪酸甲酯收率高达84.6%的催化效果,进一步表明该催化剂表面存在优越的超强酸位。     

阴离子表面活性剂辅助模板途径合成介孔结构氧化锆纳米晶

利用阴离子表面活性剂十二烷基磺酸钠(SDS)为辅助模板剂, 成功地合成了高稳定性的介孔氧化锆纳米晶, 采用DSC-TG, FT-IR, XRD, TEM, UV-Vis以及N₂吸附-脱附等方法对样品进行了表征. 研究表明, 以阴离子型十二烷基磺酸钠合成的氧化锆经600 ℃煅烧后仍为纯四方相, 氧化锆晶粒平均尺寸约为6.5 nm. 阴离子型表面活性剂与有机锆源形成自组装协同作用, 合成的氧化锆具有蠕虫状介孔结构, 经过500 ℃煅烧后介孔结构仍然保持, 且由于表面活性剂的去除, 比表面积显著提高, 显示了良好的热稳定性. 本实验制备的氧化锆纳米晶较一般方法制备的市售纳米氧化锆有明显紫外吸收边蓝移现象.     

Synthesis and Characterization of Sol-Gel Cu-ZrO2 and Fe-ZrO2 Catalysts

Fe-ZrO₂ and Cu-ZrO₂ xerogels were prepared by a sol-gel method. The effect of the hydrolysis catalyst during the gelation step, namely H₂SO₄ or NH₄OH, on the properties of the resulting materials was investigated by XRD, BET, TGA/DTA, TPD of ammonia, FTIR, and TPR. Fe-ZrO₂ and Cu-ZrO₂ xerogels, with sulfuric acid introduced as the hydrolysis catalyst, mainly crystallyzed in the tetragonal phase and exhibited larger surface area and acid amount than those obtained with NH₄OH. Ammonia TPD shows that copper promoted sulfated zirconia is the most acidic material. TGA and FTIR reveal that under oxidizing conditions sulfated zirconia promoted with iron and copper retains more sulfate species than unpromoted sulfated zirconia. Regardless of the hydrolysis catalyst employed, copper promoted catalysts calcined at 600°C, contain a large fraction of copper oxide specieseasily reduced at low temperatures. These copper oxide species are believed to have different environment and interactions with the surface oxygen vacancies of the zirconia support. A FeO-like phase appears to be the most probable one after reduction of Fe-ZrO₂ catalysts prepared with NH₄OH as the hydrolysis catalyst. The formation of Fe° species may be hindered by the high dispersion and interaction of Fe²⁺ ions with the zirconia support. On the other hand, the reduction peaks of iron oxide and sulfate species exhibit a considerable overlap in the TPR profiles of sulfated Fe-ZrO₂ samples. Hence, the nature of the supported phase in the latter samples is rather uncertain.     

载体对Pt/WO_3-ZrO_2催化临氢异构反应性能的影响

以平衡吸附过氧钨酸的水合氧化锆为前驱体,经焙烧得到WO_3-ZrO_2固体酸,并采用XRD、UV-vis、NH_3-TPD等手段考察了过氧钨酸吸附液浓度及焙烧温度对WO_3-ZrO_2固体酸组成、结构及酸性的影响。通过BET、H_2-TPR、H_2-TPD等表征手段和正戊烷临氢异构反应,考察了负载铂后相应催化剂的结构、还原与氢吸附性质及其催化正戊烷临氢异构反应的性能。结果表明,焙烧温度为700℃时,随着吸附液浓度的增加,所得载体酸度及相应催化剂比表面积均先增加后减小,且在吸附液浓度为82 mmol W/L时达到最大值。吸附液浓度为59 mmol W/L时,随着焙烧温度的升高,所得载体四方相氧化锆含量、酸度及相应催化剂比表面积均降低。吸附液浓度为82 mmol W/L、焙烧温度为700℃所得载体负载0.5%(质量分数)铂后催化活性最高。该催化剂在250℃常压临氢操作、n(H_2)/n(n-C_5H_(12))为3、WHSV为1.0 h~(-1)的条件下,催化正戊烷异构反应中异戊烷收率可达57.7%。     

Nanocrystalline sulfated zirconia as an efficient solid acid catalyst for the synthesis of 2,3-dihydroquinazolin-4(1H)-ones

The condensation reaction of 2-aminobenzamide and aldehydes or ketones was investigated in the presence of nanocrystalline sulfated zirconia (SO₄ ^2?/ZrO₂) as solid acid catalyst. SO₄ ^2?/ZrO₂ nanoparticles with different calcination temperatures were prepared and characterized by XRD, FT-IR and SEM techniques. The results confirm good stabilization of tetragonal phase of zirconia in the presence of sulfate. The reusability experiments show partial deactivation of the catalyst due to leaching of the sulfate and coke deposition on the catalyst.     

Pd-based sulfated zirconia prepared by a single step sol–gel procedure for lean NOx reduction

Pd-based sulfated zirconia catalysts have been prepared through a single step (one-pot) sol–gel preparation technique, in which both sulfate and Pd precursors were dissolved in an organic solution before the gelation step. Observation of the calcination procedure through TGA/DSC and mass spectrometry revealed that the addition of increasing amounts of Pd resulted in the evolution of organic precursor species at lower temperatures. In situ XRD experiments showed that tetragonal zirconia is formed at lower temperatures and larger zirconia crystallites are formed when Pd is added to the gel. Although tetragonal zirconia was the only phase observed through XRD, Raman spectra of samples calcined at 700 °C showed the presence of both the tetragonal and the monoclinic phase, indicating a surface phase transition. DRIFTS experiments showed NO species adsorbed on Pd²⁺ cations. Pd/SZ catalysts prepared through this single step method were active for the reduction of NO₂ with CH₄ under lean conditions. Calcination temperature had a significant effect on this activity, with samples calcined at 700 °C being much more active than those calcined at 600 °C, despite the observed transition to the monoclinic phase. This activity may be linked to observed changes in the surface sulfate species at higher calcination temperatures.